[2018-09-08 13:05:28] [Output] : * Jared Lyall puts the key in the door to unlock it. *
[2018-09-08 13:05:29] [Output] : * Jared Lyall puts the key in the door to lock it. *
[2018-09-08 13:07:57] [Output] : ★ Jared Lyall enters the Caddy, he removes a cover and presses a button, opening the hood.
[2018-09-08 13:08:02] [Output] : ★ Jared Lyall presses another button to open up the trunk.
[2018-09-08 13:08:14] [Output] : ★ Jared Lyall heads out of the Caddy, he walks to the front of the car.
[2018-09-08 13:08:22] [Output] : ★ Jared Lyall raises the hood and hoists it properly so that it does not fall.
[2018-09-08 13:08:36] [Output] : ★ Jared Lyall reaches for a box and places it next to the vehicle. It contains -
[2018-09-08 13:08:42] [Output] : ★ - various bolts, ratchets, et cetera.      ((Jared Lyall))
[2018-09-08 13:08:59] [Output] : ★ Jared Lyall inspects the Cadillac's battery for a couple of seconds.
[2018-09-08 13:09:19] [Output] : ★ Jared Lyall reaches for a wrench, he starts unbolting the battery's positive terminal.
[2018-09-08 13:09:24] [Output] : ★ Jared Lyall removes the bolt.
[2018-09-08 13:09:32] [Output] : ★ Jared Lyall removes the battery's positive terminal cable.
[2018-09-08 13:09:42] [Output] : ★ Jared Lyall starts unbolting the battery's negative terminal after removing a plastic cover -
[2018-09-08 13:09:51] [Output] : ★ - that has been covering it. He'd have removed the same cover from the positive -      ((Jared Lyall))
[2018-09-08 13:09:56] [Output] : ★ - terminal as well.      ((Jared Lyall))
[2018-09-08 13:10:08] [Output] : ★ Jared Lyall removes the bolt.
[2018-09-08 13:10:21] [Output] : ★ Jared Lyall disconnects the negative terminal's cable.
[2018-09-08 13:10:29] [Output] : ★ Jared Lyall starts unscrewing a small stand that holds the battery in place.
[2018-09-08 13:10:35] [Output] : ★ Jared Lyall ensures no other bolts or screws are holding the battery.
[2018-09-08 13:10:59] [Output] : ★ Jared Lyall removes the battery from the vehicle and places it onto the shelf, in a box.
[2018-09-08 13:12:15] [Output] : ★ Jared Lyall reaches for a hydraulic jack, he places it near the front wheel as not to damage the -
[2018-09-08 13:12:27] [Output] : ★ - axle, but giving enough leeway for him to remove the wheel.      ((Jared Lyall))
[2018-09-08 13:12:36] [Output] : ★ Jared Lyall removes the clippings holding the rim onto the wheel.
[2018-09-08 13:13:11] [Output] : ★ Jared Lyall reaches for a tire iron. He starts removing the nuts holding the wheel into position.
[2018-09-08 13:13:20] [Output] : ★ Jared Lyall slowly pulls off the wheel and leans it against the shelf.
[2018-09-08 13:13:36] [Output] : ★ Jared Lyall reaches for another hydro-jack. He places this one near the left rear wheel.
[2018-09-08 13:13:43] [Output] : ★ Jared Lyall removes the clipping holding the rim into position.
[2018-09-08 13:13:47] [Output] : ★ Jared Lyall removes the nuts using the tire iron.
[2018-09-08 13:13:51] [Output] : ★ Jared Lyall removes the wheel afterwards.
[2018-09-08 13:14:22] [Output] : ★ Jared Lyall reaches for a third hydro-jack. Jared makes sure the vehicle is well supported on the lift -
[2018-09-08 13:14:30] [Output] : ★ - as well. He places this one near the right rear wheel.      ((Jared Lyall))
[2018-09-08 13:14:34] [Output] : ★ Jared Lyall removes the clippings from the rim
[2018-09-08 13:14:37] [Output] : ★ Jared Lyall removes the nuts from the wheel.
[2018-09-08 13:14:40] [Output] : ★ Jared Lyall removes the third wheel.
[2018-09-08 13:14:45] [Output] : ADVERT: Selling '69 Chevelle COPO 427 - 170 km/h , low mileage. $165,000  | #373459
[2018-09-08 13:14:47] [Output] : ★ Jared Lyall repeats the process with the final wheel.
[2018-09-08 13:14:59] [Output] : ★ Jared Lyall places all rims into a box, and places the wheels against the wall.
[2018-09-08 13:15:40] [Output] : ★ Jared Lyall reaches for the hood once more, he lowers it a bit, using his own hands to support it.
[2018-09-08 13:15:54] [Output] : ★ Jared Lyall starts unscrewing two 16mm bolts from each side of the hood using a ratchet.
[2018-09-08 13:16:23] [Output] : ★ Jared Lyall reaches for a pair of wire cutters, and cuts off two tyraps that hold the hood into -
[2018-09-08 13:16:25] [Output] : ★ - position.      ((Jared Lyall))
[2018-09-08 13:16:32] [Output] : ★ Jared Lyall removes three clips holding the hood in place.
[2018-09-08 13:16:58] [Output] : ★ Jared Lyall prys out a plug near the fender to the side, as to prevent it from -
[2018-09-08 13:17:00] [Output] : ★ - holding the hood.      ((Jared Lyall))
[2018-09-08 13:17:23] [Output] : ★ Jared Lyall loosens up two more bolts from the hood, but does not remove them entirely.
[2018-09-08 13:17:29] [Output] : ★ Jared Lyall does that using the socket and ratchet.
[2018-09-08 13:17:46] [Output] : ★ Jared Lyall reaches for a hammer. He lowers the hood once more. This time, he starts -
[2018-09-08 13:18:03] [Output] : ★ - popping out the left sided bolt. He reaches for a cushion and places it under the hood as      ((Jared Lyall))
[2018-09-08 13:18:07] [Output] : ★ - to provide support.      ((Jared Lyall))
[2018-09-08 13:18:21] [Output] : ★ Jared Lyall walks to the other side of the vehicle, he keeps holding the hood as he walks.
[2018-09-08 13:18:35] [Output] : ★ Jared Lyall reaches for another cushion, he pops the second bolt and places the cushion under it.
[2018-09-08 13:19:15] [Output] : Jared Lyall: (( ew. he pops the PINS, not the bolts! ))
[2018-09-08 13:19:32] [Output] : ★ Jared Lyall reaches for the socket and ratchet. He starts unscrewing the loosened pins entirely.
[2018-09-08 13:19:36] [Output] : ★ Jared Lyall does that for both sides.
[2018-09-08 13:20:00] [Output] : ★ Jared Lyall places all bolts onto the shelf.
[2018-09-08 13:20:11] [Output] : ★ Jared Lyall reaches for a hood, getting a firm grasp on it.
[2018-09-08 13:20:17] [Output] : ★ Jared Lyall slowly raises the hood.
[2018-09-08 13:20:21] [Output] : ★ Jared Lyall leans up the hood against the wall.
[2018-09-08 13:20:51] [Output] : ★ Jared Lyall disconnects the screws connecting the intake manifold to the engine using a screw-
[2018-09-08 13:20:54] [Output] : ★ -driver.      ((Jared Lyall))
[2018-09-08 13:21:07] [Output] : ★ Jared Lyall disconnects screws from a hose connected to the engine.
[2018-09-08 13:21:32] [Output] : ★ Jared Lyall removes the cap on the low pressure charging point by turning it -
[2018-09-08 13:21:35] [Output] : ★ - counter clockwise.      ((Jared Lyall))
[2018-09-08 13:21:52] [Output] : ★ Jared Lyall removes the cowl panel cover from the front side of the vehicle.
[2018-09-08 13:21:57] [Output] : ★ Jared Lyall raises the lift halfway.
[2018-09-08 13:22:11] [Output] : ★ Jared Lyall looks at the vehicle, making sure there's enough room for him to walk under the vehicle.
[2018-09-08 13:22:20] [Output] : ★ Jared Lyall raises the lift up a bit more.
[2018-09-08 13:22:35] [Output] : ★ Jared Lyall reaches for the socket and ratchet, then walks under the vehicle.
[2018-09-08 13:22:42] [Output] : ★ Jared Lyall sets his eyes on the control arm.
[2018-09-08 13:22:59] [Output] : ★ Jared Lyall loosens the bolts on the tuning fork using an 18mm ratchet.
[2018-09-08 13:23:03] [Output] : ★ Jared Lyall does not remove the bolts.
[2018-09-08 13:23:14] [Output] : ★ Jared Lyall loosens the bolt on top of the balljoint.
[2018-09-08 13:23:31] [Output] : ★ Jared Lyall loosens a third bolt that is near the tuning fork, on the bumper's side.
[2018-09-08 13:23:47] [Output] : ★ Jared Lyall reaches for the bolt on the tuning fork, he starts unscrewing it with his hand, and -
[2018-09-08 13:23:53] [Output] : ★ - pulls the bolt through.      ((Jared Lyall))
[2018-09-08 13:24:13] [Output] : ★ Jared Lyall places some PT Blaster on the ball joint shaft; coaxing it out.
[2018-09-08 13:24:24] [Output] : ★ Jared Lyall unbolts two 10mm bolts using the ratchet.
[2018-09-08 13:24:38] [Output] : ★ The bolts are near the lower link.      ((Jared Lyall))
[2018-09-08 13:24:42] [Output] : ★ Jared Lyall grabs a hammer.
[2018-09-08 13:24:59] [Output] : ★ Jared Lyall puts the ball joint's nut back on its bolt.
[2018-09-08 13:25:03] [Output] : ★ Jared Lyall places an extension onto the nut.
[2018-09-08 13:25:15] [Output] : ★ Jared Lyall slowly but firmly hits the extension with the hammer.
[2018-09-08 13:25:28] [Output] : ★ This forces the ball joint to loosen up.      ((Jared Lyall))
[2018-09-08 13:25:38] [Output] : ★ Jared Lyall keeps the nut on the bolt for the disc's safety.
[2018-09-08 13:25:49] [Output] : ★ Jared Lyall unpins the bolt on top using his hand, the pre-loosened bolt.
[2018-09-08 13:26:08] [Output] : ★ Jared Lyall slowly pulls out the ball joint.
[2018-09-08 13:26:25] [Output] : ★ Jared Lyall holds the ball joint in place, removing the nut. The ball joint would have moved along -
[2018-09-08 13:26:28] [Output] : ★ - as Jared pulled it.      ((Jared Lyall))
[2018-09-08 13:26:40] [Output] : ★ Jared Lyall wiggles the ball joint a bit, then removes it entirely.
[2018-09-08 13:26:46] [Output] : ★ Jared Lyall then removes the control arm.
[2018-09-08 13:26:53] [Output] : ★ Jared Lyall places the control arm onto the shelf.
[2018-09-08 13:27:02] [Output] : ★ Jared Lyall removes the lid at the back of the cowl.
[2018-09-08 13:28:28] [Output] : ★ Jared Lyall lowers the vehicle once more.
[2018-09-08 13:28:49] [Output] : ★ Jared Lyall unscrews the bolts holding the frontlights in place.
[2018-09-08 13:28:55] [Output] : ★ Jared Lyall removes the frontlights, placing them into a box on the shelf.
[2018-09-08 13:29:18] [Output] : ★ The bolts would be on the top side of the frontlights, near the engine bay.      ((Jared Lyall))
[2018-09-08 13:29:21] [Output] : ★ Jared Lyall raises the vehicle once more.
[2018-09-08 13:29:34] [Output] : ★ Jared Lyall reaches under the vehicle with a screwgun.
[2018-09-08 13:29:42] [Output] : ★ Jared Lyall attaches a 16mm head to the screwgun.
[2018-09-08 13:29:52] [Output] : ★ Jared Lyall unscrews four heads, under the right splash panel.
[2018-09-08 13:30:00] [Output] : ★ Jared Lyall looks around a bit, inspecting the current status of the vehicle.
[2018-09-08 13:30:15] [Output] : ★ Jared Lyall removes the one holding the splash panel from under the bumper.
[2018-09-08 13:30:21] [Output] : ★ Jared Lyall removes the clips on the splash panel.
[2018-09-08 13:30:24] [Output] : ★ Jared Lyall removes the splash panel.
[2018-09-08 13:30:37] [Output] : ★ Jared Lyall unscrews another four bolts from the other splash panel.
[2018-09-08 13:30:43] [Output] : ★ Jared Lyall removes the bolts.
[2018-09-08 13:30:49] [Output] : ★ Jared Lyall pulls out the second splash panel
[2018-09-08 13:31:02] [Output] : ★ Jared Lyall places both splash panels in a box, on the shelf.
[2018-09-08 13:31:28] [Output] : ★ Jared Lyall removes five bolts from the bumper back - near the wheels.
[2018-09-08 13:31:40] [Output] : ★ Jared Lyall peels the wheel well liner back, unscrewing a fifth bolt.
[2018-09-08 13:31:48] [Output] : ★ Jared Lyall places all bolts into a box, on the shelf.
[2018-09-08 13:31:56] [Output] : ★ Jared Lyall reaches for the other wheel.
[2018-09-08 13:32:01] [Output] : ★ Jared Lyall removes another four bolts from the bumper back.
[2018-09-08 13:32:11] [Output] : ★ Jared Lyall peels back the same wheel well liner (on the other side), and unscrews -
[2018-09-08 13:32:13] [Output] : ★ - the final bolt.      ((Jared Lyall))
[2018-09-08 13:32:32] [Output] : ★ Jared Lyall unclips the top of the bumper, close to the wires on both sides.
[2018-09-08 13:32:40] [Output] : ★ Jared Lyall places an 8mm head onto the gun.
[2018-09-08 13:32:52] [Output] : ★ Jared Lyall inspects the vehicle again, looking for the bolts in question.
[2018-09-08 13:33:28] [Output] : ★ Jared Lyall removes eight 8mm bolts from under the bumper.
[2018-09-08 13:33:39] [Output] : ★ Jared Lyall moves from underneath the car.
[2018-09-08 13:33:40] [Output] : ★ Jared Lyall lowers the car.
[2018-09-08 13:33:52] [Output] : ★ Jared Lyall removes the weatherstripping from the top of the hood, simply by pulling it up.
[2018-09-08 13:33:54] [Output] : ★ Jared Lyall places it onto the shelf.
[2018-09-08 13:34:16] [Output] : ★ Jared Lyall removes 3 t45 screws on both ends, and 5 t30 bolts in the middle.
[2018-09-08 13:34:28] [Output] : ★ Jared Lyall disconnects the temp sensor.
[2018-09-08 13:34:34] [Output] : ★ Jared Lyall removes two horn connectors.
[2018-09-08 13:34:52] [Output] : ★ Jared Lyall removes the bumper now, properly. There'd be nothing holding it in place anymore.
[2018-09-08 13:34:58] [Output] : ★ Jared Lyall places the bumper into a large box, on the floor.
[2018-09-08 13:35:22] [Output] : ★ Jared Lyall removes two bolts from underneath both headlights.
[2018-09-08 13:35:36] [Output] : ★ Jared Lyall would have done that as he removed the headlights, since they also -
[2018-09-08 13:35:38] [Output] : ★ - hold them in place.      ((Jared Lyall))
[2018-09-08 13:35:48] [Output] : ★ Jared Lyall disconnects the push-lock connectors.
[2018-09-08 13:35:55] [Output] : ★ Four per headlight.      ((Jared Lyall))
[2018-09-08 13:35:58] [Output] : ★ One per sidelight.      ((Jared Lyall))
[2018-09-08 13:36:11] [Output] : ★ Jared Lyall unscrews a t25 behind the radiator.
[2018-09-08 13:36:19] [Output] : ★ Jared Lyall pulls up the radiator, placing it into a box.
[2018-09-08 13:36:32] [Output] : ★ Jared Lyall ensures the radiator is not spilling, if it is, then he'd place it on a piece of cloth first
[2018-09-08 13:36:47] [Output] : ★ Jared Lyall reaches for two locking wires.
[2018-09-08 13:36:51] [Output] : ★ Jared Lyall pulls them towards him.
[2018-09-08 13:37:00] [Output] : ★ Jared Lyall pushes them off afterwards.
[2018-09-08 13:37:03] [Output] : ★ The wires start draining.      ((Jared Lyall))
[2018-09-08 13:37:19] [Output] : ★ Jared Lyall unhooks the lines from the condenser, by removing 6mm allens.
[2018-09-08 13:37:29] [Output] : ★ Jared Lyall disconnects one of the lines from the top of the condenser.
[2018-09-08 13:37:36] [Output] : ★ Jared Lyall places this line on the shelf.
[2018-09-08 13:37:41] [Output] : ★ Jared Lyall disconnects the other line from the dryer.
[2018-09-08 13:37:47] [Output] : ★ Jared Lyall places it next to the other line.
[2018-09-08 13:37:59] [Output] : ★ Jared Lyall removes the receiver dryer line from its place.
[2018-09-08 13:38:06] [Output] : ★ Jared Lyall places it next to the two other lines.
[2018-09-08 13:38:22] [Output] : ★ Jared Lyall removes the electronic connector's front.
[2018-09-08 13:38:31] [Output] : ★ Jared Lyall removes 3 bolts holding the compressor.
[2018-09-08 13:38:40] [Output] : ★ The top one is left in, but loosened.      ((Jared Lyall))
[2018-09-08 13:38:47] [Output] : ★ This holds the AC compressor in place.      ((Jared Lyall))
[2018-09-08 13:38:56] [Output] : ★ Jared Lyall wiggles the compressor around a bit.
[2018-09-08 13:39:09] [Output] : ★ Jared Lyall removes the bolt then carefully removes the AC compressor.
[2018-09-08 13:39:14] [Output] : ★ Jared Lyall places it onto a piece of cloth as to let it drain.
[2018-09-08 13:39:33] [Output] : ★ Jared Lyall pops a plastic rivet.
[2018-09-08 13:39:42] [Output] : ★ Jared Lyall unbolts a t25 from the other side of the engine bay.
[2018-09-08 13:39:48] [Output] : ★ Jared Lyall removes the AC condenser.
[2018-09-08 13:39:52] [Output] : ★ Jared Lyall places it onto the shelf, in a box.
[2018-09-08 13:40:11] [Output] : ★ This is done after removing four bolts from the top part of the engine bay;      ((Jared Lyall))
[2018-09-08 13:40:19] [Output] : ★ they held the condenser.      ((Jared Lyall))
[2018-09-08 13:40:45] [Output] : ★ Jared Lyall removes two screws from the top part.
[2018-09-08 13:40:52] [Output] : ★ Jared Lyall removes a cable from the top part.
[2018-09-08 13:41:11] [Output] : ★ Jared Lyall removes 4 12mm bolts and the washers attached to them.
[2018-09-08 13:41:16] [Output] : ★ Jared Lyall removes the front guard.
[2018-09-08 13:41:28] [Output] : ★ Jared Lyall unbolts the air ducts; held by 3 8mm bolts.
[2018-09-08 13:41:32] [Output] : ★ Jared Lyall removes the air ducts.
[2018-09-08 13:41:45] [Output] : ★ Jared Lyall pulls out the power steering pump.
[2018-09-08 13:41:49] [Output] : ★ Jared Lyall disconnects the reservoir lines.
[2018-09-08 13:41:53] [Output] : ★ Jared Lyall removes the transmission mount.
[2018-09-08 13:41:59] [Output] : ★ Jared Lyall disconnects the ATF cooler lines.
[2018-09-08 13:42:10] [Output] : ★ Jared Lyall disconnects the drive shaft afterwards.
[2018-09-08 13:42:18] [Output] : ★ Jared Lyall removes most of the bolts from the bottom of the bell housing.
[2018-09-08 13:42:31] [Output] : ★ There'd be five bolts holding the engine in place.      ((Jared Lyall))
[2018-09-08 13:42:48] [Output] : ★ Jared Lyall pulls the engine forward a bit, giving himself some space to remove the bolts -
[2018-09-08 13:42:53] [Output] : ★ - on the opposite side of the engine.      ((Jared Lyall))
[2018-09-08 13:43:01] [Output] : ★ Jared Lyall reaches for a ratchet with an e14.
[2018-09-08 13:43:15] [Output] : ★ Jared Lyall removes the bolt on the back of the engine.
[2018-09-08 13:43:24] [Output] : ★ Jared Lyall removes another bolt next to it using an 11mm wrench.
[2018-09-08 13:43:34] [Output] : ★ Jared Lyall slides the engine to the left carefully.
[2018-09-08 13:43:43] [Output] : ★ Jared Lyall removes a bolt from the back-right side of the engine.
[2018-09-08 13:43:49] [Output] : ((OOC Luck)) Jared Lyall tries their luck from 1 to 100 and gets 62.
[2018-09-08 13:43:50] [Output] : ((OOC Chance at 62%)) Jared Lyall's attempt has failed.
[2018-09-08 13:43:59] [Output] : ★ Jared Lyall is unable to the remove the bolt without an extension.
[2018-09-08 13:44:09] [Output] : ★ Jared Lyall reaches for an extension, placing it onto the bolt, and starts removing the bolt.
[2018-09-08 13:44:10] [Output] : ((OOC Luck)) Jared Lyall tries their luck from 1 to 130 and gets 50.
[2018-09-08 13:44:12] [Output] : ((OOC Chance at 50%)) Jared Lyall's attempt has failed.
[2018-09-08 13:44:15] [Output] : ★ Jared Lyall tries once more.
[2018-09-08 13:44:18] [Output] : ((OOC Luck)) Jared Lyall tries their luck from 1 to 150 and gets 115.
[2018-09-08 13:44:25] [Output] : ★ Jared Lyall succeeds at removing the bolt.
[2018-09-08 13:44:35] [Output] : ★ Jared Lyall reaches for a chain, slinging it through the rear.
[2018-09-08 13:44:43] [Output] : ★ Jared Lyall wraps a seatbelt on the front of the vehicle.
[2018-09-08 13:44:48] [Output] : ★ Jared Lyall connects the chain to the seatbelt using a bolt.
[2018-09-08 13:44:58] [Output] : ★ Jared Lyall ensures they are wrapped up against the engine and transmission.
[2018-09-08 13:45:09] [Output] : ★ Jared Lyall hooks them up to the crane.
[2018-09-08 13:45:16] [Output] : ★ Jared Lyall raises the crane a bit, loosening up the tension.
[2018-09-08 13:45:22] [Output] : ★ Jared Lyall removes the remaining bolts.
[2018-09-08 13:45:32] [Output] : ★ Jared Lyall slowly raises the engine using the crane.
[2018-09-08 13:46:02] [Output] : ★ Jared Lyall enters the vehicle's driver seat.
[2018-09-08 13:46:09] [Output] : ★ Jared Lyall removes two screws from under the AC vent.
[2018-09-08 13:46:27] [Output] : ★ Jared Lyall pulls out the display unit.
[2018-09-08 13:46:32] [Output] : ★ Jared Lyall removes two plugs holding the display unit into its place.
[2018-09-08 13:46:43] [Output] : ★ Jared Lyall places the display unit and AC vent into a box.
[2018-09-08 13:46:57] [Output] : ★ Jared Lyall moves both seats to the farthest point they can to the front.
[2018-09-08 13:47:08] [Output] : ★ Jared Lyall removes 5 t50 bolts from under the seats on their pathway.
[2018-09-08 13:47:13] [Output] : ★ Jared Lyall removes a couple of electric wires.
[2018-09-08 13:47:21] [Output] : ★ Jared Lyall removes a shorter t50 bolt from the seatbelt.
[2018-09-08 13:47:25] [Output] : ★ Jared Lyall pushes the seats back.
[2018-09-08 13:47:35] [Output] : ★ Jared Lyall removes two bolts from the front of the seats' pathway.
[2018-09-08 13:48:02] [Output] : ★ Jared Lyall pops the latch down (on the back of the seats) and removes the wire connecting -
[2018-09-08 13:48:04] [Output] : ★ - them to the seatbelt.      ((Jared Lyall))
[2018-09-08 13:48:10] [Output] : ★ Jared Lyall removes the socket from the seats.
[2018-09-08 13:48:16] [Output] : ★ Jared Lyall opens both doors entirely.
[2018-09-08 13:48:27] [Output] : ★ Jared Lyall slowly carries the first seat to the truck, he puts it inside.
[2018-09-08 13:48:32] [Output] : ★ Jared Lyall reaches for the passenger door, opening it entirely.
[2018-09-08 13:48:42] [Output] : ★ Jared Lyall slowly carries the passenger seat to the truck, putting it inside as well.
[2018-09-08 13:48:56] [Output] : ★ Jared Lyall packs up the boxes and places them into the truck.
[2018-09-08 13:49:08] [Output] : ★ Jared Lyall places the engine and transmission using the crane into a box in the truck.