Lowering (Supra)

[2017-04-06 01:39:54] [Output] :
[2017-04-06 01:40:18] [Output] : ★ Lukas Ruiz walks towards the workbench, wrapping his right hand around a tool box.
[2017-04-06 01:40:29] [Output] : ★ Lukas Ruiz walks towards the Supra, whilist carrying the box.
[2017-04-06 01:41:22] [Output] : ★ Lukas Ruiz drops it on the ground by the front left side of the vehicle, crouching.
[2017-04-06 01:41:47] [Output] : ★ Lukas Ruiz grasps a torque wrench from the toolbox, pointing it at one of the 5 screws on the-
[2017-04-06 01:41:50] [Output] : ★ wheel.      ((Lukas Ruiz))
[2017-04-06 01:42:02] [Output] : ★ Lukas Ruiz twists it counter-clockwise, completely loosening it.
[2017-04-06 01:42:21] [Output] : ★ Lukas Ruiz repeats the process for the remaining 4, as the wheel would be loose.
[2017-04-06 01:42:37] [Output] : ★ Lukas Ruiz applies strength around the wheel, wiggling it outwards from the hub.
[2017-04-06 01:42:49] [Output] : ★ Lukas Ruiz leans it against the fender, by his left.
[2017-04-06 01:43:07] [Output] : ★ With the wrench still on his hand, Lukas would reach for the side of the caliper facing-      ((Lukas Ruiz))
[2017-04-06 01:43:19] [Output] : ★ the engine, as he would untighten the two nuts holding the caliper-      ((Lukas Ruiz))
[2017-04-06 01:43:23] [Output] : ★ against the disk brake.      ((Lukas Ruiz))
[2017-04-06 01:43:40] [Output] : ★ As it would be done, Lukas would remove the caliper from it's position, dropping it-      ((Lukas Ruiz))
[2017-04-06 01:44:01] [Output] : ★ on the ground, next to the pads that had previously fallen onto the concrete, upon-      ((Lukas Ruiz))
[2017-04-06 01:44:06] [Output] : ★ the removal of the caliper.      ((Lukas Ruiz))
[2017-04-06 01:44:26] [Output] : ★ Lukas Ruiz then untightens the single nut on the center of the disk brake, making it loose.
[2017-04-06 01:44:42] [Output] : ★ Lukas Ruiz pushes it out with care, as he would lay it next to the caliper and pads.
[2017-04-06 01:45:06] [Output] : ★ Lukas Ruiz proceeds to pull off the brake fluid pipe.
[2017-04-06 01:45:13] [Output] : ★ The brake system would be completely out.      ((Lukas Ruiz))
[2017-04-06 01:45:29] [Output] : ★ Lukas Ruiz stands up, quickly going to the inside of the car, pulling the hood's lever.
[2017-04-06 01:45:41] [Output] : ★ Lukas Ruiz walks up towards the front of the car, popping the hood open.
[2017-04-06 01:45:58] [Output] : ★ Lukas Ruiz grabs a 15 sized wrench from the toolbox, as he would untighten the 3 screws-
[2017-04-06 01:46:06] [Output] : ★ on the top mount of the suspension.      ((Lukas Ruiz))
[2017-04-06 01:46:24] [Output] : ★ As the three would be off, Lukas would crouch on his previous position.      ((Lukas Ruiz))
[2017-04-06 01:46:46] [Output] : ★ Lukas Ruiz untightens the bottom of the suspension from the frame, as it would release the pressure,
[2017-04-06 01:46:54] [Output] : ★ falling onto the ground.      ((Lukas Ruiz))
[2017-04-06 01:47:03] [Output] : ★ Lukas Ruiz throws it away from his working place.
[2017-04-06 01:47:18] [Output] : ★ Lukas Ruiz stands up, grabbing the cardboard box sitting on the driver's seat.
[2017-04-06 01:47:22] [Output] : ★ Lukas Ruiz drags it outside.
[2017-04-06 01:47:41] [Output] : ★ Lukas Ruiz slides both hands inside, wrapping them around the new set of BC Racing coilovers.
[2017-04-06 01:48:01] [Output] : ★ Lukas Ruiz admires them with joy, as he would then slide one of the front coilovers-
[2017-04-06 01:48:06] [Output] : ★ in it's position.      ((Lukas Ruiz))
[2017-04-06 01:48:19] [Output] : ★ Lukas Ruiz assembles the bottom part of it, tightening the screws, with the assistance of the-
[2017-04-06 01:48:25] [Output] : ★ 15 size wrench.      ((Lukas Ruiz))
[2017-04-06 01:48:41] [Output] : ★ Lukas Ruiz moves onto the top mounts, as he would slide in the 3 screws, ligning the coilover-
[2017-04-06 01:48:45] [Output] : ★ correctly.      ((Lukas Ruiz))
[2017-04-06 01:48:57] [Output] : ★ Lukas Ruiz gives each a few rotations, clockwise, as he would fully tighten them.
[2017-04-06 01:49:13] [Output] : ★ As the new coilover would be in place, Lukas would assemble the brake kit back.      ((Lukas Ruiz))
[2017-04-06 01:49:35] [Output] : ★ He would start by sliding in the brake disk, tightening it with the torque wrench to the hub      ((Lukas Ruiz))
[2017-04-06 01:49:46] [Output] : ★ according to the amount of torque provided by the manufacturer.      ((Lukas Ruiz))
[2017-04-06 01:50:03] [Output] : ★ Lukas Ruiz then moves onto to sliding the pads inside the caliper, mounting it onto the disk.
[2017-04-06 01:50:18] [Output] : ★ Lukas Ruiz tightens it in place with the 2 nuts and the torque wrench.
[2017-04-06 01:50:38] [Output] : ★ To finalize the brake system, Lukas would attach the brake fluid pipe back in place,      ((Lukas Ruiz))
[2017-04-06 01:50:47] [Output] : ★ quickly inspecting from mistakes from his part.      ((Lukas Ruiz))
[2017-04-06 01:50:51] [Output] : ((OOC Chance at 70%)) Lukas Ruiz's attempt has succeeded.
[2017-04-06 01:51:00] [Output] : ★ Everything would be okay.      ((Lukas Ruiz))
[2017-04-06 01:51:11] [Output] : ★ Lukas Ruiz then moves on to grabbing the wheel back, sliding it in the hub.
[2017-04-06 01:51:30] [Output] : ★ Lukas Ruiz mounts the 5 nuts, tightening each only a bit with the torque wrench.
[2017-04-06 01:51:46] [Output] : ★ Upon checking if the wheel was correctly position, Lukas would proceed to-      ((Lukas Ruiz))
[2017-04-06 01:51:58] [Output] : ★ completely tighten the nuts 1 by 1, following a star pattern.      ((Lukas Ruiz))
[2017-04-06 01:52:08] [Output] : ★ Lukas Ruiz repeats the process for the remaining 3 stages of the car.
[2017-04-06 01:52:16] [Output] : ★ The Toyota would be lowered a few inches.      ((Lukas Ruiz))