Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Texas Instruments X-Loader 1.4.4ss (Mar 6 2011 - 20:56:33)
- Beagle xM Rev A
- Reading boot sector
- Loading u-boot.bin from mmc
- U-Boot 2010.12 (Mar 06 2011 - 20:57:07)
- OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
- OMAP3 Beagle board + LPDDR/NAND
- I2C: ready
- DRAM: 512 MiB
- NAND: 0 MiB
- MMC: OMAP SD/MMC: 0
- *** Warning - readenv() failed, using default environment
- In: serial
- Out: serial
- Err: serial
- Beagle xM Rev A
- No EEPROM on expansion board
- Die ID #437a00011ff00000015739eb0c01701a
- Hit any key to stop autoboot: 0
- reading boot.scr
- ** Unable to read "boot.scr" from mmc 0:1 **
- reading uImage
- 2908412 bytes read
- Booting from mmc ...
- ## Booting kernel from Legacy Image at 82000000 ...
- Image Name: Angstrom/2.6.36/omap3-multi
- Image Type: ARM Linux Kernel Image (uncompressed)
- Data Size: 2908348 Bytes = 2.8 MiB
- Load Address: 80008000
- Entry Point: 80008000
- Verifying Checksum ... OK
- Loading Kernel Image ... OK
- OK
- Starting kernel ...
- Uncompressing Linux... done, booting the kernel.
- Linux version 2.6.36 (steve@build.sakoman.com) (gcc version 4.3.3 (GCC) ) #1 Sun Mar 6
- 21:12:27 PST 2011
- CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
- CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
- Machine: OMAP3 Beagle Board
- Reserving 12582912 bytes SDRAM for VRAM
- Memory policy: ECC disabled, Data cache writeback
- OMAP3630 ES1.1 (l2cache iva sgx neon isp 192mhz_clk )
- SRAM: Mapped pa 0x40208000 to va 0xfe408000 size: 0x8000
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 126976
- Kernel command line: console=ttyS2,115200n8 mpurate=800 vram=12M
- omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw
- rootfstype=ext3 rootwait
- PID hash table entries: 2048 (order: 1, 8192 bytes)
- Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- Memory: 500MB = 500MB total
- Memory: 501492k/501492k available, 22796k reserved, 0K highmem
- Virtual kernel memory layout:
- vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
- vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
- lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
- modules : 0xbf000000 - 0xc0000000 ( 16 MB)
- .init : 0xc0008000 - 0xc0031000 ( 164 kB)
- .text : 0xc0031000 - 0xc054f000 (5240 kB)
- .data : 0xc0574000 - 0xc05af280 ( 237 kB)
- Hierarchical RCU implementation.
- RCU-based detection of stalled CPUs is disabled.
- Verbose stalled-CPUs detection is disabled.
- NR_IRQS:402
- Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
- Reprogramming SDRC clock to 332000000 Hz
- GPMC revision 5.0
- IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
- Total of 96 interrupts on 1 active controller
- OMAP GPIO hardware version 2.5
- OMAP clockevent source: GPTIMER12 at 32768 Hz
- Console: colour dummy device 80x30
- Calibrating delay loop... 501.02 BogoMIPS (lpj=1957888)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- CPU: Testing write buffer coherency: ok
- devtmpfs: initialized
- regulator: core version 0.5
- NET: Registered protocol family 16
- Found NAND on CS0
- Registering NAND on CS0
- Switched to new clocking rate (Crystal/Core/MPU): 26.0/800/332 MHz
- OMAP DMA hardware revision 5.0
- bio: create slab <bio-0> at 0
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz
- twl4030: PIH (irq 7) chaining IRQs 368..375
- twl4030: power (irq 373) chaining IRQs 376..383
- twl4030: gpio (irq 368) chaining IRQs 384..401
- regulator: VUSB1V5: 1500 mV normal standby
- regulator: VUSB1V8: 1800 mV normal standby
- regulator: VUSB3V1: 3100 mV normal standby
- twl4030_usb twl4030_usb: Initialized TWL4030 USB module
- regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
- regulator: VDAC: 1800 mV normal standby
- regulator: VDVI: 1800 mV normal standby
- regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
- i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
- i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz
- Advanced Linux Sound Architecture Driver Version 1.0.23.
- Bluetooth: Core ver 2.15
- NET: Registered protocol family 31
- Bluetooth: HCI device and connection manager initialized
- Bluetooth: HCI socket layer initialized
- cfg80211: Calling CRDA to update world regulatory domain
- Switching to clocksource 32k_counter
- musb_hdrc: version 6.0, musb-dma, host, debug=0
- musb_hdrc musb_hdrc: MUSB HDRC host driver
- musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
- usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb1: Product: MUSB HDRC host driver
- usb usb1: Manufacturer: Linux 2.6.36 musb-hcd
- usb usb1: SerialNumber: musb_hdrc
- hub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- musb_hdrc musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
- NET: Registered protocol family 2
- IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
- TCP established hash table entries: 16384 (order: 5, 131072 bytes)
- TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
- TCP: Hash tables configured (established 16384 bind 16384)
- TCP reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
- VFS: Disk quotas dquot_6.5.2
- Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
- msgmni has been set to 979
- Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
- io scheduler noop registered
- io scheduler deadline registered
- io scheduler cfq registered (default)
- OMAP DSS rev 2.0
- OMAP DISPC rev 3.0
- OMAP VENC rev 2
- OMAP DSI rev 1.0
- Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
- serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
- serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
- serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
- console [ttyS2] enabled
- serial8250.3: ttyS3 at MMIO 0x49042000 (irq = 70) is a ST16654
- brd: module loaded
- loop: module loaded
- omap2-nand driver initializing
- No NAND device found.
- No NAND device found.
- usbcore: registered new interface driver asix
- usbcore: registered new interface driver cdc_ether
- ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
- ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
- ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
- ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
- usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
- usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb2: Product: OMAP-EHCI Host Controller
- usb usb2: Manufacturer: Linux 2.6.36 ehci_hcd
- usb usb2: SerialNumber: ehci-omap.0
- hub 2-0:1.0: USB hub found
- hub 2-0:1.0: 3 ports detected
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- mice: PS/2 mouse device common for all mice
- input: gpio-keys as /devices/platform/gpio-keys/input/input0
- twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
- twl_rtc twl_rtc: Power up reset detected.
- twl_rtc twl_rtc: Enabling TWL-RTC.
- i2c /dev entries driver
- OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
- Bluetooth: HCI UART driver ver 2.2
- Bluetooth: HCI H4 protocol initialized
- Bluetooth: HCI BCSP protocol initialized
- Bluetooth: HCILL protocol initialized
- usbcore: registered new interface driver usbhid
- usbhid: USB HID core driver
- usbcore: registered new interface driver snd-usb-audio
- No device for DAI omap-mcbsp-dai-0
- No device for DAI omap-mcbsp-dai-1
- No device for DAI omap-mcbsp-dai-2
- No device for DAI omap-mcbsp-dai-3
- No device for DAI omap-mcbsp-dai-4
- OMAP3 Beagle/Devkit8000 SoC init
- asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
- ALSA device list:
- #0: omap3beagle (twl4030)
- oprofile: hardware counters not available
- oprofile: using timer interrupt.
- TCP cubic registered
- NET: Registered protocol family 17
- NET: Registered protocol family 15
- Bluetooth: L2CAP ver 2.15
- Bluetooth: L2CAP socket layer initialized
- Bluetooth: SCO (Voice Link) ver 0.6
- Bluetooth: SCO socket layer initialized
- Bluetooth: RFCOMM TTY layer initialized
- Bluetooth: RFCOMM socket layer initialized
- Bluetooth: RFCOMM ver 1.11
- Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- Bluetooth: BNEP filters: protocol multicast
- Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- Registering the dns_resolver key type
- ThumbEE CPU extension supported.
- Power Management for TI OMAP3.
- VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
- fbcvt: 1024x768@60: CVT Name - .786M3-R
- Console: switching to colour frame buffer device 128x48
- regulator_init_complete: incomplete constraints, leaving VDAC on
- twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
- Waiting for root device /dev/mmcblk0p2...
- usb 2-2: new high speed USB device using ehci-omap and address 2
- mmc0: new high speed SDHC card at address e624
- mmcblk0: mmc0:e624 SU04G 3.69 GiB
- mmcblk0: p1 p2
- usb 2-2: New USB device found, idVendor=0424, idProduct=9514
- usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
- hub 2-2:1.0: USB hub found
- hub 2-2:1.0: 5 ports detected
- EXT3-fs: barriers not enabled
- usb 2-2.1: new high speed USB device using ehci-omap and address 3
- usb 2-2.1: New USB device found, idVendor=0424, idProduct=ec00
- usb 2-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
- kjournald starting. Commit interval 5 seconds
- EXT3-fs (mmcblk0p2): warning: maximal mount count reached, running e2fsck is
- recommended
- EXT3-fs (mmcblk0p2): using internal journal
- EXT3-fs (mmcblk0p2): recovery complete
- EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
- VFS: Mounted root (ext3 filesystem) on device 179:2.
- devtmpfs: mounted
- Freeing init memory: 164K
- INIT: version 2.86 booting
- Please wait: booting...
- Starting udev
- udev[86]: starting version 162
- Remounting root file system...
- smsc95xx v1.0.4
- smsc95xx 2-2.1:1.0: usb0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0
- Ethernet, c2:44:0d:99:19:f4
- usbcore: registered new interface driver smsc95xx
- Caching udev devnodes
- Populating dev cache
- NET: Registered protocol family 10
- ALSA: Restoring mixer settings...
- Cleaning: /etc/network/run/ifstate.
- Configuring network interfaces... done.
- Starting portmap daemon: portmap.
- net.ipv4.conf.default.rp_filter = 1
- net.ipv4.conf.all.rp_filter = 1
- Sun Mar 6 21:42:00 GMT 2011
- INIT: Entering runlevel: 5
- Starting system message bus: dbus.
- Starting Hardware abstraction layer hald
- Starting OpenBSD Secure Shell server: sshd
- done.
- sshd (454): /proc/454/oom_adj is deprecated, please use /proc/454/oom_score_adj instead.
- Starting advanced power management daemon: No APM support in kernel
- (failed.)
- Starting Vixie-cron.
- /etc/rc5.d/S20nfsserver: line 22: test: : integer expression expected
- creating NFS state directory: done
- starting 8 nfsd kernel threads: done
- starting mountd: done
- starting statd: done
- Starting ntpd: done
- Starting Samba: smbd nmbd.
- Starting syslog-ng:.
- Starting internet superserver: xinetd.
- * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ]
- Starting Bluetooth subsystem:
- Initialization timed out.
- Starting Network connection manager daemon: NetworkManager.
- Starting PVR
- cups: started scheduler.
- Starting GNOME Display Manager gdm
- .-------.
- | | .-.
- | | |-----.-----.-----.| | .----..-----.-----.
- | | | __ | ---'| '--.| .-'| | |
- | | | | | |--- || --'| | | ' | | | |
- '---'---'--'--'--. |-----''----''--' '-----'-'-'-'
- -' |
- '---'
- The Angstrom Distribution omap3-multi ttyS2
- Angstrom 2010.7-test-20110307 omap3-multi ttyS2
- omap3-multi login:
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement