SHARE
TWEET

Untitled

a guest Aug 25th, 2019 352 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. # This file contains common pin mappings for the 2018 Creality
  2. # Ender 3. To use this config, the firmware should be compiled for the
  3. # AVR atmega1284p.
  4.  
  5. # Note, a number of Melzi boards are shipped with a bootloader that
  6. # requires the following command to flash the board:
  7. #  avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
  8. # If the above command does not work and "make flash" does not work
  9. # then one may need to flash a bootloader to the board - see the
  10. # Klipper docs/Bootloaders.md file for more information.
  11.  
  12. # See the example.cfg file for a description of available parameters.
  13.  
  14. [stepper_x]
  15. step_pin: PD7
  16. dir_pin: !PC5
  17. enable_pin: !PD6
  18. step_distance: .0125
  19. endstop_pin: ^PC2
  20. position_endstop: 0
  21. position_max: 235
  22. homing_speed: 50
  23.  
  24. [stepper_y]
  25. step_pin: PC6
  26. dir_pin: !PC7
  27. enable_pin: !PD6
  28. step_distance: .0125
  29. endstop_pin: ^PC3
  30. position_endstop: 0
  31. position_max: 235
  32. homing_speed: 50
  33.  
  34. [stepper_z]
  35. step_pin: PB3
  36. dir_pin: PB2
  37. enable_pin: !PA5
  38. step_distance: .0025
  39. endstop_pin:probe:z_virtual_endstop
  40. position_max: 250
  41. position_min: -1
  42.  
  43. [extruder]
  44. max_extrude_only_distance: 100.0
  45. step_pin: PB1
  46. dir_pin: !PB0
  47. enable_pin: !PD6
  48. step_distance: 0.010526
  49. nozzle_diameter: 0.400
  50. filament_diameter: 1.750
  51. pressure_advance: 0.060
  52. pressure_advance_lookahead_time: 0.010
  53. heater_pin: PD5
  54. sensor_type: EPCOS 100K B57560G104F
  55. sensor_pin: PA7
  56. #control: pid
  57. # tuned for stock hardware with 200 degree Celsius target
  58. #pid_Kp: 21.527
  59. #pid_Ki: 1.063
  60. #pid_Kd: 108.982
  61. min_temp: 0
  62. max_temp: 250
  63.  
  64. [heater_bed]
  65. heater_pin: PD4
  66. sensor_type: EPCOS 100K B57560G104F
  67. sensor_pin: PA6
  68. control: pid
  69. # tuned for stock hardware with 50 degree Celsius target
  70. pid_Kp: 54.027
  71. pid_Ki: 0.770
  72. pid_Kd: 948.182
  73. min_temp: 0
  74. max_temp: 130
  75.  
  76. [fan]
  77. pin: PB4
  78.  
  79. [mcu]
  80. serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06SCF6-if00-port0
  81.  
  82. [printer]
  83. kinematics: cartesian
  84. max_velocity: 300
  85. max_accel: 3000
  86. max_z_velocity: 5
  87. max_z_accel: 100
  88.  
  89. [display]
  90. lcd_type: st7920
  91. cs_pin: PA3
  92. sclk_pin: PA1
  93. sid_pin: PC1
  94. encoder_pins: ^PD2, ^PD3
  95. click_pin: ^!PC0
  96.  
  97. [bltouch]
  98. sensor_pin: ^PC4
  99. control_pin: PA4
  100. x_offset: -45
  101. y_offset: -10
  102. z_offset: 1.6
  103. pin_move_time: 0.4
  104.  
  105. [bed_mesh]
  106. speed: 80
  107. horizontal_move_z: 5
  108. min_point: 90, 20
  109. max_point: 235, 235
  110. probe_count: 3,3
  111. fade_start: 1.0
  112. mesh_pps: 2,2
  113.  
  114. [gcode_macro G29]
  115. gcode:
  116.     BED_MESH_CALIBRATE
  117.  
  118. [safe_z_home]
  119. home_xy_position: 155,120
  120. speed: 80.0
  121. z_hop: 10.0
  122. z_hop_speed: 10.0
  123.  
  124.  
  125. #*# <---------------------- SAVE_CONFIG ---------------------->
  126. #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
  127. #*#
  128. #*# [extruder]
  129. #*# control = pid
  130. #*# pid_kp = 30.662
  131. #*# pid_ki = 2.350
  132. #*# pid_kd = 100.035
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top