2021-09-11 06:45:52 driver/thread.c:3055:create_restart_monitor_thread: create thread
2021-09-11 06:45:52 Read tune config: tune_profile=6, tune_status=2, tune_frequency=550, tune_voltage=1940, tune_freq_step=10, tune_volt_step=10, tune_max_frequency=575, tune_power=2870, tune_bad_domains_threshold=1, tune_max_voltage=1940, tune_freq_yellow_step=10, tune_max_restarts=7, tune_restarts=2, voltage_increase=20, voltage_pre_heat_delay=240, tune_decrease_voltage_mode=-1, tune_uptime=360, tune_chain_statuses=1, tune_bad_freq_step=25, tune_one_chain_freq_increased=-1, bad 50
, 1
2021-09-11 06:45:52 driver/driver-btm-api.c:294:init_freq_mode: This is scan-user version
2021-09-11 06:45:52 driver/driver-btm-api.c:2477:bitmain_soc_init: opt_multi_version     = 1
2021-09-11 06:45:52 driver/driver-btm-api.c:2478:bitmain_soc_init: opt_bitmain_ab        = 1
2021-09-11 06:45:52 driver/driver-btm-api.c:2479:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-09-11 06:45:52 driver/driver-btm-api.c:2480:bitmain_soc_init: Miner compile time: Mon Jun 14 19:48:14 MSK 2021 type: Antminer S17+ v1.2.4
2021-09-11 06:45:52 driver/driver-btm-api.c:2482:bitmain_soc_init: commit version: daa20d7 2021-06-03 13:13:12, build by: root 2021-06-19 12:45:26
2021-09-11 06:45:52 driver/driver-btm-api.c:1896:show_sn: 8028cd242b10481c
2021-09-11 06:45:52 driver/driver-btm-api.c:1904:show_sn: no SN got, please write SN to /nvdata/sn
2021-09-11 06:45:52 driver/fan.c:220:front_fan_power_on: Note: front fan is power on!
2021-09-11 06:45:52 driver/fan.c:226:rear_fan_power_on: Note: rear fan is power on!
2021-09-11 06:45:52 driver/driver-btm-api.c:1958:miner_device_init: Detect 256MB control board of XILINX
2021-09-11 06:45:52 driver/driver-btm-api.c:1932:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-09-11 06:45:58 driver/driver-btm-api.c:1606:init_miner_version: miner ID : 8028cd242b10481c
2021-09-11 06:45:58 driver/driver-btm-api.c:1611:init_miner_version: FPGA Version = 0xB023
2021-09-11 06:46:03 driver/thread.c:3065:create_read_nonce_reg_thread: create thread
2021-09-11 06:46:03 driver/driver-btm-api.c:1685:bitmain_board_init: product_id[0] = 0
2021-09-11 06:46:03 driver/driver-btm-api.c:1685:bitmain_board_init: product_id[1] = 0
2021-09-11 06:46:03 driver/driver-btm-api.c:1685:bitmain_board_init: product_id[2] = 0
2021-09-11 06:46:03 driver/driver-btm-api.c:1706:bitmain_board_init: project:0
2021-09-11 06:46:03 driver/driver-btm-api.c:1049:dump_pcb_bom_version: Chain [0] PCB Version: 0x0100
2021-09-11 06:46:03 driver/driver-btm-api.c:1050:dump_pcb_bom_version: Chain [0] BOM Version: 0x0100
2021-09-11 06:46:03 driver/driver-btm-api.c:1049:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-09-11 06:46:03 driver/driver-btm-api.c:1050:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-09-11 06:46:03 driver/driver-btm-api.c:1049:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-09-11 06:46:03 driver/driver-btm-api.c:1050:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-09-11 06:46:05 driver/driver-btm-api.c:1740:bitmain_board_init: Fan check passed.
2021-09-11 06:46:06 driver/board.c:31:jump_and_app_check_restore_pic: chain[0] PIC jump to app
2021-09-11 06:46:10 driver/board.c:34:jump_and_app_check_restore_pic: Check chain[0] PIC fw version=0x88
2021-09-11 06:46:10 driver/board.c:31:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-09-11 06:46:15 driver/board.c:34:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2021-09-11 06:46:15 driver/board.c:31:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-09-11 06:46:19 driver/board.c:34:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2021-09-11 06:46:19 driver/thread.c:3060:create_pic_heart_beat_thread: create thread
2021-09-11 06:46:19 driver/power_api.c:228:power_init: power init ...
2021-09-11 06:46:19 driver/power_api.c:304:power_init: highest_voltage    = 21.000000
2021-09-11 06:46:19 driver/power_api.c:305:power_init: working_voltage    = 19.500000
2021-09-11 06:46:19 driver/power_api.c:306:power_init: higher_voltage     = 20.400000
2021-09-11 06:46:19 driver/driver-btm-api.c:1751:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-09-11 06:46:51 driver/driver-btm-api.c:1794:bitmain_board_init: setting to voltage: 21.00 ...
2021-09-11 06:46:51 driver/power_api.c:819:set_to_highest_voltage_by_steps: Set to voltage 21.00, step by step.
2021-09-11 06:47:07 driver/uart.c:49:set_baud: set UART baud to 115200
2021-09-11 06:47:16 driver/driver-btm-api.c:1289:check_asic_number_with_power_on: Chain[0]: find 65 asic, times 0
2021-09-11 06:47:26 driver/driver-btm-api.c:1289:check_asic_number_with_power_on: Chain[1]: find 64 asic, times 0
2021-09-11 06:47:35 driver/driver-btm-api.c:1289:check_asic_number_with_power_on: Chain[1]: find 64 asic, times 1
2021-09-11 06:47:45 driver/driver-btm-api.c:1289:check_asic_number_with_power_on: Chain[1]: find 64 asic, times 2
2021-09-11 06:47:52 driver/driver-btm-api.c:1289:check_asic_number_with_power_on: Chain[1]: find 64 asic, times 3
2021-09-11 06:48:00 driver/driver-btm-api.c:1289:check_asic_number_with_power_on: Chain[1]: find 64 asic, times 4
2021-09-11 06:48:00 driver/driver-btm-api.c:1301:check_asic_number_with_power_on: setting to voltage: 20.50 ...
2021-09-11 06:48:10 driver/driver-btm-api.c:1289:check_asic_number_with_power_on: Chain[1]: find 64 asic, times 5
2021-09-11 06:48:10 driver/driver-btm-api.c:1301:check_asic_number_with_power_on: setting to voltage: 21.00 ...
2021-09-11 06:48:14 driver/driver-btm-api.c:1314:check_asic_number_with_power_on: Chain 1 only find 64 asic, will power off hash board 1
2021-09-11 06:48:14 driver/driver-btm-api.c:1269:check_asic_number_with_power_on: setting to voltage: 21.00 ...
2021-09-11 06:48:14 driver/power_api.c:819:set_to_highest_voltage_by_steps: Set to voltage 21.00, step by step.
2021-09-11 06:48:26 driver/driver-btm-api.c:1289:check_asic_number_with_power_on: Chain[2]: find 65 asic, times 0
2021-09-11 06:48:32 driver/driver-hash-chip.c:107:set_uart_relay: set uart relay to 0x330003
2021-09-11 06:48:32 driver/driver-btm-api.c:1032:set_order_clock: chain[0]: set order clock, stragegy 3
2021-09-11 06:48:32 driver/driver-btm-api.c:1032:set_order_clock: chain[2]: set order clock, stragegy 3
2021-09-11 06:48:32 driver/driver-hash-chip.c:299:set_clock_delay_control: core_data = 0x34
2021-09-11 06:48:32 voltage[0] = 1910
2021-09-11 06:48:32 voltage[2] = 1910
2021-09-11 06:48:32 Highest voltage is 21.00
2021-09-11 06:48:32 driver/power_api.c:318:set_working_voltage: working_voltage = 19.300000
2021-09-11 06:48:34 driver/temperature.c:325:calibrate_temp_sensor_all_chains: chain 0 temp sensor NCT218, offset -8
2021-09-11 06:48:35 driver/temperature.c:325:calibrate_temp_sensor_all_chains: chain 2 temp sensor NCT218, offset -8
2021-09-11 06:48:35 driver/uart.c:49:set_baud: set UART baud to 12000000
2021-09-11 06:48:36 driver/driver-btm-api.c:678:check_bringup_temp: Bring up temperature is 26
2021-09-11 06:48:36 driver/thread.c:3080:create_check_miner_status_thread: create thread
2021-09-11 06:48:36 driver/thread.c:3070:create_set_miner_status_thread: create thread
2021-09-11 06:48:36 driver/thread.c:3095:create_auto_tune_thread: create thread
2021-09-11 06:48:36 driver/thread.c:3100:create_read_real_voltage_thread: create thread
2021-09-11 06:48:36 driver/driver-btm-api.c:2660:bitmain_soc_init: get freq from eeprom
2021-09-11 06:49:01 driver/driver-btm-api.c:1015:set_timeout: freq = 625, percent = 90, hcn = 44236, timeout = 70
2021-09-11 06:49:01 driver/driver-btm-api.c:2681:bitmain_soc_init: check fixup
2021-09-11 06:49:01 driver/power_api.c:813:set_to_working_voltage_by_steps: Set to voltage 19.30, step by step.
2021-09-11 06:49:07 driver/power_api.c:536:get_average_voltage: average_voltage = 19.290662
2021-09-11 06:49:07 driver/thread.c:3050:create_temperature_monitor_thread: create thread
2021-09-11 06:49:07 driver/thread.c:3075:create_check_system_status_thread: create thread
2021-09-11 06:49:07 driver/thread.c:3087:create_read_hash_rate_thread: create thread
2021-09-11 06:49:08 driver/driver-btm-api.c:2749:bitmain_soc_init: Init done!
2021-09-11 06:49:08 driver/driver-btm-api.c:210:set_miner_status: STATUS_INIT
2021-09-11 06:49:08 driver/driver-btm-api.c:210:set_miner_status: STATUS_OKAY
2021-09-11 06:49:13 driver/driver-btm-api.c:2993:dhash_chip_send_job: Version num 4
2021-09-11 06:53:13 driver/thread.c:2907:check_system_status_thread: Reduce working voltage from 19.30v to 19.10v
2021-09-11 06:53:13 driver/power_api.c:318:set_working_voltage: working_voltage = 19.200000
2021-09-11 06:53:13 driver/power_api.c:813:set_to_working_voltage_by_steps: Set to voltage 19.20, step by step.
2021-09-11 06:53:19 Got reinit signal
2021-09-11 06:53:19 driver/thread.c:3164:cancel_auto_tune_thread: cancel thread
2021-09-11 06:53:19 Restarting...
2021-09-11 06:53:19 Restart - 1
2021-09-11 06:53:24 Restart - 2
2021-09-11 06:53:28 Restart - 3
2021-09-11 06:53:33 Restart - 4
2021-09-11 06:53:37 driver/power_api.c:318:set_working_voltage: working_voltage = 19.100000
2021-09-11 06:53:37 driver/power_api.c:813:set_to_working_voltage_by_steps: Set to voltage 19.10, step by step.
2021-09-11 06:53:38 Restart - 5
2021-09-11 06:53:43 Restart - 6
2021-09-11 06:53:48 Restart - 7
2021-09-11 06:53:53 Restart - 8
2021-09-11 06:53:58 Restart - 9
2021-09-11 06:54:03 Restart - 10
2021-09-11 06:54:08 Restart - 11
2021-09-11 06:54:13 Restart - 12
2021-09-11 06:54:18 Restart - 13
2021-09-11 06:54:23 Restart - 14
2021-09-11 06:54:28 Restart - 15
2021-09-11 06:54:34 Restart - 16
2021-09-11 06:54:39 Restart - 17
2021-09-11 06:54:45 Restart - 18
2021-09-11 06:54:51 Restart - 19
2021-09-11 06:54:57 Restart - 20
2021-09-11 06:55:03 Restart - 21
2021-09-11 06:55:10 Restart - 22
2021-09-11 06:55:17 Restart - 23
2021-09-11 06:55:24 Restart - 24
2021-09-11 06:56:03 LOST RATE ON CHAIN 3
2021-09-11 06:56:13 REGAINED RATE ON CHAIN 3