dmesg

rdered ports=1
fsl-ehci fsl-ehci.1: reset hcc_params 0006 thresh 0 uframes 256/512/1024 park
fsl-ehci fsl-ehci.1: park 0
fsl-ehci fsl-ehci.1: reset command 0080b02  park=3 ithresh=8 period=1024 Reset HALT
fsl-ehci fsl-ehci.1: ...powerdown ports...
fsl-ehci fsl-ehci.1: supports USB remote wakeup
fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
fsl-ehci fsl-ehci.1: init command 0010005 (park)=0 ithresh=1 period=512 RUN
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: Freescale On-Chip EHCI Host Controller
usb usb2: Manufacturer: Linux 3.0.15-01386-g5c661b1 ehci_hcd
usb usb2: SerialNumber: fsl-ehci.1
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: individual port power switching
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: Single TT
hub 2-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '001'
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
ARC USBOTG Device Controller driver (1 August 2005)
mousedev: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
tsc2004_prepare_for_reading: write_cmd -5
tsc2004: probe of 2-0048 failed with error -5
egalax_ts 2-0004: egalax_ts: failed to read firmware version
egalax_ts: probe of 2-0004 failed with error -5
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18
hub 2-0:1.0: port 1: status 0101 change 0000
hub 2-0:1.0: state 7 ports 1 chg 0002 evt 0000
hub 2-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20
mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video21
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci sdhci-esdhc-imx.2: no write-protect pin available!
mmc0: Unknown controller version (3). You may experience problems.
Registered led device: mmc0::
mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
sdhci sdhci-esdhc-imx.3: no write-protect pin available!
mmc1: Unknown controller version (3). You may experience problems.
Registered led device: mmc1::
mmc1: SDHCI controller on platform [sdhci-esdhc-imx.3] using ADMA
mmc2: Unknown controller version (3). You may experience problems.
usb 2-1: new high speed USB device number 2 using fsl-ehci
mmc0: host does not support reading read-only switch. assuming write-enable.
Registered led device: mmc2::
mmc0: new SDHC card at address 0002
mmc2: SDHCI controller on platform [sdhci-esdhc-imx.1] using ADMA
mmcblk0: mmc0:0002 SD4GB 3.69 GiB
mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
 mmcblk0: p1
VPU initialized
mxc_asrc registered
Anatop Thermal registered as thermal_zone0
anatop_thermal_probe: default cooling device is cpufreq!
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
sgtl5000 0-000a: Failed to get supply 'VDDD': -19
print_constraints: 0-000a: 850 <--> 1600 mV at 1200 mV normal
sgtl5000 0-000a: sgtl5000 revision 17
asoc: sgtl5000 <-> imx-ssi.1 mapping ok
asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
ALSA device list:
  #0: sgtl5000-audio
  #1: imx-hdmi-soc
usb 2-1: udev 2, busnum 2, minor = 129
usb 2-1: New USB device found, idVendor=0424, idProduct=2513
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
NET: Registered protocol family 26
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
usb 2-1: usb_probe_device
usb 2-1: configuration #1 chosen from 1 choice
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
lib80211_crypt: registered algorithm 'WEP'
lib80211_crypt: registered algorithm 'CCMP'
lib80211_crypt: registered algorithm 'TKIP'
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
Bus freq driver module loaded
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
hub 2-1:1.0: usb_probe_interface
hub 2-1:1.0: usb_probe_interface - got id
hub 2-1:1.0: USB hub found
mxc_dvfs_core_probe
DVFS driver module loaded
snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 04:52:19 UTC (17539)
hub 2-1:1.0: 3 ports detected
hub 2-1:1.0: standalone hub
hub 2-1:1.0: individual port power switching
hub 2-1:1.0: individual port over-current protection
hub 2-1:1.0: TT per port
hub 2-1:1.0: TT requires at most 8 FS bit times (666 ns)
hub 2-1:1.0: power on to power good time: 100ms
hub 2-1:1.0: local power source is good
hub 2-1:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '002'
hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0002
EXT3-fs: barriers not enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p1): using internal journal
EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 179:1.
Freeing init memory: 180K
hub 2-1:1.0: port 2: status 0301 change 0001
usb 2-1: link qh256-0001/ba3e6b80 start 1 [1/0 us]
hub 2-1:1.0: state 7 ports 3 chg 0004 evt 0000
hub 2-1:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
usb 2-1.2: new low speed USB device number 3 using fsl-ehci
usb 2-1.2: skipped 1 descriptor after interface
usb 2-1.2: default language 0x0409
usb 2-1.2: udev 3, busnum 2, minor = 130
usb 2-1.2: New USB device found, idVendor=413c, idProduct=2105
usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1.2: Product: Dell USB Keyboard
usb 2-1.2: Manufacturer: Dell
usb 2-1.2: usb_probe_device
usb 2-1.2: configuration #1 chosen from 1 choice
usb 2-1.2: adding 2-1.2:1.0 (config #1, interface 0)
usbhid 2-1.2:1.0: usb_probe_interface
usbhid 2-1.2:1.0: usb_probe_interface - got id
input: Dell Dell USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2:1.0/input/input1
b_session_irq_enable:otgsc=0x13c1120
USB Host suspend begins
will suspend roothub and its children
hub 1-0:1.0: hub_suspend
usb usb1: bus suspend
ehci_fsl_bus_suspend begins, DR
fsl-ehci fsl-ehci.0: suspend root hub
ehci_fsl_bus_suspend ends, DR
host suspend ends
b_session_irq_enable: the usb is in low power mode, vbus should not changed
usb 2-1.2: link qh16-0601/ba3e6300 start 2 [1/2 us]
generic-usb 0003:413C:2105.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-fsl-ehci.1-1.2/input0
drivers/usb/core/inode.c: creating file '003'
Thermal: fuse data 0x58e5523a
anatop_thermal_counting_ratio: raw25c=1422 raw_hot=1362 hot_temp=58
Division by zero in kernel.
[<800411b4>] (unwind_backtrace+0x0/0xfc) from [<8021e814>] (Ldiv0+0x8/0x10)
[<8021e814>] (Ldiv0+0x8/0x10) from [<80251124>] (mxcfb_check_var+0x128/0x310)
[<80251124>] (mxcfb_check_var+0x128/0x310) from [<80239208>] (fb_set_var+0x44/0x2a4)
[<80239208>] (fb_set_var+0x44/0x2a4) from [<8035fba0>] (release_disp_output+0xfc/0x164)
[<8035fba0>] (release_disp_output+0xfc/0x164) from [<8036139c>] (mxc_vout_release+0x64/0x70)
[<8036139c>] (mxc_vout_release+0x64/0x70) from [<803528d4>] (v4l2_release+0x54/0x78)
[<803528d4>] (v4l2_release+0x54/0x78) from [<800e6fcc>] (fput+0xb8/0x1e4)
[<800e6fcc>] (fput+0xb8/0x1e4) from [<800e37ec>] (filp_close+0x64/0x84)
[<800e37ec>] (filp_close+0x64/0x84) from [<800e38b0>] (sys_close+0xa4/0xe0)
[<800e38b0>] (sys_close+0xa4/0xe0) from [<8003b5c0>] (ret_fast_syscall+0x0/0x30)
------------[ cut here ]------------
WARNING: at mm/page_alloc.c:2106 __alloc_pages_nodemask+0x50c/0x6ec()
Modules linked in:
[<800411b4>] (unwind_backtrace+0x0/0xfc) from [<80063e50>] (warn_slowpath_common+0x4c/0x64)
[<80063e50>] (warn_slowpath_common+0x4c/0x64) from [<80063e84>] (warn_slowpath_null+0x1c/0x24)
[<80063e84>] (warn_slowpath_null+0x1c/0x24) from [<800b4730>] (__alloc_pages_nodemask+0x50c/0x6ec)
[<800b4730>] (__alloc_pages_nodemask+0x50c/0x6ec) from [<800444f4>] (__dma_alloc+0xd4/0x2fc)
[<800444f4>] (__dma_alloc+0xd4/0x2fc) from [<8004476c>] (dma_alloc_writecombine+0x24/0x2c)
[<8004476c>] (dma_alloc_writecombine+0x24/0x2c) from [<8024fcb8>] (mxcfb_set_par+0x3e4/0x4c0)
[<8024fcb8>] (mxcfb_set_par+0x3e4/0x4c0) from [<8023932c>] (fb_set_var+0x168/0x2a4)
[<8023932c>] (fb_set_var+0x168/0x2a4) from [<8035fba0>] (release_disp_output+0xfc/0x164)
[<8035fba0>] (release_disp_output+0xfc/0x164) from [<8036139c>] (mxc_vout_release+0x64/0x70)
[<8036139c>] (mxc_vout_release+0x64/0x70) from [<803528d4>] (v4l2_release+0x54/0x78)
[<803528d4>] (v4l2_release+0x54/0x78) from [<800e6fcc>] (fput+0xb8/0x1e4)
[<800e6fcc>] (fput+0xb8/0x1e4) from [<800e37ec>] (filp_close+0x64/0x84)
[<800e37ec>] (filp_close+0x64/0x84) from [<800e38b0>] (sys_close+0xa4/0xe0)
[<800e38b0>] (sys_close+0xa4/0xe0) from [<8003b5c0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 678f5059f10e1565 ]---
mxc_sdc_fb mxc_sdc_fb.0: Unable to allocate framebuffer memory
detected fb_set_par error, error code: -12
mxc_v4l2_output mxc_v4l2_output.0: ERR: fb_set_var.
Division by zero in kernel.
[<800411b4>] (unwind_backtrace+0x0/0xfc) from [<8021e814>] (Ldiv0+0x8/0x10)
[<8021e814>] (Ldiv0+0x8/0x10) from [<80251124>] (mxcfb_check_var+0x128/0x310)
[<80251124>] (mxcfb_check_var+0x128/0x310) from [<80239208>] (fb_set_var+0x44/0x2a4)
[<80239208>] (fb_set_var+0x44/0x2a4) from [<8035fba0>] (release_disp_output+0xfc/0x164)
[<8035fba0>] (release_disp_output+0xfc/0x164) from [<8036139c>] (mxc_vout_release+0x64/0x70)
[<8036139c>] (mxc_vout_release+0x64/0x70) from [<803528d4>] (v4l2_release+0x54/0x78)
[<803528d4>] (v4l2_release+0x54/0x78) from [<800e6fcc>] (fput+0xb8/0x1e4)
[<800e6fcc>] (fput+0xb8/0x1e4) from [<800e37ec>] (filp_close+0x64/0x84)
[<800e37ec>] (filp_close+0x64/0x84) from [<800e38b0>] (sys_close+0xa4/0xe0)
[<800e38b0>] (sys_close+0xa4/0xe0) from [<8003b5c0>] (ret_fast_syscall+0x0/0x30)
Division by zero in kernel.
[<800411b4>] (unwind_backtrace+0x0/0xfc) from [<8021e814>] (Ldiv0+0x8/0x10)
[<8021e814>] (Ldiv0+0x8/0x10) from [<8024ab80>] (ldb_disp_setup+0xd0/0x170)
[<8024ab80>] (ldb_disp_setup+0xd0/0x170) from [<8024f908>] (mxcfb_set_par+0x34/0x4c0)
[<8024f908>] (mxcfb_set_par+0x34/0x4c0) from [<8023932c>] (fb_set_var+0x168/0x2a4)
[<8023932c>] (fb_set_var+0x168/0x2a4) from [<8035fba0>] (release_disp_output+0xfc/0x164)
[<8035fba0>] (release_disp_output+0xfc/0x164) from [<8036139c>] (mxc_vout_release+0x64/0x70)
[<8036139c>] (mxc_vout_release+0x64/0x70) from [<803528d4>] (v4l2_release+0x54/0x78)
[<803528d4>] (v4l2_release+0x54/0x78) from [<800e6fcc>] (fput+0xb8/0x1e4)
[<800e6fcc>] (fput+0xb8/0x1e4) from [<800e37ec>] (filp_close+0x64/0x84)
[<800e37ec>] (filp_close+0x64/0x84) from [<800e38b0>] (sys_close+0xa4/0xe0)
[<800e38b0>] (sys_close+0xa4/0xe0) from [<8003b5c0>] (ret_fast_syscall+0x0/0x30)
mxc_sdc_fb mxc_sdc_fb.2: Unable to allocate framebuffer memory
detected fb_set_par error, error code: -12
mxc_v4l2_output mxc_v4l2_output.0: ERR: fb_set_var.
usb usb1: usb auto-resume
ehci_fsl_bus_resume begins, DR
usb usb1: bus resume fail, err -108
init: plymouth main process (1289) killed by SEGV signal
init: plymouth-splash main process (4874) terminated with status 2
init: avahi-daemon main process (4940) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4945) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4950) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4955) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4960) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4965) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4970) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4975) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4980) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4985) terminated with status 255
init: avahi-daemon main process ended, respawning
init: avahi-daemon main process (4990) terminated with status 255
init: avahi-daemon respawning too fast, stopped
init: failsafe main process (4997) killed by TERM signal
eth5: Freescale FEC PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=1:06, irq=-1)
init: statd main process (5055) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5066) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5087) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5107) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5115) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5123) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5132) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5140) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5152) terminated with status 1
init: statd main process ended, respawning
init: statd main process (5160) terminated with status 1
init: statd main process ended, respawning
init: apport pre-start process (5177) terminated with status 1
init: apport post-stop process (5199) terminated with status 1
init: statd main process (5203) terminated with status 1
init: statd respawning too fast, stopped
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
init: lightdm main process (5198) terminated with status 1
init: tty1 main process (5410) killed by TERM signal