daily pastebin goal
68%
SHARE
TWEET

WCNSS_qcom_cfg.ini

a guest Mar 23rd, 2019 109 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. # This file allows user to override the factory
  2.  
  3. # defaults for the WLAN Driver
  4.  
  5. # ARP rates toggling
  6. gToggleArpBDRates=1
  7.  
  8. # INI parameter used to control SSR test framework
  9. # Set its value to 1 to enable APPS triggered SSR testing
  10. gEnableForceTargetAssert=1
  11.  
  12. # Enable MCC Mode
  13. gEnableMCCMode=1
  14.  
  15. # Enable IMPS or not
  16. gEnableImps=1
  17.  
  18. # Enable/Disable Idle Scan
  19.  
  20. gEnableIdleScan=0
  21.  
  22.  
  23. # Increase sleep duration (seconds) during IMPS
  24. # 0 implies no periodic wake up from IMPS. Periodic wakeup is
  25. # unnecessary if Idle Scan is disabled.
  26. gImpsModSleepTime=0
  27.  
  28.  
  29. # Enable BMPS or not
  30. gEnableBmps=1
  31.  
  32. # Disable QCOM SAR cutback algorithm and its default driver value
  33. SARPowerBackoff=0
  34.  
  35. # Enable suspend or not
  36.  
  37. # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
  38.  
  39. gEnableSuspend=3
  40.  
  41.  
  42. # Phy Mode (auto, b, g, n, etc)
  43. # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
  44. gDot11Mode=0
  45.  
  46.  
  47. # CSR Roaming Enable(1) Disable(0)
  48.  
  49. gRoamingTime=0
  50.  
  51.  
  52. # Assigned MAC Addresses - This will be used until NV items are in place
  53.  
  54. # Each byte of MAC address is represented in Hex format as XX
  55.  
  56. Intf0MacAddress=000AF58989FF
  57. Intf1MacAddress=000AF58989FE
  58. Intf2MacAddress=000AF58989FD
  59.  
  60. Intf3MacAddress=000AF58989FC
  61.  
  62. # Set/Clear UAPSD mask
  63.  
  64. UapsdMask=0
  65.  
  66. # UAPSD service interval for VO,VI, BE, BK traffic
  67.  
  68. InfraUapsdVoSrvIntv=20
  69.  
  70. InfraUapsdViSrvIntv=40
  71.  
  72. # Flag to allow STA send AddTspec even when ACM is Off
  73. gAddTSWhenACMIsOff=1
  74.  
  75. # Make 1x1 the default antenna configuration
  76.  
  77. gNumRxAnt=1
  78.  
  79.  
  80. # Beacon filtering frequency (unit in beacon intervals)
  81.  
  82. gNthBeaconFilter=50
  83.  
  84.  
  85. # Enable WAPI or not
  86.  
  87. # WAPIIsEnabled=0
  88.  
  89.  
  90. # Flags to filter Mcast abd Bcast RX packets.
  91.  
  92. # Value 0: No filtering, 1: Filter all Multicast.
  93.  
  94. # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
  95.  
  96. McastBcastFilter=0
  97.  
  98. #Enable NDP offload
  99. hostNSOffload=1
  100.  
  101. #Flag to enable HostARPOffload feature or not
  102.  
  103. hostArpOffload=1
  104.  
  105.  
  106. #SoftAP Related Parameters
  107.  
  108. # AP MAc addr
  109.  
  110. gAPMacAddr=000AF589dcab
  111.  
  112.  
  113. # 802.11n Protection flag
  114.  
  115. gEnableApProt=1
  116.  
  117.  
  118. #Enable OBSS protection
  119.  
  120. gEnableApOBSSProt=1
  121.  
  122.  
  123. #Enable/Disable UAPSD for SoftAP
  124.  
  125. gEnableApUapsd=1
  126.  
  127.  
  128. # Fixed Rate
  129.  
  130. gFixedRate=0
  131.  
  132.  
  133. # Maximum Tx power
  134.  
  135. # gTxPowerCap=30
  136.  
  137.  
  138. # Fragmentation Threshold
  139.  
  140. # gFragmentationThreshold=2346
  141.  
  142.  
  143. # RTS threshold
  144.  
  145. RTSThreshold=2347
  146.  
  147.  
  148. # Intra-BSS forward
  149.  
  150. gDisableIntraBssFwd=0
  151.  
  152.  
  153. # WMM Enable/Disable
  154.  
  155. WmmIsEnabled=0
  156.  
  157.  
  158. # 802.11d support
  159.  
  160. g11dSupportEnabled=0
  161.  
  162. # CCX Support and fast transition
  163. EseEnabled=0
  164. FastTransitionEnabled=1
  165. ImplicitQosIsEnabled=0
  166. gNeighborScanTimerPeriod=200
  167.  
  168. # default value of this parameter is zero to enable dynamic threshold allocation
  169. # to set static roming threshold uncomment below parameter and set vaule
  170. #gNeighborLookupThreshold=78
  171.  
  172. gNeighborScanChannelMinTime=20
  173. gNeighborScanChannelMaxTime=30
  174.  
  175. # Legacy (non-CCX, non-802.11r) Fast Roaming Support
  176. # To enable, set FastRoamEnabled=1
  177. # To disable, set FastRoamEnabled=0
  178. FastRoamEnabled=1
  179.  
  180. #Check if the AP to which we are roaming is better than current AP in terms of RSSI.
  181. #Checking is disabled if set to Zero.Otherwise it will use this value as to how better
  182. #the RSSI of the new/roamable AP should be for roaming
  183. RoamRssiDiff=5
  184.  
  185. # SAP Country code
  186.  
  187. # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
  188.  
  189. # Example
  190.  
  191. #   US Indoor, USI
  192.  
  193. #   Korea Outdoor, KRO
  194.  
  195. #   Japan without optional byte, JP
  196.  
  197. #   France without optional byte, FR
  198.  
  199. #gAPCntryCode=USI
  200.  
  201.  
  202. #Short Guard Interval Enable/disable
  203.  
  204. gShortGI20Mhz=1
  205.  
  206. gShortGI40Mhz=1
  207.  
  208.  
  209. #Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
  210.  
  211. gAPAutoShutOff=0
  212.  
  213.  
  214. # SAP auto channel selection configuration
  215.  
  216. # 0 = disable auto channel selection
  217.  
  218. # 1 = enable auto channel selection, channel provided by supplicant will be ignored
  219.  
  220. gApAutoChannelSelection=0
  221.  
  222.  
  223. # Listen Energy Detect Mode Configuration
  224.  
  225. # Valid values 0-128
  226.  
  227. # 128 means disable Energy Detect feature
  228.  
  229. # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
  230.  
  231. # 10-128 are reserved.
  232.  
  233. # The EDET threshold mapping is as follows in 3dB step:
  234.  
  235. # 0 = -60 dBm
  236.  
  237. # 1 = -63 dBm
  238.  
  239. # 2 = -66 dBm
  240.  
  241. # ...
  242.  
  243. # 7 = -81 dBm
  244.  
  245. # 8 = -84 dBm
  246.  
  247. # 9 = -87 dBm
  248.  
  249. # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
  250.  
  251. #
  252.  
  253. #  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.
  254.  
  255. #
  256.  
  257. gEnablePhyAgcListenMode=128
  258.  
  259.  
  260. #Preferred channel to start BT AMP AP mode (0 means, any channel)
  261.  
  262. BtAmpPreferredChannel=0
  263.  
  264.  
  265. #Preferred band (both or 2.4 only or 5 only)
  266.  
  267. BandCapability=0
  268.  
  269.  
  270. #Beacon Early Termination (1 = enable the BET feature, 0 = disable)
  271.  
  272. enableBeaconEarlyTermination=1
  273.  
  274. beaconEarlyTerminationWakeInterval=11
  275.  
  276.  
  277. #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
  278.  
  279. gEnableBtAmp=0
  280.  
  281.  
  282. #SOFTAP Channel Range selection
  283.  
  284. gAPChannelSelectStartChannel=1
  285.  
  286. gAPChannelSelectEndChannel=11
  287.  
  288.  
  289. #SOFTAP Channel Range selection Operating band
  290.  
  291. # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
  292.  
  293. gAPChannelSelectOperatingBand=0
  294.  
  295.  
  296. #Channel Bonding
  297. gChannelBondingMode5GHz=1
  298.  
  299. gEnableModulatedDTIM = 3
  300. gMaxLIModulatedDTIM = 3
  301. gEnableDatainactivity = 200
  302.  
  303. #Enable Keep alive with non-zero period value
  304.  
  305. gStaKeepAlivePeriod=30
  306.  
  307.  
  308. #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
  309. #For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
  310. #For both active and power save clients.
  311.  
  312. #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
  313. #If doesn't honor for 5 seconds then Driver remove client.
  314.  
  315. #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on
  316. #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
  317. #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod)..
  318.  
  319. #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
  320. #where we send NULL frame.
  321.  
  322. #gApLinkMonitorPeriod = 10
  323.  
  324. #gGoLinkMonitorPeriod = 10
  325.  
  326. #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
  327. #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
  328. gGoKeepAlivePeriod = 10
  329.  
  330. gApKeepAlivePeriod = 30
  331. #If set will start with active scan after driver load, otherwise will start with
  332.  
  333. #passive scan to find out the domain
  334.  
  335. #gEnableBypass11d=1
  336.  
  337.  
  338. #If set to 0, will not scan DFS channels
  339.  
  340. gEnableDFSChnlScan=1
  341.  
  342. gEnableLogp=1
  343.  
  344.  
  345. # Enable Automatic Tx Power control
  346.  
  347. gEnableAutomaticTxPowerControl=0
  348.  
  349. # 0 for OLPC 1 for CLPC and SCPC
  350. gEnableCloseLoop=1
  351.  
  352. #Data Inactivity Timeout when in powersave (in ms)
  353. gDataInactivityTimeout=200
  354.  
  355. gEnableLpwrImgTransition=1
  356.  
  357. # Scan Timing Parameters
  358. # gPassiveMaxChannelTime=110
  359. # gPassiveMinChannelTime=60
  360. # Enable Tx LDPC
  361. #gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
  362. gTxLdpcEnable=3
  363. # gActiveMaxChannelTime=40
  364. # gActiveMinChannelTime=20
  365.  
  366. gNumStaChanCombinedConc=1
  367.  
  368. # Valid values are 2048,4096,8192 and so on
  369. # Please don't use values other than the ones mentioned above
  370. gMaxMediumTime=4096
  371.  
  372. # 802.11K support
  373. gRrmEnable=1
  374. gRrmOperChanMax=8
  375. gRrmNonOperChanMax=8
  376. gRrmRandIntvl=100
  377.  
  378. #Scan offload
  379. gEnableDirectedScanOffload=0
  380.  
  381. #FlexConnect Power Factor
  382. #Default is set to 0 (disable)
  383. gFlexConnectPowerFactor=0
  384.  
  385. gVhtChannelWidth=2
  386.  
  387. # VHT Tx/Rx MCS values
  388. # Valid values are 0,1,2. If commented out, the default value is 0.
  389. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
  390. gVhtRxMCS=2
  391. gVhtTxMCS=2
  392.  
  393. # Enable Tx beamforming
  394. gTxBFEnable=1
  395.  
  396. #Enable/Disable TDLS Feature
  397. gEnableTDLSSupport=1
  398.  
  399. #Enable/Disable TDLS Implicit Trigger
  400. gEnableTDLSImplicitTrigger=1
  401.  
  402. #Enable/Disable TDLS WMM Mode
  403. gEnableTDLSWmmMode=1
  404.  
  405. #Enable/Disable TDLS Buffer Sta
  406. gEnableTDLSBufferSta=1
  407.  
  408. #Enable/Disable Mgmt Frame Logging
  409. gEnableMgmtLogging=1
  410.  
  411. #Enable/Disable MAc Spoofing
  412.  
  413. #Set RPS CPU mask
  414. rps_mask=0f
  415.  
  416.  
  417. gEnableMacAddrSpoof=2
  418.  
  419. gEnableTDLSScan=1
  420. gTDLSExternalControl=1
  421. gEnableTDLSSupport=1
  422. gTDLSTxStatsPeriod=500
  423. gTDLSTxPacketThreshold=10
  424. gTDLSDiscoveryPeriod=20000
  425. gTDLSMaxDiscoveryAttempt=5
  426. gTDLSIdleTimeout=40000
  427. gTDLSRssiHysteresis=100
  428. gTDLSIdlePacketThreshold=5
  429. gEnableTDLSScanCoexistence=1
  430. gBtcEnableIndTimerVal=5
  431.  
  432. gBtcFastWlanConnPref=0
  433.  
  434. gIgnorePeerErpInfo=1
  435.  
  436. #Disable RTT as recommended by QC
  437. gEnableRTTSupport=0
  438.  
  439. END
  440.  
  441. # Note: Configuration parser would not read anything past the END marker
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top