Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Linux version 2.6.39.2 (nk@localhost.localdomain) (gcc version 4.5.4 20110526 (prerelease) (Linaro GCC 4.5-2011.06-0) ) #7 Mon Aug 8 01:34:22 IST 2011
- prom: fw_arg0=00000008, fw_arg1=a1f87fb0, fw_arg2=a1f88470, fw_arg3=00000004
- MyLoader: sysp=f0f0f0f0, boardp=f0f0f0f0, parts=f0f0f0f0
- bootconsole [early0] enabled
- CPU revision is: 00019374 (MIPS 24Kc)
- SoC: Atheros AR7241 rev 1
- Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
- Determined physical RAM map:
- memory: 02000000 @ 00000000 (usable)
- Initrd not found or empty - disabling initrd
- Zone PFN ranges:
- Normal 0x00000000 -> 0x00002000
- Movable zone start PFN for each node
- early_node_map[1] active PFN ranges
- 0: 0x00000000 -> 0x00002000
- On node 0 totalpages: 8192
- free_area_init_node: node 0, pgdat 802c9280, node_mem_map 81000000
- Normal zone: 64 pages used for memmap
- Normal zone: 0 pages reserved
- Normal zone: 8128 pages, LIFO batch:0
- pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- pcpu-alloc: [0] 0
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- Kernel command line: board=TL-WR741ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
- PID hash table entries: 128 (order: -3, 512 bytes)
- Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- Writing ErrCtl register=00000000
- Readback ErrCtl register=00000000
- Memory: 29304k/32768k available (2066k kernel code, 3464k reserved, 403k data, 176k init, 0k highmem)
- SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- NR_IRQS:80
- Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- MIPS: machine is TP-LINK TL-WR741ND
- registering PCI controller with io_map_base unset
- bio: create slab <bio-0> at 0
- pci 0000:00:00.0: [168c:ff1c] type 0 class 0x000200
- pci 0000:00:00.0: fixup device configuration
- pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
- pci 0000:00:00.0: supports D1
- pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- pci 0000:00:00.0: PME# disabled
- pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
- pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff 64bit] (PCI address [0x10000000-0x1000ffff])
- PCI: mapping irq 72 to pin1@0000:00:00.0
- Switching to clocksource MIPS
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- TCP: Hash tables configured (established 1024 bind 1024)
- TCP reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- PCI: CLS 0 bytes, default 32
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- msgmni has been set to 57
- io scheduler noop registered
- io scheduler deadline registered (default)
- Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
- console [ttyS0] enabled, bootconsole disabled
- Atheros AR71xx SPI Controller driver version 0.2.4
- m25p80 spi0.0: found s25sl032a, expected m25p80
- m25p80 spi0.0: s25sl032a (4096 Kbytes)
- spi0.0: searching for MyLoader partition table at offset 0x10000
- spi0.0: searching for MyLoader partition table at offset 0x20000
- spi0.0: searching for MyLoader partition table at offset 0x30000
- spi0.0: searching for MyLoader partition table at offset 0x40000
- spi0.0: no MyLoader partition table found
- Searching for RedBoot partition table in spi0.0 at offset 0x3e0000
- Searching for RedBoot partition table in spi0.0 at offset 0x3f0000
- No RedBoot partition table detected in spi0.0
- spi0.0: no WRT160NL signature found
- Creating 5 MTD partitions on "spi0.0":
- 0x000000000000-0x000000020000 : "u-boot"
- 0x000000020000-0x000000160000 : "kernel"
- 0x000000160000-0x0000003f0000 : "rootfs"
- mtd: partition "rootfs" set to be root filesystem
- mtd: partition "rootfs_data" created automatically, ofs=3B0000, len=40000
- 0x0000003b0000-0x0000003f0000 : "rootfs_data"
- 0x0000003f0000-0x000000400000 : "art"
- 0x000000020000-0x0000003f0000 : "firmware"
- ag71xx_mdio: probed
- eth0: Atheros AG71xx at 0xba000000, irq 5
- eth0: Found an AR7240 built-in switch
- eth1: Atheros AG71xx at 0xb9000000, irq 4
- eth1: connected to PHY at ag71xx-mdio:04 [uid=004dd041, driver=Generic PHY]
- Atheros AR71xx hardware watchdog driver version 0.1.0
- ar71xx-wdt: timeout=15 secs (max=21)
- nf_conntrack version 0.5.0 (457 buckets, 1828 max)
- TCP westwood registered
- NET: Registered protocol family 17
- Bridge firewalling registered
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- Freeing unused kernel memory: 176k freed
- input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
- Button Hotplug driver version 0.4.1
- Registered led device: tl-wr741nd:green:system
- Registered led device: tl-wr741nd:green:qss
- eth0: link up (1000Mbps/Full duplex)
- eth0: link down
- NET: Registered protocol family 10
- ADDRCONF(NETDEV_UP): eth0: link is not ready
- eth0: link up (1000Mbps/Full duplex)
- ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- Compat-wireless backport release: compat-wireless-2011-06-23
- Backport based on wireless-testing.git master-2011-06-22
- cfg80211: Calling CRDA to update world regulatory domain
- cfg80211: World regulatory domain updated:
- cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- PCI: Setting latency timer of device 0000:00:00.0 to 64
- ath: EEPROM regdomain: 0x0
- ath: EEPROM indicates default country code should be used
- ath: doing EEPROM country->regdmn map search
- ath: country maps to regdmn code: 0x3a
- ath: Country alpha2 being used: US
- ath: Regpair used: 0x3a
- ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- Registered led device: ath9k-phy0
- ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=72
- cfg80211: Calling CRDA for country: US
- PPP generic driver version 2.4.2
- IPv6 over IPv4 tunneling driver
- GRE over IPv4 demultiplexor driver
- GRE over IPv4 tunneling driver
- ip_tables: (C) 2000-2006 Netfilter Core Team
- cfg80211: Regulatory domain changed to country: US
- cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- cfg80211: (2312000 KHz - 2502000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (2474000 KHz - 2600000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (4910000 KHz - 4950000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (4930000 KHz - 4970000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (5030000 KHz - 5070000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (5050000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 3500 mBm)
- NET: Registered protocol family 24
- xt_time: kernel timezone is -0000
- xt_ipp2p: Unknown symbol HX_memmem (err 0)
- ip6_tables: (C) 2000-2006 Netfilter Core Team
- jffs2: Too few erase blocks (4)
- ar71xx-wdt: enabling watchdog timer
- ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
- eth0: link down
- ADDRCONF(NETDEV_UP): eth0: link is not ready
- eth0: link down
- ADDRCONF(NETDEV_UP): eth0: link is not ready
- eth0: link up (1000Mbps/Full duplex)
- ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- ADDRCONF(NETDEV_UP): wlan0: link is not ready
- root@Nettlynx-cpeMAX-N:/tmp/root/etc/config#
- root@Nettlynx-cpeMAX-N:/tmp/root/etc/config# dmesg
- Linux version 2.6.39.2 (nk@localhost.localdomain) (gcc version 4.5.4 20110526 (prerelease) (Linaro GCC 4.5-2011.06-0) ) #7 Mon Aug 8 01:34:22 IST 2011
- prom: fw_arg0=00000008, fw_arg1=a1f87fb0, fw_arg2=a1f88470, fw_arg3=00000004
- MyLoader: sysp=f0f0f0f0, boardp=f0f0f0f0, parts=f0f0f0f0
- bootconsole [early0] enabled
- CPU revision is: 00019374 (MIPS 24Kc)
- SoC: Atheros AR7241 rev 1
- Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
- Determined physical RAM map:
- memory: 02000000 @ 00000000 (usable)
- Initrd not found or empty - disabling initrd
- Zone PFN ranges:
- Normal 0x00000000 -> 0x00002000
- Movable zone start PFN for each node
- early_node_map[1] active PFN ranges
- 0: 0x00000000 -> 0x00002000
- On node 0 totalpages: 8192
- free_area_init_node: node 0, pgdat 802c9280, node_mem_map 81000000
- Normal zone: 64 pages used for memmap
- Normal zone: 0 pages reserved
- Normal zone: 8128 pages, LIFO batch:0
- pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- pcpu-alloc: [0] 0
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- Kernel command line: board=TL-WR741ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
- PID hash table entries: 128 (order: -3, 512 bytes)
- Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- Writing ErrCtl register=00000000
- Readback ErrCtl register=00000000
- Memory: 29304k/32768k available (2066k kernel code, 3464k reserved, 403k data, 176k init, 0k highmem)
- SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- NR_IRQS:80
- Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
- pid_max: default: 32768 minimum: 301
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- MIPS: machine is TP-LINK TL-WR741ND
- registering PCI controller with io_map_base unset
- bio: create slab <bio-0> at 0
- pci 0000:00:00.0: [168c:ff1c] type 0 class 0x000200
- pci 0000:00:00.0: fixup device configuration
- pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
- pci 0000:00:00.0: supports D1
- pci 0000:00:00.0: PME# supported from D0 D1 D3hot
- pci 0000:00:00.0: PME# disabled
- pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
- pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff 64bit] (PCI address [0x10000000-0x1000ffff])
- PCI: mapping irq 72 to pin1@0000:00:00.0
- Switching to clocksource MIPS
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- TCP: Hash tables configured (established 1024 bind 1024)
- TCP reno registered
- UDP hash table entries: 256 (order: 0, 4096 bytes)
- UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- NET: Registered protocol family 1
- PCI: CLS 0 bytes, default 32
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- msgmni has been set to 57
- io scheduler noop registered
- io scheduler deadline registered (default)
- Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
- serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
- console [ttyS0] enabled, bootconsole disabled
- Atheros AR71xx SPI Controller driver version 0.2.4
- m25p80 spi0.0: found s25sl032a, expected m25p80
- m25p80 spi0.0: s25sl032a (4096 Kbytes)
- spi0.0: searching for MyLoader partition table at offset 0x10000
- spi0.0: searching for MyLoader partition table at offset 0x20000
- spi0.0: searching for MyLoader partition table at offset 0x30000
- spi0.0: searching for MyLoader partition table at offset 0x40000
- spi0.0: no MyLoader partition table found
- Searching for RedBoot partition table in spi0.0 at offset 0x3e0000
- Searching for RedBoot partition table in spi0.0 at offset 0x3f0000
- No RedBoot partition table detected in spi0.0
- spi0.0: no WRT160NL signature found
- Creating 5 MTD partitions on "spi0.0":
- 0x000000000000-0x000000020000 : "u-boot"
- 0x000000020000-0x000000160000 : "kernel"
- 0x000000160000-0x0000003f0000 : "rootfs"
- mtd: partition "rootfs" set to be root filesystem
- mtd: partition "rootfs_data" created automatically, ofs=3B0000, len=40000
- 0x0000003b0000-0x0000003f0000 : "rootfs_data"
- 0x0000003f0000-0x000000400000 : "art"
- 0x000000020000-0x0000003f0000 : "firmware"
- ag71xx_mdio: probed
- eth0: Atheros AG71xx at 0xba000000, irq 5
- eth0: Found an AR7240 built-in switch
- eth1: Atheros AG71xx at 0xb9000000, irq 4
- eth1: connected to PHY at ag71xx-mdio:04 [uid=004dd041, driver=Generic PHY]
- Atheros AR71xx hardware watchdog driver version 0.1.0
- ar71xx-wdt: timeout=15 secs (max=21)
- nf_conntrack version 0.5.0 (457 buckets, 1828 max)
- TCP westwood registered
- NET: Registered protocol family 17
- Bridge firewalling registered
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- Freeing unused kernel memory: 176k freed
- input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
- Button Hotplug driver version 0.4.1
- Registered led device: tl-wr741nd:green:system
- Registered led device: tl-wr741nd:green:qss
- eth0: link up (1000Mbps/Full duplex)
- eth0: link down
- NET: Registered protocol family 10
- ADDRCONF(NETDEV_UP): eth0: link is not ready
- eth0: link up (1000Mbps/Full duplex)
- ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- Compat-wireless backport release: compat-wireless-2011-06-23
- Backport based on wireless-testing.git master-2011-06-22
- cfg80211: Calling CRDA to update world regulatory domain
- cfg80211: World regulatory domain updated:
- cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- PCI: Setting latency timer of device 0000:00:00.0 to 64
- ath: EEPROM regdomain: 0x0
- ath: EEPROM indicates default country code should be used
- ath: doing EEPROM country->regdmn map search
- ath: country maps to regdmn code: 0x3a
- ath: Country alpha2 being used: US
- ath: Regpair used: 0x3a
- ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- Registered led device: ath9k-phy0
- ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=72
- cfg80211: Calling CRDA for country: US
- PPP generic driver version 2.4.2
- IPv6 over IPv4 tunneling driver
- GRE over IPv4 demultiplexor driver
- GRE over IPv4 tunneling driver
- ip_tables: (C) 2000-2006 Netfilter Core Team
- cfg80211: Regulatory domain changed to country: US
- cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- NET: Registered protocol family 24
- xt_time: kernel timezone is -0000
- xt_ipp2p: Unknown symbol HX_memmem (err 0)
- ip6_tables: (C) 2000-2006 Netfilter Core Team
- jffs2: Too few erase blocks (4)
- ar71xx-wdt: enabling watchdog timer
- ADDRCONF(NETDEV_UP): tmp.radio0: link is not ready
- eth0: link down
- ADDRCONF(NETDEV_UP): eth0: link is not ready
- eth0: link down
- ADDRCONF(NETDEV_UP): eth0: link is not ready
- eth0: link up (1000Mbps/Full duplex)
- ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
- ADDRCONF(NETDEV_UP): wlan0: link is not ready
Add Comment
Please, Sign In to add comment