Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- unielec U7628-01 boot with original software via serial at 57600
- [04030C0A][04030C0C]
- DDR Calibration DQS reg = 00008786
- U-Boot 1.1.3 (May 20 2018 - 05:24:52)
- Board: Ralink APSoC DRAM: 64 MB
- relocate_code Pointer at: 83fb8000
- flash manufacture id: c2, device id 20 18
- find flash: MX25L12805D
- ============================================
- Ralink UBoot Version: 4.3.0.0
- --------------------------------------------
- ASIC 7628_MP (Port5<->None)
- DRAM component: 512 Mbits DDR, width 16
- DRAM bus: 16 bit
- Total memory: 64 MBytes
- Flash component: SPI Flash
- Date:May 20 2018 Time:05:24:52
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 575 MHZ ####
- estimate memory size =64 Mbytes
- RESET MT7628 PHY!!!!!!
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 7: Load Boot Loader code then write to Flash via Serial.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 0
- 3: System Boot system code via Flash.
- ## Booting image at bc050000 ...
- Image Name: OpenWrt Linux-3.10.14-p112871
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1266738 Bytes = 1.2 MB
- Load Address: 80000000
- Entry Point: 80000000
- Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 64
- Starting kernel ...
- LINUX started...
- THIS IS ASIC
- [ 0.000000] Linux version 3.10.14 (root@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #11 Thu Aug 9 05:53:38 PDT 2018
- [ 0.000000]
- [ 0.000000] The CPU feqenuce set to 575 MHz
- [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
- [ 0.000000] Software DMA cache coherency
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 08000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x07ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
- [ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
- [ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Writing ErrCtl register=0002ba2a
- [ 0.000000] Readback ErrCtl register=0002ba2a
- [ 0.000000] Memory: 125996k/131072k available (2818k kernel code, 5044k reserved, 672k data, 220k init, 0k highmem)
- [ 0.000000] NR_IRQS:128
- [ 0.000000] console [ttyS1] enabled
- [ 0.096000] Calibrating delay loop... 382.46 BogoMIPS (lpj=764928)
- [ 0.128000] pid_max: default: 32768 minimum: 301
- [ 0.132000] Mount-cache hash table entries: 512
- [ 0.136000] NET: Registered protocol family 16
- [ 0.140000] RALINK_GPIOMODE = 54050404
- [ 0.144000] RALINK_GPIOMODE = 54040404
- [ 0.244000] ***** Xtal 40MHz *****
- [ 0.248000] start PCIe register access
- [ 0.748000] RALINK_RSTCTRL = 2400000
- [ 0.752000] RALINK_CLKCFG1 = fdbfffc0
- [ 0.756000]
- [ 0.756000] *************** MT7628 PCIe RC mode *************
- [ 1.256000] PCIE0 no card, disable it(RST&CLK)
- [ 1.284000] bio: create slab <bio-0> at 0
- [ 1.288000] usbcore: registered new interface driver usbfs
- [ 1.292000] usbcore: registered new interface driver hub
- [ 1.296000] usbcore: registered new device driver usb
- [ 1.300000] cfg80211: Calling CRDA to update world regulatory domain
- [ 1.304000] Switching to clocksource MIPS
- [ 1.308000] NET: Registered protocol family 2
- [ 1.320000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- [ 1.332000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 1.344000] TCP: Hash tables configured (established 1024 bind 1024)
- [ 1.360000] TCP: reno registered
- [ 1.364000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 1.376000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 1.388000] NET: Registered protocol family 1
- [ 1.400000] MTK/Ralink EHCI/OHCI init.
- [ 1.408000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 1.420000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 1.440000] msgmni has been set to 246
- [ 1.448000] io scheduler noop registered (default)
- [ 1.468000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 1.480000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
- [ 1.492000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
- [ 1.508000] Ralink gpio driver initialized
- [ 1.516000] flash manufacture id: c2, device id 20 18
- [ 1.528000] MX25L12805D(c2 2018c220) (16384 Kbytes)
- [ 1.536000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
- [ 1.556000] Creating 5 MTD partitions on "raspi":
- [ 1.568000] 0x000000000000-0x000001000000 : "ALL"
- [ 1.576000] 0x000000000000-0x000000030000 : "Bootloader"
- [ 1.588000] 0x000000030000-0x000000040000 : "Config"
- [ 1.600000] 0x000000040000-0x000000050000 : "Factory"
- [ 1.612000] 0x000000050000-0x000001000000 : "firmware"
- [ 1.624000] 0x000000185472-0x000001000000 : "rootfs"
- [ 1.636000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
- [ 1.660000] mtd: partition "rootfs_data" created automatically, ofs=0x470000, len=0xb90000
- [ 1.676000] 0x000000470000-0x000001000000 : "rootfs_data"
- [ 1.688000] GMAC1_MAC_ADRH -- : 0x00008c88
- [ 1.700000] GMAC1_MAC_ADRL -- : 0x2b00000d
- [ 1.708000] Ralink APSoC Ethernet Driver Initilization. v3.1 256 rx/tx descriptors allocated, mtu = 1500!
- [ 1.724000] GMAC1_MAC_ADRH -- : 0x00008c88
- [ 1.732000] GMAC1_MAC_ADRL -- : 0x2b00000d
- [ 1.744000] PROC INIT OK!
- [ 1.748000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 1.760000] ehci-pci: EHCI PCI platform driver
- [ 1.772000] ehci-platform: EHCI generic platform driver
- [ 1.800000] ******MT7628 mtk phy
- [ 1.808000] *****run project phy.
- [ 1.824000] FM_OUT value: u4FmOut = 0(0x00000000)
- [ 1.840000] FM_OUT value: u4FmOut = 137(0x00000089)
- [ 1.848000] FM detection done! loop = 1
- [ 1.864000] SR calibration value u1SrCalVal = 6
- [ 1.872000] *********Execute mt7628_phy_init!!
- [ 1.880000] ehci-platform ehci-platform: EHCI Host Controller
- [ 1.892000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 1.908000] ehci-platform ehci-platform: irq 18, io mem 0x101c0000
- [ 1.932000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
- [ 1.944000] hub 1-0:1.0: USB hub found
- [ 1.952000] hub 1-0:1.0: 1 port detected
- [ 1.960000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 1.992000] *********Execute mt7628_phy_init!!
- [ 2.000000] ohci-platform ohci-platform: Generic Platform OHCI Controller
- [ 2.016000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
- [ 2.032000] ohci-platform ohci-platform: irq 18, io mem 0x101c1000
- [ 2.104000] hub 2-0:1.0: USB hub found
- [ 2.112000] hub 2-0:1.0: 1 port detected
- [ 2.120000] TCP: cubic registered
- [ 2.128000] NET: Registered protocol family 10
- [ 2.136000] NET: Registered protocol family 17
- [ 2.144000] 8021q: 802.1Q VLAN Support v1.8
- [ 2.184000] registered taskstats version 1
- [ 2.200000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 2.216000] Freeing unused kernel memory: 220K (80369000 - 803a0000)
- procd: Console is alive
- [ 4.544000] SCSI subsystem initialized
- [ 4.560000] uhci_hcd: USB Universal Host Controller Interface driver
- [ 4.584000] usbcore: registered new interface driver usb-storage
- procd: - preinit -
- [ 5.452000] Raeth v3.1 (Tasklet,SkbRecycle)
- [ 5.464000]
- [ 5.464000] phy_tx_ring = 0x07007000, tx_ring = 0xa7007000
- [ 5.476000]
- [ 5.476000] phy_rx_ring0 = 0x07008000, rx_ring0 = 0xa7008000
- [ 5.508000] GMAC1_MAC_ADRH -- : 0x00008c88
- [ 5.516000] GMAC1_MAC_ADRL -- : 0x2b00000d
- [ 5.524000] RT305x_ESW: Link Status Changed
- Press the [f] key and hit [enter] to enter failsafe mode
- Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- kmod: ran 1 iterations
- [ 9.072000] jffs2: notice: (256) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 0 orphan) found.
- block: extroot: no root or overlay mount defined
- jffs2 is ready
- jffs2 is ready
- [ 9.176000] jffs2: notice: (253) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 0 orphan) found.
- switching to overlay
- [ 9.220000] ra2880stop()...Done
- [ 9.224000] Free TX/RX Ring Memory!
- procd: - early -
- procd: - ubus -
- procd: - init -
- Please press Enter to activate this console.
- [ 12.212000] NTFS driver 2.1.30 [Flags: R/O MODULE].
- [ 12.252000] nf_conntrack version 0.5.0 (1972 buckets, 7888 max)
- [ 12.280000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.120000]
- [ 13.120000]
- [ 13.120000] === pAd = c05fc000, size = 1476032 ===
- [ 13.120000]
- [ 13.140000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
- [ 13.152000] <-- RTMPAllocAdapterBlock, Status=0
- [ 13.160000] RtmpChipOpsHook(492): Not support for HIF_MT yet!
- [ 13.172000] mt7628_init()-->
- [ 13.180000] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
- [ 13.188000] e2.bin mt7628_init(1117)::(2), pChipCap->fw_len(63056)
- [ 13.200000] mt_bcn_buf_init(218): Not support for HIF_MT yet!
- [ 13.212000] <--mt7628_init()
- [ 13.228000] MTK MSDC device init.
- [ 13.256000] msdc0 -> ================ <- msdc_set_mclk() : L<686> PID<kmodloader><0x260>
- [ 13.272000] msdc0 -> !!! Set<400KHz> Source<48000KHz> -> sclk<400KHz> <- msdc_set_mclk() : L<687> PID<kmodloader><0x260>
- [ 13.292000] msdc0 -> ================ <- msdc_set_mclk() : L<688> PID<kmodloader><0x260>
- [ 13.328000] msdc0 -> ops_get_cd return<0> <- msdc_ops_get_cd() : L<2317> PID<kworker/u2:0><0x6>
- [ 13.348000] msdc0 -> set mclk to 0!!! <- msdc_set_mclk() : L<634> PID<kworker/u2:0><0x6>
- [ 13.364000] mtk-sd: MediaTek MT6575 MSDC Driver
- [ 14.040000] register rt2860
- [ 14.052000] usbcore: registered new interface driver cdc_acm
- [ 14.064000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
- [ 14.084000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 14.096000] Type=Linux
- [ 14.116000] Ralink APSoC Hardware Watchdog Timer
- [ 14.128000] rdm_major = 253
- [ 14.140000] usbcore: registered new interface driver usbserial
- [ 14.152000] usbcore: registered new interface driver usbserial_generic
- [ 14.168000] usbserial: USB Serial support registered for generic
- [ 14.196000] xt_time: kernel timezone is -0000
- [ 14.212000] PPP generic driver version 2.4.2
- [ 14.224000] NET: Registered protocol family 24
- [ 14.244000] usbcore: registered new interface driver option
- [ 14.252000] usbserial: USB Serial support registered for GSM modem (1-port)
- [ 20.460000] Raeth v3.1 (Tasklet,SkbRecycle)
- [ 20.468000]
- [ 20.468000] phy_tx_ring = 0x06b21000, tx_ring = 0xa6b21000
- [ 20.484000]
- [ 20.484000] phy_rx_ring0 = 0x06b22000, rx_ring0 = 0xa6b22000
- [ 20.512000] GMAC1_MAC_ADRH -- : 0x00008c88
- [ 20.520000] GMAC1_MAC_ADRL -- : 0x2b00000d
- [ 20.528000] RT305x_ESW: Link Status Changed
- [ 20.552000] device eth0.1 entered promiscuous mode
- [ 20.564000] device eth0 entered promiscuous mode
- [ 20.596000] br-lan: port 1(eth0.1) entered forwarding state
- [ 20.604000] br-lan: port 1(eth0.1) entered forwarding state
- procd: - init complete -
- [ 21.712000] TX_BCN DESC a6877000 size = 320
- [ 21.724000] RX[0] DESC a6879000 size = 2048
- [ 21.732000] RX[1] DESC a687a000 size = 1024
- [ 21.752000] E2pAccessMode=2
- [ 21.760000] cfg_mode=9
- [ 21.764000] cfg_mode=9
- [ 21.768000] wmode_band_equal(): Band Equal!
- [ 21.780000] APSDCapable[0]=1
- [ 21.788000] APSDCapable[1]=1
- [ 21.792000] APSDCapable[2]=1
- [ 21.800000] APSDCapable[3]=1
- [ 21.804000] APSDCapable[4]=1
- [ 21.808000] APSDCapable[5]=1
- [ 21.816000] APSDCapable[6]=1
- [ 21.820000] APSDCapable[7]=1
- [ 21.828000] APSDCapable[8]=1
- [ 21.832000] APSDCapable[9]=1
- [ 21.840000] APSDCapable[10]=1
- [ 21.844000] APSDCapable[11]=1
- [ 21.852000] APSDCapable[12]=1
- [ 21.856000] APSDCapable[13]=1
- [ 21.864000] APSDCapable[14]=1
- [ 21.868000] APSDCapable[15]=1
- [ 21.876000] default ApCliAPSDCapable[0]=1
- [ 21.884000] default ApCliAPSDCapable[1]=1
- [ 22.092000] Key1Str is Invalid key length(0) or Type(0)
- [ 22.100000] Key2Str is Invalid key length(0) or Type(0)
- [ 22.112000] Key3Str is Invalid key length(0) or Type(0)
- [ 22.124000] Key4Str is Invalid key length(0) or Type(0)
- [ 22.160000] RTMPSetDefaultChannel() : default channel to 1
- [ 22.168000] load fw image from fw_header_image
- [ 22.180000] AndesMTLoadFwMethod1(2174)::pChipCap->fw_len(63056)
- [ 22.192000] FW Version:_e2_mp
- [ 22.196000] FW Build Date:20150211175503
- [ 22.204000] CmdAddressLenReq:(ret = 0)
- [ 22.212000] CmdFwStartReq: override = 1, address = 1048576
- [ 22.224000] CmdStartDLRsp: WiFI FW Download Success
- [ 22.420000] MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
- [ 22.432000] efuse_probe: efuse = 10000002
- [ 22.440000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
- [ 22.452000] RtmpEepromGetDefault::e2p_dafault=2
- [ 22.460000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
- [ 22.476000] NVM is FLASH mode
- [ 22.480000] 1. Phy Mode = 14
- [ 22.608000] br-lan: port 1(eth0.1) entered forwarding state
- [ 22.648000] Country Region from e2p = ffff
- [ 22.660000] tssi_1_target_pwr_g_band = 34
- [ 22.668000] 2. Phy Mode = 14
- [ 22.672000] 3. Phy Mode = 14
- [ 22.680000] NICInitPwrPinCfg(11): Not support for HIF_MT yet!
- [ 22.688000] NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
- [ 22.704000] mt_mac_init()-->
- [ 22.712000] MtAsicInitMac()-->
- [ 22.716000] mt7628_init_mac_cr()-->
- [ 22.724000] MtAsicSetMacMaxLen(1241): Set the Max RxPktLen=1024!
- [ 22.736000] <--mt_mac_init()
- [ 22.744000] WTBL Segment 1 info:
- [ 22.748000] MemBaseAddr/FID:0x28000/0
- [ 22.756000] EntrySize/Cnt:32/128
- [ 22.764000] WTBL Segment 2 info:
- [ 22.772000] MemBaseAddr/FID:0x40000/0
- [ 22.776000] EntrySize/Cnt:64/128
- [ 22.784000] WTBL Segment 3 info:
- [ 22.792000] MemBaseAddr/FID:0x42000/64
- [ 22.800000] EntrySize/Cnt:64/128
- [ 22.804000] WTBL Segment 4 info:
- [ 22.812000] MemBaseAddr/FID:0x44000/128
- [ 22.820000] EntrySize/Cnt:32/128
- [ 22.828000] AntCfgInit(2876): Not support for HIF_MT yet!
- [ 22.840000] MCS Set = ff ff 00 00 01
- [ 22.844000] MtAsicSetChBusyStat(826): Not support for HIF_MT yet!
- [ 23.164000] CmdSlotTimeSet:(ret = 0)
- [ 25.528000] [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
- [ 25.540000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
- [ 25.552000] MtAsicSetRalinkBurstMode(2919): Not support for HIF_MT yet!
- [ 25.564000] MtAsicSetPiggyBack(763): Not support for HIF_MT yet!
- [ 25.648000] MtAsicSetTxPreamble(2898): Not support for HIF_MT yet!
- [ 25.664000] MtAsicAddSharedKeyEntry(1308): Not support for HIF_MT yet!
- [ 25.676000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
- [ 25.688000] Main bssid = 8c:88:2b:00:00:0c
- [ 25.696000] <==== rt28xx_init, Status=0
- [ 25.716000] mt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f
- [ 25.732000] WiFi Startup Cost (ra0): 4.020s
- [ 26.912000] device ra0 entered promiscuous mode
- [ 26.924000] br-lan: port 2(ra0) entered forwarding state
- [ 26.932000] br-lan: port 2(ra0) entered forwarding state
- [ 28.936000] br-lan: port 2(ra0) entered forwarding state
- BusyBox v1.22.1 (2018-07-23 19:27:47 PDT) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- BARRIER BREAKER (Barrier Breaker, unknown)
- -----------------------------------------------------
- * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement