SHARE
TWEET

Untitled

a guest Feb 13th, 2017 2,279 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. [    7.143377@3] usb 1-1.1: New device HCW 955D @ 480 Mbps (2040:026d, interface 0, class 0)
  2. [    7.143390@3] usb 1-1.1: DVB interface 0 found: isoc
  3. [    7.143550@0] usb 1-1.1: em28174#0: chip ID is em28174
  4. [    7.164813@2] Bluetooth: Core ver 2.18
  5. [    7.165374@2] NET: Registered protocol family 31
  6. [    7.165383@2] Bluetooth: HCI device and connection manager initialized
  7. [    7.165408@2] Bluetooth: HCI socket layer initialized
  8. [    7.165414@2] Bluetooth: L2CAP socket layer initialized
  9. [    7.165437@2] Bluetooth: SCO socket layer initialized
  10. [    7.166683@2] Bluetooth: Generic Bluetooth SDIO driver ver 0.1
  11. [    7.183464@2] cfg80211: Calling CRDA to update world regulatory domain
  12. [    7.190345@2] Console: switching to colour dummy device 80x25
  13. [    7.206926@2] remote: cur_mode = 0
  14. [    7.206944@2] remote: set_remote_mode[74]
  15. [    7.378505@0] dhd_module_init: in
  16. [    7.378532@0] ======== bcm_wlan_set_plat_data ========
  17. [    7.378540@0] host_oob_irq: 100
  18. [    7.378544@0] host_oob_irq_flags=0x414
  19. [    7.378548@0] dhd_wifi_platform_load: Enter
  20. [    7.378583@0] Power-up adapter 'DHD generic adapter'
  21. [    7.378587@0] wifi_platform_set_power = 1
  22. [    7.378590@0] ======== PULL WL_REG_ON HIGH! ========
  23. [    7.378616@0] aml_wifi wifi.30: [extern_wifi_set_enable] WIFI  Disable! 238
  24. [    7.578659@0] aml_wifi wifi.30: [extern_wifi_set_enable] WIFI  Enable! 238
  25. [    8.071882@1] FAT-fs (sda): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
  26. [    8.081494@0] wifi_platform_bus_enumerate device present 1
  27. [    8.081509@0] ======== Card detection to detect SDIO card! ========
  28. [    8.081512@0] sdio_reset_comm():
  29. [    8.172107@2] 8021q: 802.1Q VLAN Support v1.8
  30. [    8.229667@0] usb 1-1.1: em28174#0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x547901ca
  31. [    8.229678@0] usb 1-1.1: em28174#0: EEPROM info:
  32. [    8.229683@0] usb 1-1.1: em28174#0:  microcode start address = 0x0004, boot configuration = 0x01
  33. [    8.237042@0] usb 1-1.1: em28174#0:  AC97 audio (5 sample rates)
  34. [    8.237053@0] usb 1-1.1: em28174#0:  500mA max power
  35. [    8.237059@0] usb 1-1.1: em28174#0:  Table at offset 0x27, strings=0x0a72, 0x187c, 0x086a
  36. [    8.241957@3] usb 1-1.1: em28174#0: Identified as Hauppauge WinTV-dualHD ATSC (card=100)
  37. [    8.244900@3] tveeprom: Hauppauge model 204101, rev B2I6, serial# 11511331
  38. [    8.244912@3] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
  39. [    8.244917@3] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
  40. [    8.244921@3] tveeprom: audio processor is None (idx 0)
  41. [    8.244924@3] tveeprom: has no radio, has IR receiver, has no IR transmitter
  42. [    8.244936@3] usb 1-1.1: em28174#0: dvb set to isoc mode.
  43. [    8.245064@3] usb 1-1.1: em28174#1: chip ID is em28174
  44. [    9.208969@0] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
  45. [    9.213782@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
  46. [    9.216313@0] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
  47. [    9.309227@0] sdio: clk 200000000 SDR mode tuning start
  48. [    9.309403@0] sdio: rx_tuning_result[0] = 10
  49. [    9.309574@0] sdio: rx_tuning_result[1] = 10
  50. [    9.309757@0] sdio: rx_tuning_result[3] = 10
  51. [    9.309935@0] sdio: rx_tuning_result[4] = 10
  52. [    9.309942@0] sdio: best_win_start =3, best_win_size =4
  53. [    9.309947@0] sdio: sd_emmc_regs->gclock=0x1000245,sd_emmc_regs->gadjust=0x2000
  54. [    9.309955@0] sdio: gclock =0x1000245, gdelay=0x0, gadjust=0x2000
  55. [    9.309961@0] [sdio_reinit] finish
  56. [    9.327557@0] bcmsdh_register: register client driver
  57. [    9.327686@0] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
  58. [    9.327747@0] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
  59. [    9.327753@0] bus num (host idx)=0, slot num (rca)=1
  60. [    9.327758@0] found adapter info 'DHD generic adapter'
  61. [    9.327831@0] sdioh_attach: set sd_f2_blocksize 128
  62. [    9.328070@0] dhdsdio_probe : no mutex held. set lock
  63. [    9.328158@0] F1 signature read @0x18000000=0x16014335
  64. [    9.329458@3] usb 1-1.1: em28174#1: EEPROM ID = 26 00 01 00, EEPROM hash = 0x547901ca
  65. [    9.329467@3] usb 1-1.1: em28174#1: EEPROM info:
  66. [    9.329475@3] usb 1-1.1: em28174#1:  microcode start address = 0x0004, boot configuration = 0x01
  67. [    9.330821@0] F1 signature OK, socitype:0x1 chip:0x4335 rev:0x1 pkg:0x0
  68. [    9.331211@0] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000
  69. [    9.331286@0] dhd_conf_set_chiprev: chip=0x4335, chiprev=1
  70. [    9.331339@0] dhd_conf_set_conf_path_by_nv_path: config_path=/usr/lib/firmware/brcm/config.txt
  71. [    9.337578@0] usb 1-1.1: em28174#1:  AC97 audio (5 sample rates)
  72. [    9.337591@0] usb 1-1.1: em28174#1:  500mA max power
  73. [    9.337600@0] usb 1-1.1: em28174#1:  Table at offset 0x27, strings=0x0a72, 0x187c, 0x086a
  74. [    9.338596@3] usb 1-1.1: em28174#1: Identified as Hauppauge WinTV-dualHD ATSC (card=100)
  75. [    9.340487@0] dhd_conf_read_nv_by_chip: nv_by_chip_count=9
  76. [    9.340503@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=0, name=nvram_ap6181.txt
  77. [    9.340510@0] dhd_conf_read_nv_by_chip: chip=0xa962, chiprev=1, name=nvram_ap6210.txt
  78. [    9.340516@0] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=0, name=nvram_ap6212.txt
  79. [    9.340522@0] dhd_conf_read_nv_by_chip: chip=0xa9a6, chiprev=1, name=nvram_ap6212a.txt
  80. [    9.340528@0] dhd_conf_read_nv_by_chip: chip=0x4345, chiprev=6, name=nvram_ap6255.txt
  81. [    9.340540@0] dhd_conf_read_nv_by_chip: chip=0x4330, chiprev=4, name=nvram_ap6330.txt
  82. [    9.340546@0] dhd_conf_read_nv_by_chip: chip=0x4339, chiprev=1, name=nvram_ap6335.txt
  83. [    9.340552@0] dhd_conf_read_nv_by_chip: chip=0x4356, chiprev=2, name=nvram_ap6356.txt
  84. [    9.340558@0] dhd_conf_read_nv_by_chip: chip=0x4335, chiprev=1, name=nvram_bcm4335.txt
  85. [    9.340636@0] dhd_conf_read_config: mimo_bw_cap = 1
  86. [    9.340987@0] dhd_conf_read_config: bcn_timeout = 20
  87. [    9.341074@0] dhd_conf_read_config: kso_enable = 0
  88. [    9.341390@0] dhd_conf_read_config: PM = 0
  89. [    9.342391@3] tveeprom: Hauppauge model 204101, rev B2I6, serial# 11511331
  90. [    9.342405@3] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
  91. [    9.342413@3] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
  92. [    9.342426@3] tveeprom: audio processor is None (idx 0)
  93. [    9.342431@3] tveeprom: has no radio, has IR receiver, has no IR transmitter
  94. [    9.342445@3] usb 1-1.1: em28174#1: dvb ts2 set to isoc mode.
  95. [    9.352410@0] wl_create_event_handler(): thread:wl_event_handler:ade started
  96. [    9.352794@1] tsk Enter, tsk = 0xffffff8003fdf940
  97. [    9.353187@0] dhd_attach(): thread:dhd_watchdog_thread:ae0 started
  98. [    9.353225@0] dhd_attach(): thread:dhd_dpc:ae1 started
  99. [    9.353257@0] dhd_dpc_thread: set dpc_cpucore 0 from config.txt
  100. [    9.353266@0] dhd_attach(): thread:dhd_rxf:ae2 started
  101. [    9.353283@0] dhd_deferred_work_init: work queue initialized
  102. [    9.359434@0] Dongle Host Driver, version 1.201.59.6 (r506368)
  103. [    9.359434@0] Compiled in drivers/net/wireless/bcmdhd
  104. [    9.360512@0] Register interface [wlan0]  MAC: 40:f3:08:68:20:a4
  105. [    9.360512@0]
  106. [    9.360521@0] dhd_prot_ioctl : bus is down. we have nothing to do
  107. [    9.361182@0] dhd_open: Enter ffffffc026266000
  108. [    9.361190@0] dhd_open : dhd_open: call dev open before insmod complete!
  109. [    9.361212@0] bcmsdh_oob_intr_unregister: Enter
  110. [    9.361216@0] bcmsdh_oob_intr_unregister: irq is not registered
  111. [    9.361225@0] dhd_txglom_enable: enable 0
  112. [    9.361229@0] dhd_conf_set_txglom_params: swtxglom=0, txglom_ext=0
  113. [    9.361233@0] dhd_conf_set_txglom_params: txglom_bucket_size=0
  114. [    9.361237@0] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0, bus_txglom=0
  115. [    9.361241@0] dhd_conf_set_txglom_params: tx_in_rx=1, tx_max_offset=0
  116. [    9.361244@0] dhd_bus_devreset:  WLAN OFF DONE
  117. [    9.361301@0] wifi_platform_set_power = 0
  118. [    9.361305@0] ======== PULL WL_REG_ON LOW! ========
  119. [    9.361312@0] dhdsdio_probe : the lock is released.
  120. [    9.361741@0]
  121. [    9.361741@0] Dongle Host Driver, version 1.201.59.6 (r506368)
  122. [    9.361741@0] Compiled in drivers/net/wireless/bcmdhd
  123. [    9.361753@0] wl_android_wifi_on in 1
  124. [    9.361757@0] wl_android_wifi_on in 2: g_wifi_on=0
  125. [    9.361761@0] wifi_platform_set_power = 1
  126. [    9.361765@0] ======== PULL WL_REG_ON HIGH! ========
  127. [    9.361785@0] aml_wifi wifi.30: [extern_wifi_set_enable] WIFI  Disable! 238
  128. [    9.371495@2] dhd_module_init: Exit err=0
  129. [    9.545275@3] usbcore: registered new interface driver em28xx
  130. [    9.550558@2] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 0 to 9600
  131. [    9.550606@2] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 9600 to 9600
  132. [    9.550626@2] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 9600 to 115200
  133. [    9.558500@1] WARNING: You are using an experimental version of the media stack.
  134. [    9.558500@1]        As the driver is backported to an older kernel, it doesn't offer
  135. [    9.558500@1]        enough quality for its usage in production.
  136. [    9.558500@1]        Use it with care.
  137. [    9.558500@1] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
  138. [    9.558500@1]        a02ff2e02bee64e9955dbfd8811874c3f3880f58 cx231xx: Fix TBS MAC reading.
  139. [    9.560374@1] usb 1-1.1: em28174#1: Registering input extension
  140. [    9.561868@0] aml_wifi wifi.30: [extern_wifi_set_enable] WIFI  Enable! 238
  141. [    9.591455@1] Registered IR keymap rc-hauppauge
  142. [    9.591860@1] input: 1-1.1: em28174#1 IR as /devices/dwc2_b/usb1/1-1/1-1.1: em28174#1/rc/rc0/input4
  143. [    9.592551@1] rc rc0: 1-1.1: em28174#1 IR as /devices/dwc2_b/usb1/1-1/1-1.1: em28174#1/rc/rc0
  144. [    9.592881@1] usb 1-1.1: em28174#1: Input extension successfully initalized
  145. [    9.592888@1] usb 1-1.1: em28174#1: Registering input extension
  146. [    9.593256@1] Registered IR keymap rc-hauppauge
  147. [    9.596892@2] ir-keytable[2816]: unhandled level 3 translation fault (11) at 0x00000000, esr 0x92000007
  148. [    9.596902@2] pgd = ffffffc026b7c000
  149. [    9.596906@2] [00000000] *pgd=0000000026b79003, *pmd=0000000026b7d003, *pte=0000000000000000
  150. [    9.596911@2]
  151. [    9.596918@2] CPU: 2 PID: 2816 Comm: ir-keytable Tainted: G           O 3.14.29 #1
  152. [    9.596923@2] task: ffffffc024a72a80 ti: ffffffc027b34000 task.ti: ffffffc027b34000
  153. [    9.596937@2] PC is at 0xa488
  154. [    9.596941@2] LR is at 0xa710
  155. [    9.596944@2] pc : [<000000000000a488>] lr : [<000000000000a710>] pstate: 60000010
  156. [    9.596947@2] sp : 00000000ffd2a660
  157. [    9.596950@2] x12: 0000000000000000
  158. [    9.596953@2] x11: 0000000000000000 x10: 00000000f73aafb4
  159. [    9.596957@2] x9 : 0000000000000000 x8 : 0000000000000000
  160. [    9.596961@2] x7 : 00000000000114e8 x6 : 0000000000000000
  161. [    9.596965@2] x5 : 0000000000011494 x4 : 0000000000000000
  162. [    9.596969@2] x3 : 0000000000000000 x2 : 0000000000000000
  163. [    9.596973@2] x1 : 0000000000000000 x0 : 0000000000000000
  164. [    9.596976@2]
  165. [    9.597223@3] input: 1-1.1: em28174#1 IR as /devices/dwc2_b/usb1/1-1/1-1.1: em28174#1/rc/rc1/input5
  166. [    9.597869@3] rc rc1: 1-1.1: em28174#1 IR as /devices/dwc2_b/usb1/1-1/1-1.1: em28174#1/rc/rc1
  167. [    9.598259@3] usb 1-1.1: em28174#1: Input extension successfully initalized
  168. [    9.598265@3] em28xx: Registered (Em28xx Input Extension) extension
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
Top