Rocinante Printing Guide

# Rocinante Printing Guide
Model by Martin: https://www.prusaprinters.org/prints/136343-rocinante-from-expanse

The segments are according to the assembly animation video: https://www.youtube.com/watch?v=s8EBRozAoQU

### Notes
* The `xxx_-_leg_pins_4x11_5.stl` file in the Segment 2 folder is actually only needed in segment 3
* You need 9 10x10 pins in segment 1, the file for those is `xxx_-_pin_10x10_2x.stl` in the Segment 2 folder.
* The model has a total of 238 parts.

## 6 PDCs (14 parts per PDC)
* 6x `xxx_-_pdc2.stl`
* 6x `xxx_-_pdc_cannon.stl`
* 6x `xxx_-_pdc.stl`
* 6x `xxx_-_roci_frame_cov.stl`
* 12x `xxx_-_pdc_covering.stl`
* 12x `xxx_-_pdc_filler.stl`
* 6x `xxx_-_pdc_cannon2.stl`
* 6x `xxx_-_pin_3x6.stl`
* 6x `xxx_-_leg_pin_4x8.stl`
* 6x `xxx_-_pdc_mag1.stl`
* 6x `xxx_-_roci_pdc_frame.stl`
* 6x `xxx_-_pdc_mag2.stl`

## Air Bridge (8 parts, including the 4 stoppers)
* `xxx_-_bridge2.stl`
* `xxx_-_roci_stoper.stl` (includes 4 stoppers on a raft)
* `xxx_-_roci_airlock.stl`
* `xxx_-_bridge3.stl`
* `xxx_-_bridge1.stl`

## Segment 1 (22 parts, including the 4 antenna parts and the stand)
* `xxx_-_roci_d.stl`
* `xxx_-_roci_covering.stl`
* `xxx_-_roci_b.stl`
* `xxx_-_roci_f.stl`
* `xxx_-_roci_antenna.stl` (includes the 4 antenna parts)
* `xxx_-_roci_e.stl`
* `xxx_-_roci_a.stl`
* `xxx_-_roci.stl`
* `xxx_-_roci_c.stl`
* `xxx_-_roci_stand.stl` (not shown in the animation at this point, just place it aside)
* `xxx_-_pin_10x10_2x.stl` (you need 9 single pins, the file contains 15 pins; the file is in the Segment 2 folder)


## Segment 2 (53 parts, including the 34 10x10 pins and the 1 15x29 pin)
* 2x `xxx_-_pin_10x10_2x.stl` (you need 34 single pins, the file contains 15 pins. Take 4 pins from the pins you printed for segment 1)
* `xxx_-_pin15x29.stl`
* `xxx_-_roci2f.stl`
* `xxx_-_roci2d.stl`
* 4x `xxx_-_roci2c.stl`
* 2x `xxx_-_roci2a.stl`
* `xxx_-_roci2b.stl`
* 2x `xxx_-_roci2e.stl`
* `xxx_m_roci2b.stl`
* `xxx_-_roci2g.stl`


## Segment 3 (4*13 + 19 = 71 parts, including the landing legs)
* 4x `xxx_-_leg_nob_4x.stl`
* 4x `xxx_-_roci_support_4x.stl`
* 4x `xxx_-_roci3b_4x.stl`
* `xxx_-_roci3.stl`
* 4x `xxx_-_roci_support_a_4x.stl`
* `xxx_-_roci3a.stl`
* `xxx_-_roci3c.stl`

### 4 Landing Legs (13 parts per leg)
* `xxx_-_leg_pin_4x7_5.stl` (the file contains all 16 pins needed for the four legs)
* 12x `xxx_-_leg_link1_12x.stl` (3 per leg)
* 4x `xxx_-_leg_foot_4x.stl`
* 4x `xxx_-_leg_base_4x.stl`
* `xxx_-_leg_pin_4x11_5.stl` (the file contains all 12 pins needed for the four legs; from the Segment 2 folder)
* `xxx_-_leg_joint_4x.stl`


## TLDR
Print every file once, except those files:
* 6x `xxx_-_pdc2.stl`
* 6x `xxx_-_pdc_cannon.stl`
* 6x `xxx_-_pdc.stl`
* 6x `xxx_-_roci_frame_cov.stl`
* 12x `xxx_-_pdc_covering.stl`
* 12x `xxx_-_pdc_filler.stl`
* 6x `xxx_-_pdc_cannon2.stl`
* 6x `xxx_-_pin_3x6.stl`
* 6x `xxx_-_leg_pin_4x8.stl`
* 6x `xxx_-_pdc_mag1.stl`
* 6x `xxx_-_roci_pdc_frame.stl`
* 6x `xxx_-_pdc_mag2.stl`
* 3x `xxx_-_pin_10x10_2x.stl` (you will have 2 pins leftover at the end)
* 4x `xxx_-_leg_nob_4x.stl`
* 4x `xxx_-_roci_support_4x.stl`
* 4x `xxx_-_roci3b_4x.stl`
* 4x `xxx_-_roci_support_a_4x.stl`
* 12x `xxx_-_leg_link1_12x.stl` (3 per leg)
* 4x `xxx_-_leg_foot_4x.stl`
* 4x `xxx_-_leg_base_4x.stl`
* 4x `xxx_-_roci2c.stl`
* 2x `xxx_-_roci2a.stl`
* 2x `xxx_-_roci2e.stl`