Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 6.6 2017-11-05 r4594 [x86_64-w64-mingw32-w10-1607] (sf-6.6-1)
- Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Hitachi/HGST Travelstar Z5K500
- Device Model: Hitachi HTS545050A7E380
- Serial Number: 120912TEJ51239J5R2MX
- LU WWN Device Id: 5 000cca 71edec7c4
- Firmware Version: GG2OA7A0
- User Capacity: 500,107,862,016 bytes [500 GB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 2.5 inches
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ATA8-ACS T13/1699-D revision 6
- SATA Version is: SATA 2.6, 3.0 Gb/s
- Local Time is: Sun Jan 13 01:06:50 2019 EST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- AAM feature is: Unavailable
- APM level is: 128 (minimum power consumption without standby)
- Rd look-ahead is: Enabled
- Write cache is: Disabled
- DSN feature is: Unavailable
- ATA Security is: Disabled, NOT FROZEN [SEC1]
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: FAILED!
- Drive failure expected in less than 24 hours. SAVE ALL DATA.
- See vendor-specific Attribute list for failed Attributes.
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 45) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 106) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
- 1 Raw_Read_Error_Rate PO-R-- 084 084 062 - 7471322
- 2 Throughput_Performance P-S--- 100 100 040 - 0
- 3 Spin_Up_Time POS--- 214 214 033 - 1
- 4 Start_Stop_Count -O--C- 086 086 000 - 23340
- 5 Reallocated_Sector_Ct PO--CK 001 001 005 NOW 613
- 7 Seek_Error_Rate PO-R-- 098 098 067 - 2
- 8 Seek_Time_Performance P-S--- 100 100 040 - 0
- 9 Power_On_Hours -O--C- 071 071 000 - 13136
- 10 Spin_Retry_Count PO--C- 100 100 060 - 0
- 12 Power_Cycle_Count -O--CK 087 087 000 - 20502
- 191 G-Sense_Error_Rate -O-R-- 093 093 000 - 32
- 192 Power-Off_Retract_Count -O--CK 099 099 000 - 201
- 193 Load_Cycle_Count -O--C- 045 045 000 - 554237
- 194 Temperature_Celsius -O---- 253 253 000 - 21 (Min/Max 9/49)
- 196 Reallocated_Event_Count -O--CK 062 062 000 - 1066
- 197 Current_Pending_Sector -O---K 001 001 000 - 14376
- 198 Offline_Uncorrectable ---R-- 100 100 000 - 0
- 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0
- 223 Load_Retry_Count -O-R-- 100 100 000 - 0
- ||||||_ K auto-keep
- |||||__ C event count
- ||||___ R error rate
- |||____ S speed/performance
- ||_____ O updated online
- |______ P prefailure warning
- General Purpose Log Directory Version 1
- SMART Log Directory Version 1 [multi-sector log support]
- Address Access R/W Size Description
- 0x00 GPL,SL R/O 1 Log Directory
- 0x01 SL R/O 1 Summary SMART error log
- 0x02 SL R/O 1 Comprehensive SMART error log
- 0x03 GPL R/O 1 Ext. Comprehensive SMART error log
- 0x06 SL R/O 1 SMART self-test log
- 0x07 GPL R/O 1 Extended self-test log
- 0x09 SL R/W 1 Selective self-test log
- 0x10 GPL R/O 1 NCQ Command Error log
- 0x11 GPL R/O 1 SATA Phy Event Counters log
- 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
- 0xe0 GPL,SL R/W 1 SCT Command/Status
- 0xe1 GPL,SL R/W 1 SCT Data Transfer
- SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
- Device Error Count: 19124 (device log contains only the most recent 4 errors)
- CR = Command Register
- FEATR = Features Register
- COUNT = Count (was: Sector Count) Register
- LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
- LH = LBA High (was: Cylinder High) Register ] LBA
- LM = LBA Mid (was: Cylinder Low) Register ] Register
- LL = LBA Low (was: Sector Number) Register ]
- DV = Device (was: Device/Head) Register
- DC = Device Control Register
- ER = Error register
- ST = Status register
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 19124 [3] occurred at disk power-on lifetime: 13136 hours (547 days + 8 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 08 00 00 00 00 48 68 00 00 Error: WP at LBA = 0x00004868 = 18536
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 61 00 08 00 20 00 00 00 00 2a 28 40 00 00:01:32.209 WRITE FPDMA QUEUED
- 60 00 08 00 18 00 00 00 00 48 68 40 00 00:01:30.624 READ FPDMA QUEUED
- 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:01:30.624 READ LOG EXT
- 60 00 08 00 10 00 00 00 00 48 68 40 00 00:01:27.204 READ FPDMA QUEUED
- 60 00 08 00 08 00 00 00 00 48 60 40 00 00:01:27.204 READ FPDMA QUEUED
- Error 19123 [2] occurred at disk power-on lifetime: 13136 hours (547 days + 8 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 08 00 00 00 00 48 68 00 00 Error: UNC at LBA = 0x00004868 = 18536
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 08 00 10 00 00 00 00 48 68 40 00 00:01:27.204 READ FPDMA QUEUED
- 60 00 08 00 08 00 00 00 00 48 60 40 00 00:01:27.204 READ FPDMA QUEUED
- 60 00 08 00 f8 00 00 00 00 48 58 40 00 00:01:27.204 READ FPDMA QUEUED
- 60 00 08 00 f0 00 00 00 00 48 50 40 00 00:01:27.196 READ FPDMA QUEUED
- 61 00 08 00 e8 00 00 00 00 08 20 40 00 00:01:27.193 WRITE FPDMA QUEUED
- Error 19122 [1] occurred at disk power-on lifetime: 13136 hours (547 days + 8 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 58 00 00 00 00 48 68 00 00 Error: UNC at LBA = 0x00004868 = 18536
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 80 00 d0 00 00 00 00 48 40 40 00 00:01:23.724 READ FPDMA QUEUED
- 2f 00 00 00 01 00 00 00 00 00 10 e0 00 00:01:23.724 READ LOG EXT
- 60 00 80 00 c8 00 00 00 00 48 40 40 00 00:01:20.300 READ FPDMA QUEUED
- 60 00 80 00 c0 00 00 00 00 47 c0 40 00 00:01:20.299 READ FPDMA QUEUED
- 60 00 08 00 b8 00 00 00 00 4b b8 40 00 00:01:20.293 READ FPDMA QUEUED
- Error 19121 [0] occurred at disk power-on lifetime: 13136 hours (547 days + 8 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 58 00 00 00 00 48 68 00 00 Error: UNC at LBA = 0x00004868 = 18536
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- 60 00 80 00 c8 00 00 00 00 48 40 40 00 00:01:20.300 READ FPDMA QUEUED
- 60 00 80 00 c0 00 00 00 00 47 c0 40 00 00:01:20.299 READ FPDMA QUEUED
- 60 00 08 00 b8 00 00 00 00 4b b8 40 00 00:01:20.293 READ FPDMA QUEUED
- 60 00 01 00 b0 00 00 00 00 47 bf 40 00 00:01:20.293 READ FPDMA QUEUED
- 60 00 01 00 a8 00 00 00 00 47 be 40 00 00:01:20.293 READ FPDMA QUEUED
- SMART Extended Self-test Log Version: 1 (1 sectors)
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- SCT Status Version: 3
- SCT Version (vendor specific): 256 (0x0100)
- SCT Support Level: 1
- Device State: Active (0)
- Current Temperature: 21 Celsius
- Power Cycle Min/Max Temperature: 18/21 Celsius
- Lifetime Min/Max Temperature: 9/49 Celsius
- Lifetime Average Temperature: 31 Celsius
- Under/Over Temperature Limit Count: 0/0
- SCT Temperature History Version: 2
- Temperature Sampling Period: 1 minute
- Temperature Logging Interval: 1 minute
- Min/Max recommended Temperature: 0/60 Celsius
- Min/Max Temperature Limit: -40/65 Celsius
- Temperature History Size (Index): 128 (42)
- Index Estimated Time Temperature Celsius
- 43 2019-01-12 22:59 33 **************
- ... ..( 2 skipped). .. **************
- 46 2019-01-12 23:02 33 **************
- 47 2019-01-12 23:03 34 ***************
- 48 2019-01-12 23:04 33 **************
- ... ..( 2 skipped). .. **************
- 51 2019-01-12 23:07 33 **************
- 52 2019-01-12 23:08 34 ***************
- 53 2019-01-12 23:09 33 **************
- 54 2019-01-12 23:10 34 ***************
- ... ..( 4 skipped). .. ***************
- 59 2019-01-12 23:15 34 ***************
- 60 2019-01-12 23:16 ? -
- 61 2019-01-12 23:17 ? -
- 62 2019-01-12 23:18 ? -
- 63 2019-01-12 23:19 35 ****************
- 64 2019-01-12 23:20 36 *****************
- 65 2019-01-12 23:21 36 *****************
- 66 2019-01-12 23:22 37 ******************
- ... ..( 4 skipped). .. ******************
- 71 2019-01-12 23:27 37 ******************
- 72 2019-01-12 23:28 36 *****************
- 73 2019-01-12 23:29 36 *****************
- 74 2019-01-12 23:30 36 *****************
- 75 2019-01-12 23:31 ? -
- 76 2019-01-12 23:32 20 *
- 77 2019-01-12 23:33 22 ***
- 78 2019-01-12 23:34 23 ****
- 79 2019-01-12 23:35 24 *****
- 80 2019-01-12 23:36 25 ******
- 81 2019-01-12 23:37 27 ********
- 82 2019-01-12 23:38 27 ********
- 83 2019-01-12 23:39 27 ********
- 84 2019-01-12 23:40 28 *********
- 85 2019-01-12 23:41 28 *********
- 86 2019-01-12 23:42 ? -
- 87 2019-01-12 23:43 23 ****
- 88 2019-01-12 23:44 24 *****
- 89 2019-01-12 23:45 25 ******
- 90 2019-01-12 23:46 25 ******
- 91 2019-01-12 23:47 26 *******
- 92 2019-01-12 23:48 26 *******
- 93 2019-01-12 23:49 27 ********
- 94 2019-01-12 23:50 28 *********
- 95 2019-01-12 23:51 28 *********
- 96 2019-01-12 23:52 28 *********
- 97 2019-01-12 23:53 ? -
- 98 2019-01-12 23:54 32 *************
- ... ..( 5 skipped). .. *************
- 104 2019-01-13 00:00 32 *************
- 105 2019-01-13 00:01 33 **************
- ... ..( 5 skipped). .. **************
- 111 2019-01-13 00:07 33 **************
- 112 2019-01-13 00:08 34 ***************
- ... ..( 4 skipped). .. ***************
- 117 2019-01-13 00:13 34 ***************
- 118 2019-01-13 00:14 35 ****************
- 119 2019-01-13 00:15 35 ****************
- 120 2019-01-13 00:16 36 *****************
- 121 2019-01-13 00:17 36 *****************
- 122 2019-01-13 00:18 37 ******************
- 123 2019-01-13 00:19 36 *****************
- 124 2019-01-13 00:20 36 *****************
- 125 2019-01-13 00:21 36 *****************
- 126 2019-01-13 00:22 37 ******************
- ... ..( 2 skipped). .. ******************
- 1 2019-01-13 00:25 37 ******************
- 2 2019-01-13 00:26 38 *******************
- 3 2019-01-13 00:27 37 ******************
- 4 2019-01-13 00:28 ? -
- ... ..( 3 skipped). .. -
- 8 2019-01-13 00:32 ? -
- 9 2019-01-13 00:33 25 ******
- 10 2019-01-13 00:34 ? -
- 11 2019-01-13 00:35 27 ********
- 12 2019-01-13 00:36 27 ********
- 13 2019-01-13 00:37 28 *********
- ... ..( 2 skipped). .. *********
- 16 2019-01-13 00:40 28 *********
- 17 2019-01-13 00:41 29 **********
- ... ..( 2 skipped). .. **********
- 20 2019-01-13 00:44 29 **********
- 21 2019-01-13 00:45 ? -
- 22 2019-01-13 00:46 ? -
- 23 2019-01-13 00:47 21 **
- 24 2019-01-13 00:48 22 ***
- 25 2019-01-13 00:49 23 ****
- 26 2019-01-13 00:50 25 ******
- 27 2019-01-13 00:51 ? -
- 28 2019-01-13 00:52 ? -
- 29 2019-01-13 00:53 ? -
- 30 2019-01-13 00:54 26 *******
- 31 2019-01-13 00:55 ? -
- ... ..( 5 skipped). .. -
- 37 2019-01-13 01:01 ? -
- 38 2019-01-13 01:02 19 -
- 39 2019-01-13 01:03 20 *
- 40 2019-01-13 01:04 20 *
- 41 2019-01-13 01:05 21 **
- 42 2019-01-13 01:06 21 **
- SCT Error Recovery Control:
- Read: Disabled
- Write: Disabled
- Device Statistics (GP/SMART Log 0x04) not supported
- SATA Phy Event Counters (GP Log 0x11)
- ID Size Value Description
- 0x0001 2 0 Command failed due to ICRC error
- 0x0002 2 0 R_ERR response for data FIS
- 0x0003 2 0 R_ERR response for device-to-host data FIS
- 0x0004 2 0 R_ERR response for host-to-device data FIS
- 0x0005 2 0 R_ERR response for non-data FIS
- 0x0006 2 0 R_ERR response for device-to-host non-data FIS
- 0x0007 2 0 R_ERR response for host-to-device non-data FIS
- 0x0009 2 226 Transition from drive PhyRdy to drive PhyNRdy
- 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET
- 0x000b 2 0 CRC errors within host-to-device FIS
- 0x000d 2 0 Non-CRC errors within host-to-device FIS
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement