▒▒▒▒▒▒GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;
TE: 88961
no sdio debug board detected

BL2 Built : 11:44:26, Nov 25 2015.
gxb gfb13a3b-c2 - jcao@wonton

Board ID = 8
set vcck to 1100 mv
set vddee to 1050 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 same
DDR0: 2048MB(auto) @ 912MHz(2T)-13
DataBus test pass!
AddrBus test pass!
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x000000b0
Load bl30 from eMMC, src: 0x00010200, des: 0x01000000, size: 0x00009ef0
Sending bl30........................................OK.
Run bl30...
Load bl301 from eMMC, src: 0x0001c200, des: 0x01000000, size: 0x000018c0
Wait bl30...Done
Sending bl301.......OK.
Run bl301...
eMMC, src: 0x00020200, des: 0x10100000, size: 0x00011130


--- UART initialized after reboot ---
[Reset cause: unknown]
[Image: unknown, amlogic_v1.1.3046-00db630-dirty 2016-08-31 09:24:14 tao.zeng@droid04]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipLoad bl33 from eMMC, src: 0x00034200, des: 0x01000000, size: 0x0005a4a0
id: ef be ad de d f0 ad ba ef be ad de not ES chip
[0.203827 Inits done]
secure task start!
high task start!
low task start!
NOTICE:  BL3-1: v1.0(debug):4d2e34d
NOTICE:  BL3-1: Built : 17:08:35, Oct 29 2015
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2017.09-armbian (Nov 19 2017 - 09:19:22 -0800) odroid-c2

DRAM:  2 GiB
MMC:   mmc@72000: 0, mmc@74000: 1
Using default environment

In:    serial@4c0
Out:   serial@4c0
Err:   serial@4c0
Net:   eth0: ethernet@c9410000
Hit any key to stop autoboot:  0
Card did not respond to voltage select!
mmc_init: -95, time 9
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
2778 bytes read in 5 ms (542 KiB/s)
## Executing script at 1f000000
78 bytes read in 4 ms (18.6 KiB/s)
5700639 bytes read in 133 ms (40.9 MiB/s)
12304896 bytes read in 280 ms (41.9 MiB/s)
23381 bytes read in 6 ms (3.7 MiB/s)
** File not found /boot/dtb/amlogic/overlay/-fixup.scr **
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    5700575 Bytes = 5.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01000000
   Booting using the fdt blob at 0x1000000
   Loading Ramdisk to 0ea90000, end 0efffbdf ... OK
   reserving fdt memory region: addr=1000000 size=6c000
   Loading Device Tree to 000000000ea21000, end 000000000ea8ffff ... OK

Starting kernel ...

Loading, please wait...
starting version 229