Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
- Copyright (C) 2000-2009 Broadcom Corporation.
- Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
- Total Flash size: 8192K with 135 sectors
- Chip ID: BCM6368B2, MIPS: 400MHz
- Main Thread: TP0
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-14) : 96368M-1341N
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 64:68:0c:
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 0
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80010000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80010000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 0 buffers found.
- Closing DMA Channels.
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.9.11 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12
- r37793) ) #2 SMP Fri Aug 16 00:39:06 CEST 2013
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368M-1341N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6496 r8192 d13984 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=
- ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] __ex_table already sorted, skipping sort
- [ 0.000000] Memory: 61276k/65536k available (2501k kernel code, 4260k reserved, 593k data, 232k i
- nit, 0k highmem)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.044000] SMP: Booting CPU1...
- [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.080000] SMP: CPU1 is running
- [ 0.080000] Brought up 2 CPUs
- [ 0.112000] NET: Registered protocol family 16
- [ 0.120000] registering PCI controller with io_map_base unset
- [ 0.140000] bio: create slab <bio-0> at 0
- [ 0.144000] PCI host bridge to bus 0000:00
- [ 0.148000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.156000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.164000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.188000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
- [ 0.196000] Switching to clocksource MIPS
- [ 0.204000] NET: Registered protocol family 2
- [ 0.212000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.216000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.224000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.232000] TCP: reno registered
- [ 0.232000] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.240000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.248000] NET: Registered protocol family 1
- [ 0.252000] audit: initializing netlink socket (disabled)
- [ 0.260000] type=2000 audit(0.260:1): initialized
- [ 0.264000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.272000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_NONE) (c) 2001-2006 Red Hat
- , Inc.
- [ 0.280000] msgmni has been set to 119
- [ 0.288000] io scheduler noop registered
- [ 0.292000] io scheduler deadline registered (default)
- Ê[ 0.304000] console [ttyS0] enabled, bootconsole disabled= 10) is a bcm63xx_uart
- [ 0.304000] console [ttyS0] enabled, bootconsole disabled
- [ 0.316000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.324000] physmap platform flash device: 08000000 at 18000000
- [ 0.332000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2
- Chip ID 0x0022cb
- [ 0.344000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.348000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.352000] number of CFI chips: 1
- [ 0.356000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
- [ 0.364000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.372000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
- [ 0.380000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 6d0000
- [ 0.384000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 0.392000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 0.400000] bcm63xxpart: Spare partition is offset 3f0004 and length 3ffffc
- [ 0.408000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 0.416000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 0.420000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.428000] 0x000000010100-0x000000120000 : "kernel"
- [ 0.432000] mtd: partition "kernel" must either start or end on erase block boundary or be smalle
- r than an erase block -- forcing read-only
- [ 0.448000] 0x000000120000-0x0000007f0000 : "rootfs"
- [ 0.456000] mtd: partition "rootfs" set to be root filesystem
- [ 0.460000] mtd: partition "rootfs_data" created automatically, ofs=3F0000, len=400000
- [ 0.468000] 0x0000003f0000-0x0000007f0000 : "rootfs_data"
- [ 0.476000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 0.484000] 0x000000010000-0x0000007f0000 : "linux"
- [ 0.492000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 0.540000] b53_common: found switch: BCM63xx, rev 0
- [ 0.544000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.556000] TCP: cubic registered
- [ 0.560000] NET: Registered protocol family 17
- [ 0.564000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.576000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.584000] Freeing unused kernel memory: 232k freed
- procd: Console is alive
- procd: - watchdog -
- [ 2.660000] SCSI subsystem initialized
- [ 2.804000] usbcore: registered new interface driver usbfs
- [ 2.808000] usbcore: registered new interface driver hub
- [ 2.816000] usbcore: registered new device driver usb
- [ 2.900000] Button Hotplug driver version 0.4.1
- [ 3.700000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.708000] ehci-platform: EHCI generic platform driver
- [ 3.816000] ehci-platform ehci-platform: EHCI Host Controller
- [ 3.820000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 3.828000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 3.848000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 3.856000] hub 1-0:1.0: USB hub found
- [ 3.860000] hub 1-0:1.0: 2 ports detected
- [ 3.872000] Initializing USB Mass Storage driver...
- [ 3.880000] usbcore: registered new interface driver usb-storage
- [ 3.884000] USB Mass Storage support registered.
- [ 3.892000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
- procd: - preinit -
- ifconfig: SIOCGIFFLAGS: No such device
- Press the [f] key and hit [enter] to enter failsafe mode
- mount_root: jffs2 is not ready - marker found
- ifconfig: SIOCGIFFLAGS: No such device
- procd: - early -
- procd: - watchdog -
- procd: - init -
- Please press Enter to activate this console.
- [ 9.928000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
- [ 9.936000] Backport generated by backports.git backports-20130617-4-ge3220f5
- [ 9.976000] cfg80211: Calling CRDA to update world regulatory domain
- [ 9.996000] cfg80211: World regulatory domain updated:
- [ 10.000000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 10.008000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.016000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.024000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.032000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.040000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.228000] NET: Registered protocol family 10
- [ 11.032000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 12.620000] cfg80211: Calling CRDA for country: AW
- [ 12.624000] cfg80211: Regulatory domain changed to country: AW
- [ 12.632000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 12.632000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc03a0000, irq=21
- [ 12.648000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.652000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.660000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.668000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
- [ 12.984000] PPP generic driver version 2.4.2
- [ 13.216000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.240000] xt_time: kernel timezone is -0000
- [ 13.444000] NET: Registered protocol family 24
- [ 13.456000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
- [ 14.328000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 19.624000] device eth0.1 entered promiscuous mode
- [ 19.628000] device eth0 entered promiscuous mode
- [ 19.636000] br-lan: port 1(eth0.1) entered forwarding state
- [ 19.640000] br-lan: port 1(eth0.1) entered forwarding state
- [ 20.616000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
- [ 21.644000] br-lan: port 1(eth0.1) entered forwarding state
- [ 30.836000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
- [ 30.852000] jffs2_build_filesystem(): unlocking the mtd device... done.
- [ 30.856000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
- [ 64.912000] jffs2: notice: (856) jffs2_build_xattr_subsystem: complete building xattr subsystem,
- 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- procd: - init complete -
- [ 426.620000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
- [ 503.272000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 503.352000] device wlan0 entered promiscuous mode
- [ 503.376000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 503.412000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 503.420000] br-lan: port 2(wlan0) entered forwarding state
- [ 503.428000] br-lan: port 2(wlan0) entered forwarding state
- [ 505.432000] br-lan: port 2(wlan0) entered forwarding state
- [ 508.648000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 510.300000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 511.940000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 516.964000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 524.060000] IPv6: ADDRCONF(NETDEV_UP): tmp.wlan0: link is not ready
- [ 566.600000] br-lan: port 2(wlan0) entered disabled state
- [ 566.604000] br-lan: port 1(eth0.1) entered disabled state
- [ 566.616000] device eth0.1 left promiscuous mode
- [ 566.620000] device eth0 left promiscuous mode
- [ 566.624000] br-lan: port 1(eth0.1) entered disabled state
- [ 566.668000] device wlan0 left promiscuous mode
- [ 566.672000] br-lan: port 2(wlan0) entered disabled state
- [ 566.748000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port3, 100Mbps, full-duplex
- [ 566.776000] device eth0.1 entered promiscuous mode
- [ 566.780000] device eth0 entered promiscuous mode
- [ 566.796000] device wlan0 entered promiscuous mode
- [ 566.808000] br-lan: port 2(wlan0) entered forwarding state
- [ 566.812000] br-lan: port 2(wlan0) entered forwarding state
- [ 566.820000] br-lan: port 1(eth0.1) entered forwarding state
- [ 566.824000] br-lan: port 1(eth0.1) entered forwarding state
- [ 567.016000] device wlan0 left promiscuous mode
- [ 567.020000] br-lan: port 2(wlan0) entered disabled state
- [ 567.612000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
- [ 568.216000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 568.828000] br-lan: port 1(eth0.1) entered forwarding state
- [ 570.448000] wlan0: authenticate with 00:13:f7:
- [ 570.468000] wlan0: send auth to 00:13:f7: (try 1/3)
- [ 570.476000] wlan0: authenticated
- [ 570.484000] wlan0: associate with 00:13:f7: (try 1/3)
- [ 570.492000] wlan0: RX AssocResp from 00:13: (capab=0x411 status=0 aid=2)
- [ 570.504000] wlan0: associated
- [ 570.504000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- BusyBox v1.19.4 (2013-08-16 00:11:28 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- ---------------------------------------------
- BARRIER BREAKER (Bleeding Edge, r37793)
- -----------------------------------------------------
- * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/# ls /etc/config
- 6relayd dropbear fstab network ucitrack wireless
- dhcp firewall luci system uhttpd
- root@OpenWrt:/# ls /overlay/etc/config
- 6relayd dropbear fstab network ucitrack wireless
- dhcp firewall luci system uhttpd
- root@OpenWrt:/# reboot
- procd: - shutdown -
- root@OpenWrt:/# [ 7396.356000] br-lan: port 1(eth0.1) entered disabled state
- [ 7396.364000] device eth0.1 left promiscuous mode
- [ 7396.368000] device eth0 left promiscuous mode
- [ 7396.376000] br-lan: port 1(eth0.1) entered disabled state
- [ 7396.976000] wlan0: deauthenticating from 00:13:f7: by local choice (reason=3)
- procd: - reboot -
- [ 7397.408000] Restarting system.
- Ê 7397.412000] triggering watchdog soft-reset...
- CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE)
- Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com)
- Copyright (C) 2000-2009 Broadcom Corporation.
- Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
- Total Flash size: 8192K with 135 sectors
- Chip ID: BCM6368B2, MIPS: 400MHz
- Main Thread: TP0
- Total Memory: 67108864 bytes (64MB)
- Boot Address: 0xb8000000
- Board IP address : 192.168.1.1:ffffff00
- Host IP address : 192.168.1.100
- Gateway IP address :
- Run from flash/host (f/h) : f
- Default host run file name : vmlinux
- Default host flash file name : bcm963xx_fs_kernel
- Boot delay (0-9 seconds) : 1
- Board Id (0-14) : 96368M-1341N
- Number of MAC Addresses (1-32) : 11
- Base MAC Address : 64:68:0c:
- PSI Size (1-64) KBytes : 24
- Enable Backup PSI [0|1] : 0
- System Log Size (0-256) KBytes : 0
- Main Thread Number [0|1] : 0
- *** Press any key to stop auto run (1 seconds) ***
- Auto run second count down: 0
- Booting from only image (0xb8010000) ...
- Code Address: 0x80010000, Entry Address: 0x80010000
- LZMA: Prossible old LZMA format, trying to decompress..
- Decompression OK!
- Entry at 0x80010000
- Closing network.
- Disabling Switch ports.
- Flushing Receive Buffers...
- 0 buffers found.
- Closing DMA Channels.
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.9.11 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12
- r37793) ) #2 SMP Fri Aug 16 00:39:06 CEST 2013
- [ 0.000000] Detected Broadcom 0x6368 CPU revision b2
- [ 0.000000] CPU frequency is 400 MHz
- [ 0.000000] 64MB of RAM installed
- [ 0.000000] registering 38 GPIOs
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22-1
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 96368M-1341N
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 04000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x03ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6496 r8192 d13984 u32768
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=
- ttyS0,115200
- [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
- [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] __ex_table already sorted, skipping sort
- [ 0.000000] Memory: 61276k/65536k available (2501k kernel code, 4260k reserved, 593k data, 232k i
- nit, 0k highmem)
- [ 0.000000] Hierarchical RCU implementation.
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
- [ 0.032000] pid_max: default: 32768 minimum: 301
- [ 0.036000] Mount-cache hash table entries: 512
- [ 0.044000] SMP: Booting CPU1...
- [ 0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
- [ 0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.080000] SMP: CPU1 is running
- [ 0.080000] Brought up 2 CPUs
- [ 0.112000] NET: Registered protocol family 16
- [ 0.120000] registering PCI controller with io_map_base unset
- [ 0.136000] bio: create slab <bio-0> at 0
- [ 0.144000] PCI host bridge to bus 0000:00
- [ 0.148000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
- [ 0.156000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff]
- [ 0.164000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
- [ 0.188000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff]
- [ 0.196000] Switching to clocksource MIPS
- [ 0.204000] NET: Registered protocol family 2
- [ 0.208000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.216000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
- [ 0.224000] TCP: Hash tables configured (established 512 bind 512)
- [ 0.228000] TCP: reno registered
- [ 0.232000] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.240000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 0.244000] NET: Registered protocol family 1
- [ 0.252000] audit: initializing netlink socket (disabled)
- [ 0.260000] type=2000 audit(0.260:1): initialized
- [ 0.264000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.272000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_NONE) (c) 2001-2006 Red Hat
- , Inc.
- [ 0.280000] msgmni has been set to 119
- [ 0.284000] io scheduler noop registered
- [ 0.288000] io scheduler deadline registered (default)
- Š[ 0.304000] console [ttyS0] enabled, bootconsole disabled= 10) is a bcm63xx_uart
- [ 0.304000] console [ttyS0] enabled, bootconsole disabled
- [ 0.316000] bcm63xx-rng bcm63xx-rng: registered RNG driver
- [ 0.324000] physmap platform flash device: 08000000 at 18000000
- [ 0.332000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2
- Chip ID 0x0022cb
- [ 0.340000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.348000] Amd/Fujitsu Extended Query version 1.1.
- [ 0.352000] number of CFI chips: 1
- [ 0.356000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N
- [ 0.364000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.372000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
- [ 0.376000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 6d0000
- [ 0.384000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
- [ 0.392000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
- [ 0.400000] bcm63xxpart: Spare partition is offset 3f0004 and length 3ffffc
- [ 0.408000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
- [ 0.412000] Creating 5 MTD partitions on "physmap-flash.0":
- [ 0.420000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.428000] 0x000000010100-0x000000120000 : "kernel"
- [ 0.432000] mtd: partition "kernel" must either start or end on erase block boundary or be smalle
- r than an erase block -- forcing read-only
- [ 0.448000] 0x000000120000-0x0000007f0000 : "rootfs"
- [ 0.452000] mtd: partition "rootfs" set to be root filesystem
- [ 0.460000] mtd: partition "rootfs_data" created automatically, ofs=3F0000, len=400000
- [ 0.468000] 0x0000003f0000-0x0000007f0000 : "rootfs_data"
- [ 0.476000] 0x0000007f0000-0x000000800000 : "nvram"
- [ 0.484000] 0x000000010000-0x0000007f0000 : "linux"
- [ 0.492000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542)
- [ 0.536000] b53_common: found switch: BCM63xx, rev 0
- [ 0.540000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.552000] TCP: cubic registered
- [ 0.556000] NET: Registered protocol family 17
- [ 0.560000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.572000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.584000] Freeing unused kernel memory: 232k freed
- procd: Console is alive
- procd: - watchdog -
- [ 2.676000] SCSI subsystem initialized
- [ 2.816000] usbcore: registered new interface driver usbfs
- [ 2.820000] usbcore: registered new interface driver hub
- [ 2.828000] usbcore: registered new device driver usb
- [ 2.908000] Button Hotplug driver version 0.4.1
- [ 3.712000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.720000] ehci-platform: EHCI generic platform driver
- [ 3.828000] ehci-platform ehci-platform: EHCI Host Controller
- [ 3.832000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
- [ 3.840000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500
- [ 3.860000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
- [ 3.868000] hub 1-0:1.0: USB hub found
- [ 3.872000] hub 1-0:1.0: 2 ports detected
- [ 3.884000] Initializing USB Mass Storage driver...
- [ 3.892000] usbcore: registered new interface driver usb-storage
- [ 3.896000] USB Mass Storage support registered.
- [ 3.904000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
- procd: - preinit -
- ifconfig: SIOCGIFFLAGS: No such device
- Press the [f] key and hit [enter] to enter failsafe mode
- [ 7.540000] jffs2: notice: (237) jffs2_build_xattr_subsystem: complete building xattr subsystem,
- 1 of xdatum (0 unchecked, 0 orphan) and 11 of xref (0 dead, 2 orphan) found.
- mount_root: jffs2 is ready
- [ 7.584000] jffs2: notice: (234) jffs2_build_xattr_subsystem: complete building xattr subsystem,
- 1 of xdatum (0 unchecked, 0 orphan) and 11 of xref (0 dead, 2 orphan) found.
- ifconfig: SIOCGIFFLAGS: No such device
- procd: - early -
- procd: - watchdog -
- procd: - init -
- Please press Enter to activate this console.
- [ 10.004000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
- [ 10.012000] Backport generated by backports.git backports-20130617-4-ge3220f5
- [ 10.036000] cfg80211: Calling CRDA to update world regulatory domain
- [ 10.052000] cfg80211: World regulatory domain updated:
- [ 10.056000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 10.064000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.072000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.080000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 10.088000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.096000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 10.340000] NET: Registered protocol family 10
- [ 11.124000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
- [ 12.712000] cfg80211: Calling CRDA for country: AW
- [ 12.716000] cfg80211: Regulatory domain changed to country: AW
- [ 12.724000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 12.724000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xc03a0000, irq=21
- [ 12.736000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.744000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.752000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
- [ 12.760000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
- [ 13.060000] PPP generic driver version 2.4.2
- [ 13.292000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.316000] xt_time: kernel timezone is -0000
- [ 13.520000] NET: Registered protocol family 24
- [ 13.532000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
- [ 14.400000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- procd: - init complete -
- BusyBox v1.19.4 (2013-08-16 00:11:28 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- ---------------µjjjjjjjjjjjjjjjjjjjjjjjjjjjj’”(*ªRQ© BREAKER (Bleeding Edge, r37793)
- -----------------------------------------------------
- * 1/2 oz Galliano Pour all ingredients into
- * 4 oz cold Coffee an irish coffee mug filled
- * 1 1/2 oz Dark Rum with crushed ice. Stir.
- * 2 tsp. Creme de Cacao
- -----------------------------------------------------
- root@OpenWrt:/# cat /etc/config/reressss
- config wifi-device 'radio0'
- option type 'mac80211'
- option channel '11'
- option hwmode '11ng'
- option path 'pci0000:00/0000:00:01.0'
- option htmode 'HT20'
- list ht_capab 'SHORT-GI-40'
- list ht_capab 'TX-STBC'
- list ht_capab 'RX-STBC1'
- list ht_capab 'DSSS_CCK-40'
- option disabled '0'
- option txpower '20'
- option country 'AW'
- config wifi-iface
- option network 'wwan'
- option ssid 'WLAN_69'
- option encryption 'psk2'
- option device 'radio0'
- option mode 'sta'
- option bssid '00:13:F7:
- option key 'X000138CB5169'
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement