API tools faq
paste
Advertisement
Guest User

Vim android 6 bootlog

a guest
May 15th, 2017
740
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 62.41 KB | None | 0 0
raw download clone embed print report
  1. �GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
  2. TE: 139432
  3.  
  4. BL2 Built : 13:48:56, Sep 23 2016.
  5. gxl g7459bd4 - jianxin.pan@droid06
  6.  
  7. set vcck to 1120 mv
  8. set vddee to 1000 mv
  9. Board ID = 6
  10. CPU clk: 1200MHz
  11. DQS-corr enabled
  12. DDR scramble enabled
  13. DDR3 chl: Rank0+1 @ 768MHz - PASS
  14. Rank0: 1024MB(auto)-2T-11
  15. Rank1: 1024MB(auto)-2T-11
  16. DataBus test pass!
  17. AddrBus test pass!
  18. -s
  19. Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
  20. New fip structure!
  21. Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
  22. Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00015400
  23. Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a6400
  24. NOTICE: BL3-1: v1.0(debug):fb68908
  25. NOTICE: BL3-1: Built : 18:30:11, Nov 1 2016
  26. aml log : bl31 normal boot !
  27. [Image: gxl_v1.1.3154-065f772 2016-09-29 14:08:54 yan.wang@droid05]
  28. OPS=0x82
  29. 4a 46 7c e1 87 10 28 b5 ad 64 33 8 [0.381901 Inits done]
  30. secure task start!
  31. high task start!
  32. low task start!
  33. INFO: BL3-1: Initializing runtime services
  34. WARNING: No OPTEE provided by BL2 boot loader
  35. ERROR: Error initializing runtime service opteed_fast
  36. INFO: BL3-1: Preparing for EL3 exit to normal world
  37. INFO: BL3-1: Next image address = 0x1000000
  38. INFO: BL3-1: Next image spsr = 0x3c9
  39.  
  40.  
  41. U-Boot 2015.01-g207958a (Jan 21 2017 - 11:58:03)
  42.  
  43. DRAM: 2 GiB
  44. Relocation Offset is: 76ecc000
  45. register usb cfg[0][1] = 0000000077f5f1a8
  46. vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
  47. vpu: clk_level = 7
  48. vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
  49. vpp: vpp_init
  50. boot_device_flag : 1
  51. Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
  52. init bus_cycle=6, bus_timing=7, system=5.0ns
  53. reset failed
  54. get_chip_type and ret:fffffffe
  55. get_chip_type and ret:fffffffe
  56. chip detect failed and ret:fffffffe
  57. nandphy_init failed and ret=0xfffffff1
  58. MMC: aml_priv->desc_buf = 0x0000000073ecc6b0
  59. aml_priv->desc_buf = 0x0000000073ece9d0
  60. SDIO Port B: 0, SDIO Port C: 1
  61. emmc/sd response timeout, cmd8, status=0x1ff2800
  62. emmc/sd response timeout, cmd55, status=0x1ff2800
  63. [mmc_startup] mmc refix success
  64. [mmc_init] mmc init success
  65. mmc read lba=0x14000, blocks=0x400
  66. start dts,buffer=0000000073ed1270,dt_addr=0000000073ed1270
  67. parts: 11
  68. 00: logo 0000000002000000 1
  69. 01: recovery 0000000002000000 1
  70. 02: rsv 0000000000800000 1
  71. 03: tee 0000000000800000 1
  72. 04: crypt 0000000002000000 1
  73. 05: misc 0000000002000000 1
  74. 06: instaboot 0000000020000000 1
  75. 07: boot 0000000002000000 1
  76. 08: system 0000000040000000 1
  77. 09: cache 0000000020000000 2
  78. 10: data ffffffffffffffff 4
  79. get_dtb_struct: Get emmc dtb OK!
  80. overide_emmc_partition_table: overide cache
  81. [mmc_get_partition_table] skip partition cache.
  82. Partition table get from SPL is :
  83. name offset size flag
  84. ===================================================================================
  85. 0: bootloader 0 400000 0
  86. 1: reserved 2400000 4000000 0
  87. 2: cache 6c00000 20000000 2
  88. 3: env 27400000 800000 0
  89. 4: logo 28400000 2000000 1
  90. 5: recovery 2ac00000 2000000 1
  91. 6: rsv 2d400000 800000 1
  92. 7: tee 2e400000 800000 1
  93. 8: crypt 2f400000 2000000 1
  94. 9: misc 31c00000 2000000 1
  95. 10: instaboot 34400000 20000000 1
  96. 11: boot 54c00000 2000000 1
  97. 12: system 57400000 40000000 1
  98. 13: data 97c00000 30c200000 4
  99. mmc read lba=0x12000, blocks=0x2
  100. mmc read lba=0x12002, blocks=0x2
  101. mmc_read_partition_tbl: mmc read partition OK!
  102. eMMC/TSD partition table have been checked OK!
  103. mmc env offset: 0x27400000
  104. In: serial
  105. Out: serial
  106. Err: serial
  107. reboot_mode=cold_boot
  108. hpd_state=0
  109. set hdmitx VIC = 16
  110. config HPLL = 2970
  111. HPLL: 0xc000027b
  112. config HPLL done
  113. j = 4 vid_clk_div = 1
  114. hdmitx phy setting done
  115. hdmitx: set enc for VIC: 16
  116. rx version is 1.4 or below div=10
  117. hdmtix: set audio
  118. [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
  119. read emmc dtb
  120. Net: dwmac.c9410000
  121. wipe_data=successful
  122. wipe_cache=successful
  123. upgrade_step=2
  124. [OSD]load fb addr from dts
  125. [OSD]failed to get fb addr for logo
  126. [OSD]use default fb_addr parameters
  127. [OSD]fb_addr for logo: 0x3d800000
  128. [OSD]load fb addr from dts
  129. [OSD]failed to get fb addr for logo
  130. [OSD]use default fb_addr parameters
  131. [OSD]fb_addr for logo: 0x3d800000
  132. [CANVAS]canvas init
  133. [CANVAS]addr=0x3d800000 width=3840, height=2160
  134. amlkey_init() enter!
  135. [EFUSE_MSG]keynum is 4
  136. [BL31]: tee size: 0
  137. [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
  138. [KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
  139. [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
  140. get_cpu_id flag_12bit=1
  141. saradc - saradc sub-system
  142.  
  143. Usage:
  144. saradc saradc open <channel> - open a SARADC channel
  145. saradc close - close the SARADC
  146. saradc getval - get the value in current channel
  147. saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
  148.  
  149. gpio: pin GPIOAO_2 (gpio 102) value is 1
  150. get_cpu_id flag_12bit=1
  151. Product checking: pass!
  152. Hit Enter or space or Ctrl+C key to stop autoboot -- : 1  0
  153. ee_gate_off ...
  154. ## Booting Android Image at 0x01080000 ...
  155. reloc_addr =73f51440
  156. copy done
  157. load dtb from 0x1000000 ......
  158. Uncompressing Kernel Image ... OK
  159. kernel loaded at 0x01080000, end = 0x0210aa00
  160. Loading Ramdisk to 73dd8000, end 73eb969d ... OK
  161. Loading Device Tree to 000000001fff3000, end 000000001ffff4dc ... OK
  162. signature:
  163. fdt_instaboot: no instaboot image
  164.  
  165. Starting kernel ...
  166.  
  167. uboot time: 1889779 us
  168. [ 0.000000@0] Initializing cgroup subsys cpu
  169. [ 0.000000@0] Initializing cgroup subsys cpuacct
  170. [ 0.000000@0] Linux version 3.14.29-g76fd19a (terry@Server) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #32 SMP PREEMPT Sat Jan 21 11:05:09 CST 2017
  171. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  172. [ 0.000000@0] no prop version_code
  173. [ 0.000000@0] bootconsole [earlycon0] enabled
  174. [ 0.000000@0] fdt Reserved memory table:
  175. [ 0.000000@0] linux,meson-fb: 0x000000007e000000 - 0x0000000080000000 (32 MiB)
  176. [ 0.000000@0] linux,di: 0x000000007c200000 - 0x000000007e000000 (30 MiB)
  177. [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007c200000, size 30 MiB
  178. [ 0.000000@0] linux,ion-dev: 0x0000000079200000 - 0x000000007c200000 (48 MiB)
  179. [ 0.000000@0] linux,ppmgr: 0x0000000079200000 - 0x0000000079200000 (0 MiB)
  180. [ 0.000000@0] linux,codec_mm_cma: 0x0000000067c00000 - 0x0000000073c00000 (192 MiB)
  181. [ 0.000000@0] linux,picdec: 0x0000000079200000 - 0x0000000079200000 (0 MiB)
  182. [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
  183. [ 0.000000@0] linux,codec_mm_reserved: 0x0000000075100000 - 0x0000000079200000 (65 MiB)
  184. [ 0.000000@0] fdt Reserved memory total: 370 MiB
  185. [ 0.000000@0] cma: Reserved 8 MiB at 74800000
  186. [ 0.000000@0] psci: probing function IDs from device-tree
  187. [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc0750a1000 s19968 r8192 d20992 u49152
  188. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 506004
  189. [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=disabled logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=4 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv= androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic
  190. [ 0.000000@0] logo: osd1
  191. [ 0.000000@0] logo: loaded
  192. [ 0.000000@0] logo: 0x3d800000
  193. [ 0.000000@0] logo: 1080p60hz
  194. [ 0.000000@0] vout_serve: 1080p60hz
  195. [ 0.000000@0] vout_serve: enable: 1
  196. [ 0.000000@0] logo: get hdmimode: 1080p60hz
  197. [ 0.000000@0] logo: get cvbsmode: 576cvbs
  198. [ 0.000000@0] tv_vout: cvbs performance line =
  199. [ 0.000000@0] jtag: jtag select 2
  200. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  201. [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  202. [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  203. [ 0.000000@0] Memory: 1642880K/2060288K available (10620K kernel code, 1158K rwdata, 3888K rodata, 1263K init, 5868K bss, 417408K reserved)
  204. [ 0.000000@0] Virtual kernel memory layout:
  205. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
  206. [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8042380000 ( 35 MB)
  207. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  208. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07e000000 ( 2016 MB)
  209. [ 0.000000@0] .init : 0xffffffc001ead000 - 0xffffffc001fe8e00 ( 1264 kB)
  210. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001eac354 ( 14513 kB)
  211. [ 0.000000@0] .data : 0xffffffc001fe9000 - 0xffffffc00210aa00 ( 1159 kB)
  212. [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01eabfff]
  213. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
  214. [ 0.000000@0] arch_multi_cluster:0
  215. [ 0.000000@0] Preemptible hierarchical RCU implementation.
  216. [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
  217. [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
  218. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  219. [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
  220. [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
  221. [ 0.008246@0] meson_bc_timer: mclk->mux_reg =ffffff800000c990,mclk->reg =ffffff800000e994
  222. [ 0.016800@0] Console: colour dummy device 80x25
  223. [ 0.021095@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
  224. [ 0.031673@0] pid_max: default: 32768 minimum: 301
  225. [ 0.036565@0] Security Framework initialized
  226. [ 0.040786@0] SELinux: Initializing.
  227. [ 0.044541@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  228. [ 0.051369@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  229. [ 0.061239@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
  230. [ 0.065747@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
  231. [ 0.072718@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
  232. [ 0.079721@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
  233. [ 0.090129@0] Initializing cgroup subsys debug
  234. [ 0.091176@0] Initializing cgroup subsys freezer
  235. [ 0.095843@0] ftrace: allocating 36521 entries in 143 pages
  236. [ 0.141383@0] /cpus/cpu@0: Missing clock-frequency property
  237. [ 0.141424@0] /cpus/cpu@1: Missing clock-frequency property
  238. [ 0.147010@0] /cpus/cpu@2: Missing clock-frequency property
  239. [ 0.152635@0] /cpus/cpu@3: Missing clock-frequency property
  240. [ 0.158210@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
  241. [ 0.208484@0] Meson chip version = RevA (21:A - 82:0)
  242. [ 0.226897@1] CPU1: Booted secondary processor
  243. [ 0.246884@2] CPU2: Booted secondary processor
  244. [ 0.266890@3] CPU3: Booted secondary processor
  245. [ 0.266969@0] Brought up 4 CPUs
  246. [ 0.277935@0] SMP: Total of 4 processors activated.
  247. [ 0.290629@0] sched: registering cpufreq notifiers for scale-invariant loads
  248. [ 0.292154@0] instabooting: 0
  249. [ 0.304208@0] pinctrl core: initialized pinctrl subsystem
  250. [ 0.304900@0] regulator-dummy: no parameters
  251. [ 0.309145@0] NET: Registered protocol family 16
  252. [ 0.314653@0] ramoops: using module parameters
  253. [ 0.318034@0] console [pstore-1] enabled
  254. [ 0.321404@0] pstore: Registered ramoops as persistent store backend
  255. [ 0.327765@0] ramoops: attached 0x100000@0x7300000, ecc: 0/0
  256. [ 0.334376@0] cpuidle: using governor menu
  257. [ 0.337845@0] aml_vdac_init: module init
  258. [ 0.341668@0] register canvas platform driver
  259. [ 0.345992@0] register rdma platform driver
  260. [ 0.351537@0] vdso: 2 pages (1 code, 1 data) at base ffffffc001ff4000
  261. [ 0.356614@0] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  262. [ 0.363827@0] DMA: preallocated 256 KiB pool for atomic allocations
  263. [ 0.370828@0] software IO TLB [mem 0x64800000-0x64c00000] (4MB) mapped at [ffffffc064800000-ffffffc064bfffff]
  264. [ 0.379828@0] Serial: AMBA PL011 UART driver
  265. [ 0.384704@0] aml_i2c version: 20140813
  266. [ 0.388215@0] i2c-core: driver [pmu4] using legacy resume method
  267. [ 0.394198@0] codec_mm:codec_mm_module_init
  268. [ 0.398461@0] aml_watch_point_probe, in
  269. [ 0.402423@0] gxbb_mpll_clk: register mpll_clk_out0 success done
  270. [ 0.408115@0] gxbb_mpll_clk: register mpll_clk_out1 success done
  271. [ 0.414130@0] gxbb_mpll_clk: register mpll_clk_out2 success done
  272. [ 0.420373@0] clk_sys: register PLL sys_pll success done
  273. [ 0.425511@0] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
  274. [ 0.430850@0] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
  275. [ 0.436003@0] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
  276. [ 0.441522@0] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
  277. [ 0.447465@0] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
  278. [ 0.453421@0] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
  279. [ 0.459277@0] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
  280. [ 0.465146@0] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
  281. [ 0.471002@0] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
  282. [ 0.476895@0] gxl_clk: clock initialization complete
  283. [ 0.482057@0] clkmsr: Gxl msr_clk_reg0=ffffff800003a75c,msr_clk_reg2=ffffff800003c764
  284. [ 0.492250@0] aml_iomap: amlogic iomap probe done
  285. [ 0.495123@0] pinmux-gxl c1109880.pinmux: Init pinux probe!
  286. [ 0.501059@0] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
  287. [ 0.507750@0] aml-i2c c11087c0.i2c: add adapter aml_i2c_adap2(ffffffc06555b8e0)
  288. [ 0.514415@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
  289. [ 0.522115@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
  290. [ 0.530367@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
  291. [ 0.538211@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
  292. domain-0 init dvfs: 4
  293. [ 0.556206@0] codec_mm has 2 memory regions
  294. [ 0.556266@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
  295. [ 0.562910@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
  296. [ 0.571504@0] codec_mm has 2 memory regions
  297. [ 0.575593@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
  298. [ 0.583619@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
  299. [ 0.594047@0] vpu: driver version: v02
  300. [ 0.595894@0] vpu: load vpu_clk: 666667000Hz(7)
  301. [ 0.600507@0] vpu: vpu_probe OK
  302. [ 0.605253@0] tv_vout: tvout_probe
  303. [ 0.606986@0] tv_vout: major number 254 for disp
  304. [ 0.611615@0] vout_notify: vout_register_server
  305. [ 0.616184@0] tv_vout: register tv module server ok
  306. [ 0.621209@0] tv_vout: tvout_probe OK
  307. [ 0.625385@0] canvas_probe reg=00000000c8838000,size=400
  308. [ 0.630116@0] canvas maped reg_base =ffffff800009a000
  309. [ 0.639466@0] rdma_probe
  310. [ 0.964413@0] bio: create slab <bio-0> at 0
  311. [ 0.965508@0] SCSI subsystem initialized
  312. [ 0.967544@0] usbcore: registered new interface driver usbfs
  313. [ 0.972801@0] usbcore: registered new interface driver hub
  314. [ 0.978308@0] usbcore: registered new device driver usb
  315. [ 0.984392@0] i2c-gpio i2c_gpio.37: using pins 172 (SDA) and 173 (SCL)
  316. [ 0.990192@0] Linux video capture interface: v2.00
  317. [ 0.995049@0] pps_core: LinuxPPS API ver. 1 registered
  318. [ 0.999957@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  319. [ 1.009482@0] PTP clock support registered
  320. [ 1.014110@0] hdmitx: system: amhdmitx_init
  321. [ 1.017634@0] hdmitx: system: Ver: 2014May6
  322. [ 1.022023@0] hdmitx: system: amhdmitx_probe
  323. [ 1.026426@0] hdmitx: system: not find match init-data
  324. [ 1.031282@0] hdmitx: system: not find match pwr-ctl
  325. [ 1.036288@0] hdmitx hpd irq = 89
  326. [ 1.040108@0] hdmitx20: Mapped PHY: 0xc0800000
  327. [ 1.044064@0] hdmitx20: Mapped PHY: 0xc1104400
  328. [ 1.048556@0] hdmitx20: Mapped PHY: 0xc8100000
  329. [ 1.052984@0] hdmitx20: Mapped PHY: 0xc8834000
  330. [ 1.057446@0] hdmitx20: Mapped PHY: 0xc883a000
  331. [ 1.061916@0] hdmitx20: Mapped PHY: 0xc883c000
  332. [ 1.066374@0] hdmitx20: Mapped PHY: 0xd0100000
  333. [ 1.070833@0] hdmitx20: Mapped PHY: 0xda83a000
  334. [ 1.075308@0] hdmitx: alread display in uboot 0x10
  335. [ 1.080125@0] avmute set to 1
  336. [ 1.083479@0] vout_serve: vout_init_module
  337. [ 1.087344@0] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
  338. [ 1.093409@0] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
  339. [ 1.100334@0] tv_vout: already display in uboot
  340. [ 1.104869@0] vout_serve: vinfo mode is: 1080p60hz
  341. [ 1.109682@0] vout_serve: init mode 1080p60hz
  342. [ 1.114175@0] vout_serve: create vout attribute OK
  343. [ 1.118869@0] vout_serve: meson_vout_probe OK
  344. [ 1.123441@0] logo: logo_init
  345. [ 1.126498@0] osd_rdma: osd_rdma_init: rdma_table p=0x74841000,op=0x74841000 , v=0xffffff800009e000
  346. [ 1.135324@0] osd_rdma: osd rdma request irq as second interrput function!
  347. [ 1.142261@0] logo: mode chang
  348. [ 1.147277@0] vout_serve: vmode set to 576cvbs
  349. [ 1.149780@0] tv_vout: tv_set_current_vmode[759]fps_target_mode=7
  350. [ 1.155892@0] tv_vout: mode is 7,sync_duration_den=1,sync_duration_num=50
  351. [ 1.162711@0] tv_vout: TV mode 576cvbs selected.
  352. [ 1.167370@0]
  353. [ 1.167370@0] vdac_enable: on:0,module_sel:8
  354. [ 1.173300@0] enc_clk_config: mode is: 7
  355. [ 1.177231@0] enc_clk_config: config HPLL
  356. [ 1.181347@0] enc_clk_config: config HPLL done
  357. [ 1.185749@0] tv_vout: cvbs performance type = 6, table = 0
  358. [ 2.201670@0] tv_vout: vdac open.0 = 0xb0001, 0x0
  359. [ 2.201695@0]
  360. [ 2.201695@0] vdac_enable: on:1,module_sel:8
  361. [ 2.206781@0] tv_vout: new mode =576cvbs set ok
  362. [ 2.211306@0] vout_serve: vinfo mode is: 576cvbs
  363. [ 2.215952@0] vout_serve: new mode 576cvbs set ok
  364. [ 2.220679@0] hdmitx: edid: not find mapped vic
  365. [ 2.225220@0] hdmitx: edid: not find mapped vic
  366. [ 2.229802@0] hdmitx: video: get current mode: 576cvbs
  367. [ 2.234932@0] hdmitx: update rx hdr info 0
  368. [ 2.239044@0] hdmitx: video: 576cvbs not valid hdmi mode
  369. [ 2.244408@0] logo: set vmode: 576cvbs
  370. [ 2.248173@0] hdmitx: edid: not find mapped vic
  371. [ 2.252694@0] hdmitx: edid: not find mapped vic
  372. [ 2.257255@0] hdmitx: video: get current mode: 576cvbs
  373. [ 2.262406@0] hdmitx: update rx hdr info 0
  374. [ 2.266541@0] hdmitx: video: 576cvbs not valid hdmi mode
  375. [ 2.271872@0] logo: outputmode changed to 576cvbs, reset osd1 scaler
  376. [ 2.325816@0] logo: finish
  377. [ 2.326317@0] Advanced Linux Sound Architecture Driver Initialized.
  378. [ 2.329887@0] Bluetooth: Core ver 2.18
  379. [ 2.333150@0] NET: Registered protocol family 31
  380. [ 2.337641@0] Bluetooth: HCI device and connection manager initialized
  381. [ 2.344223@0] Bluetooth: HCI socket layer initialized
  382. [ 2.349320@0] Bluetooth: L2CAP socket layer initialized
  383. [ 2.354560@0] Bluetooth: SCO socket layer initialized
  384. [ 2.360049@0] cfg80211: Calling CRDA to update world regulatory domain
  385. [ 2.366348@0] NetLabel: Initializing
  386. [ 2.369753@0] NetLabel: domain hash size = 128
  387. [ 2.374301@0] NetLabel: protocols = UNLABELED CIPSOv4
  388. [ 2.379543@0] NetLabel: unlabeled traffic allowed by default
  389. [ 2.387054@0] Switched to clocksource arch_sys_counter
  390. [ 2.437244@0] [amlatvdemod..]aml_atvdemod_init.
  391. [ 2.437374@0] NET: Registered protocol family 2
  392. [ 2.441253@0] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  393. [ 2.448385@0] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  394. [ 2.455267@0] TCP: Hash tables configured (established 16384 bind 16384)
  395. [ 2.461834@0] TCP: reno registered
  396. [ 2.465178@0] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  397. [ 2.471466@0] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  398. [ 2.478283@0] NET: Registered protocol family 1
  399. [ 2.482865@0] RPC: Registered named UNIX socket transport module.
  400. [ 2.488758@0] RPC: Registered udp transport module.
  401. [ 2.493608@0] RPC: Registered tcp transport module.
  402. [ 2.498520@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
  403. [ 2.505356@0] aml_wifi wifi.32: [wifi_dev_probe] no power_on_pin2
  404. [ 2.511322@0] aml_wifi wifi.32: [wifi_dev_probe] set pwm as 32k output
  405. [ 2.517897@0] aml_wifi wifi.32: [wifi_dev_probe] dhd_static_buf setup
  406. [ 2.524379@0] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
  407. [ 2.531989@0] aml_wifi wifi.32: [wifi_dev_probe] interrupt_pin=241
  408. [ 2.538155@0] aml_wifi wifi.32: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
  409. [ 2.545585@0] aml_wifi wifi.32: [wifi_dev_probe] power_on_pin=240
  410. [ 2.551740@0] aml_wifi wifi.32: [wifi_dev_probe] clock_32k_pin=0
  411. [ 2.558063@0] aml_wifi wifi.32: [wifi_setup_dt] wifi_setup_dt
  412. [ 2.563552@0] aml_wifi wifi.32: [wifi_setup_dt] interrupt_pin(241)
  413. [ 2.569790@0] aml_wifi wifi.32: [wifi_setup_dt] power_on_pin(240)
  414. [ 2.576226@0] Unpacking initramfs...
  415. [ 2.611130@0] Freeing initrd memory: 900K (ffffffc073dd8000 - ffffffc073eb9000)
  416. [ 2.617398@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
  417. [ 2.619338@0] audit: initializing netlink subsys (disabled)
  418. [ 2.624921@0] audit: type=2000 audit(2.410:1): initialized
  419. [ 2.631347@0] HugeTLB registered 2 MB page size, pre-allocated 0 pages
  420. [ 2.644550@0] VFS: Disk quotas dquot_6.5.2
  421. [ 2.644837@0] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  422. [ 2.655163@0] NFS: Registering the id_resolver key type
  423. [ 2.655225@0] Key type id_resolver registered
  424. [ 2.659378@0] Key type id_legacy registered
  425. [ 2.663582@0] NTFS driver 2.1.30 [Flags: R/O].
  426. [ 2.668525@0] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
  427. [ 2.676070@0] fuse init (API version 7.22)
  428. [ 2.680109@0] msgmni has been set to 3610
  429. [ 2.685044@0] NET: Registered protocol family 38
  430. [ 2.688543@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
  431. [ 2.695676@0] io scheduler noop registered
  432. [ 2.699829@0] io scheduler deadline registered
  433. [ 2.704465@0] io scheduler cfq registered (default)
  434. [ 2.760989@0] meson-rng c8834000.rng: hwrng registered
  435. [ 2.764600@0] loop: module loaded
  436. [ 2.765223@0] zram: Created 1 device(s) ...
  437. [ 2.770197@0] mtdoops: mtd device (mtddev=name/number) must be supplied
  438. [ 2.775622@0] tun: Universal TUN/TAP device driver, 1.6
  439. [ 2.780012@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  440. [ 2.794040@0] libphy: stmmac: probed
  441. [ 2.794074@0] eth0: PHY ID 01814400 at 8 IRQ POLL (stmmac-0:08) active
  442. [ 2.799100@0] PPP generic driver version 2.4.2
  443. [ 2.803284@0] PPP BSD Compression module registered
  444. [ 2.808024@0] PPP Deflate Compression module registered
  445. [ 2.813237@0] PPP MPPE Compression module registered
  446. [ 2.818216@0] NET: Registered protocol family 24
  447. [ 2.823036@0] usbcore: registered new interface driver asix
  448. [ 2.828652@0] usbcore: registered new interface driver ax88179_178a
  449. [ 2.834863@0] usbcore: registered new interface driver cdc_ether
  450. [ 2.841012@0] usbcore: registered new interface driver net1080
  451. [ 2.846820@0] usbcore: registered new interface driver cdc_subset
  452. [ 2.852907@0] usbcore: registered new interface driver zaurus
  453. [ 2.858701@0] usbcore: registered new interface driver cdc_ncm
  454. [ 2.864723@0] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  455. [ 2.871194@0] ehci-h20ahb: H20AHB-EHCI Host Controller driver
  456. [ 2.877227@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  457. [ 2.883740@0] usbcore: registered new interface driver cdc_acm
  458. [ 2.889223@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  459. [ 2.897555@0] usbcore: registered new interface driver usb-storage
  460. [ 2.903877@0] usbcore: registered new interface driver usbserial
  461. [ 2.910485@0] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80000da000
  462. [ 2.920624@0] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
  463. [ 2.927218@0] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80000ee080
  464. [ 2.938566@0] mousedev: PS/2 mouse device common for all mice
  465. [ 2.944105@0] usbcore: registered new interface driver xpad
  466. [ 2.953078@0] kvim_hym8563 2-0051: rtc core: registered kvim_hym8563 as rtc0
  467. [ 2.956389@0] i2c /dev entries driver
  468. [ 2.960469@0] usbcore: registered new interface driver uvcvideo
  469. [ 2.965950@0] USB Video Class driver (1.1.1)
  470. [ 2.971123@0] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
  471. [ 2.978983@0] Bluetooth: HCI UART driver ver 2.2
  472. [ 2.983496@0] Bluetooth: HCI H4 protocol initialized
  473. [ 2.988956@0] CPUidle arm64: cpuidle init start!!
  474. [ 2.993848@0] hidraw: raw HID events driver (C) Jiri Kosina
  475. [ 2.999149@0] @@@@@@@@@@_____2______in dia_init()
  476. [ 3.003533@0] ATVR driver - init called!
  477. [ 3.007761@0] usbcore: registered new interface driver usbhid
  478. [ 3.013244@0] usbhid: USB HID core driver
  479. [ 3.017717@0] ashmem: initialized
  480. [ 3.020777@0] logger: created 256K log 'log_main'
  481. [ 3.025477@0] logger: created 256K log 'log_events'
  482. [ 3.030456@0] logger: created 256K log 'log_radio'
  483. [ 3.035191@0] logger: created 256K log 'log_system'
  484. [ 3.041250@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80000fc4c0
  485. [ 3.047188@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
  486. [ 3.062160@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
  487. [ 3.064788@0] console [ttyS0] enabled
  488. [ 3.064788@0] console [ttyS0] enabled
  489. [ 3.072060@0] bootconsole [earlycon0] disabled
  490. [ 3.072060@0] bootconsole [earlycon0] disabled
  491. [ 3.081232@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80000fe4c0
  492. [ 3.087881@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
  493. [ 3.097877@0] hdmitx: system: hdmitx_hdcp_init
  494. [ 3.101696@0] ESM HLD: Initializing...
  495. [ 3.105235@0] ESM HLD: Registering device range 'esm'...
  496. [ 3.110556@0] ESM HLD: Device range 'esm' has been registered.
  497. [ 3.116274@0] ESM HLD: Creating class /sys/class/elliptic...
  498. [ 3.122000@0] ESM HLD: The class /sys/class/elliptic has been created.
  499. [ 3.128389@0] ESM HLD: Creating device 'esm'...
  500. [ 3.132982@0] ESM HLD: Device 'esm' has been created.
  501. [ 3.137845@0] ESM HLD: Done initializing the HLD driver.
  502. INFO: HDCP22 key read fail!
  503. INFO: p1d 0
  504. INFO: pd1 0
  505. [ 3.159101@0] aml_vrtc rtc.31: rtc core: registered aml_vrtc as rtc1
  506. [ 3.160523@0] secmon has 1 memory regions
  507. [ 3.163802@0] secmon: share in base: 0xffffff800011a000, share out base: 0xffffff800011c000
  508. [ 3.172111@0] secmon secmon.4: assigned reserved memory node linux,secmon ok
  509. [ 3.179046@0] secmon: probe done
  510. [ 3.182583@0] storage: storage in base: 0xffffff8001800000
  511. [ 3.187710@0] storage: storage out base: 0xffffff8001880000
  512. [ 3.193182@0] storage: storage block base: 0xffffff8001900000
  513. [ 3.198881@0] storage: probe done!
  514. [ 3.202843@0] aml_sd_emmc_probe: line 3558
  515. [ 3.206335@0] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
  516. [ 3.216103@0] aml_sd_emmc_reg_init 1146
  517. [ 3.219566@0] get property: ocr_avail, value:0x00200080
  518. [ 3.225997@0] get property: f_min, value:400000
  519. [ 3.232089@0] get property: f_max, value:100000000
  520. [ 3.238472@0] get property: max_req_size, value:0x00020000
  521. [ 3.244933@0] get property: irq_in, value:3
  522. [ 3.250655@0] get property: irq_out, value:5
  523. [ 3.256330@0] get property: gpio_cd, str:
  524. [ 3.261760@0] get property: pinname, str:sd
  525. [ 3.267389@0] get property: jtag_pin, str:
  526. [ 3.272793@0] get property: card_type, value:5
  527. [ 3.278497@0] get property: gpio_dat3, str:
  528. [ 3.283933@0] sd:pdata->caps = 7
  529. [ 3.287139@0] sd:pdata->caps2 = 0
  530. [ 3.328264@1] [aml_is_card_insert] card OUT
  531. [ 3.328351@0] [aml_is_card_insert] card OUT
  532. [ 3.330974@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  533. [ 3.336763@0] aml_sd_emmc_probe: line 3558
  534. [ 3.341098@0] aml_sd_emmc_reg_init 1146
  535. [ 3.344636@0] get property: ocr_avail, value:0x00200080
  536. [ 3.351105@0] get property: f_min, value:300000
  537. [ 3.357186@0] get property: f_max, value:100000000
  538. [ 3.363562@0] get property: max_req_size, value:0x00020000
  539. [ 3.370063@0] get property: pinname, str:emmc
  540. [ 3.375811@0] get property: card_type, value:1
  541. [ 3.381519@0] get property: gpio_dat3, str:
  542. [ 3.386959@0] get property: hw_reset, str:
  543. [ 3.392411@0] emmc:pdata->caps = c0000d47
  544. [ 3.396340@0] emmc:pdata->caps2 = 18060
  545. [ 3.400147@0] storage 1, boot 1
  546. [ 3.403235@0] get_storage_dev return 1
  547. [ 3.447067@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  548. [ 3.452553@0] aml_sd_emmc_probe: line 3558
  549. [ 3.452950@0] aml_sd_emmc_reg_init 1146
  550. [ 3.455191@0] get property: ocr_avail, value:0x00200080
  551. [ 3.461664@0] get property: f_min, value:400000
  552. [ 3.467814@0] get property: f_max, value:200000000
  553. [ 3.474083@0] get property: max_req_size, value:0x00020000
  554. [ 3.480561@0] get property: pinname, str:sdio
  555. [ 3.486354@0] get property: card_type, value:3
  556. [ 3.492152@0] sdio:pdata->caps = 7810f
  557. [ 3.495730@0] sdio:pdata->caps2 = 0
  558. [ 3.537071@0] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  559. [ 3.537614@0] ion_dev has 1 memory regions
  560. [ 3.545244@0] fb: osd_init_module
  561. [ 3.545391@0] fb: viu vsync irq: 35
  562. [ 3.548176@0] meson-fb has 1 memory regions
  563. [ 3.552387@0] meson-fb meson-fb.16: assigned reserved memory node linux,meson-fb ok
  564. [ 3.559878@0] fb: osd_probe vinfo:ffffffc00208af08
  565. [ 3.564588@0] fb: init fbdev bpp is:32
  566. [ 3.579249@1] emmc: BKOPS_EN bit is not set
  567. [ 3.585619@1] emmc: trying cali 0-th time(s)
  568. [ 3.585772@0] fb: osd probe OK
  569. [ 3.587556@0] ge2d: ge2d_init_module
  570. [ 3.590818@0] ge2d: ge2d_dev major:242
  571. [ 3.594922@0] ge2d: ge2d clock is 400 MHZ
  572. [ 3.598505@0] ge2d: ge2d: pdev=ffffffc065620400, irq=182, rstc=0xffffffc06559fa00, clk=ffffffc065503b00
  573. [ 3.607899@0] ge2d: mapped phy: 0xd0160000
  574. [ 3.611856@0] ge2d: ge2d start monitor
  575. [ 3.615840@0] ge2d: ge2d workqueue monitor start
  576. [ 3.620174@2] sysled: module init
  577. [ 3.623556@2] sysled: led_gpio = 154
  578. [ 3.624892@1] emmc: delay[0]= 800 padding= 1, bidx=0
  579. [ 3.624895@1] emmc: delay[1]= 1200 padding= 4, bidx=1
  580. [ 3.624898@1] emmc: delay[2]= 800 padding= 1, bidx=0
  581. [ 3.624900@1] emmc: delay[3]= 1200 padding= 4, bidx=1
  582. [ 3.624902@1] emmc: delay[4]= 1200 padding= 4, bidx=1
  583. [ 3.624905@1] emmc: delay[5]= 800 padding= 1, bidx=0
  584. [ 3.624907@1] emmc: delay[6]= 1200 padding= 4, bidx=1
  585. [ 3.624910@1] emmc: delay[7]= 1200 padding= 4, bidx=1
  586. [ 3.624913@1] emmc: calibration result @ 0: max(1200), min(800)
  587. [ 3.624916@1] emmc: line_delay =0x200202, max_cal_result =1200
  588. [ 3.624918@1] emmc: base_index_max 1, base_index_min 0
  589. [ 3.624926@1] emmc: clk 100000000 SDR mode tuning start
  590. [ 3.625222@1] emmc: rx_tuning_result[0] = 10
  591. [ 3.625502@1] emmc: rx_tuning_result[1] = 10
  592. [ 3.625825@1] emmc: rx_tuning_result[2] = 10
  593. [ 3.626105@1] emmc: rx_tuning_result[3] = 10
  594. [ 3.626384@1] emmc: rx_tuning_result[4] = 10
  595. [ 3.626665@1] emmc: rx_tuning_result[5] = 10
  596. [ 3.626945@1] emmc: rx_tuning_result[6] = 10
  597. [ 3.627313@1] emmc: rx_tuning_result[7] = 10
  598. [ 3.627593@1] emmc: rx_tuning_result[8] = 10
  599. [ 3.627873@1] emmc: rx_tuning_result[9] = 10
  600. [ 3.627876@1] emmc: best_win_start =0, best_win_size =10
  601. [ 3.627880@1] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x2000
  602. [ 3.627884@1] emmc: gclock =0x100024a, gdelay=0x200202, gadjust=0x2000
  603. [ 3.628009@1] emmc: support driver strength type 1
  604. [ 3.628060@1] emmc: try set sd/emmc to DDR mode
  605. [ 3.628064@1] emmc: try set sd/emmc to DDR mode
  606. [ 3.628161@1] emmc: new HS400 MMC card at address 0001
  607. [ 3.637442@1] emmc: clock 100000000, 8-bit-bus-width
  608. [ 3.637442@1]
  609. [ 3.637442@1] mmcblk0: emmc:0001 AWPD3R 14.5 GiB
  610. [ 3.637589@1] mmcblk0boot0: emmc:0001 AWPD3R partition 1 4.00 MiB
  611. [ 3.637723@1] mmcblk0boot1: emmc:0001 AWPD3R partition 2 4.00 MiB
  612. [ 3.637864@1] mmcblk0rpmb: emmc:0001 AWPD3R partition 3 4.00 MiB
  613. [ 3.639324@1] mmcblk0: unknown partition table
  614. [ 3.640125@1] [mmc_read_partition_tbl] mmc read partition OK!
  615. [ 3.640127@1] add_emmc_partition
  616. [ 3.647212@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
  617. [ 3.647461@1] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
  618. [ 3.647643@1] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
  619. [ 3.647816@1] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
  620. [ 3.647990@1] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
  621. [ 3.648164@1] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
  622. [ 3.648350@1] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
  623. [ 3.648525@1] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
  624. [ 3.648701@1] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
  625. [ 3.648869@1] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
  626. [ 3.649048@1] [mmcblk0p11] instaboot offset 0x000034400000, size 0x000020000000
  627. [ 3.649232@1] [mmcblk0p12] boot offset 0x000054c00000, size 0x000002000000
  628. [ 3.649402@1] [mmcblk0p13] system offset 0x000057400000, size 0x000040000000
  629. [ 3.649574@1] [mmcblk0p14] data offset 0x000097c00000, size 0x00030c200000
  630. [ 3.649619@1] card key: card_blk_probe.
  631. [ 3.649624@1] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
  632. [ 3.649628@1] emmc key: emmc_key_init:552 ok.
  633. [ 3.649895@1] amlmmc_dtb_init: register dtb chardev
  634. [ 3.650009@1] amlmmc_dtb_init: register dtb chardev OK
  635. [ 3.650010@1] Exit aml_emmc_partition_ops OK.
  636. [ 3.652833@1] mmcblk0boot1: unknown partition table
  637. [ 3.653997@1] mmcblk0boot0: unknown partition table
  638. [ 3.654376@1] clear_emmc_wait_flag
  639. [ 3.971115@2] sysled: active_low = 0
  640. [ 3.974840@1] sysled: module probed ok
  641. [ 3.978877@1] pwmled: module init
  642. [ 3.981982@1] codec:Amlogic A/V streaming port init
  643. [ 3.988027@1] codec:get gate demux control ok ffffffc06381c480
  644. [ 3.992220@1] codec:get gate parser_top control ok ffffffc06381c500
  645. [ 3.998468@1] codec:get gate vpu_intr control ok ffffffc06381c580
  646. [ 4.004464@1] codec:get gate vdec control ok ffffffc06381c600
  647. [ 4.011195@1] codec:[tsync_pcr_init]init success.
  648. [ 4.014812@1] codec:amvideocap_init_module
  649. [ 4.019065@1] codec:amvideocap_probe,amvideocap
  650. [ 4.023350@1] codec:use cma buf.
  651. [ 4.026538@1] codec:amvideocap_dev_register
  652. [ 4.032872@1] amvenc_avc_probe -- reserved memory config fail.
  653. [ 4.036463@1] amvenc_avc - cma memory pool size: 40 MB
  654. [ 4.041619@1] encode_wq_init.
  655. [ 4.044482@1] encode start monitor.
  656. [ 4.048079@1] encode workqueue monitor start.
  657. [ 4.052641@1] jpegenc module init
  658. [ 4.055881@1] codec:picdec_driver_probe called.
  659. [ 4.060020@1] picdec has 1 memory regions
  660. [ 4.063991@1] codec:picdec_driver_probe done.
  661. [ 4.069436@1] codec:create_ge2d_work_queue video task ok
  662. [ 4.073974@1] codec:used fix clk for vdec clk source!
  663. [ 4.078578@1] codec:register clk_set_setting cpu[33]
  664. [ 4.083732@1] vpu_init
  665. [ 4.085794@1] The chip is not support hevc encoder
  666. [ 4.090557@1] DI: di_module_init ok.
  667. [ 4.094078@1] DI: di_module_init: major 235
  668. [ 4.098557@1] DI: di_probe
  669. [ 4.101050@1] deinterlace has 1 memory regions
  670. [ 4.105314@1] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
  671. [ 4.112911@1] di_irq:78,timerc_irq:38
  672. [ 4.116656@1] rdma_register, rdma_table_addr ffffff800017b000 rdma_table_addr_phy 74848000 reg_buf ffffffc063fd6000
  673. [ 4.126860@1] rdma_register success, handle 1 table_size 8192
  674. [ 4.132548@1] DI: di_probe allocate rdma channel 1.
  675. [ 4.137379@1] DI: DI hw version 2.
  676. [ 4.140743@1] 0x000000db:Y=db,U=0,V=0
  677. [ 4.144356@1] 0x000000dc:Y=dc,U=0,V=0
  678. [ 4.147984@1] 0x000000dd:Y=dd,U=0,V=0
  679. [ 4.151601@1] 0x000000de:Y=de,U=0,V=0
  680. [ 4.155223@1] 0x000000df:Y=df,U=0,V=0
  681. [ 4.158852@1] 0x000000e0:Y=e0,U=0,V=0
  682. [ 4.162468@1] 0x000000e1:Y=e1,U=0,V=0
  683. [ 4.166091@1] 0x000000e2:Y=e2,U=0,V=0
  684. [ 4.169719@1] 0x000000e3:Y=e3,U=0,V=0
  685. [ 4.173336@1] 0x000000f0:Y=f0,U=0,V=0
  686. [ 4.176962@1] 0x000000f1:Y=f1,U=0,V=0
  687. [ 4.180586@1] 0x000000f2:Y=f2,U=0,V=0
  688. [ 4.184204@1] 0x000000f3:Y=f3,U=0,V=0
  689. [ 4.187832@1] 0x000000f4:Y=f4,U=0,V=0
  690. [ 4.191449@1] 0x000000f5:Y=f5,U=0,V=0
  691. [ 4.195071@1] 0x000000f6:Y=f6,U=0,V=0
  692. [ 4.198700@1] 0x000000f7:Y=f7,U=0,V=0
  693. [ 4.202316@1] 0x000000f8:Y=f8,U=0,V=0
  694. [ 4.205938@1] 0x000000f9:Y=f9,U=0,V=0
  695. [ 4.209573@1] 0x000000fa:Y=fa,U=0,V=0
  696. [ 4.213183@1] 0x000000fb:Y=fb,U=0,V=0
  697. [ 4.216806@1] 0x000000fc:Y=fc,U=0,V=0
  698. [ 4.220638@1] DI: di_probe here.
  699. [ 4.223996@1] efusekeynum: 4
  700. [ 4.226475@1] efusekeyname: mac offset: 0 size: 6
  701. [ 4.232899@1] efusekeyname: mac_bt offset: 6 size: 6
  702. [ 4.239259@1] efusekeyname: mac_wifi offset: 12 size: 6
  703. [ 4.245618@1] efusekeyname: usid offset: 18 size: 16
  704. [ 4.252317@1] efuse efuse.10: probe OK!
  705. [ 4.256170@1] key unify config unifykey-num is 14
  706. [ 4.260543@1] key unify fact unifykey-num is 14
  707. [ 4.264937@1] aml_unifykeys_probe:1273=============unifykey_devno:e900000
  708. [ 4.271972@1] 6unifykey: device unifykeys created ok
  709. [ 4.276801@1] 6aml_unifykeys_init done!
  710. [ 4.280584@1] PPMGRDRV: warn: ppmgr module init func called
  711. [ 4.286201@1] PPMGRDRV: err: ppmgr_driver_probe called
  712. [ 4.291188@1] ppmgr has 1 memory regions
  713. [ 4.295062@1] PPMGRDRV: info: ppmgr_dev major:232
  714. [ 4.300008@1] PPMGRDRV: info: ppmgr_probe done
  715. [ 4.304587@1] amlogic rfkill init
  716. [ 4.307551@1] enter bt_probe of_node
  717. [ 4.310918@1] not get gpio_en
  718. [ 4.313837@1] power on valid level is high
  719. [ 4.318117@1] Bluetooth: BlueSleep Mode Driver Ver 1.2
  720. [ 4.323485@1] ionvideo-000: V4L2 device registered as video13
  721. [ 4.328718@1] ionvid: info: Video Technology Magazine Ion Video
  722. [ 4.334537@1] ionvid: info: Capture Board ver 1.0 successfully loaded
  723. [ 4.340947@1] audio_dsp: [dsp]register dsp to char divece(257)
  724. [ 4.347565@1] amaudio: amaudio: driver amaudio succuess!
  725. [ 4.352276@1] amlvid:err: amlvideo_init called
  726. [ 4.356188@1] amlvid:err: amlvideo_create_instance called
  727. [ 4.361748@1] amlvid:err: v4l2_dev.name=:amlvideo-000
  728. [ 4.366895@1] amlvideo-000: V4L2 device registered as video10
  729. [ 4.372871@1] vdin_drv_init: major 231
  730. [ 4.376463@1] vdin_drv_init: vdin driver init done
  731. [ 4.380902@1] tvafe_drv_init: major 230
  732. [ 4.385008@1] tvafe: tvafe_init.
  733. [ 4.388270@1] [RX]-hdmirx: hdmirx_init.
  734. [ 4.391639@1] ESM HLD: Initializing...
  735. [ 4.395343@1] ESM HLD: Registering device range 'esm_rx'...
  736. [ 4.400910@1] ESM HLD: Device range 'esm_rx' has been registered.
  737. [ 4.406901@1] ESM HLD: Creating class /sys/class/elliptic_rx...
  738. [ 4.412907@1] ESM HLD: The class /sys/class/elliptic_rx has been created.
  739. [ 4.419521@1] ESM HLD: Creating device 'esm_rx'...
  740. [ 4.424377@1] ESM HLD: Device 'esm_rx' has been created.
  741. [ 4.429530@1] ESM HLD: Done initializing the HLD driver.
  742. [ 4.434760@1] [viuin..]viuin_init_module viuin module init
  743. [ 4.440679@1] [viuin..]viuin_probe probe ok.
  744. [ 4.444507@1] module init
  745. [ 4.447208@1]
  746. [ 4.447208@1] VECM probe start
  747. [ 4.452088@1] aml_vecm_probe: ok
  748. [ 4.455604@1] saradc c1108680.saradc: initialized by BL30
  749. [ 4.460352@1] saradc c1108680.saradc: calibration start:
  750. [ 4.465595@1] saradc c1108680.saradc: nominal=0, value=6
  751. [ 4.470877@1] saradc c1108680.saradc: nominal=256, value=248
  752. [ 4.476461@1] saradc c1108680.saradc: nominal=512, value=496
  753. [ 4.482089@1] saradc c1108680.saradc: nominal=768, value=743
  754. [ 4.487700@1] saradc c1108680.saradc: nominal=1023, value=990
  755. [ 4.493325@1] saradc c1108680.saradc: calibration end: coef=4236
  756. [ 4.499560@1] remote: Driver init
  757. [ 4.502653@1] remote: platform_data g_remote_ao_offset=580
  758. [ 4.508021@1] remote: platform_data irq =228
  759. [ 4.512238@1] remote: set drvdata completed
  760. [ 4.516456@1] remote: device_create_file completed
  761. [ 4.521704@1] input: aml_keypad as /devices/meson-remote.12/input/input0
  762. [ 4.528325@1] remote: input_register_device completed
  763. [ 4.533223@1] remote: set_remote_mode[74]
  764. [ 4.537203@1] remote: remote config major:227
  765. [ 4.541777@1] remote: physical address:0x63cea000
  766. [ 4.546623@1] m1-adckp adc_keypad.48: adc_key: faild to get name_len!
  767. [ 4.552647@1] m1-adckp adc_keypad.48: home key(300) registed.
  768. [ 4.558528@1] input: adc_keypad as /devices/adc_keypad.48/input/input1
  769. [ 4.565404@1] gpio-key gpio_keypad.47: gpio_key: 0 name(power) pin()
  770. [ 4.571087@1] gpio-key gpio_keypad.47: amlogic_gpio_name_map_num pin 0!::
  771. [ 4.577800@1] gpio-key gpio_keypad.47: gpio_key: 0 power(147)
  772. [ 4.583485@1] gpio-key gpio_keypad.47: start setup_timer
  773. [ 4.588741@1] gpio-key gpio_keypad.47: power key(116) registed.
  774. [ 4.594842@1] input: gpio_keypad as /devices/gpio_keypad.47/input/input2
  775. [ 4.601430@1] gpio-key gpio_keypad.47: gpio keypad register input device completed.
  776. [ 4.608852@1] input input2: gpio keypad major:225
  777. [ 4.614841@1] Sensor: lsm303d_init
  778. [ 4.617143@1] Sensor: stk8313_init
  779. [ 4.620299@1] Sensor: stk831x_init
  780. [ 4.623643@1] Sensor: mxc622x_acc_init
  781. [ 4.627415@1] Sensor: mxc6255xc_acc_init
  782. [ 4.631329@1] Sensor: l3gd20_gyr_init
  783. [ 4.635850@1] aml dvb init
  784. [ 4.638039@1] Amlogic Demod DVB-T/C DebugIF Init
  785. [ 4.642226@1] Amlogic Demod DVB-T/C DebugIF Init ok----------------
  786. [ 4.649298@1] jtag: module init
  787. [ 4.651538@1] jtag: pinctrl setup apao
  788. [ 4.655043@1] jtag: set state 2
  789. efuse_pw_en: 0x3
  790. WARNING! efuse bits is disabled
  791. Enable A53 JTAG to AO
  792. [ 4.670384@0] jtag: module probed ok
  793. [ 4.670813@1] cpuinfo: probe done
  794. [ 4.671956@1] defendkey c8834500.defendkey: defendkey_devno:dd00000
  795. [ 4.678176@1] defendkey c8834500.defendkey: defendkey: device defendkey created ok
  796. [ 4.685517@1] defendkey: driver init
  797. [ 4.688908@1] input input2: key 116 up
  798. [ 4.693330@1] input: cec_input as /devices/virtual/input/input3
  799. [ 4.698774@1] cectx aocec: no hdmirx reg resource
  800. [ 4.703096@1] cectx aocec: no hhi reg resource
  801. [ 4.707620@1] cectx aocec: can't find hdmirx
  802. [ 4.712729@1] cec: wake up flag:0
  803. [ 4.715913@1] aml_aes_dma c883e000.aml_aes: Aml AES_dma
  804. [ 4.720895@1] aml_tdes_dma c883e000.aml_tdes: Aml TDES_dma
  805. [ 4.726358@1] aml_sha_dma c883e000.aml_sha: Aml SHA1/SHA224/SHA256 dma
  806. [ 4.732695@1] usbcore: registered new interface driver snd-usb-audio
  807. [ 4.739911@1] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
  808. [ 4.747639@1] aml_pcm_dai: pcm mode detection =1
  809. [ 4.750072@1] aml_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4
  810. [ 4.756759@1] aml_spdif_dai: set normal 512 fs /4 fs
  811. [ 4.761799@1] aml_audio_hw: IEC958 16bit
  812. [ 4.765540@1] hdmitx: audio: aout notify rate 48000
  813. [ 4.770392@1] hdmitx: audio: aout notify size 16
  814. [ 4.774939@1] hdmitx: audio: aout notify format CT_PCM
  815. [ 4.987297@1] aml_snd_card: headphone detection disable=1
  816. [ 4.987332@1] aml_snd_card: no spk event delay time set
  817. [ 4.992688@1] aml_snd_m8_card aml_m8_snd.46: T9015-audio-hifi <-> I2S.39 mapping ok
  818. [ 5.000320@1] aml_snd_m8_card aml_m8_snd.46: dit-hifi <-> SPDIF.40 mapping ok
  819. [ 5.006994@1] aml_pcm: enter aml_pcm_new dai->name: PCM.41 dai->id: 0
  820. [ 5.013445@1] aml_snd_m8_card aml_m8_snd.46: pcm2bt-pcm <-> PCM.41 mapping ok
  821. [ 5.020402@1] aml_snd_m8_card aml_m8_snd.46: ASoC: no source widget found for LOUTL
  822. [ 5.027961@1] aml_snd_m8_card aml_m8_snd.46: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
  823. [ 5.036737@1] aml_snd_m8_card aml_m8_snd.46: ASoC: no source widget found for LOUTR
  824. [ 5.044345@1] aml_snd_m8_card aml_m8_snd.46: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
  825. [ 5.055157@1] GACT probability NOT on
  826. [ 5.056753@1] Mirror/redirect action on
  827. [ 5.060588@1] u32 classifier
  828. [ 5.063383@1] Actions configured
  829. [ 5.066923@1] Netfilter messages via NETLINK v0.30.
  830. [ 5.071826@1] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
  831. [ 5.078535@1] ctnetlink v0.93: registering with nfnetlink.
  832. [ 5.083928@1] xt_time: kernel timezone is -0000
  833. [ 5.088020@1] ipip: IPv4 over IPv4 tunneling driver
  834. [ 5.093511@1] ip_tables: (C) 2000-2006 Netfilter Core Team
  835. [ 5.098365@1] arp_tables: (C) 2002 David S. Miller
  836. [ 5.102937@1] TCP: cubic registered
  837. [ 5.106337@1] Initializing XFRM netlink socket
  838. [ 5.112085@1] NET: Registered protocol family 10
  839. [ 5.116411@1] mip6: Mobile IPv6
  840. [ 5.118485@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
  841. [ 5.124161@1] sit: IPv6 over IPv4 tunneling driver
  842. [ 5.130181@1] NET: Registered protocol family 17
  843. [ 5.133287@1] NET: Registered protocol family 15
  844. [ 5.137999@1] Bridge firewalling registered
  845. [ 5.142054@1] Bluetooth: RFCOMM TTY layer initialized
  846. [ 5.146983@1] Bluetooth: RFCOMM socket layer initialized
  847. [ 5.152325@1] Bluetooth: RFCOMM ver 1.11
  848. [ 5.156110@1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  849. [ 5.161563@1] Bluetooth: BNEP filters: protocol multicast
  850. [ 5.166898@1] Bluetooth: BNEP socket layer initialized
  851. [ 5.172007@1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  852. [ 5.178042@1] Bluetooth: HIDP socket layer initialized
  853. [ 5.183168@1] l2tp_core: L2TP core driver, V2.0
  854. [ 5.187616@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  855. [ 5.192501@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
  856. [ 5.198291@1] l2tp_netlink: L2TP netlink interface
  857. [ 5.202972@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
  858. [ 5.209040@1] l2tp_debugfs: L2TP debugfs support
  859. [ 5.213545@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
  860. [ 5.220183@1] NET: Registered protocol family 35
  861. [ 5.224743@1] Key type dns_resolver registered
  862. [ 5.230604@1] Registering SWP/SWPB emulation handler
  863. [ 5.234652@1] regulator-dummy: disabling
  864. [ 5.238672@1] kvim_hym8563 2-0051: setting system clock to 2011-01-01 12:00:03 UTC (1293883203)
  865. [ 5.247755@1] cpufreq-scpi cpufreq-meson.7: enter cpufreq
  866. [ 5.251957@1] cpufreq-scpi cpufreq-meson.7: probe cpufreq okay
  867. [ 5.260806@0] gxbb_pm: enter meson_pm_probe!
  868. [ 5.262052@0] gxbb_pm: meson_pm_probe done
  869. [ 5.266864@0] cpucore_cooling_register, max_cpu_core_num:4
  870. [ 5.286787@0] aml_istbt_dev_ready NULL
  871. [ 5.28683 5.291520@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
  872. [ 5.294808@0] Freeing unused kernel memory: 1260K (ffffffc001ead000 - ffffffc001fe8000)
  873. [ 5.317231@1] init: init started!
  874. [ 5.318618@2] init: init second stage started!
  875. [ 5.319741@2] init: waitpid failed: No child processes
  876. [ 5.324562@2] init: (Loading properties from /default.prop took 0.00s.)
  877. [ 5.332609@2] init: (Parsing /init.environ.rc took 0.00s.)
  878. [ 5.336612@2] init: (Parsing /init.usb.rc took 0.00s.)
  879. [ 5.342565@2] init: (Parsing init.amlogic.usb.rc took 0.00s.)
  880. [ 5.347629@2] init: (Parsing init.amlogic.usb.rc took 0.00s.)
  881. [ 5.352885@2] init: (Parsing init.amlogic.board.rc took 0.01s.)
  882. [ 5.359021@2] init: (Parsing init.amlogic.usb.rc took 0.00s.)
  883. [ 5.364441@2] init: (Parsing init.amlogic.wifi.rc took 0.01s.)
  884. [ 5.370287@2] init: could not import file 'init.mtk.rc' from '/init.amlogic.rc'
  885. [ 5.377491@2] init: (Parsing /init.amlogic.rc took 0.04s.)
  886. [ 5.383254@2] init: (Parsing /init.usb.configfs.rc took 0.00s.)
  887. [ 5.388882@2] init: (Parsing /init.zygote32.rc took 0.00s.)
  888. [ 5.394360@2] init: (Parsing /init.trace.rc took 0.00s.)
  889. [ 5.399574@2] init: (Parsing /init.rc took 0.07s.)
  890. [ 5.404599@2] init: Starting service 'ueventd'...
  891. [ 5.410595@0] ueventd: ueventd started!
  892. [ 5.667312@1] ueventd: Coldboot took 0.25s.
  893. [ 5.672157@2] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
  894. [ 5.691702@2] init: enter do_confirm_formated /dev/block/tee, /tee
  895. [ 5.692255@2] init: blocksize 1024, bytes_per_inode 1024
  896. [ 5.697574@2] init: do_confirm_formated ext4 try mount
  897. [ 5.709287@2] EXT4-fs (mmcblk0p8): recovery complete
  898. [ 5.709324@2] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
  899. [ 5.775158@0] EXT4-fs (mmcblk0p13): mounted filesystem with ordered data mode. Opts: (null)
  900. [ 5.777955@0] fs_mgr: __mount(source=/dev/block/system,target=/system,type=ext4)=0
  901. [ 5.786358@0] EXT4-fs (mmcblk0p14): Ignoring removed nomblk_io_submit option
  902. [ 6.000260@0] EXT4-fs (mmcblk0p14): 2 orphan inodes deleted
  903. [ 6.000293@0] EXT4-fs (mmcblk0p14): recovery complete
  904. [ 6.011459@0] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
  905. [ 6.016643@0] fs_mgr: check_fs(): mount(/dev/block/data,/data,ext4)=0: Success
  906. [ 6.054683@2] fs_mgr: check_fs(): unmount(/data) succeeded
  907. [ 6.055544@2] fs_mgr: Running /system/bin/e2fsck on /dev/block/data
  908. [ 6.140736@2] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
  909. [ 6.140736@2]
  910. [ 6.141489@2] e2fsck: /dev/block/data: clean, 1353/799680 files, 254382/3195392 blocks
  911. [ 6.141489@2]
  912. [ 6.151626@2] EXT4-fs (mmcblk0p14): Ignoring removed nomblk_io_submit option
  913. [ 6.161022@2] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
  914. [ 6.169228@2] fs_mgr: __mount(source=/dev/block/data,target=/data,type=ext4)=0
  915. [ 6.176837@2] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
  916. [ 6.190102@2] EXT4-fs (mmcblk0p3): recovery complete
  917. [ 6.190551@2] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
  918. [ 6.200113@2] fs_mgr: check_fs(): mount(/dev/block/cache,/cache,ext4)=0: Success
  919. [ 6.258242@3] fs_mgr: check_fs(): unmount(/cache) succeeded
  920. [ 6.258309@3] fs_mgr: Running /system/bin/e2fsck on /dev/block/cache
  921. [ 6.284429@3] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
  922. [ 6.284429@3]
  923. [ 6.285170@3] e2fsck: /dev/block/cache: clean, 17/32768 files, 4212/131072 blocks
  924. [ 6.285170@3]
  925. [ 6.294903@3] EXT4-fs (mmcblk0p3): Ignoring removed nomblk_io_submit option
  926. [ 6.304001@3] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
  927. [ 6.312310@3] fs_mgr: __mount(source=/dev/block/cache,target=/cache,type=ext4)=0
  928. [ 6.320253@3] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
  929. [ 6.328742@3] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=remount-ro
  930. [ 6.337148@3] fs_mgr: check_fs(): mount(/dev/block/tee,/tee,ext4)=0: Success
  931. [ 6.398403@3] fs_mgr: check_fs(): unmount(/tee) succeeded
  932. [ 6.398467@3] fs_mgr: Running /system/bin/e2fsck on /dev/block/tee
  933. [ 6.422853@3] e2fsck: e2fsck 1.42.9 (28-Dec-2013)
  934. [ 6.422853@3]
  935. [ 6.423593@3] e2fsck: /dev/block/tee: clean, 11/8192 files, 3111/8192 blocks
  936. [ 6.423593@3]
  937. [ 6.432835@3] EXT4-fs (mmcblk0p8): Ignoring removed nomblk_io_submit option
  938. [ 6.441375@3] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: nodelalloc,nomblk_io_submit,errors=panic
  939. [ 6.450324@3] fs_mgr: __mount(source=/dev/block/tee,target=/tee,type=ext4)=0
  940. [ 6.479583@3] Adding 511996k swap on /dev/block/zram0. Priority:-1 extents:1 across:511996k SS
  941. [ 6.519187@3] EXT4-fs (zram0): mounted filesystem with ordered data mode. Opts: (null)
  942. [ 6.523992@3] init: cannot find '/system/bin/tee-supplicant', disabling 'tee_supplicant'
  943. [ 6.548238@3] init: /recovery not specified in fstab
  944. [ 6.553876@0] logd.auditd: start
  945. [ 6.553940@0] logd.klogd: 6346877335
  946. [ 6.566705@3] init: Failed to reload policy
  947. [ 6.611818@3] mali-utgard d00c0000.mali: set min pp to default 1
  948. [ 6.612193@3] mali-utgard d00c0000.mali: set min clk default to 0
  949. [ 6.618393@3] mali-utgard d00c0000.mali: max clk set 5
  950. [ 6.623329@3] mali-utgard d00c0000.mali: turbo clk set to 6
  951. [ 6.628873@3] mali-utgard d00c0000.mali: default clk set to 2
  952. [ 6.636979@0] gpu cooling register okay with err=0
  953. [ 6.639591@0] gpu core cooling register okay with err=0
  954. [ 6.644902@0] Mali: Mali device driver loaded
  955. [ 6.650572@0] random: init urandom read with 76 bits of entropy available
  956. [ 6.681220@2] dig: dig start!
  957. [ 6.691002@0] amlkey_init() enter!
  958. [ 6.696559@2] binder: 3696:3696 transaction failed 29189, size 0-0
  959. [ 6.700040@3] logd.daemon: reinit
  960. [ 6.703696@0] emmc_key_read:428, read ok
  961. [ 6.704269@0] amlkey_init() storagekey_info.buffer=ffffff8001900000, storagekey_info.size = 40000!
  962. [ 6.715299@0] vfm_map_store:rm default
  963. [ 6.716939@0] vfm_map_store:add default decoder ppmgr deinterlace amvideo
  964. [ 6.723896@0] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
  965. [ 6.733449@0] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
  966. [ 6.745809@0] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
  967. [ 6.755709@0] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
  968. [ 6.768238@0] init: property_set("ro.radio.noril", "true" failed
  969. [ 6.897391@1] CPU2: shutdown
  970. [ 6.899503@1] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
  971. [ 6.904375@1] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
  972. [ 6.916889@1] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
  973. [ 6.926669@1] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
  974. [ 6.939536@3] vout_serve: vmode set to 576cvbs
  975. [ 6.939634@1] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
  976. [ 6.939646@1] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
  977. [ 6.939660@1] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
  978. [ 6.939670@1] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
  979. [ 6.942998@1] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
  980. [ 6.943035@1] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
  981. [ 6.943597@0] fb: afbc: 1
  982. [ 6.944090@0] fb: Frame buffer memory assigned at
  983. [ 6.944090@0] fb: 0, phy: 0x000000007e000000, vir:0xffffff8002180000, size=24576K
  984. [ 6.944090@0]
  985. [ 6.944095@0] fb: ---------------clear fb0 memory ffffff8002180000
  986. [ 6.953862@1] init: cannot find '/system/bin/tee-supplicant', disabling 'tee_supplicant'
  987. [ 6.955330@1] android_usb: Cannot enable 'adb' (-22)
  988. [ 6.955708@1] android_usb: Cannot enable 'adb' (-22)
  989. [ 6.955937@0] android_usb: Cannot enable 'adb' (-22)
  990. [ 6.955938@0] fb: osd[0] canvas.idx =0x40
  991. [ 6.955939@0] fb: osd[0] canvas.addr=0x7e000000
  992. [ 6.955941@0] fb: osd[0] canvas.width=7680
  993. [ 6.955942@0] fb: osd[0] canvas.height=3240
  994. [ 6.955944@0] fb: osd[0] fram�[ 7.072693@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200
  995. [ 7.072907@3] vout_serve: don't set the same mode as current
  996. [ 7.073456@3] amhdmitx amhdmitx0: hdmitx20: stop14
  997. [ 7.073498@3] amhdmitx amhdmitx0: hdmitx20: stop22
  998. Hello Jten!!!
  999. Hello Jten!!!
  1000. Hello Jten!!!
  1001. [ 7.173691@3] remote: cur_mode = 0
  1002. [ 7.173724@3] remote: set_remote_mode[74]
  1003. [ 7.250754@3] warning: `daemonsu' uses 32-bit capabilities (legacy support in use)
  1004. [ 7.274782@0] fb: afbc: 1
  1005. [ 7.275242@0] fb: Frame buffer memory assigned at
  1006. [ 7.276274@0] fb: 1, phy: 0x000000007f800000, vir:0xffffff8003a00000, size=1024K
  1007. [ 7.276274@0]
  1008. [ 7.286076@0] fb: fb1 open, logo index:1
  1009. shell@Vim:/ $ [ 7.477323@1] fb: osd[1] enable: 0 scale:0x0 (systemcontrol)
  1010. [ 7.477359@1] fb: osd[0] enable: 1 scale:0x10001 (systemcontrol)
  1011. [ 7.505810@1] fb: free_scale_switch to fb0, mode: 0x10001
  1012. [ 7.506041@1] vout_serve: osd0=> x:0,y:0,w:1920,h:1080
  1013. [ 7.506041@1] osd1=> x:0,y:0,w:18,h:18
  1014. [ 7.537150@1] fb: current vmode=576cvbs
  1015. [ 7.545986@1] fb: osd[1] set scale, h_scale: ENABLE, v_scale: ENABLE
  1016. [ 7.546703@1] fb: osd[1].scaledata: 1920 720 1080 288
  1017. [ 7.552657@2] fb: osd[1].pandata: 0 0 0 0
  1018. [ 7.667963@2] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
  1019. [ 7.697981@2] healthd: No charger supplies found
  1020. [ 7.698025@2] healthd: No battery devices found
  1021. [ 7.700006@1] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
  1022. [ 7.876857@3] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
  1023. [ 7.917674@2] EXT4-fs (mmcblk0p13): re-mounted. Opts: (null)
  1024. [ 8.997843@0] random: nonblocking pool is initialized
  1025. [ 11.528025@0] request_suspend_state: wakeup (3->0) at 11320967795 (2011-01-01 12:00:09.789361252 UTC)
  1026. [ 11.531588@0] request_suspend_state,164,old_sleep=0,new_state=0
  1027. [ 12.729441@2] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
  1028. [ 12.730081@2] audio_dsp: last mode 0,now 0
  1029. [ 12.735750@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
  1030. [ 12.740450@1] audio_dsp: last mode 0,now 0
  1031. [ 12.745460@2] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
  1032. [ 12.750899@2] audio_dsp: last mode 0,now 0
  1033. [ 12.756577@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
  1034. [ 12.761244@0] audio_dsp: last mode 0,now 0
  1035. [ 12.782025@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
  1036. [ 12.782794@0] audio_dsp: last mode 0,now 0
  1037. [ 12.787033@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
  1038. [ 12.793179@0] audio_dsp: last mode 0,now 0
  1039. [ 12.798755@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
  1040. [ 12.803460@0] audio_dsp: last mode 0,now 0
  1041. [ 12.807879@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
  1042. [ 12.813828@0] audio_dsp: last mode 0,now 0
  1043. [ 12.968054@3] tv_vout: vout [tv_set_vframe_rate_end_hint] return mode = 7, policy = 1!
  1044. [ 12.970333@3] tv_vout: not in valid HDMI mode!
  1045. [ 16.197907@1] lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
  1046. [ 16.199603@1] lowmemorykiller: oom_adj 0 => oom_score_adj 0
  1047. [ 16.205114@1] lowmemorykiller: oom_adj 2 => oom_score_adj 117
  1048. [ 16.210842@1] lowmemorykiller: oom_adj 4 => oom_score_adj 235
  1049. [ 16.216512@1] lowmemorykiller: oom_adj 6 => oom_score_adj 352
  1050. [ 16.222237@1] lowmemorykiller: oom_adj 9 => oom_score_adj 529
  1051. [ 16.227896@1] lowmemorykiller: oom_adj 15 => oom_score_adj 1000
  1052. [ 16.981103@1] aml_wifi wifi.32: [usb_power_control] Set WiFi power down !
  1053. [ 16.982252@1] aml_wifi wifi.32: [wifi_power_ioctl] 6Set usb_sdio wifi power down!
  1054. [ 17.979266@3] avc open
  1055. [ 17.979300@3] amvenc_avc check CMA pool sucess, max instance: 2.
  1056. [ 17.982071@3] allocating phys 0x75100000, size 20480k, wq:ffffffc065569000.
  1057. [ 17.989281@3] amvenc_avc memory config sucess, buff start:0x75100000, size is 0x1400000, wq:ffffffc065569000.
  1058. [ 17.999489@3] avc release, wq:ffffffc065569000
  1059. [ 18.003921@3] remove encode_work_queue ffffffc065569000 sucess, _destroy_encode_work_queue line 4285.
  1060. [ 18.015503@3] ionvid: info: ionvideo open
  1061. [ 18.207321@3] ionvid: info: ionvideo_stop_generating!!!!
  1062. [ 18.207392@3] ionvid: info: ionvideo release
  1063. [ 18.213950@3] ionvid: info: ionvideo open
  1064. [ 18.407117@3] ionvid: info: ionvideo_stop_generating!!!!
  1065. [ 18.407201@3] ionvid: info: ionvideo release
  1066. [ 18.416807@3] ionvid: info: ionvideo open
  1067. [ 18.607114@3] ionvid: info: ionvideo_stop_generating!!!!
  1068. [ 18.607187@3] ionvid: info: ionvideo release
  1069. [ 18.615034@3] ionvid: info: ionvideo open
  1070. [ 18.807122@3] ionvid: info: ionvideo_stop_generating!!!!
  1071. [ 18.807203@3] ionvid: info: ionvideo release
  1072. [ 18.813626@3] ionvid: info: ionvideo open
  1073. [ 19.007217@2] ionvid: info: ionvideo_stop_generating!!!!
  1074. [ 19.007297@2] ionvid: info: ionvideo release
  1075. [ 19.015670@2] ionvid: info: ionvideo open
  1076. [ 19.207213@2] ionvid: info: ionvideo_stop_generating!!!!
  1077. [ 19.207288@2] ionvid: info: ionvideo release
  1078. [ 19.218314@2] ionvid: info: ionvideo open
  1079. [ 19.237345@1] libphy: stmmac-0:08 - Link is Up - 100/Full
  1080. [ 19.417199@2] ionvid: info: ionvideo_stop_generating!!!!
  1081. [ 19.417277@2] ionvid: info: ionvideo release
  1082. [ 19.432695@2] ionvid: info: ionvideo open
  1083. [ 19.627120@2] ionvid: info: ionvideo_stop_generating!!!!
  1084. [ 19.627199@2] ionvid: info: ionvideo release
  1085. [ 19.634665@2] ionvid: info: ionvideo open
  1086. [ 19.827093@2] ionvid: info: ionvideo_stop_generating!!!!
  1087. [ 19.827161@2] ionvid: info: ionvideo release
  1088. [ 19.834042@2] ionvid: info: ionvideo open
  1089. [ 20.028075@2] ionvid: info: ionvideo_stop_generating!!!!
  1090. [ 20.028157@2] ionvid: info: ionvideo release
  1091. [ 20.642157@1] avc open
  1092. [ 20.642203@1] allocating phys 0x75100000, size 20480k, wq:ffffffc03e4f7400.
  1093. [ 20.645807@1] amvenc_avc memory config sucess, buff start:0x75100000, size is 0x1400000, wq:ffffffc03e4f7400.
  1094. [ 20.657485@1] avc release, wq:ffffffc03e4f7400
  1095. [ 20.664244@1] remove encode_work_queue ffffffc03e4f7400 sucess, _destroy_encode_work_queue line 4285.
  1096. [ 21.044429@3] avc open
  1097. [ 21.044472@3] allocating phys 0x75100000, size 20480k, wq:ffffffc063534800.
  1098. [ 21.048589@3] amvenc_avc memory config sucess, buff start:0x75100000, size is 0x1400000, wq:ffffffc063534800.
  1099. [ 21.059022@3] avc release, wq:ffffffc063534800
  1100. [ 21.062906@3] remove encode_work_queue ffffffc063534800 sucess, _destroy_encode_work_queue line 4285.
  1101. [ 21.357239@3] avc open
  1102. [ 21.357311@3] allocating phys 0x75100000, size 20480k, wq:ffffffc063535400.
  1103. [ 21.360911@3] amvenc_avc memory config sucess, buff start:0x75100000, size is 0x1400000, wq:ffffffc063535400.
  1104. [ 21.371886@1] avc release, wq:ffffffc063535400
  1105. [ 21.375943@1] remove encode_work_queue ffffffc063535400 sucess, _destroy_encode_work_queue line 4285.
  1106. [ 21.690705@3] avc open
  1107. [ 21.690770@3] allocating phys 0x75100000, size 20480k, wq:ffffffc063534800.
  1108. [ 21.694403@3] amvenc_avc memory config sucess, buff start:0x75100000, size is 0x1400000, wq:ffffffc063534800.
  1109. [ 21.704616@3] avc release, wq:ffffffc063534800
  1110. [ 21.709055@3] remove encode_work_queue ffffffc063534800 sucess, _destroy_encode_work_queue line 4285.
  1111. [ 22.005777@0] avc open
  1112. [ 22.005887@0] allocating phys 0x75100000, size 20480k, wq:ffffffc03e4d6000.
  1113. [ 22.009695@0] amvenc_avc memory config sucess, buff start:0x75100000, size is 0x1400000, wq:ffffffc03e4d6000.
  1114. [ 22.019751@0] avc release, wq:ffffffc03e4d6000
  1115. [ 22.024230@0] remove encode_work_queue ffffffc03e4d6000 sucess, _destroy_encode_work_queue line 4285.
  1116. [ 22.347486@1] avc open
  1117. [ 22.347545@1] allocating phys 0x75100000, size 20480k, wq:ffffffc063d5bc00.
  1118. [ 22.351380@1] amvenc_avc memory config sucess, buff start:0x75100000, size is 0x1400000, wq:ffffffc063d5bc00.
  1119. [ 22.363798@1] avc release, wq:ffffffc063d5bc00
  1120. [ 22.365471@1] remove encode_work_queue ffffffc063d5bc00 sucess, _destroy_encode_work_queue line 4285.
  1121. [ 25.990458@1] CPU3: shutdown
  1122. [ 26.265840@0] BT_RADIO going: off
  1123. [ 26.265869@0] BCM_BT: going OFF
  1124. [ 26.287823@1] BT_RADIO going: on
  1125. [ 26.287851@1] BCM_BT: going ON
  1126. [ 26.704482@1] dig: isBootCompleted:1!
  1127. [ 26.705247@0] dig: setDataRoCount count:0!
  1128. [ 26.709145@1] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 0 to 9600
  1129. [ 26.714537@1] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 9600 to 9600
  1130. [ 26.726503@2] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 9600 to 115200
  1131. [ 26.738238@2] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 115200 to 2000000
  1132. [ 26.748427@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  1133. [ 26.748472@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  1134. [ 26.757998@1] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
  1135. [ 26.765030@1] hub 1-0:1.0: USB hub found
  1136. [ 26.766215@1] hub 1-0:1.0: 2 ports detected
  1137. [ 26.770797@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  1138. [ 26.775902@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  1139. [ 26.785546@1] hub 2-0:1.0: USB hub found
  1140. [ 26.787654@1] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
  1141. [ 26.845118@1] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
  1142. [ 26.988393@1] dwc_otg: Core Release: 3.10a
  1143. [ 26.988430@1] dwc_otg: Setting default values for core params
  1144. [ 26.992581@1] dwc_otg: curmode: 0, host_only: 0
  1145. [ 27.010150@3] dwc_otg: Using Buffer DMA mode
  1146. [ 27.011375@3] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
  1147. [ 27.014063@3] dwc_otg: Working on port type = SLAVE
  1148. [ 27.019433@3] dwc_otg: Dedicated Tx FIFOs mode
  1149. [ 27.036794@1] Number of LUNs=8
  1150. [ 27.036835@1] Mass Storage Function, version: 2009/09/11
  1151. [ 27.039616@1] LUN: removable file: (no medium)
  1152. [ 27.047375@1] android_usb gadget: android_usb ready
  1153. [ 27.052426@1] file system registered
  1154. [ 27.090355@1] ffs_data_put(): freeing
  1155. [ 27.107233@0] usb 1-1: new high-speed USB device number 2 using xhci-hcd
  1156. [ 27.125216@1] ffs_data_put(): freeing
  1157. [ 27.125990@1] android_usb: already disabled
  1158. [ 27.135340@2] read descriptors
  1159. [ 27.135386@2] read descriptors
  1160. [ 27.136230@2] read strings
  1161. [ 27.139076@2] mtp_bind_config
  1162. [ 27.170132@2] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 2000000 to 115200
  1163. [ 27.264865@0] hub 1-1:1.0: USB hub found
  1164. [ 27.264967@0] hub 1-1:1.0: 4 ports detected
  1165. [ 27.392232@2] meson_uart c11084c0.serial: ttyS1 use xtal(8M) 24000000 change 115200 to 2000000
  1166. [ 31.170374@1] CPU2: shutdown
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!