Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.09.28 12:39:08 =~=~=~=~=~=~=~=~=~=~=~=
- j
- TE : 33267
- BT : 19:49:35 Jul 29 2015
- PMU:rn5t618
- DC01 v:1100, 0x[36]: 18 -> 28
- DC02 v:1150, 0x[37]: 18 -> 2c
- DC03 v:1500, 0x[38]: 38 -> 48
- LDO01 v:2900, 0x[4c]: 4e -> 50
- LDO02 v:1800, 0x[4d]: 24 -> 24
- LDO03 v:1800, 0x[4e]: 30 -> 30
- LDO04 v:2850, 0x[4f]: 4e -> 4e
- LDO05 v:1800, 0x[50]: 24 -> 24
- LDO0a v:2700, 0x[56]: 28 -> 28
- LDO0b v:900, 0x[57]: 00 -> 00
- CPU clock is 1200MHz
- CPU type: M8
- DDR info: 2GB(auto) @ 792MHz(1T)
- DDR channel: DDR 0 + DDR 1
- DDR init use : 12101 us
- HHH
- Boot From SPI
- ucl decompress...pass
- 0x12345678
- Boot from internal device 1st SPI
- TE : 397556
- System Started
- U-boot-00000-gd05fbcd-dirty(m8_k200_v1@dualboot) (Jul 29 2015 - 19:49:24)
- clr h-ram
- DRAM: 2 GiB
- relocation Offset is: 6fec0000
- show partition table:
- part: 0, name : logo, size : 2000000
- part: 1, name : recovery, size : 2000000
- part: 2, name : misc, size : 1000000
- part: 3, name : boot, size : 1000000
- part: 4, name : linuxk, size : 1000000
- part: 5, name : system, size : 40000000
- part: 6, name : cache, size : 20000000
- part: 7, name : data, size : end
- aml_card_type=0x100
- MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
- [mmc_register] add mmc dev_num=1, port=2, if_type=6
- SDIO Port B: 0, SDIO Port C: 1
- PMU fault status:
- reg[0x9A] = 0x1d
- LSI version:04, OTP version:0c
- PMU type:RN5T618
- register usb cfg[0][1] = 7ff6fdd4
- register usb cfg[2][0] = 7ff7331c
- NAND: SPI BOOT: boot_device_flag 0
- Nand PHY driver Version: 1.01.001.0004 (c) 2013 Amlogic Inc.
- amlnf_phy_init : amlnf init flag 0
- NAND device id: ad de 94 da 74 c4 ad de
- detect NAND device: A revision 20nm NAND 8GiB H27UCG8T2A
- nand chip ce mask 1
- AML_NAND_NEW_OOB : new oob
- bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
- hynix nand get default reg value at blk:8, page:2048
- NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 0
- NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
- NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 50
- i=0,register --- nand_key
- nfcache : offset: 0x000006000000 -0x000024800000 : partitons 1 : single_chip multi_plane
- nfcode : offset: 0x00002a800000 -0x00004f800000 : partitons 6 : single_chip multi_plane
- nfdata : offset: 0x00007a000000 -0x000186000000 : partitons 1 : single_chip multi_plane
- bad block count = 0
- bad block count = 0
- bad block count = 0
- amlnf_logic_init: START
- amlnf_logic_init: COMPLETE
- get_boot_device_flag: init_ret 0
- get_boot_device_flag SPI BOOT:
- nand init success, change the device_boot_flag to 4 : spi+nand
- SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
- SF: Detected MX25L1605D with page size 256, total 2 MiB
- SPI NOR Flash have write protect!!!
- set_storage_device_flag: store 4
- vpu driver detect cpu type: m8
- vpu clk_level in dts: 7
- set vpu clk: 364300000Hz, readback: 364300000Hz(0x700)
- Net: Meson_Ethernet
- init suspend firmware done. (ret:0)
- cvbs trimming.1.v5: 0xa0, 0x0
- charging
- start charging
- wipe_data=successful
- wipe_cache=successful
- reboot_mode=charging
- mode = 8 vic = 16
- set HDMI vic: 16
- config HPLL
- config HPLL done
- reconfig packet setting done
- Hit Enter key to stop autoboot -- : 1 0
- exit abortboot: 0
- current storer:nand_key
- key save is auto select storer(nand or emmc)
- write key code version3_flush:708,prov->write:7fee8dd8
- size:4096
- arg_pages:1
- extra_page:0
- write key ok!!
- Booting...
- mac is: :00:01:db:88:06:e4
- ## ANDROID Format IMAGE
- ## Booting kernel from Legacy Image at 12000000 ...
- Image Name: Linux-3.10.86
- Image Type: ARM Linux Kernel Image (lzo compressed)
- Data Size: 6658024 Bytes = 6.3 MiB
- Load Address: 00208000
- Entry Point: 00208000
- Verifying Checksum ... OK
- Ramdisk start addr = 0x1265a800, len = 0x31d600
- Flat device tree start addr = 0x12978000, len = 0x47b4 magic=0xedfe0dd0
- Uncompressing Kernel Image ... OK
- uboot time: 2232574 us.
- EFUSE machid is not set.
- Using machid 0xf81 from environment
- From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x5326001
- Loading Ramdisk to 05008000, end 05325600 ... OK
- Loading Device Tree to 05000000, end 050077b3 ... OK
- Starting kernel ...
- [ 0.000000@0] Booting Linux on physical CPU 0x200
- [ 0.000000@0] Linux version 3.10.86 (user@Debian) (gcc version 4.9.2 (GCC) ) #1 SMP PREEMPT Fri Sep 25 21:24:05 MSK 2015
- [ 0.000000@0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
- [ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000@0] Machine: Amlogic Meson8, model: AMLOGIC
- [ 0.000000@0] physical memory start address is 0x200000
- [ 0.000000@0] reserved_end is 1f1fffff
- [ 0.000000@0]
- [ 0.000000@0] Total memory is 2046 MiB
- [ 0.000000@0] Reserved low memory from 0x06000000 to 0x1f1fffff, size: 402 MiB
- [ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x0a900000 ( 72 MiB)
- [ 0.000000@0] mesonfb1(low) : 0x0a900000 - 0x0aa00000 ( 1 MiB)
- [ 0.000000@0] deinterlace0(high) : 0x7df00000 - 0x80000000 ( 33 MiB)
- [ 0.000000@0] mesonstream0(low) : 0x0aa00000 - 0x0ca00000 ( 32 MiB)
- [ 0.000000@0] vdec0(low) : 0x0ca00000 - 0x1ca00000 (256 MiB)
- [ 0.000000@0] ppmgr0(high) : 0x7cf00000 - 0x7df00000 ( 16 MiB)
- [ 0.000000@0] vdin10(low) : 0x1ca00000 - 0x1da00000 ( 16 MiB)
- [ 0.000000@0] amlvideo20(low) : 0x1da00000 - 0x1f200000 ( 24 MiB)
- [ 0.000000@0] get storage device: storage 4
- [ 0.000000@0] value=4
- [ 0.000000@0] get_storage_device : get storage device: storage 4
- [ 0.000000@0] get_storage_device : value=4
- [ 0.000000@0] [get_storage_device] storage_flag=4
- [ 0.000000@0] [get_storage_device] the storage device does NOT relate to eMMC, storage_flag=4
- [ 0.000000@0] cma: CMA: reserved 8 MiB at 2f000000
- [ 0.000000@0] cma: Found region@0, memory base 0, size 18 MiB
- [ 0.000000@0] cma: CMA: reserved 20 MiB at 2dc00000
- [ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000@0] Meson chip version = RevC (19:C - 0:27ED)
- [ 0.000000@0] PERCPU: Embedded 8 pages/cpu @c1e72000 s12288 r8192 d12288 u32768
- [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 403216
- [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200n8 no_console_suspend storage=4 cvbsdrv=0 vdaccfg=0xa000 reboot_args=uboot_suspend logo=osd1,loaded,0x15100000,1080p,full hdmimode=1080p cvbsmode=576cvbs androidboot.firstboot=0 hdmitx= mac=00:01:db:88:06:e4 hdmitx=cecf boot=/dev/system disk=/dev/data BOOT_IMAGE=/dev/linuxk scaling_governor=ondemand scaling_min_freq=96000 scaling_max_freq=1608000 ssh
- [ 0.000000@0] cvbs performance line = 0
- [ 0.000000@0] cvbs trimming line = 0xa000
- [ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
- [ 0.000000@0] osd1:1
- [ 0.000000@0] loaded:268435459
- [ 0.000000@0] logo has been loaded
- [ 0.000000@0] 1080p:15
- [ 0.000000@0] full:2
- [ 0.000000@0] kernel get hdmimode form uboot is 1080p
- [ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
- [ 0.000000@0] ******** uboot setup mac-addr: 0:1:db:88:6:e4
- [ 0.000000@0] hdmitx: cec: Function List: enable, one touch play, one touch standby, auto power by tv
- [ 0.000000@0] hdmitx: cec: HDMI aml_read_reg32(P_AO_DEBUG_REG0):0xf
- [ 0.000000@0] hdmitx: cec: HDMI hdmi_cec_func_config:0xf
- [ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000@0] Memory: 64MB 16MB 1501MB = 1581MB total
- [ 0.000000@0] Memory: 1555264k/1555264k available, 63680k reserved, 1266688K highmem
- [ 0.000000@0] Virtual kernel memory layout:
- [ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
- [ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
- [ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000@0] .text : 0xc0008000 - 0xc0b437ac (11502 kB)
- [ 0.000000@0] .init : 0xc0b44000 - 0xc0b9d000 ( 356 kB)
- [ 0.000000@0] .data : 0xc0b9e000 - 0xc0c4d610 ( 702 kB)
- [ 0.000000@0] .bss : 0xc0c4d610 - 0xc0ebfbac (2506 kB)
- [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000@0] Preemptible hierarchical RCU implementation.
- [ 0.000000@0] NR_IRQS:256
- [ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
- [ 0.000000@0] Switching to timer-based delay loop
- [ 0.000000@0] Console: colour dummy device 80x30
- [ 0.000000@0] console [ttyS0] enabled
- [ 0.403793@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
- [ 0.414089@0] pid_max: default: 32768 minimum: 301
- [ 0.418954@0] Security Framework initialized
- [ 0.423183@0] Mount-cache hash table entries: 512
- [ 0.430788@0] CPU: Testing write buffer coherency: ok
- [ 0.433079@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
- [ 0.438649@0] Setting up static identity map for 0xc07e0990 - 0xc07e09e8
- [ 0.445421@0] L310 cache controller enabled
- [ 0.449454@0] l2x0: 8 ways, 4096 sets, CACHE_ID 0x4100a0c9, Cache size: 1048576 B
- [ 0.457025@0] AUX_CTRL 0x7ec80001, PERFETCH_CTRL 0x71000007, POWER_CTRL 0x00000000
- [ 0.465147@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
- [ 0.550126@0] write pen_release: 1
- [ 0.550303@1] CPU1: Booted secondary processor
- [ 0.550315@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
- [ 0.570124@0] write pen_release: 2
- [ 0.578262@2] CPU2: Booted secondary processor
- [ 0.578276@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
- [ 0.590124@0] write pen_release: 3
- [ 0.598265@3] CPU3: Booted secondary processor
- [ 0.598277@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
- [ 0.598342@0] Brought up 4 CPUs
- [ 0.611475@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
- [ 0.617705@0] CPU: All CPU(s) started in SVC mode.
- [ 0.622921@0] devtmpfs: initialized
- [ 0.631254@0] clkrate [ xtal ] : 24000000
- [ 0.631283@0] clkrate [ pll_sys ] : 1200000000
- [ 0.634523@0] clkrate [ pll_fixed ] : 2550000000
- [ 0.639203@0] clkrate [ pll_vid ] : 366000000
- [ 0.643630@0] TODO: clk_get_rate_hpll() is not implement in M8 now
- [ 0.649777@0] clkrate [ pll_hpll ] : 0
- [ 0.653596@0] clkrate [ pll_ddr ] : 0
- [ 0.657320@0] clkrate [ a9_clk ] : 1200000000
- [ 0.661745@0] clkrate [ clk81 ] : 141666666
- [ 0.667008@0] pinctrl core: initialized pinctrl subsystem
- [ 0.671679@0] regulator-dummy: no parameters
- [ 0.676475@0] NET: Registered protocol family 16
- [ 0.686567@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
- [ 0.690204@0] VPU driver version: v03
- [ 0.691700@0] vpu driver detect cpu type: m8
- [ 0.695949@0] load vpu_clk in dts: 364300000Hz(7)
- [ 0.700697@0] vpu_probe OK
- [ 0.703783@0] cma: Assigned CMA region with name cma_0 to amvenc_avc.0 device
- [ 0.714495@0] amlogic_gpio gpio: Probed amlogic GPIO driver
- [ 0.716181@0] register lm device lm-root
- [ 0.719955@0] register lm device lm1
- [ 0.723520@0] register lm device lm0
- [ 0.727198@0] Init pinux probe!
- [ 0.730501@0] pinmux-m8 pinmux: Probed amlogic pinctrl driver
- [ 0.735889@0] tv_init_module
- [ 0.738687@0] major number 254 for disp
- [ 0.742507@0] vout_register_server
- [ 0.745877@0] register tv module server ok
- [ 0.750031@0] major number 0 for disp
- [ 0.753678@0] register tv module server ok
- [ 0.757988@0] video2_early_init enter
- [ 0.761574@0] video2_early_init exit
- [ 0.765149@0] aml_i2c version: 20140813
- [ 0.769122@0] aml-i2c i2c-AO: add adapter aml_i2c_adap0(ed80e0a8)
- [ 0.775017@0] aml-i2c i2c-AO: aml i2c bus driver.
- [ 0.779868@0] aml-i2c i2c-A: add adapter aml_i2c_adap1(ed80d4a8)
- [ 0.785676@0] aml-i2c i2c-A: aml i2c bus driver.
- [ 0.790472@0] aml-i2c i2c-B: add adapter aml_i2c_adap2(ed80c8a8)
- [ 0.796241@0] aml-i2c i2c-B: aml i2c bus driver.
- [ 0.801032@0] aml-i2c i2c-C: add adapter aml_i2c_adap3(ed80dca8)
- [ 0.806816@0] aml-i2c i2c-C: aml i2c bus driver.
- [ 0.811572@0] aml_pmu_init, 454
- [ 0.814597@0] call aml_dvfs_init in
- [ 0.818249@0] hdmitx: system: amhdmitx_init
- [ 0.822166@0] hdmitx: system: Ver: 2014May6
- [ 0.826384@0] hdmitx: system: amhdmitx_probe
- [ 0.830804@0] hdmitx: system: not find cec config
- [ 0.835246@0] hdmitx: system: not find vend_init_data
- [ 0.840549@0] hdmitx: system: gate/pwr cmd: 7
- [ 0.844609@0] hdmitx: system: ALREADY init VIC = 16
- [ 0.849461@0] hdmitx: system: gate/pwr cmd: 0
- [ 0.854185@1] hdmitx: system: reset intr mask
- [ 0.870362@0] hdmitx: system: irq 1
- [ 0.922001@0] bio: create slab <bio-0> at 0
- [ 0.922759@0] SCSI subsystem initialized
- [ 0.924804@0] usbcore: registered new interface driver usbfs
- [ 0.930174@0] usbcore: registered new interface driver hub
- [ 0.935635@0] usbcore: registered new device driver usb
- [ 0.941466@0] Linux video capture interface: v2.00
- [ 0.945736@0] pps_core: LinuxPPS API ver. 1 registered
- [ 0.950637@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.959960@0] PTP clock support registered
- [ 0.964645@0] mode is 15,sync_duration_den=1,sync_duration_num=60
- [ 0.970059@0] TV mode 1080p selected.
- [ 0.973685@0] already display in uboot
- [ 0.979536@0] call aml_pmu_probe_init in
- [ 0.981378@0] aml_pmus_probe, child name:rn5t618
- [ 0.985908@0] aml_pmus_probe, i2c_bus:i2c_bus_ao
- [ 0.990690@1] hdmitx: system: gate/pwr cmd: 4
- [ 0.990851@0] [RICOH]setup_supply_data, failed to get property: board_battery
- [ 0.991760@0] Allocate new i2c device: adapter:0, addr:0x32, node name:rn5t618, type:ricoh_pmu
- [ 0.992159@0] Advanced Linux Sound Architecture Driver Initialized.
- [ 0.992624@0] Bluetooth: Core ver 2.16
- [ 0.992707@0] NET: Registered protocol family 31
- [ 0.992709@0] Bluetooth: HCI device and connection manager initialized
- [ 0.992717@0] Bluetooth: HCI socket layer initialized
- [ 0.992721@0] Bluetooth: L2CAP socket layer initialized
- [ 0.992734@0] Bluetooth: SCO socket layer initialized
- [ 0.992974@0] cfg80211: Calling CRDA to update world regulatory domain
- [ 1.054409@0] Switching to clocksource Timer-E
- [ 1.078066@0] NET: Registered protocol family 2
- [ 1.078578@0] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.084198@0] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.090797@0] TCP: Hash tables configured (established 4096 bind 4096)
- [ 1.097283@0] TCP: reno registered
- [ 1.100642@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.106617@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.113158@0] NET: Registered protocol family 1
- [ 1.117694@0] RPC: Registered named UNIX socket transport module.
- [ 1.123610@0] RPC: Registered udp transport module.
- [ 1.128461@0] RPC: Registered tcp transport module.
- [ 1.133304@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.139960@0] wifi_dev_probe
- [ 1.142754@0] wifi_dt : interrupt_pin=GPIOX_21
- [ 1.147182@0] wifi_dt : irq_num=null
- [ 1.150735@0] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
- [ 1.155842@0] wifi_dt : power_on_pin=GPIOAO_6
- [ 1.160197@0] wifi_dt : power_on_pin2=GPIOX_11
- [ 1.164604@0] interrupt_pin=133, irq_num=4, irq_trigger_type=0, power_on_pin=6,clock_32k_pin=122
- [ 1.173532@0] Unpacking initramfs...
- [ 1.184744@0] Freeing initrd memory: 3188K (c4e08000 - c5125000)
- [ 1.187009@0] audit: initializing netlink socket (disabled)
- [ 1.190698@0] type=2000 audit(1.090:1): initialized
- [ 1.195965@0] bounce pool size: 64 pages
- [ 1.204561@0] VFS: Disk quotas dquot_6.5.2
- [ 1.204783@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 1.211848@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 1.217292@0] NFS: Registering the id_resolver key type
- [ 1.221381@0] Key type id_resolver registered
- [ 1.225680@0] Key type id_legacy registered
- [ 1.230250@0] fuse init (API version 7.22)
- [ 1.234442@0] msgmni has been set to 625
- [ 1.238842@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
- [ 1.245364@0] io scheduler noop registered
- [ 1.249461@0] io scheduler deadline registered
- [ 1.253997@0] io scheduler cfq registered (default)
- [ 1.258130@1] hdmitx: system: gate/pwr cmd: 5
- [ 1.258132@1] hdmitx: edid: edid ready
- [ 1.258133@1] hdmitx: system: gate/pwr cmd: 4
- [ 1.274389@0] loop: module loaded
- [ 1.275128@0] tun: Universal TUN/TAP device driver, 1.6
- [ 1.279615@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 1.286063@0] PPP generic driver version 2.4.2
- [ 1.290545@0] PPP BSD Compression module registered
- [ 1.295204@0] PPP Deflate Compression module registered
- [ 1.300414@0] PPP MPPE Compression module registered
- [ 1.305342@0] NET: Registered protocol family 24
- [ 1.310062@0] usbcore: registered new interface driver asix
- [ 1.315596@0] usbcore: registered new interface driver ax88179_178a
- [ 1.321818@0] usbcore: registered new interface driver cdc_ether
- [ 1.327779@0] usbcore: registered new interface driver dm9601
- [ 1.333514@0] usbcore: registered new interface driver net1080
- [ 1.339319@0] usbcore: registered new interface driver cdc_subset
- [ 1.345380@0] usbcore: registered new interface driver zaurus
- [ 1.351126@0] usbcore: registered new interface driver cdc_ncm
- [ 1.357216@0] usbcore: registered new interface driver usb-storage
- [ 1.363268@0] mousedev: PS/2 mouse device common for all mice
- [ 1.368829@0] i2c /dev entries driver
- [ 1.373074@0] lirc_dev: IR Remote Control driver registered, major 246
- [ 1.378948@0] IR NEC protocol handler initialized
- [ 1.383614@0] IR RC5(x) protocol handler initialized
- [ 1.388562@0] IR RC6 protocol handler initialized
- [ 1.393236@0] IR JVC protocol handler initialized
- [ 1.397926@0] IR Sony protocol handler initialized
- [ 1.402684@0] IR RC5 (streamzap) protocol handler initialized
- [ 1.408411@0] IR SANYO protocol handler initialized
- [ 1.413262@0] IR MCE Keyboard/mouse protocol handler initialized
- [ 1.419246@0] IR LIRC bridge handler initialized
- [ 1.423939@0] usbcore: registered new interface driver uvcvideo
- [ 1.429742@0] USB Video Class driver (1.1.1)
- [ 1.434266@0] device-mapper: uevent: version 1.0.3
- [ 1.439040@0] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
- [ 1.447529@0] Bluetooth: HCI UART driver ver 2.2
- [ 1.451931@0] Bluetooth: HCI H4 protocol initialized
- [ 1.457197@0] hidraw: raw HID events driver (C) Jiri Kosina
- [ 1.467523@0] usbcore: registered new interface driver usbhid
- [ 1.468129@1] hdmitx: system: gate/pwr cmd: 5
- [ 1.468133@1] hdmitx: edid: edid ready
- [ 1.468138@1] hdmitx: edid: check sum valid
- [ 1.468140@1] hdmitx: edid: check sum valid
- [ 1.468142@1] hdmitx: edid: blk0 raw data
- [ 1.468164@1] 00ffffffffffff00410c00000101010104180103804024780af9aba2554a9a25
- [ 1.468184@1] 0f474a2108008180010101010101010101010101010104740030f2705a80b058
- [ 1.468204@1] 8a0080682100001e023a801871382d40582c450080682100001e000000fc0050
- [ 1.468223@1] 48494c495053204654560a20000000fd00184c1e531e000a2020202020200132
- [ 1.468224@1]
- [ 1.468225@1] hdmitx: edid: blk1 raw data
- [ 1.468245@1] 02033c714d1f102021140513041102150601290907031507503d07c083010000
- [ 1.468265@1] 7b030c002000003c20c86e020103014100fc20306070281038106810023a80d0
- [ 1.468284@1] 72382d40102c458080682100001e011d803e73382d407e2c458080682100001e
- [ 1.468303@1] 011d80d0721c1620102c258080682100009e000000000000000000000000005b
- [ 1.468304@1]
- [ 1.468340@1] hdmitx: edid: find IEEEOUT
- [ 1.468381@1] hdmitx: video: get current mode: 1080p
- [ 1.468389@1] is_similar_hdmi_vic[325] vic_old=16,mode_new=15
- [ 1.468391@1] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
- [ 1.468394@1] hdmitx: audio: audio channel num is 0
- [ 1.468399@1] hdmitx: audio: SPDIF
- [ 1.468411@1] hdmitx: audio: current VIC: 16
- [ 1.468412@1] hdmitx: audio: audio sample rate: 0
- [ 1.468414@1] hdmitx: audio: set audio N para
- [ 1.468421@1] hdmitx: audio: PCM out to HDMI
- [ 1.489000@1] hdmitx: audio: Time out: AIU_HDMI_CLK_DATA_CTRL
- [ 1.489002@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 1.489003@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 1.489058@1] hdmitx: cec: CEC not ready
- [ 1.619848@0] usbhid: USB HID core driver
- [ 1.624235@0] zram: Created 1 device(s) ...
- [ 1.628354@0] ashmem: initialized
- [ 1.631425@0] logger: created 256K log 'log_main'
- [ 1.636111@0] logger: created 256K log 'log_events'
- [ 1.640970@0] logger: created 256K log 'log_radio'
- [ 1.645730@0] logger: created 256K log 'log_system'
- [ 1.650727@0] vout_init_module
- [ 1.653502@0] start init vout module
- [ 1.657258@0] create vout attribute ok
- [ 1.661690@0] ge2d_init
- [ 1.663603@0] ge2d_dev major:243
- [ 1.667096@0] ge2d start monitor
- [ 1.670234@0] osd_init
- [ 1.670239@1] ge2d workqueue monitor start
- [ 1.676718@0] osd_probe, vinfo:c083630c
- [ 1.681019@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=73728K
- [ 1.688662@0] osd_probe, mydef_var:c0bfb0e0, vinfo:c083630c
- [ 1.694198@0] init fbdev bpp is :32
- [ 1.697754@0] ---------------clear framebuffer0 memory
- [ 1.751806@0] Console: switching to colour frame buffer device 240x67
- [ 1.778328@0] Frame buffer memory assigned at phy:0x0a900000, vir:0xf0200000, size=1024K
- [ 1.784130@0] osd_probe, mydef_var:c0bfb0e0, vinfo:c083630c
- [ 1.789686@0] don't find to display_size_default from mesonfb-dts
- [ 1.795748@0] init fbdev bpp is :16
- [ 1.811585@0] osd probe ok
- [ 1.811748@0] osd_ext_init
- [ 1.812124@0] vout2_init_module enter
- [ 1.821409@0] amlvideo-000: V4L2 device registered as video10
- [ 1.821710@0] amlvideo2: V4L2 device registered as video11
- [ 1.827272@0] ionvideo-000: V4L2 device registered as video13
- [ 1.832711@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
- [ 1.841528@0] aml_wdt_driver_init,301
- [ 1.844743@0] ** disable watchdog
- [ 1.848254@0] keys===========================================
- [ 1.853759@0] keys_devno=f000000
- [ 1.857150@0] securitykey: device aml_keys created
- [ 1.861770@0] amlkeys=0
- [ 1.864234@0] platform_driver_register--aml_keys_driver--------------------
- [ 1.871180@0] key unify config unifykey-num is 6
- [ 1.875712@0] key unify fact unifykey-num is 6
- [ 1.880140@0] aml_unifykeys_probe:694=============unifykey_devno:ef00000
- [ 1.886970@0] unifykey: device unifykeys created ok
- [ 1.891734@0] platform_driver_register--unifykey management driver--------------------
- [ 1.899891@0] set uart_ao pinmux use pinctrl subsystem
- [ 1.904727@0] P_AO_RTI_PIN_MUX_REG:5860
- [ 1.908585@0] start uart_ao_ttyS0:(irq = 122)
- [ 1.912879@0] register uart_ao ok
- [ 1.916375@0] set uart_a pinmux use pinctrl subsystem
- [ 1.921228@0] P_AO_RTI_PIN_MUX_REG:5860
- [ 1.925021@0] start uart_a_ttyS1:(irq = 58)
- [ 1.929196@0] register uart_a ok
- [ 1.932568@0] start uart_d_ttyS4:(irq = 126)
- [ 1.936626@0] register uart_d ok
- [ 1.939995@0] dwc_otg: version 3.10a 12-MAY-2014
- [ 1.944454@0] dwc_otg_driver_probe NOT match
- [ 1.948733@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
- [ 1.957265@0] USB (1) use clock source: XTAL input
- [ 1.983086@0] Core Release: 3.10a
- [ 1.983111@0] Setting default values for core params
- [ 1.985709@0] curmode: 1, host_only: 1
- [ 2.009581@0] Using Buffer DMA mode
- [ 2.009607@0] OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 2.011941@0] Working on port type = HOST
- [ 2.016630@0] dwc_otg lm1: DWC OTG Controller
- [ 2.020302@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
- [ 2.026950@0] dwc_otg lm1: irq 63, io mem 0x00000000
- [ 2.031900@0] -------hcd->flags.d32 = 0
- [ 2.035705@0] Init: Port Power? op_state=1
- [ 2.039783@0] Init1: Power Port (0)
- [ 2.043314@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.050191@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.057534@0] usb usb1: Product: DWC OTG Controller
- [ 2.062410@0] usb usb1: Manufacturer: Linux 3.10.86 dwc_otg_hcd
- [ 2.068300@0] usb usb1: SerialNumber: lm1
- [ 2.072652@0] hub 1-0:1.0: USB hub found
- [ 2.076177@0] hub 1-0:1.0: 1 port detected
- [ 2.080443@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
- [ 2.088858@0] USB (0) use clock source: XTAL input
- [ 2.114638@0] Core Release: 3.10a
- [ 2.114662@0] Setting default values for core params
- [ 2.117257@0] curmode: 1, host_only: 0
- [ 2.181091@0] Using Buffer DMA mode
- [ 2.181116@0] OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 2.183448@0] Working on port type = OTG
- [ 2.187348@0] Current port type: SLAVE
- [ 2.191209@0] dwc_otg lm0: DWC OTG Controller
- [ 2.195425@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
- [ 2.202121@0] dwc_otg lm0: irq 62, io mem 0x00000000
- [ 2.207056@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.213989@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.221348@0] usb usb2: Product: DWC OTG Controller
- [ 2.226183@0] usb usb2: Manufacturer: Linux 3.10.86 dwc_otg_hcd
- [ 2.232098@0] usb usb2: SerialNumber: lm0
- [ 2.236426@0] hub 2-0:1.0: USB hub found
- [ 2.239997@0] hub 2-0:1.0: 1 port detected
- [ 2.244155@0] Dedicated Tx FIFOs mode
- [ 2.247915@0] using timer detect id change, ecf4f800
- [ 2.252772@0] boot_device_flag : 0
- [ 2.256001@0] ===========================================amlnf_init:642,nand device tree ok,dev-name:nand
- [ 2.265543@0] Nand PHY driver Version: 2.01.001.0006 (c) 2013 Amlogic Inc.
- [ 2.271248@3] HOST mode
- [ 2.274833@0] amlnf_phy_init : amlnf init flag 0
- [ 2.279455@1] Indeed it is in host mode hprt0 = 00021501
- [ 2.279503@0] ######STS IRQ mode for nand driver
- [ 2.279554@0] NAND device id: ad de 94 da 74 c4 ad de
- [ 2.279559@0] detect NAND device: A revision 20nm NAND 8GiB H27UCG8T2A
- [ 2.297813@3] -------hcd->flags.d32 = 0
- [ 2.297838@3] Init: Port Power? op_state=1
- [ 2.297840@3] Init1: Power Port (0)
- [ 2.297844@3] [RN5T618]rn5t618_otg_change, driver is not ready, do it later
- [ 2.297846@3] set usb port power on (board gpio 15)!
- [ 2.324316@0] AML_NAND_NEW_OOB : new oob
- [ 2.327972@0] bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
- [ 2.335840@0] boot_device_flag = 0
- [ 2.340990@0] hynix nand get default reg value at blk:8, page:2048
- [ 2.346017@0] NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 0
- [ 2.357814@0] NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
- [ 2.362361@0] nand shipped bbt at block 6
- [ 2.382153@0] NAND CKECK : arg phyp: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 1
- [ 2.418238@0] NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 52
- [ 2.421362@0] i=0,register --- nand_key
- [ 2.424866@0] amlnand_phydev_init,1179,phydev->offset=6000000,phydev->size=24800000
- [ 2.432497@0] amlnand_phydev_init,1179,phydev->offset=2a800000,phydev->size=4f800000
- [ 2.440209@0] amlnand_phydev_init,1179,phydev->offset=7a000000,phydev->size=186000000
- [ 2.448009@0] nfcache : offset: 0x000006000000 -0x000024800000 : partitons 1 : single_chip multi_plane
- [ 2.457522@0] nfcode : offset: 0x00002a800000 -0x00004f800000 : partitons 6 : single_chip multi_plane
- [ 2.467080@0] nfdata : offset: 0x00007a000000 -0x000186000000 : partitons 1 : single_chip multi_plane
- [ 2.478504@0] bad block count = 0
- [ 2.478504@0]
- [ 2.485601@0] bad block count = 0
- [ 2.485601@0]
- [ 2.497808@1] usb 1-1: new high-speed USB device number 2 using dwc_otg
- [ 2.498999@3] Indeed it is in host mode hprt0 = 00001101
- [ 2.506597@0] bad block count = 0
- [ 2.506597@0]
- [ 2.509025@0] amlnand_add_nftl:
- [ 2.512130@0] Creating 1 ntd partitions
- [ 2.515942@0] block_num 146
- [ 2.520718@0] ------init_ntd
- [ 2.522028@0] ntd: Giving out device 0 to nfcache
- [ 2.526343@0] Creating 6 ntd partitions
- [ 2.530192@0] block_num 318
- [ 2.537384@0] ntd: Giving out device 1 to nfcode
- [ 2.537611@0] Creating 1 ntd partitions
- [ 2.541454@0] block_num 1560
- [ 2.564911@0] ntd: Giving out device 2 to nfdata
- [ 2.565436@0] boot_device_flag : 0
- [ 2.567266@0] register_ntd_blktrans start
- [ 2.571285@0] ntd device 250!
- [ 2.574201@0] ntd->name: nfcache
- [ 2.577410@0] adjust_block_num : 4,reserved_block_ratio 10
- [ 2.582920@0] nftl version 150204a
- [ 2.586250@0] nftl build Feb 4 2015_21:22:11
- [ 2.590616@0] nftl part attr 0
- [ 2.595497@0] nftl start:146,17
- [ 2.596899@0] first
- [ 2.678183@0] average_erase_count:0
- [ 2.678209@0] second 11,129
- [ 2.678809@0] part->max_discard_block = 4
- [ 2.689215@0] all block full!!
- [ 2.689236@0] all discard block full!!
- [ 2.690358@0] free block cnt = 135
- [ 2.693738@0] new current block is 139
- [ 2.697468@0] total discard page count is 0
- [ 2.701655@0] create_part_list:1238,current_used_discard_block=133,current_discard_block_used_count=16
- [ 2.709002@3] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
- [ 2.709007@3] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
- [ 2.709011@3] usb 1-1: Product: USB2.0 Hub
- [ 2.709598@3] hub 1-1:1.0: USB hub found
- [ 2.709876@3] hub 1-1:1.0: 4 ports detected
- [ 2.711446@3] Indeed it is in host mode hprt0 = 00021501
- [ 2.743038@0] unmappig_pages=31466,discarded_pages=0,mapping_pages=1558
- [ 2.749074@0] nftl ok!
- [ 2.751805@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 2.756373@0] aml_nftl_add_ntd ok
- [ 2.759294@0] ntd device 250!
- [ 2.762222@0] ntd->name: nfcode
- [ 2.765339@0] adjust_block_num : 4,reserved_block_ratio 10
- [ 2.770827@1] nftl version 150204a
- [ 2.774179@1] nftl build Feb 4 2015_21:22:11
- [ 2.778551@1] nftl part attr 0
- [ 2.785633@1] nftl start:318,33
- [ 2.785956@1] first
- [ 2.887813@3] usb 2-1: new full-speed USB device number 2 using dwc_otg
- [ 2.888928@3] Indeed it is in host mode hprt0 = 00021501
- [ 2.948719@1] average_erase_count:0
- [ 2.948750@1] second 291,285
- [ 2.949427@1] part->max_discard_block = 4
- [ 3.089877@3] usb 2-1: New USB device found, idVendor=046d, idProduct=c52b
- [ 3.091116@3] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- [ 3.098405@3] usb 2-1: Product: USB Receiver
- [ 3.102642@3] usb 2-1: Manufacturer: Logitech
- [ 3.113523@3] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-lm0-1/input2
- [ 3.122790@1] current_block1:25
- [ 3.127183@1] all discard block full!!
- [ 3.127314@1] free block cnt = 45
- [ 3.130285@1] new current block is 27
- [ 3.198118@3] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
- [ 3.276907@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
- [ 3.358140@3] usb 1-1.1: new high-speed USB device number 4 using dwc_otg
- [ 3.518058@3] usb 1-1.1: new high-speed USB device number 5 using dwc_otg
- [ 3.540157@3] usb 1-1.1: New USB device found, idVendor=05e3, idProduct=0718
- [ 3.541577@3] usb 1-1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=2
- [ 3.549038@3] usb 1-1.1: Product: USB Storage
- [ 3.553366@3] usb 1-1.1: SerialNumber: 000000000033
- [ 3.558952@3] usb-storage 1-1.1:1.0: USB Mass Storage device detected
- [ 3.564860@3] scsi0 : usb-storage 1-1.1:1.0
- [ 3.767685@0] recover_current_block_mapping : fill the current block, from page 255
- [ 3.769717@0] total discard page count is 0
- [ 3.773858@0] create_part_list:1238,current_used_discard_block=26,current_discard_block_used_count=330
- [ 3.784378@0] unmappig_pages=7710,discarded_pages=0,mapping_pages=65250
- [ 3.789752@0] nftl ok!
- [ 3.792596@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.797120@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.801691@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.806261@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.810887@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.815463@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.820009@0] aml_nftl_add_ntd ok
- [ 3.822919@0] ntd device 250!
- [ 3.825865@0] ntd->name: nfdata
- [ 3.829019@0] adjust_block_num : 4,reserved_block_ratio 10
- [ 3.834449@0] nftl version 150204a
- [ 3.837869@0] nftl build Feb 4 2015_21:22:11
- [ 3.842285@0] nftl part attr 0
- [ 3.865211@0] nftl start:1560,146
- [ 3.866520@0] first
- [ 4.687421@0] found discard block:1524
- [ 4.705168@0] average_erase_count:0
- [ 4.705220@0] second 321,1414
- [ 4.705964@0] part->max_discard_block = 4
- [ 4.896506@0] current_block1:1238
- [ 4.901567@0] currnet_discard_block1:1524
- [ 4.903398@0] reach the last discard page:2
- [ 4.905099@0] free block cnt = 1264
- [ 4.907564@0] new current block is 1239
- [ 5.054486@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
- [ 5.543424@0] recover_current_block_mapping : fill the current block, from page 255
- [ 5.545437@0] total discard page count is 2
- [ 5.549619@0] create_part_list:1238,current_used_discard_block=1524,current_discard_block_used_count=36
- [ 5.565816@0] unmappig_pages=322324,discarded_pages=1849,mapping_pages=37811
- [ 5.567221@0] nftl ok!
- [ 5.570196@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 5.574594@0] aml_nftl_add_ntd ok
- [ 5.577459@0] init_aml_nftl end
- [ 5.580735@0] ethernet_driver probe!
- [ 5.584128@0] Please config phy interface.
- [ 5.588315@0] Please config savepowermode.
- [ 5.592359@0] Please config reset_pin_enable.
- [ 5.596696@0] Please config reset_delay.
- [ 5.600614@0] Please config reset_pin.
- [ 5.604323@0] ethernetinit(dbg[c0c01b84]=1)
- [ 5.608520@0] ethernet base addr is fe0c0000
- [ 5.612733@0] write mac add to:ed85a3c8: 00 01 db 88 06 e4 |......|
- [ 5.621570@0] libphy: AMLMAC MII Bus: probed
- [ 5.623220@0] eth0: PHY ID 02430c54 at 0 IRQ -1 (0:00) active
- [ 5.630916@3] Amlogic A/V streaming port init
- [ 5.634778@3] buffersize=262144,0,start=0
- [ 5.637280@3] Subtitle stbuf alloced at 0xecc40000, size = 262144
- [ 5.643363@3] changed the (2) buffer size from 0 to 262144
- [ 5.649082@3] init vdec memsource ca00000->1c9fffff
- [ 5.653846@3] [tsync_pcr_init]init success.
- [ 5.657920@3] amvideocap_init_module
- [ 5.661690@3] regist mpeg12 codec profile
- [ 5.665544@3] regist mpeg4 codec profile
- [ 5.669356@3] amvdec_vc1 module init
- [ 5.672994@3] regist vc1 codec profile
- [ 5.676630@3] amvdec_h264 module init
- [ 5.680390@3] regist h264 codec profile
- [ 5.684084@3] amvdec_h264mvc module init
- [ 5.688089@3] regist hmvc codec profile
- [ 5.691798@3] amvdec_h264_4k2k module init
- [ 5.695962@3] regist h264_4k2k codec profile
- [ 5.700129@3] amvdec_h265 module init
- [ 5.703852@3] regist hevc_unsupport codec profile
- [ 5.708540@3] regist mjpeg codec profile
- [ 5.712342@3] amvdec_real module init
- [ 5.716068@3] amvdec_avs module init
- [ 5.719771@3] amvenc_avc memory resource undefined.
- [ 5.724392@3] encode_wq_init.
- [ 5.727342@3] encode start monitor.
- [ 5.730869@2] encode workqueue monitor start.
- [ 5.731193@3] jpegenc module init
- [ 5.731488@3] alloc_keep_buffer keep_y_addr ec600000
- [ 5.731500@3] alloc_keep_buffer keep_u_addr ecd00000
- [ 5.731507@3] alloc_keep_buffer keep_v_addr ec200000
- [ 5.731510@3] yaddr=ec600000,u_addr=ecd00000,v_addr=ec200000
- [ 5.731812@3] create_ge2d_work_queue video task ok
- [ 5.731815@3] video2_init enter
- [ 5.732295@3]
- [ 5.732295@3]
- [ 5.732295@3] VECM init
- [ 5.732295@3]
- [ 5.732542@3] efuse===========================================
- [ 5.732733@3] efuse: device efuse created
- [ 5.732825@3] efuse--------------------------------------------
- [ 5.732827@3] SARADC Driver init.
- [ 5.732971@3] __saradc_probe__
- [ 5.877919@3] saradc calibration: ref_val = 509
- [ 5.877949@3] saradc calibration: ref_nominal = 512
- [ 5.881674@3] saradc calibration: coef = 4080
- [ 5.886111@3] Remote Driver
- [ 5.888871@3] Remote platform_data g_remote_base=fe600580
- [ 5.894189@3] set drvdata completed
- [ 5.897715@3] device_create_file completed
- [ 5.902292@3] input: aml_keypad as /devices/platform/meson-remote/input/input0
- [ 5.909456@3] input_register_device completed
- [ 5.913708@3] [0xffffff00] = 0x1dd0190
- [ 5.917391@3] [0xffffff04] = 0xf800ca
- [ 5.921038@3] [0xffffff08] = 0x82006e
- [ 5.924671@3] [0xffffff0c] = 0x3c0030
- [ 5.928316@3] [0xffffff10] = 0x30fa0013
- [ 5.932124@3] [0xffffff18] = 0x6f19000
- [ 5.935851@3] [0xffffff1c] = 0xbe40
- [ 5.939327@3] [0x0] = 0xfa00a0
- [ 5.942353@3] [0x4] = 0xfa00a0
- [ 5.945386@3] [0x8] = 0xfa00a0
- [ 5.948427@3] [0xc] = 0x640030
- [ 5.951454@3] [0x10] = 0x30fa0013
- [ 5.954748@3] [0x18] = 0x961b800
- [ 5.957961@3] [0x1c] = 0x9740
- [ 5.960902@3] [0x20] = 0x104
- [ 5.963763@3] [0x24] = 0x0
- [ 5.966450@3] [0x28] = 0x0
- [ 5.969144@3] set_remote_mode[69]
- [ 5.972446@3] remote config major:234
- [ 5.976370@3] physical address:0x2da5e000
- [ 5.980261@3] GPIO Keypad Driver init.
- [ 5.983943@3] ==gpio_key_probe==
- [ 5.987106@3] reg:2620,clearmask=400040,setmask=1
- [ 5.991838@3] reg:2622,clearmask=ff0000,set pin=3
- [ 5.996518@3] reg:2623,clearmask=7000000,setmask=7
- [ 6.001309@3] reg:2620,clearmask=800080,setmask=10001
- [ 6.006399@3] reg:2622,clearmask=ff000000,set pin=3
- [ 6.011254@3] reg:2623,clearmask=70000000,setmask=7
- [ 6.016194@3] power key(116) registed.
- [ 6.019947@3] scsi 0:0:0:0: Direct-Access USB TO I DE/SATA Device 0016 PQ: 0 ANSI: 4
- [ 6.028285@1] input: gpio_keypad as /devices/platform/gpio_keypad.6/input/input1
- [ 6.031196@3] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
- [ 6.032195@3] sd 0:0:0:0: [sda] Asking for cache data failed
- [ 6.032199@3] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 6.053857@1] gpio keypad register input device completed.
- [ 6.057312@3] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
- [ 6.058315@3] sd 0:0:0:0: [sda] Asking for cache data failed
- [ 6.058318@3] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 6.058324@3] sd 0:0:0:0: [sda] Attached SCSI disk
- [ 6.082179@1] gpio keypad major:233
- [ 6.085999@1] VFD Driver################################
- [ 6.091057@1] ###################vfd_probe
- [ 6.095161@1] VFD init ---CONFIG_VFD_TM1628####vfd_stb_gpio is 32
- [ 6.101239@1] ####vfd_clk_gpio is 35
- [ 6.104787@1] ####vfd_stb_gpio is 34
- [ 6.108350@1] ####################come here #####################
- [ 6.129832@1] up vfd key(103) registed.
- [ 6.129858@1] down vfd key(108) registed.
- [ 6.132015@1] right vfd key(106) registed.
- [ 6.136089@1] back vfd key(158) registed.
- [ 6.140085@1] left vfd key(105) registed.
- [ 6.144064@1] ok vfd key(232) registed.
- [ 6.148055@1] input: vfd_keypad as /devices/platform/m1-vfd.0/input/input2
- [ 6.154857@1] vfd config major:232
- [ 6.158497@1] spi_nor_init
- [ 6.160995@1] amlogic_spi_nor_probe:
- [ 6.164438@1] amlogic_spi->state_name:default
- [ 6.168911@1] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
- [ 6.176417@1] check_storage_device : spi boot_device_flag : 0
- [ 6.182040@1] spi_nor_probe
- [ 6.184833@1] spi_nor apollospi:32766: mx25l160 (2048 Kbytes)
- [ 6.190639@1] Creating 2 MTD partitions on "apollospi:32766":
- [ 6.196250@1] 0x000000000000-0x000000100000 : "bootloader"
- [ 6.202445@1] 0x000000100000-0x000000110000 : "ubootenv"
- [ 6.207657@1] amlogic_spi_nor_probe over
- [ 6.211064@1] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
- [ 6.220802@1] host->base fe108c20
- [ 6.223661@1] pdata->caps 7
- [ 6.226413@1] pdata->caps2 0
- [ 6.229287@1] get property: port, value:0x00000001
- [ 6.235774@1] get property: ocr_avail, value:0x00200000
- [ 6.242298@1] get property: f_min, value:0x000493e0
- [ 6.248783@1] get property: f_max, value:0x02faf080
- [ 6.255278@1] get property: max_req_size, value:0x00020000
- [ 6.261791@1] get property: irq_in, value:0x00000003
- [ 6.268288@1] get property: irq_out, value:0x00000005
- [ 6.274785@1] get property: gpio_cd, str:CARD_6
- [ 6.280770@1] get property: pinname, str:sd
- [ 6.286398@1] get property: jtag_pin, str:CARD_0
- [ 6.292389@1] get property: card_type, value:0x00000005
- [ ¦Å]
- [ 6.497827@1]
- [ 6.497827@1]
- [ 6.497827@1]
- [ 6.507092@1] [0;40;32m JTAG in[0m
- [ 6.547827@1] reg:2620,clearmask=80008,setmask=10001
- [ 6.547865@1] reg:2621,clearmask=ff000000,set pin=64
- [ 6.552177@1] reg:2623,clearmask=7000,setmask=7
- [ 6.556685@1] reg:2620,clearmask=200020,setmask=1
- [ 6.561452@1] reg:2622,clearmask=ff00,set pin=64
- [ 6.566046@1] reg:2623,clearmask=700000,setmask=7
- [ 6.570875@1] pdata->caps 80000507
- [ 6.574108@1] pdata->caps2 0
- [ 6.576969@1] get property: port, value:0x00000002
- [ 6.583479@1] get property: ocr_avail, value:0x00200000
- [ 6.589977@1] get property: f_min, value:0x000493e0
- [ 6.596472@1] get property: f_max, value:0x02faf080
- [ 6.602980@1] get property: f_max_w, value:0x02faf080
- [ 6.609481@1] get property: max_req_size, value:0x00020000
- [ 6.615980@1] get property: pinname, str:emmc
- [ 6.621790@1] get property: card_type, value:0x00000001
- [ 6.628293@1] get property: gpio_dat3, str:BOOT_3
- [ 6.634266@1] [is_emmc_exist] host->storage_flag=4, POR_BOOT_VALUE=5
- [ 6.640599@1] [aml_sdio_probe]: there is not eMMC/tsd, skip sdio_c dts config!
- [ 6.647807@1] pdata->caps 107
- [ 6.650734@1] pdata->caps2 0
- [ 6.653596@1] get property: port, value:0x00000000
- [ 6.660102@1] get property: ocr_avail, value:0x00200000
- [ 6.666598@1] get property: f_min, value:0x000493e0
- [ 6.673104@1] get property: f_max, value:0x02faf080
- [ 6.679616@1] get property: max_req_size, value:0x00020000
- [ 6.686105@1] get property: pinname, str:sdio
- [ 6.691916@1] get property: card_type, value:0x00000003
- [ 6.737826@1] [aml_sdio_probe] aml_sdio_probe() success!
- [ 6.738121@1] [dsp]DSP start addr 0xc5e00000
- [ 6.741762@1] [dsp]register dsp to char divece(257)
- [ 6.747012@1] amlogic audio spdif interface device init!
- [ 6.751964@1] name=nand_key nand_key
- [ 6.755801@1] register_aes_algorithm:488,new way
- [ 6.760408@1] key name:keyexample, key data:1234567890
- [ 6.765785@1] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
- [ 6.773104@1] input: rn5t618_pmu as /devices/i2c-0/0-0032/rn5t618_pmu.0/input/input3
- [ 6.779086@1] [RN5T618] NO BATTERY_PARAMETERS FOUND
- [ 6.783785@1] [RN5T618]rn5t618_otg_change, value:1, is_short:0
- [ 6.790712@1] register 0xB3:33
- [ 6.795662@1] ------------[ cut here ]------------
- [ 6.797403@1] WARNING: at kernel/workqueue.c:1368 __queue_work+0x248/0x368()
- [ 6.804413@1] Modules linked in:
- [ 6.807624@1] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.10.86 #1
- [ 6.813791@1] [<c0014d84>] (unwind_backtrace+0x0/0xec) from [<c0011dac>] (show_stack+0x10/0x14)
- [ 6.822450@1] [<c0011dac>] (show_stack+0x10/0x14) from [<c00321d8>] (warn_slowpath_common+0x54/0x6c)
- [ 6.831551@1] [<c00321d8>] (warn_slowpath_common+0x54/0x6c) from [<c003228c>] (warn_slowpath_null+0x1c/0x24)
- [ 6.841346@1] [<c003228c>] (warn_slowpath_null+0x1c/0x24) from [<c004c0d8>] (__queue_work+0x248/0x368)
- [ 6.850622@1] [<c004c0d8>] (__queue_work+0x248/0x368) from [<c004c238>] (queue_work_on+0x40/0x4c)
- [ 6.859468@1] [<c004c238>] (queue_work_on+0x40/0x4c) from [<c05485f8>] (rn5t618_otg_change+0x184/0x1ac)
- [ 6.868826@1] [<c05485f8>] (rn5t618_otg_change+0x184/0x1ac) from [<c05488cc>] (rn5t618_battery_probe+0x2ac/0x5b0)
- [ 6.879055@1] [<c05488cc>] (rn5t618_battery_probe+0x2ac/0x5b0) from [<c0314414>] (driver_probe_device+0xd4/0x21c)
- [ 6.889282@1] [<c0314414>] (driver_probe_device+0xd4/0x21c) from [<c0314608>] (__driver_attach+0x68/0x8c)
- [ 6.898819@1] [<c0314608>] (__driver_attach+0x68/0x8c) from [<c03128bc>] (bus_for_each_dev+0x4c/0xa4)
- [ 6.908005@1] [<c03128bc>] (bus_for_each_dev+0x4c/0xa4) from [<c0313afc>] (bus_add_driver+0xd0/0x25c)
- [ 6.917191@1] [<c0313afc>] (bus_add_driver+0xd0/0x25c) from [<c0314c24>] (driver_register+0xa8/0x140)
- [ 6.926381@1] [<c0314c24>] (driver_register+0xa8/0x140) from [<c0547184>] (rn5t618_battery_init+0x10/0x34)
- [ 6.936003@1] [<c0547184>] (rn5t618_battery_init+0x10/0x34) from [<c0008544>] (do_one_initcall+0xa0/0x148)
- [ 6.945629@1] [<c0008544>] (do_one_initcall+0xa0/0x148) from [<c0b44bdc>] (kernel_init_freeable+0x130/0x218)
- [ 6.955424@1] [<c0b44bdc>] (kernel_init_freeable+0x130/0x218) from [<c07d29b4>] (kernel_init+0x8/0x160)
- [ 6.964784@1] [<c07d29b4>] (kernel_init+0x8/0x160) from [<c000e0a0>] (ret_from_fork+0x14/0x34)
- [ 6.973368@1] ---[ end trace 942637d0dc47b84a ]---
- [ 7.084490@1] vdin_drv_init: major 230
- [ 7.084760@1] vdin1 mem_start = 0x1ca00000, mem_size = 0x1000000
- [ 7.088610@1] vdin_drv_probe: driver initialized ok
- [ 7.093566@1] amvdec_656in module: init.
- [ 7.097336@1] amvdec_656in_init_module:major 229
- [ 7.102342@1] amvdec_656in probe ok.
- [ 7.105902@1] amvdec_csi probe ok.
- [ 7.108946@1] [viuin..]viuin_init_module viuin module init
- [ 7.114553@1] [viuin..]viuin_probe probe ok.
- [ 7.118993@1] [isp..]isp_probe isp probe ok.
- [ 7.122887@1] [sii9233a_drv_init] Ver: 2013Nov12
- [ 7.128605@1] amaudio2: device amaudio2 created
- [ 7.132085@1] Error: Didn't get power valid value --- wifi_power_probe 323
- [ 7.138781@1] wifi_power power_gpio is 6
- [ 7.142671@1] wifi_power power_gpio2 is 123
- [ 7.147153@1] amlogic rfkill init
- [ 7.150178@1] not get gpio_en
- [ 7.153070@1] not get gpio_wake
- [ 7.177930@1] wifi_request_32k_clk : OFF-->ON for bt_rfkill
- [ 7.177966@1] clock_32k_pin(122) : (null)
- [ 7.181853@1] clock_32k_pin(122) : sdio_wifi
- [ 7.349648@1] UMP: UMP device driver 0000 loaded
- [ 7.350030@1] aml_hw_crypto initialization.
- [ 7.353389@1] usbcore: registered new interface driver snd-usb-audio
- [ 7.359588@1] enter rt5616_modinit
- [ 7.362696@1] dummy_codec_platform_probe
- [ 7.366607@1] == ES8323 == es8323_modinit()
- [ 7.371210@1] i2s get no clk src setting in dts, use the default mpll 0
- [ 7.377232@1] [aml-i2s-dai]enterd aml_i2s_dai_probe,old_samplerate:0,sample_rate=48000
- [ 7.385389@1] [aml-spdif-dai]enter aml_dai_spdif_init
- [ 7.390242@1] [aml-spdif-dai]enterd aml_spdif_play,set_clock:-1,sample_rate=4
- [ 7.397338@1] audio_set_958_clk, freq=4,
- [ 7.401252@1] IEC958 16bit
- [ 7.403928@1] hdmitx: audio: aout notify rate 48000
- [ 7.408788@1] hdmitx: audio: aout notify size 16
- [ 7.413375@1] hdmitx: audio: aout notify format CT_PCM
- [ 7.418510@1] hdmitx: audio: audio channel num is 1
- [ 7.423346@1] hdmitx: audio: SPDIF
- [ 7.426731@1] hdmitx: audio: current VIC: 16
- [ 7.430979@1] hdmitx: audio: audio sample rate: 3
- [ 7.435652@1] hdmitx: audio: set audio N para
- [ 7.439997@1] hdmitx: audio: PCM out to HDMI
- [ 7.444234@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 7.448919@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 7.454118@1] hdmitx: audio: Audio Type: PCM
- [ 7.458410@1] hdmitx: audio: set audio param
- [ 7.462668@1] [aml-spdif-dai]aml_spdif_probe
- [ 7.467107@1] test codec dummy_codec
- [ 7.470510@1] using external codec, index = 1
- [ 7.474832@1] using external dummy codec
- [ 7.478884@1] enter spdif_dit_probe
- [ 7.482286@1] aml_spdif_unmute
- [ 7.485613@1] codec_name = dummy_codec.0
- [ 7.489579@1] p_aml_audio->hp_disable=1
- [ 7.493123@1] falied to get spk event delay time paraments from dts file
- [ 7.499807@1] spk_event delay_time = 0
- [ 7.504611@1] aml-i2s 0:playback preallocate_dma_buffer: area=ef300000, addr=2f500000, size=524288
- [ 7.512794@1] aml-i2s 1:capture preallocate_dma_buffer: area=ef240000, addr=2f440000, size=65536
- [ 7.521235@1] aml_snd_m8 aml_m8_sound_card.5: dummy_codec <-> aml-i2s-dai.0 mapping ok
- [ 7.530448@1] aml-i2s 0:playback preallocate_dma_buffer: area=ef400000, addr=2f600000, size=524288
- [ 7.538444@1] aml-i2s 1:capture preallocate_dma_buffer: area=ef260000, addr=2f460000, size=65536
- [ 7.546880@1] aml_snd_m8 aml_m8_sound_card.5: dit-hifi <-> aml-spdif-dai.0 mapping ok
- [ 7.555775@1] -----ext_codec=1---
- [ 7.558072@1] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
- [ 7.564197@1] Netfilter messages via NETLINK v0.30.
- [ 7.568932@1] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
- [ 7.575607@1] ctnetlink v0.93: registering with nfnetlink.
- [ 7.580649@1] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
- [ 7.587693@1] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
- [ 7.594191@1] xt_time: kernel timezone is -0000
- [ 7.598268@1] ipip: IPv4 over IPv4 tunneling driver
- [ 7.603559@1] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 7.608619@1] arp_tables: (C) 2002 David S. Miller
- [ 7.613293@1] TCP: cubic registered
- [ 7.616731@1] Initializing XFRM netlink socket
- [ 7.621683@1] NET: Registered protocol family 10
- [ 7.626290@1] mip6: Mobile IPv6
- [ 7.628903@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 7.634556@1] sit: IPv6 over IPv4 tunneling driver
- [ 7.640143@1] NET: Registered protocol family 17
- [ 7.643796@1] NET: Registered protocol family 15
- [ 7.648435@1] Bridge firewalling registered
- [ 7.652600@1] Bluetooth: RFCOMM TTY layer initialized
- [ 7.657573@1] Bluetooth: RFCOMM socket layer initialized
- [ 7.662963@1] Bluetooth: RFCOMM ver 1.11
- [ 7.666748@1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- [ 7.672216@1] Bluetooth: BNEP filters: protocol multicast
- [ 7.677590@1] Bluetooth: BNEP socket layer initialized
- [ 7.682731@1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- [ 7.688776@1] Bluetooth: HIDP socket layer initialized
- [ 7.693918@1] l2tp_core: L2TP core driver, V2.0
- [ 7.698401@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
- [ 7.703327@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
- [ 7.709077@1] l2tp_netlink: L2TP netlink interface
- [ 7.713832@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
- [ 7.719903@1] l2tp_debugfs: L2TP debugfs support
- [ 7.724477@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
- [ 7.731099@1] NET: Registered protocol family 35
- [ 7.735722@1] Key type dns_resolver registered
- [ 7.740994@1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- [ 7.747930@1] Registering SWP/SWPB emulation handler
- [ 7.752824@1] enter meson_pm_init
- [ 7.756237@1] enter meson_pm_probe!
- [ 7.759598@1] meson_pm_probe done !
- [ 7.763603@1] regulator-dummy: disabling
- [ 7.767429@1] aml_rtc rtc.0: setting system clock to 2001-11-01 19:11:06 UTC (1004641866)
- [ 7.775133@1] ### dt-test ### No testcase data in device tree; not running tests
- [ 7.782562@1] meson_cpufreq: no voltage_control prop
- [ 7.787409@1] voltage_control = 0
- [ 7.791926@1] hdmitx: cec: CEC init
- [ 7.794201@0] hdmitx: cec: CEC task process
- [ 7.798392@1] input: cec_input as /devices/virtual/input/input4
- [ 7.804326@1] hdmitx: cec: hdmitx_device->cec_init_ready:0x1
- [ 7.82[ 7.827794@1] Changing uart_ao_ttyS0: baud from 0 to 115200
- [ 7.847951@1] Freeing unused kernel memory: 356K (c0b44000 - c0b9d000)
- e2fsck 1.42.12 (29-Aug-2014)
- [ 7.868972@2] aml_nftl_open ok!
- [ 7.869035@2] aml_nftl_open ok!
- Pass 1: Checking inodes, blocks, and sizes
- Pass 2: Checking directory structure
- Pass 3: Checking directory connectivity
- Pass 4: Checking reference counts
- Pass 5: Checking group summary information
- /dev/system: 1956/65536 files (1.5% non-contiguous), 252449/262144 blocks
- e2fsck 1.42.12 (29-Aug-2014)
- [ 8.022238@2] aml_nftl_open ok!
- [ 8.023170@2] aml_nftl_open ok!
- /dev/data: recovering journal
- [ 8.038810@1] aml_nftl_open ok!
- [ 8.044771@1] aml_nftl_open ok!
- Pass 1: Checking inodes, blocks, and sizes
- Pass 2: Checking directory structure
- Pass 3: Checking directory connectivity
- Pass 4: Checking reference counts
- Pass 5: Checking group summary information
- /dev/data: 936/362160 files (8.8% non-contiguous), 151729/1447936 blocks
- [ 8.391409@0] tvmode set to 720p
- [ 8.391409@0]
- [ 8.391739@0] mode is 11,sync_duration_den=1,sync_duration_num=60
- [ 8.397848@0] TV mode 720p selected.
- [ 8.401354@0] tvoutc_setmode[489]
- [ 8.404646@0] new mode 720p
- [ 8.404646@0] set ok
- [ 8.409692@0] hdmitx: video: get current mode: 720p
- [ 8.414529@0] is_similar_hdmi_vic[325] vic_old=16,mode_new=11
- [ 8.420264@0] hdmitx: video: get current mode: 720p
- [ 8.425106@0] is_similar_hdmi_vic[325] vic_old=16,mode_new=11
- [ 8.430838@0] hdmitx: system: gate/pwr cmd: 7
- [ 8.435199@0] hdmitx: system: already init VIC = 0 Now VIC = 4
- [ 8.441079@0] hdmitx: system: 4 (cd0,cs0,pm1,vd0,1)
- [ 8.446079@0] hdmitx: system: gate/pwr cmd: 0
- [ 8.450435@0] hdmitx: system: hw reset
- [ 8.455181@0] hdmitx: audio: SPDIF
- [ 8.457573@0] hdmitx: system: reconfig packet setting done
- [ 8.597799@0] hdmitx: system: phy setting done
- [ 8.617811@0] hdmitx: system: set pll
- [ 8.617831@0] hdmitx: system: param->VIC:4
- [ 8.619908@0] mode is: 11
- [ 8.622506@0] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 8.626579@0] viu chan = 1
- [ 8.629283@0] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 8.633341@0] config HPLL
- [ 8.635942@0] set_hpll_clk_out[62] clk = 2970
- [ 8.657800@0] config HPLL done
- [ 8.657822@0] enc_vpu_bridge_reset[292]
- [ 8.797791@1] hdmitx: system: phy setting done
- [ 8.797815@1] Sink is HDMI device
- [ 8.799888@1] No sink attached
- [ 8.802954@1] hdmitx: audio: audio channel num is 1
- [ 8.807776@1] hdmitx: audio: SPDIF
- [ 8.811168@1] hdmitx: audio: current VIC: 4
- [ 8.815315@1] hdmitx: audio: audio sample rate: 3
- [ 8.820000@1] hdmitx: audio: set audio N para
- [ 8.824334@1] hdmitx: audio: PCM out to HDMI
- [ 8.828582@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 8.833259@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 8.838466@1] hdmitx: audio: Audio Type: PCM
- [ 8.843374@1] set_vout_mode[249]
- [ 8.925506@1] vfm_map_store:rm default
- [ 8.925506@1]
- [ 8.925583@1] vfm_map_store:add default decoder ppmgr deinterlace amvideo
- [ 8.925583@1]
- [H[J[H[J[ 8.943007@0] aml_nftl_open ok!
- [ 8.943206@0] blktrans_ioctl -cmd: 5331,801c0204,64
- [ 8.971609@0] aml_nftl_open ok!
- [ 8.971805@0] blktrans_ioctl -cmd: 5331,801c0204,64
- [ 8.973829@2] aml_nftl_open ok!
- [ 8.973867@2] aml_nftl_open ok!
- [ 9.007597@2] aml_nftl_open ok!
- [ 9.007655@2] aml_nftl_open ok!
- [ 9.023210@0] aml_nftl_open ok!
- [ 9.023938@0] EXT3-fs (system): error: couldn't mount because of unsupported optional features (40)
- [ 9.029858@0] aml_nftl_open ok!
- [ 9.032919@0] EXT2-fs (system): error: couldn't mount because of unsupported optional features (40)
- [ 9.041931@0] aml_nftl_open ok!
- [ 9.045052@0] force enable DISCARD here for ext4 fs
- [ 9.051542@0] checked enable EXT4 DISCARD here
- [ 9.054263@0] EXT4-fs (system): mounted filesystem with ordered data mode. Opts: (null)
- [ 9.150028@0] aml_nftl_open ok!
- [ 9.150774@0] EXT3-fs (data): error: couldn't mount because of unsupported optional features (40)
- [ 9.156445@0] aml_nftl_open ok!
- [ 9.159592@0] EXT2-fs (data): error: couldn't mount because of unsupported optional features (40)
- [ 9.168418@0] aml_nftl_open ok!
- [ 9.171516@0] force enable DISCARD here for ext4 fs
- [ 9.178742@0] checked enable EXT4 DISCARD here
- [ 9.180734@0] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: (null)
- [ 13.586566@0] systemd[1]: systemd 217 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK -SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN )
- [ 13.599341@0] systemd[1]: Detected architecture 'arm'.
- [ 13.60´
- Welcome to [1mOpenELEC (unofficial) - Version: devel-20150926153716-r20783-g553f562[0m!
- [ 13.635316@1] systemd[1]: Failed to insert module 'autofs4'
- [ 13.635755@1] systemd[1]: Set hostname to <OpenELEC>.
- [ 13.640405@1] systemd[1]: Initializing machine ID from random generator.
- [ 13.649314@1] systemd[1]: Populated /etc with preset unit settings.
- [ `[[32m OK [0m] Created slice Root Slice.
- [ 13.707851@1] systemd[1]: Created slice Roo[[32m OK [0m] Created slice System Slice.
- [ 13.727861@1] systemd[1]: Created slice System Starting Factory reset...
- [[32m OK [0m] Started Factory reset.
- [ 13.767848@1] systemd[1]: Started Factory reset[32m OK [0m] Reached target Factory reset target.
- [ 13.787849@0] systemd[1]: Reached target Factory reset target.
- [ 13.788131@0] systemd[1]: Start[ 13.862185@0] systemd[1]: Starting Kodi reboot script...
- [ 13.863106@0] systemd[1]: Unmounting /storage...
- [ 13.867935@0] systemd[1]: Unmounting /flash...
- Sta[ 13.872658@0] systemd[1]: Stopping Factory reset target.
- r[ 13.877375@0] systemd[1]: Stopped target Factory reset target.
- [ 13.883310@0] systemd[1]: Starting Shutdown.
- [ 13.887457@0] systemd[1]: Reached target Shutdown.
- [ 13.892284@2] aml_nftl_open ok!
- [ 13.893679@0] systemd[1]: Started Kodi reboot script.
- [ 13.900314@2] blktrans_ioctl -cmd: 4c01,801c0204,64
- [ 13.905941@0] systemd[1]: Unmounted /storage.
- ting Kodi reboot script...
- Unmounting /storage...
- Unmounting /flash...
- [[3[ 13.920002@1] aml_nftl_open ok!
- [ 13.920986@1] blktrans_ioctl -cmd: 4c01,801c0204,64
- [ 13.926660@0] systemd[1]: Unmounted /flash.
- 2m OK [0m] Stopped target Fac[ 13.933709@0] systemd[1]: Starting Unmount All Filesystems.
- [ 13.938474@0] systemd[1]: Reached target Unmount All Filesystems.
- [ 13.944566@0] systemd[1]: Starting Final Step.
- [ 13.948937@0] systemd[1]: Reached target Final Step.
- [ 13.953884@0] systemd[1]: Starting Reboot...
- tory reset target.
- [[32m OK [0m] Reached target Shutdown.
- [ 13.965986@0] systemd[1]: Shutting down.
- [ 13.986431@1] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
- [ 13.996991@1] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
- [ 14.006365@1] systemd-shutdown[1]: Unmounting file systems.
- [ 14.007045@1] systemd-shutdown[1]: All filesystems unmounted.
- [ 14.012035@1] systemd-shutdown[1]: Deactivating swaps.
- [ 14.017216@1] systemd-shutdown[1]: All swaps deactivated.
- [ 14.022521@1] systemd-shutdown[1]: Detaching loop devices.
- [ 14.028876@1] systemd-shutdown[1]: Not all loop devices detached, 1 left.
- [ 14.034732@1] systemd-shutdown[1]: Detaching DM devices.
- [ 14.040198@1] systemd-shutdown[1]: All DM devices detached.
- [ 14.045569@1] systemd-shutdown[1]: Cannot finalize remaining loop devices, continuing.
- [ 14.053916@1] systemd-shutdown[1]: Failed to finalize loop devices, ignoring
- [ 14.060866@1] systemd-shutdown[1]: Rebooting.
- [ 14.064896@1] aml_keys_notify_reboot:1717
- [ 14.091499@0] sd 0:0:0:0: Driver sd calling sd_shutdown shutdown
- [ 14.092261@0] rn5t618_pmu rn5t618_pmu.0: Driver rn5t618_pmu calling platform_drv_shutdown shutdown
- [ 14.101011@0] ricoh_pmu 0-0032: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.108011@0] i2c i2c-3: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.114406@0] i2c i2c-2: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.120829@0] i2c i2c-1: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.127233@0] i2c i2c-0: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.133710@0] amlnfdev nand: Driver amlnfdev calling platform_drv_shutdown shutdown
- [ 14.141285@0] boot_device_flag : 0
- [ 14.144709@0] aml_rtc rtc.0: Driver aml_rtc calling platform_drv_shutdown shutdown
- [ 14.152840@0] Restarting system.
- [ 14.155398@0]
- [ 14.157044@0] Restarting Linux version 3.10.86 (user@Debian) (gcc version 4.9.2 (GCC) ) #1 SMP PREEMPT Fri Sep 25 21:24:05 MSK 2015
- [ 14.157044@0]
- [ j
- TE : 33256
- BT : 19:49:35 Jul 29 2015
- PMU:rn5t618
- DC01 v:1100, 0x[36]: 28 -> 28
- DC02 v:1150, 0x[37]: 2c -> 2c
- DC03 v:1500, 0x[38]: 48 -> 48
- LDO01 v:2900, 0x[4c]: 50 -> 50
- LDO02 v:1800, 0x[4d]: 24 -> 24
- LDO03 v:1800, 0x[4e]: 30 -> 30
- LDO04 v:2850, 0x[4f]: 4e -> 4e
- LDO05 v:1800, 0x[50]: 24 -> 24
- LDO0a v:2700, 0x[56]: 28 -> 28
- LDO0b v:900, 0x[57]: 00 -> 00
- CPU clock is 1200MHz
- CPU type: M8
- DDR info: 2GB(auto) @ 792MHz(1T)
- DDR channel: DDR 0 + DDR 1
- DDR init use : 12100 us
- HHH
- Boot From SPI
- ucl decompress...pass
- 0x12345678
- Boot from internal device 1st SPI
- TE : 397593
- System Started
- U-boot-00000-gd05fbcd-dirty(m8_k200_v1@dualboot) (Jul 29 2015 - 19:49:24)
- clr h-ram
- DRAM: 2 GiB
- relocation Offset is: 6fec0000
- show partition table:
- part: 0, name : logo, size : 2000000
- part: 1, name : recovery, size : 2000000
- part: 2, name : misc, size : 1000000
- part: 3, name : boot, size : 1000000
- part: 4, name : linuxk, size : 1000000
- part: 5, name : system, size : 40000000
- part: 6, name : cache, size : 20000000
- part: 7, name : data, size : end
- aml_card_type=0x100
- MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
- [mmc_register] add mmc dev_num=1, port=2, if_type=6
- SDIO Port B: 0, SDIO Port C: 1
- PMU fault status:
- reg[0x9A] = 0x0d
- LSI version:04, OTP version:0c
- PMU type:RN5T618
- register usb cfg[0][1] = 7ff6fdd4
- register usb cfg[2][0] = 7ff7331c
- NAND: SPI BOOT: boot_device_flag 0
- Nand PHY driver Version: 1.01.001.0004 (c) 2013 Amlogic Inc.
- amlnf_phy_init : amlnf init flag 0
- NAND device id: ad de 94 da 74 c4 ad de
- detect NAND device: A revision 20nm NAND 8GiB H27UCG8T2A
- nand chip ce mask 1
- AML_NAND_NEW_OOB : new oob
- bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
- hynix nand get default reg value at blk:8, page:2048
- NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 0
- NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
- NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 52
- i=0,register --- nand_key
- nfcache : offset: 0x000006000000 -0x000024800000 : partitons 1 : single_chip multi_plane
- nfcode : offset: 0x00002a800000 -0x00004f800000 : partitons 6 : single_chip multi_plane
- nfdata : offset: 0x00007a000000 -0x000186000000 : partitons 1 : single_chip multi_plane
- bad block count = 0
- bad block count = 0
- bad block count = 0
- amlnf_logic_init: START
- amlnf_logic_init: COMPLETE
- get_boot_device_flag: init_ret 0
- get_boot_device_flag SPI BOOT:
- nand init success, change the device_boot_flag to 4 : spi+nand
- SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
- SF: Detected MX25L1605D with page size 256, total 2 MiB
- SPI NOR Flash have write protect!!!
- set_storage_device_flag: store 4
- vpu driver detect cpu type: m8
- vpu clk_level in dts: 7
- set vpu clk: 364300000Hz, readback: 364300000Hz(0x700)
- Net: Meson_Ethernet
- init suspend firmware done. (ret:0)
- cvbs trimming.1.v5: 0xa0, 0x0
- normal
- start normal
- wipe_data=successful
- wipe_cache=successful
- reboot_mode=normal
- mode = 8 vic = 16
- set HDMI vic: 16
- config HPLL
- config HPLL done
- reconfig packet setting done
- Hit Enter key to stop autoboot -- : 1 0
- exit abortboot: 0
- current storer:nand_key
- key save is auto select storer(nand or emmc)
- write key code version3_flush:708,prov->write:7fee8dd8
- size:4096
- arg_pages:1
- extra_page:0
- write key ok!!
- Booting...
- mac is: :00:01:db:88:06:e4
- ## ANDROID Format IMAGE
- ## Booting kernel from Legacy Image at 12000000 ...
- Image Name: Linux-3.10.86
- Image Type: ARM Linux Kernel Image (lzo compressed)
- Data Size: 6658024 Bytes = 6.3 MiB
- Load Address: 00208000
- Entry Point: 00208000
- Verifying Checksum ... OK
- Ramdisk start addr = 0x1265a800, len = 0x31d600
- Flat device tree start addr = 0x12978000, len = 0x47b4 magic=0xedfe0dd0
- Uncompressing Kernel Image ... OK
- uboot time: 2236062 us.
- EFUSE machid is not set.
- Using machid 0xf81 from environment
- From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x5326001
- Loading Ramdisk to 05008000, end 05325600 ... OK
- Loading Device Tree to 05000000, end 050077b3 ... OK
- Starting kernel ...
- [ 0.000000@0] Booting Linux on physical CPU 0x200
- [ 0.000000@0] Linux version 3.10.86 (user@Debian) (gcc version 4.9.2 (GCC) ) #1 SMP PREEMPT Fri Sep 25 21:24:05 MSK 2015
- [ 0.000000@0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
- [ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000@0] Machine: Amlogic Meson8, model: AMLOGIC
- [ 0.000000@0] physical memory start address is 0x200000
- [ 0.000000@0] reserved_end is 1f1fffff
- [ 0.000000@0]
- [ 0.000000@0] Total memory is 2046 MiB
- [ 0.000000@0] Reserved low memory from 0x06000000 to 0x1f1fffff, size: 402 MiB
- [ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x0a900000 ( 72 MiB)
- [ 0.000000@0] mesonfb1(low) : 0x0a900000 - 0x0aa00000 ( 1 MiB)
- [ 0.000000@0] deinterlace0(high) : 0x7df00000 - 0x80000000 ( 33 MiB)
- [ 0.000000@0] mesonstream0(low) : 0x0aa00000 - 0x0ca00000 ( 32 MiB)
- [ 0.000000@0] vdec0(low) : 0x0ca00000 - 0x1ca00000 (256 MiB)
- [ 0.000000@0] ppmgr0(high) : 0x7cf00000 - 0x7df00000 ( 16 MiB)
- [ 0.000000@0] vdin10(low) : 0x1ca00000 - 0x1da00000 ( 16 MiB)
- [ 0.000000@0] amlvideo20(low) : 0x1da00000 - 0x1f200000 ( 24 MiB)
- [ 0.000000@0] get storage device: storage 4
- [ 0.000000@0] value=4
- [ 0.000000@0] get_storage_device : get storage device: storage 4
- [ 0.000000@0] get_storage_device : value=4
- [ 0.000000@0] [get_storage_device] storage_flag=4
- [ 0.000000@0] [get_storage_device] the storage device does NOT relate to eMMC, storage_flag=4
- [ 0.000000@0] cma: CMA: reserved 8 MiB at 2f000000
- [ 0.000000@0] cma: Found region@0, memory base 0, size 18 MiB
- [ 0.000000@0] cma: CMA: reserved 20 MiB at 2dc00000
- [ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000@0] Meson chip version = RevC (19:C - 0:27ED)
- [ 0.000000@0] PERCPU: Embedded 8 pages/cpu @c1e72000 s12288 r8192 d12288 u32768
- [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 403216
- [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200n8 no_console_suspend storage=4 cvbsdrv=0 vdaccfg=0xa000 reboot_args=uboot_suspend logo=osd1,loaded,0x15100000,1080p,full hdmimode=1080p cvbsmode=576cvbs androidboot.firstboot=0 hdmitx= mac=00:01:db:88:06:e4 hdmitx=cecf boot=/dev/system disk=/dev/data BOOT_IMAGE=/dev/linuxk scaling_governor=ondemand scaling_min_freq=96000 scaling_max_freq=1608000 ssh
- [ 0.000000@0] cvbs performance line = 0
- [ 0.000000@0] cvbs trimming line = 0xa000
- [ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
- [ 0.000000@0] osd1:1
- [ 0.000000@0] loaded:268435459
- [ 0.000000@0] logo has been loaded
- [ 0.000000@0] 1080p:15
- [ 0.000000@0] full:2
- [ 0.000000@0] kernel get hdmimode form uboot is 1080p
- [ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
- [ 0.000000@0] ******** uboot setup mac-addr: 0:1:db:88:6:e4
- [ 0.000000@0] hdmitx: cec: Function List: enable, one touch play, one touch standby, auto power by tv
- [ 0.000000@0] hdmitx: cec: HDMI aml_read_reg32(P_AO_DEBUG_REG0):0xf
- [ 0.000000@0] hdmitx: cec: HDMI hdmi_cec_func_config:0xf
- [ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000@0] Memory: 64MB 16MB 1501MB = 1581MB total
- [ 0.000000@0] Memory: 1555264k/1555264k available, 63680k reserved, 1266688K highmem
- [ 0.000000@0] Virtual kernel memory layout:
- [ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
- [ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
- [ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000@0] .text : 0xc0008000 - 0xc0b437ac (11502 kB)
- [ 0.000000@0] .init : 0xc0b44000 - 0xc0b9d000 ( 356 kB)
- [ 0.000000@0] .data : 0xc0b9e000 - 0xc0c4d610 ( 702 kB)
- [ 0.000000@0] .bss : 0xc0c4d610 - 0xc0ebfbac (2506 kB)
- [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000@0] Preemptible hierarchical RCU implementation.
- [ 0.000000@0] NR_IRQS:256
- [ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
- [ 0.000000@0] Switching to timer-based delay loop
- [ 0.000000@0] Console: colour dummy device 80x30
- [ 0.000000@0] console [ttyS0] enabled
- [ 0.403804@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
- [ 0.414099@0] pid_max: default: 32768 minimum: 301
- [ 0.418971@0] Security Framework initialized
- [ 0.423199@0] Mount-cache hash table entries: 512
- [ 0.430894@0] CPU: Testing write buffer coherency: ok
- [ 0.433109@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
- [ 0.438658@0] Setting up static identity map for 0xc07e0990 - 0xc07e09e8
- [ 0.445443@0] L310 cache controller enabled
- [ 0.449465@0] l2x0: 8 ways, 4096 sets, CACHE_ID 0x4100a0c9, Cache size: 1048576 B
- [ 0.457035@0] AUX_CTRL 0x7ec80001, PERFETCH_CTRL 0x71000007, POWER_CTRL 0x00000000
- [ 0.465158@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
- [ 0.550138@0] write pen_release: 1
- [ 0.550341@1] CPU1: Booted secondary processor
- [ 0.550355@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
- [ 0.570131@0] write pen_release: 2
- [ 0.578272@2] CPU2: Booted secondary processor
- [ 0.578284@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
- [ 0.590127@0] write pen_release: 3
- [ 0.598267@3] CPU3: Booted secondary processor
- [ 0.598280@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
- [ 0.598341@0] Brought up 4 CPUs
- [ 0.611477@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
- [ 0.617708@0] CPU: All CPU(s) started in SVC mode.
- [ 0.622925@0] devtmpfs: initialized
- [ 0.631267@0] clkrate [ xtal ] : 24000000
- [ 0.631297@0] clkrate [ pll_sys ] : 1200000000
- [ 0.634525@0] clkrate [ pll_fixed ] : 2550000000
- [ 0.639206@0] clkrate [ pll_vid ] : 366000000
- [ 0.643632@0] TODO: clk_get_rate_hpll() is not implement in M8 now
- [ 0.649780@0] clkrate [ pll_hpll ] : 0
- [ 0.653599@0] clkrate [ pll_ddr ] : 0
- [ 0.657323@0] clkrate [ a9_clk ] : 1200000000
- [ 0.661749@0] clkrate [ clk81 ] : 141666666
- [ 0.667002@0] pinctrl core: initialized pinctrl subsystem
- [ 0.671687@0] regulator-dummy: no parameters
- [ 0.676478@0] NET: Registered protocol family 16
- [ 0.686482@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
- [ 0.690116@0] VPU driver version: v03
- [ 0.691616@0] vpu driver detect cpu type: m8
- [ 0.695865@0] load vpu_clk in dts: 364300000Hz(7)
- [ 0.700613@0] vpu_probe OK
- [ 0.703701@0] cma: Assigned CMA region with name cma_0 to amvenc_avc.0 device
- [ 0.714474@0] amlogic_gpio gpio: Probed amlogic GPIO driver
- [ 0.716094@0] register lm device lm-root
- [ 0.719871@0] register lm device lm1
- [ 0.723434@0] register lm device lm0
- [ 0.727113@0] Init pinux probe!
- [ 0.730411@0] pinmux-m8 pinmux: Probed amlogic pinctrl driver
- [ 0.735806@0] tv_init_module
- [ 0.738603@0] major number 254 for disp
- [ 0.742424@0] vout_register_server
- [ 0.745792@0] register tv module server ok
- [ 0.749939@0] major number 0 for disp
- [ 0.753603@0] register tv module server ok
- [ 0.757903@0] video2_early_init enter
- [ 0.761490@0] video2_early_init exit
- [ 0.765064@0] aml_i2c version: 20140813
- [ 0.769038@0] aml-i2c i2c-AO: add adapter aml_i2c_adap0(ed80e0a8)
- [ 0.774931@0] aml-i2c i2c-AO: aml i2c bus driver.
- [ 0.779786@0] aml-i2c i2c-A: add adapter aml_i2c_adap1(ed80d4a8)
- [ 0.785591@0] aml-i2c i2c-A: aml i2c bus driver.
- [ 0.790380@0] aml-i2c i2c-B: add adapter aml_i2c_adap2(ed80c8a8)
- [ 0.796156@0] aml-i2c i2c-B: aml i2c bus driver.
- [ 0.800946@0] aml-i2c i2c-C: add adapter aml_i2c_adap3(ed80d0a8)
- [ 0.806732@0] aml-i2c i2c-C: aml i2c bus driver.
- [ 0.811485@0] aml_pmu_init, 454
- [ 0.814506@0] call aml_dvfs_init in
- [ 0.818170@0] hdmitx: system: amhdmitx_init
- [ 0.822082@0] hdmitx: system: Ver: 2014May6
- [ 0.826300@0] hdmitx: system: amhdmitx_probe
- [ 0.830716@0] hdmitx: system: not find cec config
- [ 0.835162@0] hdmitx: system: not find vend_init_data
- [ 0.840423@0] hdmitx: system: gate/pwr cmd: 7
- [ 0.844525@0] hdmitx: system: ALREADY init VIC = 16
- [ 0.849377@0] hdmitx: system: gate/pwr cmd: 0
- [ 0.854098@1] hdmitx: system: reset intr mask
- [ 0.870389@0] hdmitx: system: irq 1
- [ 0.922417@0] bio: create slab <bio-0> at 0
- [ 0.923163@0] SCSI subsystem initialized
- [ 0.925213@0] usbcore: registered new interface driver usbfs
- [ 0.930593@0] usbcore: registered new interface driver hub
- [ 0.936052@0] usbcore: registered new device driver usb
- [ 0.941296@0] Linux video capture interface: v2.00
- [ 0.946147@0] pps_core: LinuxPPS API ver. 1 registered
- [ 0.951058@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.960649@0] PTP clock support registered
- [ 0.965043@0] mode is 15,sync_duration_den=1,sync_duration_num=60
- [ 0.970479@0] TV mode 1080p selected.
- [ 0.974100@0] already display in uboot
- [ 0.979905@0] call aml_pmu_probe_init in
- [ 0.981791@0] aml_pmus_probe, child name:rn5t618
- [ 0.986328@0] aml_pmus_probe, i2c_bus:i2c_bus_ao
- [ 0.990763@1] hdmitx: system: gate/pwr cmd: 4
- [ 0.995607@0] [RICOH]setup_supply_data, failed to get property: board_battery
- [ 1.003291@0] Allocate new i2c device: adapter:0, addr:0x32, node name:rn5t618, type:ricoh_pmu
- [ 1.011343@0] Advanced Linux Sound Architecture Driver Initialized.
- [ 1.017648@0] Bluetooth: Core ver 2.16
- [ 1.020999@0] NET: Registered protocol family 31
- [ 1.025502@0] Bluetooth: HCI device and connection manager initialized
- [ 1.032018@0] Bluetooth: HCI socket layer initialized
- [ 1.037037@0] Bluetooth: L2CAP socket layer initialized
- [ 1.042253@0] Bluetooth: SCO socket layer initialized
- [ 1.047501@0] cfg80211: Calling CRDA to update world regulatory domain
- [ 1.055302@0] Switching to clocksource Timer-E
- [ 1.078119@0] NET: Registered protocol family 2
- [ 1.078643@0] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.084251@0] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.090851@0] TCP: Hash tables configured (established 4096 bind 4096)
- [ 1.097330@0] TCP: reno registered
- [ 1.100692@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.106672@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.113201@0] NET: Registered protocol family 1
- [ 1.117768@0] RPC: Registered named UNIX socket transport module.
- [ 1.123661@0] RPC: Registered udp transport module.
- [ 1.128510@0] RPC: Registered tcp transport module.
- [ 1.133356@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.140017@0] wifi_dev_probe
- [ 1.142807@0] wifi_dt : interrupt_pin=GPIOX_21
- [ 1.147228@0] wifi_dt : irq_num=null
- [ 1.150789@0] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
- [ 1.155898@0] wifi_dt : power_on_pin=GPIOAO_6
- [ 1.160249@0] wifi_dt : power_on_pin2=GPIOX_11
- [ 1.164652@0] interrupt_pin=133, irq_num=4, irq_trigger_type=0, power_on_pin=6,clock_32k_pin=122
- [ 1.173591@0] Unpacking initramfs...
- [ 1.184851@0] Freeing initrd memory: 3188K (c4e08000 - c5125000)
- [ 1.187099@0] audit: initializing netlink socket (disabled)
- [ 1.188542@1] hdmitx: system: gate/pwr cmd: 5
- [ 1.188543@1] hdmitx: edid: edid ready
- [ 1.188545@1] hdmitx: system: gate/pwr cmd: 4
- [ 1.203204@0] type=2000 audit(1.100:1): initialized
- [ 1.208470@0] bounce pool size: 64 pages
- [ 1.217204@0] VFS: Disk quotas dquot_6.5.2
- [ 1.217422@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 1.224382@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 1.229803@0] NFS: Registering the id_resolver key type
- [ 1.233874@0] Key type id_resolver registered
- [ 1.238190@0] Key type id_legacy registered
- [ 1.242765@0] fuse init (API version 7.22)
- [ 1.246967@0] msgmni has been set to 625
- [ 1.251352@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
- [ 1.257869@0] io scheduler noop registered
- [ 1.261948@0] io scheduler deadline registered
- [ 1.266500@0] io scheduler cfq registered (default)
- [ 1.274313@0] loop: module loaded
- [ 1.275181@0] tun: Universal TUN/TAP device driver, 1.6
- [ 1.279735@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 1.286176@0] PPP generic driver version 2.4.2
- [ 1.290656@0] PPP BSD Compression module registered
- [ 1.295307@0] PPP Deflate Compression module registered
- [ 1.300521@0] PPP MPPE Compression module registered
- [ 1.305453@0] NET: Registered protocol family 24
- [ 1.310158@0] usbcore: registered new interface driver asix
- [ 1.315708@0] usbcore: registered new interface driver ax88179_178a
- [ 1.321932@0] usbcore: registered new interface driver cdc_ether
- [ 1.327886@0] usbcore: registered new interface driver dm9601
- [ 1.333618@0] usbcore: registered new interface driver net1080
- [ 1.339426@0] usbcore: registered new interface driver cdc_subset
- [ 1.345479@0] usbcore: registered new interface driver zaurus
- [ 1.351230@0] usbcore: registered new interface driver cdc_ncm
- [ 1.357303@0] usbcore: registered new interface driver usb-storage
- [ 1.363363@0] mousedev: PS/2 mouse device common for all mice
- [ 1.368934@0] i2c /dev entries driver
- [ 1.373151@0] lirc_dev: IR Remote Control driver registered, major 246
- [ 1.379052@0] IR NEC protocol handler initialized
- [ 1.383722@0] IR RC5(x) protocol handler initialized
- [ 1.388672@0] IR RC6 protocol handler initialized
- [ 1.393343@0] IR JVC protocol handler initialized
- [ 1.398024@0] IR Sony protocol handler initialized
- [ 1.398524@1] hdmitx: system: gate/pwr cmd: 5
- [ 1.398526@1] hdmitx: edid: edid ready
- [ 1.398531@1] hdmitx: edid: check sum valid
- [ 1.398532@1] hdmitx: edid: check sum valid
- [ 1.398534@1] hdmitx: edid: blk0 raw data
- [ 1.398556@1] 00ffffffffffff00410c00000101010104180103804024780af9aba2554a9a25
- [ 1.398576@1] 0f474a2108008180010101010101010101010101010104740030f2705a80b058
- [ 1.398596@1] 8a0080682100001e023a801871382d40582c450080682100001e000000fc0050
- [ 1.398616@1] 48494c495053204654560a20000000fd00184c1e531e000a2020202020200132
- [ 1.398617@1]
- [ 1.398618@1] hdmitx: edid: blk1 raw data
- [ 1.398639@1] 02033c714d1f102021140513041102150601290907031507503d07c083010000
- [ 1.398658@1] 7b030c002000003c20c86e020103014100fc20306070281038106810023a80d0
- [ 1.398678@1] 72382d40102c458080682100001e011d803e73382d407e2c458080682100001e
- [ 1.398698@1] 011d80d0721c1620102c258080682100009e000000000000000000000000005b
- [ 1.398699@1]
- [ 1.398732@1] hdmitx: edid: find IEEEOUT
- [ 1.398772@1] hdmitx: video: get current mode: 1080p
- [ 1.398780@1] is_similar_hdmi_vic[325] vic_old=16,mode_new=15
- [ 1.398783@1] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
- [ 1.398786@1] hdmitx: audio: audio channel num is 0
- [ 1.398791@1] hdmitx: audio: SPDIF
- [ 1.398802@1] hdmitx: audio: current VIC: 16
- [ 1.398803@1] hdmitx: audio: audio sample rate: 0
- [ 1.398805@1] hdmitx: audio: set audio N para
- [ 1.398812@1] hdmitx: audio: PCM out to HDMI
- [ 1.419359@1] hdmitx: audio: Time out: AIU_HDMI_CLK_DATA_CTRL
- [ 1.419361@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 1.419362@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 1.419416@1] hdmitx: cec: CEC not ready
- [ 1.554501@0] IR RC5 (streamzap) protocol handler initialized
- [ 1.560215@0] IR SANYO protocol handler initialized
- [ 1.565061@0] IR MCE Keyboard/mouse protocol handler initialized
- [ 1.571052@0] IR LIRC bridge handler initialized
- [ 1.575751@0] usbcore: registered new interface driver uvcvideo
- [ 1.581540@0] USB Video Class driver (1.1.1)
- [ 1.586077@0] device-mapper: uevent: version 1.0.3
- [ 1.590854@0] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
- [ 1.599329@0] Bluetooth: HCI UART driver ver 2.2
- [ 1.603728@0] Bluetooth: HCI H4 protocol initialized
- [ 1.609010@0] hidraw: raw HID events driver (C) Jiri Kosina
- [ 1.619061@0] usbcore: registered new interface driver usbhid
- [ 1.619937@0] usbhid: USB HID core driver
- [ 1.624318@0] zram: Created 1 device(s) ...
- [ 1.628453@0] ashmem: initialized
- [ 1.631526@0] logger: created 256K log 'log_main'
- [ 1.636203@0] logger: created 256K log 'log_events'
- [ 1.641084@0] logger: created 256K log 'log_radio'
- [ 1.645819@0] logger: created 256K log 'log_system'
- [ 1.650826@0] vout_init_module
- [ 1.653614@0] start init vout module
- [ 1.657363@0] create vout attribute ok
- [ 1.661795@0] ge2d_init
- [ 1.663710@0] ge2d_dev major:243
- [ 1.667212@0] ge2d start monitor
- [ 1.670346@0] osd_init
- [ 1.670352@1] ge2d workqueue monitor start
- [ 1.676825@0] osd_probe, vinfo:c083630c
- [ 1.681121@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=73728K
- [ 1.688772@0] osd_probe, mydef_var:c0bfb0e0, vinfo:c083630c
- [ 1.694306@0] init fbdev bpp is :32
- [ 1.697859@0] ---------------clear framebuffer0 memory
- [ 1.759887@0] Console: switching to colour frame buffer device 240x67
- [ 1.786398@0] Frame buffer memory assigned at phy:0x0a900000, vir:0xf0200000, size=1024K
- [ 1.792222@0] osd_probe, mydef_var:c0bfb0e0, vinfo:c083630c
- [ 1.797760@0] don't find to display_size_default from mesonfb-dts
- [ 1.803837@0] init fbdev bpp is :16
- [ 1.819656@0] osd probe ok
- [ 1.819822@0] osd_ext_init
- [ 1.820203@0] vout2_init_module enter
- [ 1.829496@0] amlvideo-000: V4L2 device registered as video10
- [ 1.829796@0] amlvideo2: V4L2 device registered as video11
- [ 1.835371@0] ionvideo-000: V4L2 device registered as video13
- [ 1.840796@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
- [ 1.849603@0] aml_wdt_driver_init,301
- [ 1.852830@0] ** disable watchdog
- [ 1.856295@0] keys===========================================
- [ 1.861878@0] keys_devno=f000000
- [ 1.865247@0] securitykey: device aml_keys created
- [ 1.869853@0] amlkeys=0
- [ 1.872324@0] platform_driver_register--aml_keys_driver--------------------
- [ 1.879264@0] key unify config unifykey-num is 6
- [ 1.883799@0] key unify fact unifykey-num is 6
- [ 1.888224@0] aml_unifykeys_probe:694=============unifykey_devno:ef00000
- [ 1.895060@0] unifykey: device unifykeys created ok
- [ 1.899824@0] platform_driver_register--unifykey management driver--------------------
- [ 1.907958@0] set uart_ao pinmux use pinctrl subsystem
- [ 1.912840@0] P_AO_RTI_PIN_MUX_REG:78005861
- [ 1.916995@0] start uart_ao_ttyS0:(irq = 122)
- [ 1.921338@0] register uart_ao ok
- [ 1.924812@0] set uart_a pinmux use pinctrl subsystem
- [ 1.929655@0] P_AO_RTI_PIN_MUX_REG:78005861
- [ 1.933801@0] start uart_a_ttyS1:(irq = 58)
- [ 1.937956@0] register uart_a ok
- [ 1.941376@0] start uart_d_ttyS4:(irq = 126)
- [ 1.945407@0] register uart_d ok
- [ 1.948774@0] dwc_otg: version 3.10a 12-MAY-2014
- [ 1.953238@0] dwc_otg_driver_probe NOT match
- [ 1.957485@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
- [ 1.966068@0] USB (1) use clock source: XTAL input
- [ 1.991874@0] Core Release: 3.10a
- [ 1.991899@0] Setting default values for core params
- [ 1.994497@0] curmode: 1, host_only: 1
- [ 2.018369@0] Using Buffer DMA mode
- [ 2.018394@0] OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 2.020728@0] Working on port type = HOST
- [ 2.025410@0] dwc_otg lm1: DWC OTG Controller
- [ 2.029087@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
- [ 2.035738@0] dwc_otg lm1: irq 63, io mem 0x00000000
- [ 2.040689@0] -------hcd->flags.d32 = 0
- [ 2.044492@0] Init: Port Power? op_state=1
- [ 2.048568@0] Init1: Power Port (0)
- [ 2.052101@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.058978@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.066321@0] usb usb1: Product: DWC OTG Controller
- [ 2.071196@0] usb usb1: Manufacturer: Linux 3.10.86 dwc_otg_hcd
- [ 2.077069@0] usb usb1: SerialNumber: lm1
- [ 2.081455@0] hub 1-0:1.0: USB hub found
- [ 2.084965@0] hub 1-0:1.0: 1 port detected
- [ 2.089232@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
- [ 2.097617@0] USB (0) use clock source: XTAL input
- [ 2.123447@0] Core Release: 3.10a
- [ 2.123471@0] Setting default values for core params
- [ 2.126066@0] curmode: 1, host_only: 0
- [ 2.189897@0] Using Buffer DMA mode
- [ 2.189922@0] OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 2.192253@0] Working on port type = OTG
- [ 2.196153@0] Current port type: SLAVE
- [ 2.200005@0] dwc_otg lm0: DWC OTG Controller
- [ 2.204232@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
- [ 2.210926@0] dwc_otg lm0: irq 62, io mem 0x00000000
- [ 2.215862@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.222792@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.230154@0] usb usb2: Product: DWC OTG Controller
- [ 2.234989@0] usb usb2: Manufacturer: Linux 3.10.86 dwc_otg_hcd
- [ 2.240903@0] usb usb2: SerialNumber: lm0
- [ 2.245229@0] hub 2-0:1.0: USB hub found
- [ 2.248803@0] hub 2-0:1.0: 1 port detected
- [ 2.252957@0] Dedicated Tx FIFOs mode
- [ 2.256715@0] using timer detect id change, ed933400
- [ 2.261603@0] boot_device_flag : 0
- [ 2.264806@0] ===========================================amlnf_init:642,nand device tree ok,dev-name:nand
- [ 2.274345@0] Nand PHY driver Version: 2.01.001.0006 (c) 2013 Amlogic Inc.
- [ 2.280057@3] HOST mode
- [ 2.283636@0] amlnf_phy_init : amlnf init flag 0
- [ 2.288262@1] Indeed it is in host mode hprt0 = 00021501
- [ 2.288298@0] ######STS IRQ mode for nand driver
- [ 2.288349@0] NAND device id: ad de 94 da 74 c4 ad de
- [ 2.288354@0] detect NAND device: A revision 20nm NAND 8GiB H27UCG8T2A
- [ 2.308229@3] -------hcd->flags.d32 = 0
- [ 2.308254@3] Init: Port Power? op_state=1
- [ 2.308256@3] Init1: Power Port (0)
- [ 2.308260@3] [RN5T618]rn5t618_otg_change, driver is not ready, do it later
- [ 2.308263@3] set usb port power on (board gpio 15)!
- [ 2.333094@0] AML_NAND_NEW_OOB : new oob
- [ 2.336759@0] bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
- [ 2.344664@0] boot_device_flag = 0
- [ 2.349764@0] hynix nand get default reg value at blk:8, page:2048
- [ 2.354822@0] NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 0
- [ 2.366601@0] NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
- [ 2.371193@0] nand shipped bbt at block 6
- [ 2.390964@0] NAND CKECK : arg phyp: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 1
- [ 2.427723@0] NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 54
- [ 2.430867@0] i=0,register --- nand_key
- [ 2.434354@0] amlnand_phydev_init,1179,phydev->offset=6000000,phydev->size=24800000
- [ 2.441979@0] amlnand_phydev_init,1179,phydev->offset=2a800000,phydev->size=4f800000
- [ 2.449693@0] amlnand_phydev_init,1179,phydev->offset=7a000000,phydev->size=186000000
- [ 2.457476@0] nfcache : offset: 0x000006000000 -0x000024800000 : partitons 1 : single_chip multi_plane
- [ 2.467024@0] nfcode : offset: 0x00002a800000 -0x00004f800000 : partitons 6 : single_chip multi_plane
- [ 2.476564@0] nfdata : offset: 0x00007a000000 -0x000186000000 : partitons 1 : single_chip multi_plane
- [ 2.487967@0] bad block count = 0
- [ 2.487967@0]
- [ 2.495109@0] bad block count = 0
- [ 2.495109@0]
- [ 2.508223@1] usb 1-1: new high-speed USB device number 2 using dwc_otg
- [ 2.509415@3] Indeed it is in host mode hprt0 = 00001101
- [ 2.516081@0] bad block count = 0
- [ 2.516081@0]
- [ 2.519445@0] amlnand_add_nftl:
- [ 2.522545@0] Creating 1 ntd partitions
- [ 2.526356@0] block_num 146
- [ 2.531134@0] ------init_ntd
- [ 2.532457@0] ntd: Giving out device 0 to nfcache
- [ 2.536762@0] Creating 6 ntd partitions
- [ 2.540601@0] block_num 318
- [ 2.547792@0] ntd: Giving out device 1 to nfcode
- [ 2.548026@0] Creating 1 ntd partitions
- [ 2.551871@0] block_num 1560
- [ 2.575343@0] ntd: Giving out device 2 to nfdata
- [ 2.575844@0] boot_device_flag : 0
- [ 2.577699@0] register_ntd_blktrans start
- [ 2.581741@0] ntd device 250!
- [ 2.584634@0] ntd->name: nfcache
- [ 2.587848@0] adjust_block_num : 4,reserved_block_ratio 10
- [ 2.593325@0] nftl version 150204a
- [ 2.596683@0] nftl build Feb 4 2015_21:22:11
- [ 2.601047@0] nftl part attr 0
- [ 2.605925@0] nftl start:146,17
- [ 2.607330@0] first
- [ 2.688536@0] average_erase_count:0
- [ 2.688562@0] second 11,129
- [ 2.689158@0] part->max_discard_block = 4
- [ 2.699562@0] all block full!!
- [ 2.699583@0] all discard block full!!
- [ 2.700705@0] free block cnt = 135
- [ 2.704089@0] new current block is 139
- [ 2.707812@0] total discard page count is 0
- [ 2.709421@3] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
- [ 2.709426@3] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
- [ 2.709430@3] usb 1-1: Product: USB2.0 Hub
- [ 2.710020@3] hub 1-1:1.0: USB hub found
- [ 2.710292@3] hub 1-1:1.0: 4 ports detected
- [ 2.711856@3] Indeed it is in host mode hprt0 = 00021501
- [ 2.743566@0] create_part_list:1238,current_used_discard_block=133,current_discard_block_used_count=16
- [ 2.753377@0] unmappig_pages=31466,discarded_pages=0,mapping_pages=1558
- [ 2.759415@0] nftl ok!
- [ 2.762153@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 2.766717@0] aml_nftl_add_ntd ok
- [ 2.769640@0] ntd device 250!
- [ 2.772569@0] ntd->name: nfcode
- [ 2.775686@0] adjust_block_num : 4,reserved_block_ratio 10
- [ 2.781175@0] nftl version 150204a
- [ 2.784526@0] nftl build Feb 4 2015_21:22:11
- [ 2.788912@0] nftl part attr 0
- [ 2.795967@0] nftl start:318,33
- [ 2.796288@0] first
- [ 2.888230@3] usb 2-1: new full-speed USB device number 2 using dwc_otg
- [ 2.889342@3] Indeed it is in host mode hprt0 = 00021501
- [ 2.959172@0] average_erase_count:0
- [ 2.959199@0] second 292,285
- [ 2.959880@0] part->max_discard_block = 4
- [ 3.090337@3] usb 2-1: New USB device found, idVendor=046d, idProduct=c52b
- [ 3.091575@3] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- [ 3.098864@3] usb 2-1: Product: USB Receiver
- [ 3.103102@3] usb 2-1: Manufacturer: Logitech
- [ 3.113975@3] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-lm0-1/input2
- [ 3.133957@0] current_block1:24
- [ 3.137896@0] recover_current_block_mapping invalid page data!!
- [ 3.138746@0] recover_current_block_mapping invalid page data!!
- [ 3.144639@0] recover_current_block_mapping invalid page data!!
- [ 3.150559@0] recover_current_block_mapping invalid page data!!
- [ 3.156432@0] recover_current_block_mapping invalid page data!!
- [ 3.162342@0] recover_current_block_mapping invalid page data!!
- [ 3.168161@0] all discard block full!!
- [ 3.171496@0] free block cnt = 45
- [ 3.174665@0] new current block is 26
- [ 3.198569@3] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
- [ 3.300312@3] usb 1-1.1: New USB device found, idVendor=05e3, idProduct=0718
- [ 3.301736@3] usb 1-1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=2
- [ 3.309194@3] usb 1-1.1: Product: USB Storage
- [ 3.313522@3] usb 1-1.1: SerialNumber: 000000000033
- [ 3.319092@3] usb-storage 1-1.1:1.0: USB Mass Storage device detected
- [ 3.321348@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
- [ 3.333243@3] scsi0 : usb-storage 1-1.1:1.0
- [ 3.804974@0] recover_current_block_mapping : fill the current block, from page 255
- [ 3.806984@0] total discard page count is 0
- [ 3.811168@0] create_part_list:1238,current_used_discard_block=25,current_discard_block_used_count=333
- [ 3.821667@0] unmappig_pages=7710,discarded_pages=0,mapping_pages=65250
- [ 3.827007@0] nftl ok!
- [ 3.829907@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.834425@3] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.839020@3] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.843585@3] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.848163@3] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.852792@3] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.857292@3] aml_nftl_add_ntd ok
- [ 3.860233@3] ntd device 250!
- [ 3.863167@3] ntd->name: nfdata
- [ 3.866289@3] adjust_block_num : 4,reserved_block_ratio 10
- [ 3.871757@3] nftl version 150204a
- [ 3.875129@3] nftl build Feb 4 2015_21:22:11
- [ 3.879606@3] nftl part attr 0
- [ 3.903236@3] nftl start:1560,146
- [ 3.904583@3] first
- [ 4.727618@3] found discard block:1524
- [ 4.745404@3] average_erase_count:0
- [ 4.745453@3] second 322,1414
- [ 4.746211@3] part->max_discard_block = 4
- [ 4.938317@3] current_block1:1237
- [ 4.949580@3] recover_current_block_mapping invalid page data!!
- [ 4.950443@3] recover_current_block_mapping invalid page data!!
- [ 4.956346@3] recover_current_block_mapping invalid page data!!
- [ 4.962239@3] recover_current_block_mapping invalid page data!!
- [ 4.968129@3] recover_current_block_mapping invalid page data!!
- [ 4.975352@3] recover_current_block_mapping invalid page data!!
- [ 4.980379@3] currnet_discard_block1:1524
- [ 4.985144@3] reach the last discard page:2
- [ 4.988639@3] free block cnt = 1265
- [ 4.990955@3] new current block is 1238
- [ 5.140980@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
- [ 5.624368@0] recover_current_block_mapping : fill the current block, from page 255
- [ 5.626378@0] total discard page count is 2
- [ 5.630564@0] create_part_list:1238,current_used_discard_block=1524,current_discard_block_used_count=36
- [ 5.646751@0] unmappig_pages=322324,discarded_pages=1849,mapping_pages=37811
- [ 5.648156@0] nftl ok!
- [ 5.651126@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 5.655577@3] aml_nftl_add_ntd ok
- [ 5.658442@3] init_aml_nftl end
- [ 5.661678@3] ethernet_driver probe!
- [ 5.665074@3] Please config phy interface.
- [ 5.669243@3] Please config savepowermode.
- [ 5.673307@3] Please config reset_pin_enable.
- [ 5.677639@3] Please config reset_delay.
- [ 5.681553@3] Please config reset_pin.
- [ 5.685271@3] ethernetinit(dbg[c0c01b84]=1)
- [ 5.689453@3] ethernet base addr is fe0c0000
- [ 5.693678@3] write mac add to:ed907588: 00 01 db 88 06 e4 |......|
- [ 5.702529@3] libphy: AMLMAC MII Bus: probed
- [ 5.704164@3] eth0: PHY ID 02430c54 at 0 IRQ -1 (0:00) active
- [ 5.711685@3] Amlogic A/V streaming port init
- [ 5.715756@3] buffersize=262144,0,start=0
- [ 5.718225@3] Subtitle stbuf alloced at 0xecc40000, size = 262144
- [ 5.724278@3] changed the (2) buffer size from 0 to 262144
- [ 5.730025@3] init vdec memsource ca00000->1c9fffff
- [ 5.734793@3] [tsync_pcr_init]init success.
- [ 5.738850@3] amvideocap_init_module
- [ 5.742636@3] regist mpeg12 codec profile
- [ 5.746469@3] regist mpeg4 codec profile
- [ 5.750292@3] amvdec_vc1 module init
- [ 5.753923@3] regist vc1 codec profile
- [ 5.757563@3] amvdec_h264 module init
- [ 5.761324@3] regist h264 codec profile
- [ 5.765019@3] amvdec_h264mvc module init
- [ 5.769013@3] regist hmvc codec profile
- [ 5.772749@3] amvdec_h264_4k2k module init
- [ 5.776895@3] scsi 0:0:0:0: Direct-Access USB TO I DE/SATA Device 0016 PQ: 0 ANSI: 4
- [ 5.785151@2] regist h264_4k2k codec profile
- [ 5.788076@3] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
- [ 5.789079@3] sd 0:0:0:0: [sda] Asking for cache data failed
- [ 5.789083@3] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 5.792826@3] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
- [ 5.793826@3] sd 0:0:0:0: [sda] Asking for cache data failed
- [ 5.793830@3] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 5.793835@3] sd 0:0:0:0: [sda] Attached SCSI disk
- [ 5.830461@2] amvdec_h265 module init
- [ 5.834225@2] regist hevc_unsupport codec profile
- [ 5.838879@2] regist mjpeg codec profile
- [ 5.842670@2] amvdec_real module init
- [ 5.846399@2] amvdec_avs module init
- [ 5.850079@2] amvenc_avc memory resource undefined.
- [ 5.854719@2] encode_wq_init.
- [ 5.857668@2] encode start monitor.
- [ 5.861219@2] encode workqueue monitor start.
- [ 5.865731@2] jpegenc module init
- [ 5.869051@2] alloc_keep_buffer keep_y_addr ec600000
- [ 5.873713@2] alloc_keep_buffer keep_u_addr ecd00000
- [ 5.878659@2] alloc_keep_buffer keep_v_addr ec200000
- [ 5.883585@2] yaddr=ec600000,u_addr=ecd00000,v_addr=ec200000
- [ 5.889535@2] create_ge2d_work_queue video task ok
- [ 5.894074@2] video2_init enter
- [ 5.897652@2]
- [ 5.897652@2]
- [ 5.897652@2] VECM init
- [ 5.897652@2]
- [ 5.905011@2] efuse===========================================
- [ 5.910752@2] efuse: device efuse created
- [ 5.914629@2] efuse--------------------------------------------
- [ 5.920434@2] SARADC Driver init.
- [ 5.923858@2] __saradc_probe__
- [ 6.068340@0] saradc calibration: ref_val = 509
- [ 6.068370@0] saradc calibration: ref_nominal = 512
- [ 6.072101@0] saradc calibration: coef = 4080
- [ 6.076509@0] Remote Driver
- [ 6.079278@0] Remote platform_data g_remote_base=fe600580
- [ 6.084585@0] set drvdata completed
- [ 6.088151@0] device_create_file completed
- [ 6.092691@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
- [ 6.099867@0] input_register_device completed
- [ 6.104134@0] [0xffffff00] = 0x1dd0190
- [ 6.107797@0] [0xffffff04] = 0xf800ca
- [ 6.111464@0] [0xffffff08] = 0x82006e
- [ 6.115078@0] [0xffffff0c] = 0x3c0030
- [ 6.118737@0] [0xffffff10] = 0x30fa0013
- [ 6.122549@0] [0xffffff18] = 0x6f19000
- [ 6.126260@0] [0xffffff1c] = 0xbe40
- [ 6.129757@0] [0x0] = 0xfa00a0
- [ 6.132761@0] [0x4] = 0xfa00a0
- [ 6.135795@0] [0x8] = 0xfa00a0
- [ 6.138864@0] [0xc] = 0x640030
- [ 6.141863@0] [0x10] = 0x30fa0013
- [ 6.145157@0] [0x18] = 0x961b800
- [ 6.148382@0] [0x1c] = 0x9740
- [ 6.151311@0] [0x20] = 0x104
- [ 6.154184@0] [0x24] = 0x0
- [ 6.156859@0] [0x28] = 0x0
- [ 6.159563@0] set_remote_mode[69]
- [ 6.162857@0] remote config major:234
- [ 6.166776@0] physical address:0x2dbba000
- [ 6.170684@0] GPIO Keypad Driver init.
- [ 6.174344@0] ==gpio_key_probe==
- [ 6.177510@0] reg:2620,clearmask=400040,setmask=1
- [ 6.182258@0] reg:2622,clearmask=ff0000,set pin=3
- [ 6.186939@0] reg:2623,clearmask=7000000,setmask=7
- [ 6.191761@1] reg:2620,clearmask=800080,setmask=10001
- [ 6.196821@1] reg:2622,clearmask=ff000000,set pin=3
- [ 6.201675@1] reg:2623,clearmask=70000000,setmask=7
- [ 6.206566@1] power key(116) registed.
- [ 6.206568@0] key 116 up
- [ 6.212948@1] input: gpio_keypad as /devices/platform/gpio_keypad.6/input/input1
- [ 6.220291@1] gpio keypad register input device completed.
- [ 6.225694@1] gpio keypad major:233
- [ 6.229541@1] VFD Driver################################
- [ 6.234561@1] ###################vfd_probe
- [ 6.238698@1] VFD init ---CONFIG_VFD_TM1628####vfd_stb_gpio is 32
- [ 6.244762@1] ####vfd_clk_gpio is 35
- [ 6.248321@1] ####vfd_stb_gpio is 34
- [ 6.251865@1] ####################come here #####################
- [ 6.273360@1] up vfd key(103) registed.
- [ 6.273386@1] down vfd key(108) registed.
- [ 6.275543@1] right vfd key(106) registed.
- [ 6.279624@1] back vfd key(158) registed.
- [ 6.283604@1] left vfd key(105) registed.
- [ 6.287592@1] ok vfd key(232) registed.
- [ 6.291590@1] input: vfd_keypad as /devices/platform/m1-vfd.0/input/input2
- [ 6.298394@1] vfd config major:232
- [ 6.302008@1] spi_nor_init
- [ 6.304523@1] amlogic_spi_nor_probe:
- [ 6.307966@1] amlogic_spi->state_name:default
- [ 6.312442@1] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
- [ 6.319962@1] check_storage_device : spi boot_device_flag : 0
- [ 6.325558@1] spi_nor_probe
- [ 6.328369@1] spi_nor apollospi:32766: mx25l160 (2048 Kbytes)
- [ 6.334151@1] Creating 2 MTD partitions on "apollospi:32766":
- [ 6.339789@1] 0x000000000000-0x000000100000 : "bootloader"
- [ 6.345963@1] 0x000000100000-0x000000110000 : "ubootenv"
- [ 6.351185@1] amlogic_spi_nor_probe over
- [ 6.354569@1] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
- [ 6.364339@1] host->base fe108c20
- [ 6.367195@1] pdata->caps 7
- [ 6.369954@1] pdata->caps2 0
- [ 6.372803@1] get property: port, value:0x00000001
- [ 6.379310@1] get property: ocr_avail, value:0x00200000
- [ 6.385803@1] get property: f_min, value:0x000493e0
- [ 6.392310@1] get property: f_max, value:0x02faf080
- [ 6.398818@1] get property: max_req_size, value:0x00020000
- [ 6.405307@1] get property: irq_in, value:0x00000003
- [ 6.411816@1] get property: irq_out, value:0x00000005
- [ 6.418318@1] get property: gpio_cd, str:CARD_6
- [ 6.424292@1] get property: pinname, str:sd
- [ 6.429933@1] get property: jtag_pin, str:CARD_0
- [ 6.435906@1] get property: card_type, value:0x00000005
- [ SÅ]
- [ 6.648245@1]
- [ 6.648245@1]
- [ 6.648245@1]
- [ 6.657512@1] [0;40;32m JTAG in[0m
- [ 6.698239@1] reg:2620,clearmask=80008,setmask=10001
- [ 6.698277@1] reg:2621,clearmask=ff000000,set pin=64
- [ 6.702589@1] reg:2623,clearmask=7000,setmask=7
- [ 6.707097@1] reg:2620,clearmask=200020,setmask=1
- [ 6.711864@1] reg:2622,clearmask=ff00,set pin=64
- [ 6.716458@1] reg:2623,clearmask=700000,setmask=7
- [ 6.721280@1] pdata->caps 80000507
- [ 6.724519@1] pdata->caps2 0
- [ 6.727381@1] get property: port, value:0x00000002
- [ 6.733896@1] get property: ocr_avail, value:0x00200000
- [ 6.740390@1] get property: f_min, value:0x000493e0
- [ 6.746884@1] get property: f_max, value:0x02faf080
- [ 6.753392@1] get property: f_max_w, value:0x02faf080
- [ 6.759893@1] get property: max_req_size, value:0x00020000
- [ 6.766392@1] get property: pinname, str:emmc
- [ 6.772203@1] get property: card_type, value:0x00000001
- [ 6.778704@1] get property: gpio_dat3, str:BOOT_3
- [ 6.784678@1] [is_emmc_exist] host->storage_flag=4, POR_BOOT_VALUE=5
- [ 6.791013@1] [aml_sdio_probe]: there is not eMMC/tsd, skip sdio_c dts config!
- [ 6.798220@1] pdata->caps 107
- [ 6.801146@1] pdata->caps2 0
- [ 6.804008@1] get property: port, value:0x00000000
- [ 6.810514@1] get property: ocr_avail, value:0x00200000
- [ 6.817010@1] get property: f_min, value:0x000493e0
- [ 6.823516@1] get property: f_max, value:0x02faf080
- [ 6.830028@1] get property: max_req_size, value:0x00020000
- [ 6.836516@1] get property: pinname, str:sdio
- [ 6.842328@1] get property: card_type, value:0x00000003
- [ 6.888235@1] [aml_sdio_probe] aml_sdio_probe() success!
- [ 6.888527@1] [dsp]DSP start addr 0xc5e00000
- [ 6.892172@1] [dsp]register dsp to char divece(257)
- [ 6.897430@1] amlogic audio spdif interface device init!
- [ 6.902357@1] name=nand_key nand_key
- [ 6.906209@1] register_aes_algorithm:488,new way
- [ 6.910814@1] key name:keyexample, key data:1234567890
- [ 6.916196@1] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
- [ 6.922889@1] input: rn5t618_pmu as /devices/i2c-0/0-0032/rn5t618_pmu.0/input/input3
- [ 6.929493@1] [RN5T618] NO BATTERY_PARAMETERS FOUND
- [ 6.934195@1] [RN5T618]rn5t618_otg_change, value:1, is_short:0
- [ 6.941101@1] register 0xB3:33
- [ 6.946071@1] ------------[ cut here ]------------
- [ 6.947812@1] WARNING: at kernel/workqueue.c:1368 __queue_work+0x248/0x368()
- [ 6.954823@1] Modules linked in:
- [ 6.958033@1] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.10.86 #1
- [ 6.964201@1] [<c0014d84>] (unwind_backtrace+0x0/0xec) from [<c0011dac>] (show_stack+0x10/0x14)
- [ 6.972860@1] [<c0011dac>] (show_stack+0x10/0x14) from [<c00321d8>] (warn_slowpath_common+0x54/0x6c)
- [ 6.981960@1] [<c00321d8>] (warn_slowpath_common+0x54/0x6c) from [<c003228c>] (warn_slowpath_null+0x1c/0x24)
- [ 6.991755@1] [<c003228c>] (warn_slowpath_null+0x1c/0x24) from [<c004c0d8>] (__queue_work+0x248/0x368)
- [ 7.001031@1] [<c004c0d8>] (__queue_work+0x248/0x368) from [<c004c238>] (queue_work_on+0x40/0x4c)
- [ 7.009877@1] [<c004c238>] (queue_work_on+0x40/0x4c) from [<c05485f8>] (rn5t618_otg_change+0x184/0x1ac)
- [ 7.019236@1] [<c05485f8>] (rn5t618_otg_change+0x184/0x1ac) from [<c05488cc>] (rn5t618_battery_probe+0x2ac/0x5b0)
- [ 7.029465@1] [<c05488cc>] (rn5t618_battery_probe+0x2ac/0x5b0) from [<c0314414>] (driver_probe_device+0xd4/0x21c)
- [ 7.039691@1] [<c0314414>] (driver_probe_device+0xd4/0x21c) from [<c0314608>] (__driver_attach+0x68/0x8c)
- [ 7.049229@1] [<c0314608>] (__driver_attach+0x68/0x8c) from [<c03128bc>] (bus_for_each_dev+0x4c/0xa4)
- [ 7.058414@1] [<c03128bc>] (bus_for_each_dev+0x4c/0xa4) from [<c0313afc>] (bus_add_driver+0xd0/0x25c)
- [ 7.067601@1] [<c0313afc>] (bus_add_driver+0xd0/0x25c) from [<c0314c24>] (driver_register+0xa8/0x140)
- [ 7.076790@1] [<c0314c24>] (driver_register+0xa8/0x140) from [<c0547184>] (rn5t618_battery_init+0x10/0x34)
- [ 7.086412@1] [<c0547184>] (rn5t618_battery_init+0x10/0x34) from [<c0008544>] (do_one_initcall+0xa0/0x148)
- [ 7.096038@1] [<c0008544>] (do_one_initcall+0xa0/0x148) from [<c0b44bdc>] (kernel_init_freeable+0x130/0x218)
- [ 7.105833@1] [<c0b44bdc>] (kernel_init_freeable+0x130/0x218) from [<c07d29b4>] (kernel_init+0x8/0x160)
- [ 7.115194@1] [<c07d29b4>] (kernel_init+0x8/0x160) from [<c000e0a0>] (ret_from_fork+0x14/0x34)
- [ 7.123778@1] ---[ end trace f5fd1c5dc05b9217 ]---
- [ 7.234890@1] vdin_drv_init: major 230
- [ 7.235156@1] vdin1 mem_start = 0x1ca00000, mem_size = 0x1000000
- [ 7.239000@1] vdin_drv_probe: driver initialized ok
- [ 7.243963@1] amvdec_656in module: init.
- [ 7.247735@1] amvdec_656in_init_module:major 229
- [ 7.252717@1] amvdec_656in probe ok.
- [ 7.256300@1] amvdec_csi probe ok.
- [ 7.259348@1] [viuin..]viuin_init_module viuin module init
- [ 7.264945@1] [viuin..]viuin_probe probe ok.
- [ 7.269377@1] [isp..]isp_probe isp probe ok.
- [ 7.273288@1] [sii9233a_drv_init] Ver: 2013Nov12
- [ 7.279016@1] amaudio2: device amaudio2 created
- [ 7.282497@1] Error: Didn't get power valid value --- wifi_power_probe 323
- [ 7.289182@1] wifi_power power_gpio is 6
- [ 7.293070@1] wifi_power power_gpio2 is 123
- [ 7.297539@1] amlogic rfkill init
- [ 7.300580@1] not get gpio_en
- [ 7.303470@1] not get gpio_wake
- [ 7.328340@1] wifi_request_32k_clk : OFF-->ON for bt_rfkill
- [ 7.328377@1] clock_32k_pin(122) : (null)
- [ 7.332263@1] clock_32k_pin(122) : sdio_wifi
- [ 7.500020@1] UMP: UMP device driver 0000 loaded
- [ 7.500400@1] aml_hw_crypto initialization.
- [ 7.503775@1] usbcore: registered new interface driver snd-usb-audio
- [ 7.509959@1] enter rt5616_modinit
- [ 7.513068@1] dummy_codec_platform_probe
- [ 7.516978@1] == ES8323 == es8323_modinit()
- [ 7.521569@1] i2s get no clk src setting in dts, use the default mpll 0
- [ 7.527604@1] [aml-i2s-dai]enterd aml_i2s_dai_probe,old_samplerate:0,sample_rate=48000
- [ 7.535760@1] [aml-spdif-dai]enter aml_dai_spdif_init
- [ 7.540614@1] [aml-spdif-dai]enterd aml_spdif_play,set_clock:-1,sample_rate=4
- [ 7.547711@1] audio_set_958_clk, freq=4,
- [ 7.551625@1] IEC958 16bit
- [ 7.554300@1] hdmitx: audio: aout notify rate 48000
- [ 7.559159@1] hdmitx: audio: aout notify size 16
- [ 7.563747@1] hdmitx: audio: aout notify format CT_PCM
- [ 7.568869@1] hdmitx: audio: audio channel num is 1
- [ 7.573719@1] hdmitx: audio: SPDIF
- [ 7.577104@1] hdmitx: audio: current VIC: 16
- [ 7.581350@1] hdmitx: audio: audio sample rate: 3
- [ 7.586024@1] hdmitx: audio: set audio N para
- [ 7.590368@1] hdmitx: audio: PCM out to HDMI
- [ 7.594606@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 7.599292@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 7.604490@1] hdmitx: audio: Audio Type: PCM
- [ 7.608782@1] hdmitx: audio: set audio param
- [ 7.613039@1] [aml-spdif-dai]aml_spdif_probe
- [ 7.617482@1] test codec dummy_codec
- [ 7.620883@1] using external codec, index = 1
- [ 7.625205@1] using external dummy codec
- [ 7.629263@1] enter spdif_dit_probe
- [ 7.632659@1] aml_spdif_unmute
- [ 7.635979@1] codec_name = dummy_codec.0
- [ 7.639969@1] p_aml_audio->hp_disable=1
- [ 7.643496@1] falied to get spk event delay time paraments from dts file
- [ 7.650190@1] spk_event delay_time = 0
- [ 7.654982@1] aml-i2s 0:playback preallocate_dma_buffer: area=ef300000, addr=2f500000, size=524288
- [ 7.663149@1] aml-i2s 1:capture preallocate_dma_buffer: area=ef240000, addr=2f440000, size=65536
- [ 7.671605@1] aml_snd_m8 aml_m8_sound_card.5: dummy_codec <-> aml-i2s-dai.0 mapping ok
- [ 7.680813@1] aml-i2s 0:playback preallocate_dma_buffer: area=ef400000, addr=2f600000, size=524288
- [ 7.688819@1] aml-i2s 1:capture preallocate_dma_buffer: area=ef260000, addr=2f460000, size=65536
- [ 7.697253@1] aml_snd_m8 aml_m8_sound_card.5: dit-hifi <-> aml-spdif-dai.0 mapping ok
- [ 7.706198@1] -----ext_codec=1---
- [ 7.708446@1] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
- [ 7.714563@1] Netfilter messages via NETLINK v0.30.
- [ 7.719302@1] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
- [ 7.725983@1] ctnetlink v0.93: registering with nfnetlink.
- [ 7.731021@1] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
- [ 7.738065@1] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
- [ 7.744558@1] xt_time: kernel timezone is -0000
- [ 7.748638@1] ipip: IPv4 over IPv4 tunneling driver
- [ 7.753950@1] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 7.758990@1] arp_tables: (C) 2002 David S. Miller
- [ 7.763667@1] TCP: cubic registered
- [ 7.767104@1] Initializing XFRM netlink socket
- [ 7.772064@1] NET: Registered protocol family 10
- [ 7.776648@1] mip6: Mobile IPv6
- [ 7.779274@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 7.784938@1] sit: IPv6 over IPv4 tunneling driver
- [ 7.790490@1] NET: Registered protocol family 17
- [ 7.794167@1] NET: Registered protocol family 15
- [ 7.798803@1] Bridge firewalling registered
- [ 7.802968@1] Bluetooth: RFCOMM TTY layer initialized
- [ 7.807946@1] Bluetooth: RFCOMM socket layer initialized
- [ 7.813229@1] Bluetooth: RFCOMM ver 1.11
- [ 7.817120@1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- [ 7.822591@1] Bluetooth: BNEP filters: protocol multicast
- [ 7.827960@1] Bluetooth: BNEP socket layer initialized
- [ 7.833087@1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- [ 7.839149@1] Bluetooth: HIDP socket layer initialized
- [ 7.844294@1] l2tp_core: L2TP core driver, V2.0
- [ 7.848774@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
- [ 7.853699@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
- [ 7.859442@1] l2tp_netlink: L2TP netlink interface
- [ 7.864206@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
- [ 7.870278@1] l2tp_debugfs: L2TP debugfs support
- [ 7.874850@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
- [ 7.881473@1] NET: Registered protocol family 35
- [ 7.886096@1] Key type dns_resolver registered
- [ 7.891369@1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- [ 7.898278@1] Registering SWP/SWPB emulation handler
- [ 7.903196@1] enter meson_pm_init
- [ 7.906617@1] enter meson_pm_probe!
- [ 7.909974@1] meson_pm_probe done !
- [ 7.913967@1] regulator-dummy: disabling
- [ 7.917789@1] aml_rtc rtc.0: setting system clock to 2001-11-01 19:11:23 UTC (1004641883)
- [ 7.925500@1] ### dt-test ### No testcase data in device tree; not running tests
- [ 7.932930@1] meson_cpufreq: no voltage_control prop
- [ 7.937781@1] voltage_control = 0
- [ 7.942288@1] hdmitx: cec: CEC init
- [ 7.944575@2] hdmitx: cec: CEC task process
- [ 7.944724@1] input: cec_input as /devices/virtual/input/input4
- [ 7.944854@1] hdmitx: cec: hdmitx_device->cec_init_ready:0x1
- [ 7.9[ 7.978207@1] Changing uart_ao_ttyS0: baud from 0 to 115200
- [ 7.998366@1] Freeing unused kernel memory: 356K (c0b44000 - c0b9d000)
- e2fsck 1.42.12 (29-Aug-2014)
- [ 8.019443@2] aml_nftl_open ok!
- [ 8.019507@2] aml_nftl_open ok!
- Pass 1: Checking inodes, blocks, and sizes
- Pass 2: Checking directory structure
- Pass 3: Checking directory connectivity
- Pass 4: Checking reference counts
- Pass 5: Checking group summary information
- /dev/system: 1956/65536 files (1.5% non-contiguous), 252449/262144 blocks
- e2fsck 1.42.12 (29-Aug-2014)
- [ 8.170753@2] aml_nftl_open ok!
- [ 8.171708@2] aml_nftl_open ok!
- Pass 1: Checking inodes, blocks, and sizes
- Pass 2: Checking directory structure
- Pass 3: Checking directory connectivity
- Pass 4: Checking reference counts
- Pass 5: Checking group summary information
- /dev/data: 936/362160 files (8.8% non-contiguous), 151729/1447936 blocks
- [ 8.523099@0] tvmode set to 720p
- [ 8.523099@0]
- [ 8.523284@0] mode is 11,sync_duration_den=1,sync_duration_num=60
- [ 8.529380@0] TV mode 720p selected.
- [ 8.532899@0] tvoutc_setmode[489]
- [ 8.536191@0] new mode 720p
- [ 8.536191@0] set ok
- [ 8.541244@0] hdmitx: video: get current mode: 720p
- [ 8.546074@0] is_similar_hdmi_vic[325] vic_old=16,mode_new=11
- [ 8.551823@0] hdmitx: video: get current mode: 720p
- [ 8.556651@0] is_similar_hdmi_vic[325] vic_old=16,mode_new=11
- [ 8.562383@0] hdmitx: system: gate/pwr cmd: 7
- [ 8.566744@0] hdmitx: system: already init VIC = 0 Now VIC = 4
- [ 8.572626@0] hdmitx: system: 4 (cd0,cs0,pm1,vd0,1)
- [ 8.577625@0] hdmitx: system: gate/pwr cmd: 0
- [ 8.581974@0] hdmitx: system: hw reset
- [ 8.586727@0] hdmitx: audio: SPDIF
- [ 8.589131@0] hdmitx: system: reconfig packet setting done
- [ 8.728210@1] hdmitx: system: phy setting done
- [ 8.748222@1] hdmitx: system: set pll
- [ 8.748241@1] hdmitx: system: param->VIC:4
- [ 8.750317@1] mode is: 11
- [ 8.752917@1] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 8.756990@1] viu chan = 1
- [ 8.759681@1] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 8.763751@1] config HPLL
- [ 8.766352@1] set_hpll_clk_out[62] clk = 2970
- [ 8.788209@1] config HPLL done
- [ 8.788230@1] enc_vpu_bridge_reset[292]
- [ 8.928207@1] hdmitx: system: phy setting done
- [ 8.928231@1] Sink is HDMI device
- [ 8.930304@1] No sink attached
- [ 8.933370@1] hdmitx: audio: audio channel num is 1
- [ 8.938194@1] hdmitx: audio: SPDIF
- [ 8.941582@1] hdmitx: audio: current VIC: 4
- [ 8.945731@1] hdmitx: audio: audio sample rate: 3
- [ 8.950416@1] hdmitx: audio: set audio N para
- [ 8.954750@1] hdmitx: audio: PCM out to HDMI
- [ 8.958998@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 8.963674@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 8.968881@1] hdmitx: audio: Audio Type: PCM
- [ 8.973786@1] set_vout_mode[249]
- [ 9.055925@1] vfm_map_store:rm default
- [ 9.055925@1]
- [ 9.056000@1] vfm_map_store:add default decoder ppmgr deinterlace amvideo
- [ 9.056000@1]
- [H[J[H[J[ 9.073484@0] aml_nftl_open ok!
- [ 9.073695@0] blktrans_ioctl -cmd: 5331,801c0204,64
- [ 9.102064@0] aml_nftl_open ok!
- [ 9.102259@0] blktrans_ioctl -cmd: 5331,801c0204,64
- [ 9.104275@2] aml_nftl_open ok!
- [ 9.104314@2] aml_nftl_open ok!
- [ 9.138307@2] aml_nftl_open ok!
- [ 9.138370@2] aml_nftl_open ok!
- [ 9.153920@0] aml_nftl_open ok!
- [ 9.154652@0] EXT3-fs (system): error: couldn't mount because of unsupported optional features (40)
- [ 9.160554@0] aml_nftl_open ok!
- [ 9.163629@0] EXT2-fs (system): error: couldn't mount because of unsupported optional features (40)
- [ 9.172646@0] aml_nftl_open ok!
- [ 9.175762@0] force enable DISCARD here for ext4 fs
- [ 9.182266@0] checked enable EXT4 DISCARD here
- [ 9.184972@0] EXT4-fs (system): mounted filesystem with ordered data mode. Opts: (null)
- [ 9.280203@0] aml_nftl_open ok!
- [ 9.280954@0] EXT3-fs (data): error: couldn't mount because of unsupported optional features (40)
- [ 9.286620@0] aml_nftl_open ok!
- [ 9.289772@0] EXT2-fs (data): error: couldn't mount because of unsupported optional features (40)
- [ 9.298596@0] aml_nftl_open ok!
- [ 9.301692@0] force enable DISCARD here for ext4 fs
- [ 9.308899@0] checked enable EXT4 DISCARD here
- [ 9.310910@0] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: (null)
- [ 13.712869@0] systemd[1]: systemd 217 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK -SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN )
- [ 13.725769@0] systemd[1]: Detected architecture 'arm'.
- [ 13.7
- Welcome to [1mOpenELEC (unofficial) - Version: devel-20150926153716-r20783-g553f562[0m!
- [ 13.765762@0] systemd[1]: Failed to insert module 'autofs4'
- [ 13.766222@0] systemd[1]: Set hostname to <OpenELEC>.
- [ 13.770868@0] systemd[1]: Initializing machine ID from random generator.
- [ 13.779831@0] systemd[1]: Populated /etc with preset unit settings.
- [ [[32m OK [0m] Created slice Root Slice.
- [ 13.828316@3] systemd[1]: Created slice RooT[32m OK [0m] Created slice System Slice.
- [ 13.848251@3] systemd[1]: Created slice System` Starting Factory reset...
- [[32m OK [0m] Started Factory reset.
- [ 13.888278@0] systemd[1]: Started Factory reset[[32m OK [0m] Reached target Factory reset target.
- [ 17[ 13.909740@0] systemd[1]: Startup finished in 13.606s (kernel) + 205ms (userspace) = 13.811s.
- [ 13.974651@0] systemd[1]: Starting Kodi reboot script...
- [ 13.975552@0] systemd[1]: Unmounting /storage...
- [ 13.980211@0] systemd[1]: Unmounting /flash...
- Starting Kod[ 13.985768@0] systemd[1]: Stopping Factory reset target.
- i reboot script...
- [ 13.992889@0] systemd[1]: Stopped target Factory reset target.
- [ 13.999990@0] systemd[1]: Starting Shutdown.
- [ 14.003038@0] systemd[1]: Reached target Shutdown.
- [ 14.003112@3] aml_nftl_open ok!
- [ 14.003124@3] blktrans_ioctl -cmd: 4c01,801c0204,64
- [ 14.015928@2] aml_nftl_open ok!
- [ 14.017377@0] systemd[1]: Started Kodi reboot script.
- [ 14.017795@0] systemd[1]: Unmounted /storage.
- [ 14.028287@2] blktrans_ioctl -cmd: 4c01,801c0204,64
- [ 14.033846@0] systemd[1]: Unmounted /flash.
- Unmounting /storage...
- [ 14.040575@0] systemd[1]: Starting Unmount All Filesystems.
- [ 14.045695@0] systemd[1]: Reached target Unmount All Filesystems.
- [ 14.052427@0] systemd[1]: Starting Final Step.
- [ 14.056177@0] systemd[1]: Reached target Final Step.
- [ 14.061198@0] systemd[1]: Starting Reboot...
- Unmounting /flash...
- [[32m OK [0m] Stopped target Factory[ 14.073170@0] systemd[1]: Shutting down.
- reset target.
- [[32m OK [0m] Reached target Shutdown.
- [ 14.092886@1] systemd-shutdown[1]: Sending SIGTERM to remaining processes...
- [ 14.103368@1] systemd-shutdown[1]: Sending SIGKILL to remaining processes...
- [ 14.112777@1] systemd-shutdown[1]: Unmounting file systems.
- [ 14.113456@1] systemd-shutdown[1]: All filesystems unmounted.
- [ 14.118465@1] systemd-shutdown[1]: Deactivating swaps.
- [ 14.123634@1] systemd-shutdown[1]: All swaps deactivated.
- [ 14.128972@1] systemd-shutdown[1]: Detaching loop devices.
- [ 14.135112@1] systemd-shutdown[1]: Not all loop devices detached, 1 left.
- [ 14.141460@1] systemd-shutdown[1]: Detaching DM devices.
- [ 14.146618@1] systemd-shutdown[1]: All DM devices detached.
- [ 14.151996@1] systemd-shutdown[1]: Cannot finalize remaining loop devices, continuing.
- [ 14.160338@1] systemd-shutdown[1]: Failed to finalize loop devices, ignoring
- [ 14.167050@1] systemd-shutdown[1]: Rebooting.
- [ 14.171322@1] aml_keys_notify_reboot:1717
- [ 14.197884@0] sd 0:0:0:0: Driver sd calling sd_shutdown shutdown
- [ 14.198660@0] rn5t618_pmu rn5t618_pmu.0: Driver rn5t618_pmu calling platform_drv_shutdown shutdown
- [ 14.207369@0] ricoh_pmu 0-0032: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.214399@0] i2c i2c-3: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.220837@0] i2c i2c-2: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.227208@0] i2c i2c-1: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.233645@0] i2c i2c-0: Bus i2c calling i2c_device_shutdown shutdown
- [ 14.240073@0] amlnfdev nand: Driver amlnfdev calling platform_drv_shutdown shutdown
- [ 14.247663@0] boot_device_flag : 0
- [ 14.251104@0] aml_rtc rtc.0: Driver aml_rtc calling platform_drv_shutdown shutdown
- [ 14.259229@0] Restarting system.
- [ 14.261783@0]
- [ 14.263429@0] Restarting Linux version 3.10.86 (user@Debian) (gcc version 4.9.2 (GCC) ) #1 SMP PREEMPT Fri Sep 25 21:24:05 MSK 2015
- [ 14.263429@0]
- [ j
- TE : 33257
- BT : 19:49:35 Jul 29 2015
- PMU:rn5t618
- DC01 v:1100, 0x[36]: 28 -> 28
- DC02 v:1150, 0x[37]: 2c -> 2c
- DC03 v:1500, 0x[38]: 48 -> 48
- LDO01 v:2900, 0x[4c]: 50 -> 50
- LDO02 v:1800, 0x[4d]: 24 -> 24
- LDO03 v:1800, 0x[4e]: 30 -> 30
- LDO04 v:2850, 0x[4f]: 4e -> 4e
- LDO05 v:1800, 0x[50]: 24 -> 24
- LDO0a v:2700, 0x[56]: 28 -> 28
- LDO0b v:900, 0x[57]: 00 -> 00
- CPU clock is 1200MHz
- CPU type: M8
- DDR info: 2GB(auto) @ 792MHz(1T)
- DDR channel: DDR 0 + DDR 1
- DDR init use : 12086 us
- HHH
- Boot From SPI
- ucl decompress...pass
- 0x12345678
- Boot from internal device 1st SPI
- TE : 397582
- System Started
- U-boot-00000-gd05fbcd-dirty(m8_k200_v1@dualboot) (Jul 29 2015 - 19:49:24)
- clr h-ram
- DRAM: 2 GiB
- relocation Offset is: 6fec0000
- show partition table:
- part: 0, name : logo, size : 2000000
- part: 1, name : recovery, size : 2000000
- part: 2, name : misc, size : 1000000
- part: 3, name : boot, size : 1000000
- part: 4, name : linuxk, size : 1000000
- part: 5, name : system, size : 40000000
- part: 6, name : cache, size : 20000000
- part: 7, name : data, size : end
- aml_card_type=0x100
- MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
- [mmc_register] add mmc dev_num=1, port=2, if_type=6
- SDIO Port B: 0, SDIO Port C: 1
- PMU fault status:
- reg[0x9A] = 0x0d
- LSI version:04, OTP version:0c
- PMU type:RN5T618
- register usb cfg[0][1] = 7ff6fdd4
- register usb cfg[2][0] = 7ff7331c
- NAND: SPI BOOT: boot_device_flag 0
- Nand PHY driver Version: 1.01.001.0004 (c) 2013 Amlogic Inc.
- amlnf_phy_init : amlnf init flag 0
- NAND device id: ad de 94 da 74 c4 ad de
- detect NAND device: A revision 20nm NAND 8GiB H27UCG8T2A
- nand chip ce mask 1
- AML_NAND_NEW_OOB : new oob
- bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
- hynix nand get default reg value at blk:8, page:2048
- NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 0
- NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
- NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 54
- i=0,register --- nand_key
- nfcache : offset: 0x000006000000 -0x000024800000 : partitons 1 : single_chip multi_plane
- nfcode : offset: 0x00002a800000 -0x00004f800000 : partitons 6 : single_chip multi_plane
- nfdata : offset: 0x00007a000000 -0x000186000000 : partitons 1 : single_chip multi_plane
- bad block count = 0
- bad block count = 0
- bad block count = 0
- amlnf_logic_init: START
- amlnf_logic_init: COMPLETE
- get_boot_device_flag: init_ret 0
- get_boot_device_flag SPI BOOT:
- nand init success, change the device_boot_flag to 4 : spi+nand
- SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
- SF: Detected MX25L1605D with page size 256, total 2 MiB
- SPI NOR Flash have write protect!!!
- set_storage_device_flag: store 4
- vpu driver detect cpu type: m8
- vpu clk_level in dts: 7
- set vpu clk: 364300000Hz, readback: 364300000Hz(0x700)
- Net: Meson_Ethernet
- init suspend firmware done. (ret:0)
- cvbs trimming.1.v5: 0xa0, 0x0
- normal
- start normal
- wipe_data=successful
- wipe_cache=successful
- reboot_mode=normal
- mode = 8 vic = 16
- set HDMI vic: 16
- config HPLL
- config HPLL done
- reconfig packet setting done
- Hit Enter key to stop autoboot -- : 1 0
- exit abortboot: 0
- current storer:nand_key
- key save is auto select storer(nand or emmc)
- write key code version3_flush:708,prov->write:7fee8dd8
- size:4096
- arg_pages:1
- extra_page:0
- write key ok!!
- Booting...
- mac is: :00:01:db:88:06:e4
- ## ANDROID Format IMAGE
- ## Booting kernel from Legacy Image at 12000000 ...
- Image Name: Linux-3.10.86
- Image Type: ARM Linux Kernel Image (lzo compressed)
- Data Size: 6658024 Bytes = 6.3 MiB
- Load Address: 00208000
- Entry Point: 00208000
- Verifying Checksum ... OK
- Ramdisk start addr = 0x1265a800, len = 0x31d600
- Flat device tree start addr = 0x12978000, len = 0x47b4 magic=0xedfe0dd0
- Uncompressing Kernel Image ... OK
- uboot time: 2238414 us.
- EFUSE machid is not set.
- Using machid 0xf81 from environment
- From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x5326001
- Loading Ramdisk to 05008000, end 05325600 ... OK
- Loading Device Tree to 05000000, end 050077b3 ... OK
- Starting kernel ...
- [ 0.000000@0] Booting Linux on physical CPU 0x200
- [ 0.000000@0] Linux version 3.10.86 (user@Debian) (gcc version 4.9.2 (GCC) ) #1 SMP PREEMPT Fri Sep 25 21:24:05 MSK 2015
- [ 0.000000@0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
- [ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
- [ 0.000000@0] Machine: Amlogic Meson8, model: AMLOGIC
- [ 0.000000@0] physical memory start address is 0x200000
- [ 0.000000@0] reserved_end is 1f1fffff
- [ 0.000000@0]
- [ 0.000000@0] Total memory is 2046 MiB
- [ 0.000000@0] Reserved low memory from 0x06000000 to 0x1f1fffff, size: 402 MiB
- [ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x0a900000 ( 72 MiB)
- [ 0.000000@0] mesonfb1(low) : 0x0a900000 - 0x0aa00000 ( 1 MiB)
- [ 0.000000@0] deinterlace0(high) : 0x7df00000 - 0x80000000 ( 33 MiB)
- [ 0.000000@0] mesonstream0(low) : 0x0aa00000 - 0x0ca00000 ( 32 MiB)
- [ 0.000000@0] vdec0(low) : 0x0ca00000 - 0x1ca00000 (256 MiB)
- [ 0.000000@0] ppmgr0(high) : 0x7cf00000 - 0x7df00000 ( 16 MiB)
- [ 0.000000@0] vdin10(low) : 0x1ca00000 - 0x1da00000 ( 16 MiB)
- [ 0.000000@0] amlvideo20(low) : 0x1da00000 - 0x1f200000 ( 24 MiB)
- [ 0.000000@0] get storage device: storage 4
- [ 0.000000@0] value=4
- [ 0.000000@0] get_storage_device : get storage device: storage 4
- [ 0.000000@0] get_storage_device : value=4
- [ 0.000000@0] [get_storage_device] storage_flag=4
- [ 0.000000@0] [get_storage_device] the storage device does NOT relate to eMMC, storage_flag=4
- [ 0.000000@0] cma: CMA: reserved 8 MiB at 2f000000
- [ 0.000000@0] cma: Found region@0, memory base 0, size 18 MiB
- [ 0.000000@0] cma: CMA: reserved 20 MiB at 2dc00000
- [ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
- [ 0.000000@0] Meson chip version = RevC (19:C - 0:27ED)
- [ 0.000000@0] PERCPU: Embedded 8 pages/cpu @c1e72000 s12288 r8192 d12288 u32768
- [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 403216
- [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200n8 no_console_suspend storage=4 cvbsdrv=0 vdaccfg=0xa000 reboot_args=uboot_suspend logo=osd1,loaded,0x15100000,1080p,full hdmimode=1080p cvbsmode=576cvbs androidboot.firstboot=0 hdmitx= mac=00:01:db:88:06:e4 hdmitx=cecf boot=/dev/system disk=/dev/data BOOT_IMAGE=/dev/linuxk scaling_governor=ondemand scaling_min_freq=96000 scaling_max_freq=1608000 ssh
- [ 0.000000@0] cvbs performance line = 0
- [ 0.000000@0] cvbs trimming line = 0xa000
- [ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0
- [ 0.000000@0] osd1:1
- [ 0.000000@0] loaded:268435459
- [ 0.000000@0] logo has been loaded
- [ 0.000000@0] 1080p:15
- [ 0.000000@0] full:2
- [ 0.000000@0] kernel get hdmimode form uboot is 1080p
- [ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs
- [ 0.000000@0] ******** uboot setup mac-addr: 0:1:db:88:6:e4
- [ 0.000000@0] hdmitx: cec: Function List: enable, one touch play, one touch standby, auto power by tv
- [ 0.000000@0] hdmitx: cec: HDMI aml_read_reg32(P_AO_DEBUG_REG0):0xf
- [ 0.000000@0] hdmitx: cec: HDMI hdmi_cec_func_config:0xf
- [ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [ 0.000000@0] Memory: 64MB 16MB 1501MB = 1581MB total
- [ 0.000000@0] Memory: 1555264k/1555264k available, 63680k reserved, 1266688K highmem
- [ 0.000000@0] Virtual kernel memory layout:
- [ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
- [ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
- [ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
- [ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
- [ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
- [ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
- [ 0.000000@0] .text : 0xc0008000 - 0xc0b437ac (11502 kB)
- [ 0.000000@0] .init : 0xc0b44000 - 0xc0b9d000 ( 356 kB)
- [ 0.000000@0] .data : 0xc0b9e000 - 0xc0c4d610 ( 702 kB)
- [ 0.000000@0] .bss : 0xc0c4d610 - 0xc0ebfbac (2506 kB)
- [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000@0] Preemptible hierarchical RCU implementation.
- [ 0.000000@0] NR_IRQS:256
- [ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
- [ 0.000000@0] Switching to timer-based delay loop
- [ 0.000000@0] Console: colour dummy device 80x30
- [ 0.000000@0] console [ttyS0] enabled
- [ 0.403804@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
- [ 0.414100@0] pid_max: default: 32768 minimum: 301
- [ 0.418968@0] Security Framework initialized
- [ 0.423196@0] Mount-cache hash table entries: 512
- [ 0.430906@0] CPU: Testing write buffer coherency: ok
- [ 0.433105@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
- [ 0.438659@0] Setting up static identity map for 0xc07e0990 - 0xc07e09e8
- [ 0.445444@0] L310 cache controller enabled
- [ 0.449465@0] l2x0: 8 ways, 4096 sets, CACHE_ID 0x4100a0c9, Cache size: 1048576 B
- [ 0.457035@0] AUX_CTRL 0x7ec80001, PERFETCH_CTRL 0x71000007, POWER_CTRL 0x00000000
- [ 0.465158@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222
- [ 0.550140@0] write pen_release: 1
- [ 0.550344@1] CPU1: Booted secondary processor
- [ 0.550357@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
- [ 0.570131@0] write pen_release: 2
- [ 0.578273@2] CPU2: Booted secondary processor
- [ 0.578285@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
- [ 0.590128@0] write pen_release: 3
- [ 0.598268@3] CPU3: Booted secondary processor
- [ 0.598281@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
- [ 0.598346@0] Brought up 4 CPUs
- [ 0.611479@0] SMP: Total of 4 processors activated (8.00 BogoMIPS).
- [ 0.617709@0] CPU: All CPU(s) started in SVC mode.
- [ 0.622931@0] devtmpfs: initialized
- [ 0.631257@0] clkrate [ xtal ] : 24000000
- [ 0.631286@0] clkrate [ pll_sys ] : 1200000000
- [ 0.634527@0] clkrate [ pll_fixed ] : 2550000000
- [ 0.639207@0] clkrate [ pll_vid ] : 366000000
- [ 0.643634@0] TODO: clk_get_rate_hpll() is not implement in M8 now
- [ 0.649781@0] clkrate [ pll_hpll ] : 0
- [ 0.653600@0] clkrate [ pll_ddr ] : 0
- [ 0.657324@0] clkrate [ a9_clk ] : 1200000000
- [ 0.661750@0] clkrate [ clk81 ] : 141666666
- [ 0.667021@0] pinctrl core: initialized pinctrl subsystem
- [ 0.671689@0] regulator-dummy: no parameters
- [ 0.676482@0] NET: Registered protocol family 16
- [ 0.686564@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations
- [ 0.690196@0] VPU driver version: v03
- [ 0.691698@0] vpu driver detect cpu type: m8
- [ 0.695946@0] load vpu_clk in dts: 364300000Hz(7)
- [ 0.700694@0] vpu_probe OK
- [ 0.703782@0] cma: Assigned CMA region with name cma_0 to amvenc_avc.0 device
- [ 0.714486@0] amlogic_gpio gpio: Probed amlogic GPIO driver
- [ 0.716176@0] register lm device lm-root
- [ 0.719952@0] register lm device lm1
- [ 0.723514@0] register lm device lm0
- [ 0.727196@0] Init pinux probe!
- [ 0.730493@0] pinmux-m8 pinmux: Probed amlogic pinctrl driver
- [ 0.735888@0] tv_init_module
- [ 0.738684@0] major number 254 for disp
- [ 0.742504@0] vout_register_server
- [ 0.745874@0] register tv module server ok
- [ 0.750026@0] major number 0 for disp
- [ 0.753675@0] register tv module server ok
- [ 0.757982@0] video2_early_init enter
- [ 0.761571@0] video2_early_init exit
- [ 0.765145@0] aml_i2c version: 20140813
- [ 0.769117@0] aml-i2c i2c-AO: add adapter aml_i2c_adap0(ed80e0a8)
- [ 0.775014@0] aml-i2c i2c-AO: aml i2c bus driver.
- [ 0.779867@0] aml-i2c i2c-A: add adapter aml_i2c_adap1(ed80d4a8)
- [ 0.785672@0] aml-i2c i2c-A: aml i2c bus driver.
- [ 0.790469@0] aml-i2c i2c-B: add adapter aml_i2c_adap2(ed80c8a8)
- [ 0.796238@0] aml-i2c i2c-B: aml i2c bus driver.
- [ 0.801030@0] aml-i2c i2c-C: add adapter aml_i2c_adap3(ed80dca8)
- [ 0.806813@0] aml-i2c i2c-C: aml i2c bus driver.
- [ 0.811571@0] aml_pmu_init, 454
- [ 0.814596@0] call aml_dvfs_init in
- [ 0.818246@0] hdmitx: system: amhdmitx_init
- [ 0.822164@0] hdmitx: system: Ver: 2014May6
- [ 0.826381@0] hdmitx: system: amhdmitx_probe
- [ 0.830802@0] hdmitx: system: not find cec config
- [ 0.835243@0] hdmitx: system: not find vend_init_data
- [ 0.840515@0] hdmitx: system: gate/pwr cmd: 7
- [ 0.844607@0] hdmitx: system: ALREADY init VIC = 16
- [ 0.849459@0] hdmitx: system: gate/pwr cmd: 0
- [ 0.854183@1] hdmitx: system: reset intr mask
- [ 0.870401@0] hdmitx: system: irq 1
- [ 0.922016@0] bio: create slab <bio-0> at 0
- [ 0.922774@0] SCSI subsystem initialized
- [ 0.924822@0] usbcore: registered new interface driver usbfs
- [ 0.930199@0] usbcore: registered new interface driver hub
- [ 0.935685@0] usbcore: registered new device driver usb
- [ 0.940903@0] Linux video capture interface: v2.00
- [ 0.945754@0] pps_core: LinuxPPS API ver. 1 registered
- [ 0.950656@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.959976@0] PTP clock support registered
- [ 0.964675@0] mode is 15,sync_duration_den=1,sync_duration_num=60
- [ 0.970078@0] TV mode 1080p selected.
- [ 0.973706@0] already display in uboot
- [ 0.979505@0] call aml_pmu_probe_init in
- [ 0.981390@0] aml_pmus_probe, child name:rn5t618
- [ 0.985924@0] aml_pmus_probe, i2c_bus:i2c_bus_ao
- [ 0.990727@1] hdmitx: system: gate/pwr cmd: 4
- [ 0.990882@0] [RICOH]setup_supply_data, failed to get property: board_battery
- [ 0.991789@0] Allocate new i2c device: adapter:0, addr:0x32, node name:rn5t618, type:ricoh_pmu
- [ 0.992183@0] Advanced Linux Sound Architecture Driver Initialized.
- [ 0.992652@0] Bluetooth: Core ver 2.16
- [ 0.992728@0] NET: Registered protocol family 31
- [ 0.992730@0] Bluetooth: HCI device and connection manager initialized
- [ 0.992738@0] Bluetooth: HCI socket layer initialized
- [ 0.992743@0] Bluetooth: L2CAP socket layer initialized
- [ 0.992756@0] Bluetooth: SCO socket layer initialized
- [ 0.993002@0] cfg80211: Calling CRDA to update world regulatory domain
- [ 1.054422@0] Switching to clocksource Timer-E
- [ 1.078108@0] NET: Registered protocol family 2
- [ 1.078592@0] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.084239@0] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
- [ 1.090846@0] TCP: Hash tables configured (established 4096 bind 4096)
- [ 1.097321@0] TCP: reno registered
- [ 1.100681@0] UDP hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.106662@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
- [ 1.113200@0] NET: Registered protocol family 1
- [ 1.117752@0] RPC: Registered named UNIX socket transport module.
- [ 1.123651@0] RPC: Registered udp transport module.
- [ 1.128496@0] RPC: Registered tcp transport module.
- [ 1.133345@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 1.140004@0] wifi_dev_probe
- [ 1.142795@0] wifi_dt : interrupt_pin=GPIOX_21
- [ 1.147218@0] wifi_dt : irq_num=null
- [ 1.150779@0] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH
- [ 1.155887@0] wifi_dt : power_on_pin=GPIOAO_6
- [ 1.160241@0] wifi_dt : power_on_pin2=GPIOX_11
- [ 1.164641@0] interrupt_pin=133, irq_num=4, irq_trigger_type=0, power_on_pin=6,clock_32k_pin=122
- [ 1.173577@0] Unpacking initramfs...
- [ 1.184791@0] Freeing initrd memory: 3188K (c4e08000 - c5125000)
- [ 1.187048@0] audit: initializing netlink socket (disabled)
- [ 1.190756@0] type=2000 audit(1.090:1): initialized
- [ 1.195999@0] bounce pool size: 64 pages
- [ 1.204598@0] VFS: Disk quotas dquot_6.5.2
- [ 1.204831@0] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [ 1.211882@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 1.217327@0] NFS: Registering the id_resolver key type
- [ 1.221465@0] Key type id_resolver registered
- [ 1.225729@0] Key type id_legacy registered
- [ 1.230300@0] fuse init (API version 7.22)
- [ 1.234501@0] msgmni has been set to 625
- [ 1.238886@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
- [ 1.245407@0] io scheduler noop registered
- [ 1.249514@0] io scheduler deadline registered
- [ 1.254054@0] io scheduler cfq registered (default)
- [ 1.258149@1] hdmitx: system: gate/pwr cmd: 5
- [ 1.258151@1] hdmitx: edid: edid ready
- [ 1.258152@1] hdmitx: system: gate/pwr cmd: 4
- [ 1.274450@0] loop: module loaded
- [ 1.275181@0] tun: Universal TUN/TAP device driver, 1.6
- [ 1.279658@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- [ 1.286124@0] PPP generic driver version 2.4.2
- [ 1.290599@0] PPP BSD Compression module registered
- [ 1.295247@0] PPP Deflate Compression module registered
- [ 1.300465@0] PPP MPPE Compression module registered
- [ 1.305395@0] NET: Registered protocol family 24
- [ 1.310104@0] usbcore: registered new interface driver asix
- [ 1.315643@0] usbcore: registered new interface driver ax88179_178a
- [ 1.321872@0] usbcore: registered new interface driver cdc_ether
- [ 1.327854@0] usbcore: registered new interface driver dm9601
- [ 1.333550@0] usbcore: registered new interface driver net1080
- [ 1.339378@0] usbcore: registered new interface driver cdc_subset
- [ 1.345425@0] usbcore: registered new interface driver zaurus
- [ 1.351174@0] usbcore: registered new interface driver cdc_ncm
- [ 1.357260@0] usbcore: registered new interface driver usb-storage
- [ 1.363322@0] mousedev: PS/2 mouse device common for all mice
- [ 1.368874@0] i2c /dev entries driver
- [ 1.373131@0] lirc_dev: IR Remote Control driver registered, major 246
- [ 1.378992@0] IR NEC protocol handler initialized
- [ 1.383663@0] IR RC5(x) protocol handler initialized
- [ 1.388614@0] IR RC6 protocol handler initialized
- [ 1.393284@0] IR JVC protocol handler initialized
- [ 1.397972@0] IR Sony protocol handler initialized
- [ 1.402733@0] IR RC5 (streamzap) protocol handler initialized
- [ 1.408462@0] IR SANYO protocol handler initialized
- [ 1.413308@0] IR MCE Keyboard/mouse protocol handler initialized
- [ 1.419295@0] IR LIRC bridge handler initialized
- [ 1.423983@0] usbcore: registered new interface driver uvcvideo
- [ 1.429787@0] USB Video Class driver (1.1.1)
- [ 1.434313@0] device-mapper: uevent: version 1.0.3
- [ 1.439096@0] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
- [ 1.447578@0] Bluetooth: HCI UART driver ver 2.2
- [ 1.451981@0] Bluetooth: HCI H4 protocol initialized
- [ 1.457248@0] hidraw: raw HID events driver (C) Jiri Kosina
- [ 1.467604@0] usbcore: registered new interface driver usbhid
- [ 1.468138@1] hdmitx: system: gate/pwr cmd: 5
- [ 1.468139@1] hdmitx: edid: edid ready
- [ 1.468144@1] hdmitx: edid: check sum valid
- [ 1.468146@1] hdmitx: edid: check sum valid
- [ 1.468148@1] hdmitx: edid: blk0 raw data
- [ 1.468170@1] 00ffffffffffff00410c00000101010104180103804024780af9aba2554a9a25
- [ 1.468192@1] 0f474a2108008180010101010101010101010101010104740030f2705a80b058
- [ 1.468211@1] 8a0080682100001e023a801871382d40582c450080682100001e000000fc0050
- [ 1.468231@1] 48494c495053204654560a20000000fd00184c1e531e000a2020202020200132
- [ 1.468232@1]
- [ 1.468233@1] hdmitx: edid: blk1 raw data
- [ 1.468253@1] 02033c714d1f102021140513041102150601290907031507503d07c083010000
- [ 1.468272@1] 7b030c002000003c20c86e020103014100fc20306070281038106810023a80d0
- [ 1.468292@1] 72382d40102c458080682100001e011d803e73382d407e2c458080682100001e
- [ 1.468311@1] 011d80d0721c1620102c258080682100009e000000000000000000000000005b
- [ 1.468312@1]
- [ 1.468348@1] hdmitx: edid: find IEEEOUT
- [ 1.468389@1] hdmitx: video: get current mode: 1080p
- [ 1.468397@1] is_similar_hdmi_vic[325] vic_old=16,mode_new=15
- [ 1.468400@1] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
- [ 1.468403@1] hdmitx: audio: audio channel num is 0
- [ 1.468408@1] hdmitx: audio: SPDIF
- [ 1.468419@1] hdmitx: audio: current VIC: 16
- [ 1.468420@1] hdmitx: audio: audio sample rate: 0
- [ 1.468422@1] hdmitx: audio: set audio N para
- [ 1.468429@1] hdmitx: audio: PCM out to HDMI
- [ 1.489031@1] hdmitx: audio: Time out: AIU_HDMI_CLK_DATA_CTRL
- [ 1.489034@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 1.489035@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 1.489090@1] hdmitx: cec: CEC not ready
- [ 1.619894@0] usbhid: USB HID core driver
- [ 1.624278@0] zram: Created 1 device(s) ...
- [ 1.628399@0] ashmem: initialized
- [ 1.631468@0] logger: created 256K log 'log_main'
- [ 1.636152@0] logger: created 256K log 'log_events'
- [ 1.641029@0] logger: created 256K log 'log_radio'
- [ 1.645765@0] logger: created 256K log 'log_system'
- [ 1.650775@0] vout_init_module
- [ 1.653551@0] start init vout module
- [ 1.657314@0] create vout attribute ok
- [ 1.661729@0] ge2d_init
- [ 1.663652@0] ge2d_dev major:243
- [ 1.667149@0] ge2d start monitor
- [ 1.670282@0] osd_init
- [ 1.670286@1] ge2d workqueue monitor start
- [ 1.676768@0] osd_probe, vinfo:c083630c
- [ 1.681061@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=73728K
- [ 1.688713@0] osd_probe, mydef_var:c0bfb0e0, vinfo:c083630c
- [ 1.694248@0] init fbdev bpp is :32
- [ 1.697800@0] ---------------clear framebuffer0 memory
- [ 1.761533@0] Console: switching to colour frame buffer device 240x67
- [ 1.788054@0] Frame buffer memory assigned at phy:0x0a900000, vir:0xf0200000, size=1024K
- [ 1.793858@0] osd_probe, mydef_var:c0bfb0e0, vinfo:c083630c
- [ 1.799414@0] don't find to display_size_default from mesonfb-dts
- [ 1.805476@0] init fbdev bpp is :16
- [ 1.821316@0] osd probe ok
- [ 1.821476@0] osd_ext_init
- [ 1.821862@0] vout2_init_module enter
- [ 1.831139@0] amlvideo-000: V4L2 device registered as video10
- [ 1.831440@0] amlvideo2: V4L2 device registered as video11
- [ 1.837006@0] ionvideo-000: V4L2 device registered as video13
- [ 1.842441@0] Video Technology Magazine Ion Video Capture Board ver 1.0 successfully loaded.
- [ 1.851255@0] aml_wdt_driver_init,301
- [ 1.854473@0] ** disable watchdog
- [ 1.857987@0] keys===========================================
- [ 1.863489@0] keys_devno=f000000
- [ 1.866879@0] securitykey: device aml_keys created
- [ 1.871498@0] amlkeys=0
- [ 1.873963@0] platform_driver_register--aml_keys_driver--------------------
- [ 1.880913@0] key unify config unifykey-num is 6
- [ 1.885443@0] key unify fact unifykey-num is 6
- [ 1.889869@0] aml_unifykeys_probe:694=============unifykey_devno:ef00000
- [ 1.896698@0] unifykey: device unifykeys created ok
- [ 1.901461@0] platform_driver_register--unifykey management driver--------------------
- [ 1.909630@0] set uart_ao pinmux use pinctrl subsystem
- [ 1.914457@0] P_AO_RTI_PIN_MUX_REG:78005861
- [ 1.918670@0] start uart_ao_ttyS0:(irq = 122)
- [ 1.922956@0] register uart_ao ok
- [ 1.926447@0] set uart_a pinmux use pinctrl subsystem
- [ 1.931298@0] P_AO_RTI_PIN_MUX_REG:78005861
- [ 1.935445@0] start uart_a_ttyS1:(irq = 58)
- [ 1.939618@0] register uart_a ok
- [ 1.942987@0] start uart_d_ttyS4:(irq = 126)
- [ 1.947050@0] register uart_d ok
- [ 1.950416@0] dwc_otg: version 3.10a 12-MAY-2014
- [ 1.954883@0] dwc_otg_driver_probe NOT match
- [ 1.959154@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000
- [ 1.967688@0] USB (1) use clock source: XTAL input
- [ 1.993512@0] Core Release: 3.10a
- [ 1.993537@0] Setting default values for core params
- [ 1.996135@0] curmode: 1, host_only: 1
- [ 2.020009@0] Using Buffer DMA mode
- [ 2.020034@0] OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 2.022369@0] Working on port type = HOST
- [ 2.027048@0] dwc_otg lm1: DWC OTG Controller
- [ 2.030736@0] dwc_otg lm1: new USB bus registered, assigned bus number 1
- [ 2.037378@0] dwc_otg lm1: irq 63, io mem 0x00000000
- [ 2.042329@0] -------hcd->flags.d32 = 0
- [ 2.046133@0] Init: Port Power? op_state=1
- [ 2.050208@0] Init1: Power Port (0)
- [ 2.053742@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.060621@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.067979@0] usb usb1: Product: DWC OTG Controller
- [ 2.072819@0] usb usb1: Manufacturer: Linux 3.10.86 dwc_otg_hcd
- [ 2.078729@0] usb usb1: SerialNumber: lm1
- [ 2.083066@0] hub 1-0:1.0: USB hub found
- [ 2.086605@0] hub 1-0:1.0: 1 port detected
- [ 2.090872@0] usb0: type: 0, speed: 0, config: 0, dma: 0, id: 0, phy: fe108800, ctrl: fe040000
- [ 2.099287@0] USB (0) use clock source: XTAL input
- [ 2.125067@0] Core Release: 3.10a
- [ 2.125092@0] Setting default values for core params
- [ 2.127686@0] curmode: 1, host_only: 0
- [ 2.191518@0] Using Buffer DMA mode
- [ 2.191543@0] OTG VER PARAM: 1, OTG VER FLAG: 1
- [ 2.193874@0] Working on port type = OTG
- [ 2.197774@0] Current port type: SLAVE
- [ 2.201627@0] dwc_otg lm0: DWC OTG Controller
- [ 2.205859@0] dwc_otg lm0: new USB bus registered, assigned bus number 2
- [ 2.212548@0] dwc_otg lm0: irq 62, io mem 0x00000000
- [ 2.217484@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
- [ 2.224414@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- [ 2.231774@0] usb usb2: Product: DWC OTG Controller
- [ 2.236610@0] usb usb2: Manufacturer: Linux 3.10.86 dwc_otg_hcd
- [ 2.242525@0] usb usb2: SerialNumber: lm0
- [ 2.246844@0] hub 2-0:1.0: USB hub found
- [ 2.250425@0] hub 2-0:1.0: 1 port detected
- [ 2.254577@0] Dedicated Tx FIFOs mode
- [ 2.258348@0] using timer detect id change, ed913800
- [ 2.263199@0] boot_device_flag : 0
- [ 2.266427@0] ===========================================amlnf_init:642,nand device tree ok,dev-name:nand
- [ 2.275966@0] Nand PHY driver Version: 2.01.001.0006 (c) 2013 Amlogic Inc.
- [ 2.281680@3] HOST mode
- [ 2.285258@0] amlnf_phy_init : amlnf init flag 0
- [ 2.289883@1] Indeed it is in host mode hprt0 = 00021501
- [ 2.289929@0] ######STS IRQ mode for nand driver
- [ 2.289981@0] NAND device id: ad de 94 da 74 c4 ad de
- [ 2.289986@0] detect NAND device: A revision 20nm NAND 8GiB H27UCG8T2A
- [ 2.307835@3] -------hcd->flags.d32 = 0
- [ 2.307859@3] Init: Port Power? op_state=1
- [ 2.307861@3] Init1: Power Port (0)
- [ 2.307866@3] [RN5T618]rn5t618_otg_change, driver is not ready, do it later
- [ 2.307868@3] set usb port power on (board gpio 15)!
- [ 2.334749@0] AML_NAND_NEW_OOB : new oob
- [ 2.338402@0] bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
- [ 2.346263@0] boot_device_flag = 0
- [ 2.351415@0] hynix nand get default reg value at blk:8, page:2048
- [ 2.356444@0] NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 0
- [ 2.368224@0] NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
- [ 2.372786@0] nand shipped bbt at block 6
- [ 2.392577@0] NAND CKECK : arg phyp: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 1
- [ 2.429997@0] NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 56
- [ 2.433120@0] i=0,register --- nand_key
- [ 2.436625@0] amlnand_phydev_init,1179,phydev->offset=6000000,phydev->size=24800000
- [ 2.444253@0] amlnand_phydev_init,1179,phydev->offset=2a800000,phydev->size=4f800000
- [ 2.451967@0] amlnand_phydev_init,1179,phydev->offset=7a000000,phydev->size=186000000
- [ 2.459768@0] nfcache : offset: 0x000006000000 -0x000024800000 : partitons 1 : single_chip multi_plane
- [ 2.469300@0] nfcode : offset: 0x00002a800000 -0x00004f800000 : partitons 6 : single_chip multi_plane
- [ 2.478835@0] nfdata : offset: 0x00007a000000 -0x000186000000 : partitons 1 : single_chip multi_plane
- [ 2.490239@0] bad block count = 0
- [ 2.490239@0]
- [ 2.497357@0] bad block count = 0
- [ 2.497357@0]
- [ 2.507829@1] usb 1-1: new high-speed USB device number 2 using dwc_otg
- [ 2.509020@3] Indeed it is in host mode hprt0 = 00001101
- [ 2.518435@0] bad block count = 0
- [ 2.518435@0]
- [ 2.519027@0] amlnand_add_nftl:
- [ 2.522151@0] Creating 1 ntd partitions
- [ 2.525962@0] block_num 146
- [ 2.530735@0] ------init_ntd
- [ 2.532052@0] ntd: Giving out device 0 to nfcache
- [ 2.536363@0] Creating 6 ntd partitions
- [ 2.540212@0] block_num 318
- [ 2.547414@0] ntd: Giving out device 1 to nfcode
- [ 2.547632@0] Creating 1 ntd partitions
- [ 2.551479@0] block_num 1560
- [ 2.574937@0] ntd: Giving out device 2 to nfdata
- [ 2.575450@0] boot_device_flag : 0
- [ 2.577292@0] register_ntd_blktrans start
- [ 2.581335@0] ntd device 250!
- [ 2.584227@0] ntd->name: nfcache
- [ 2.587436@0] adjust_block_num : 4,reserved_block_ratio 10
- [ 2.592925@0] nftl version 150204a
- [ 2.596276@0] nftl build Feb 4 2015_21:22:11
- [ 2.600642@0] nftl part attr 0
- [ 2.605527@0] nftl start:146,17
- [ 2.606925@0] first
- [ 2.688192@0] average_erase_count:0
- [ 2.688218@0] second 11,129
- [ 2.688815@0] part->max_discard_block = 4
- [ 2.699285@0] all block full!!
- [ 2.699306@0] all discard block full!!
- [ 2.700428@0] free block cnt = 135
- [ 2.703808@0] new current block is 139
- [ 2.707539@0] total discard page count is 0
- [ 2.711718@0] create_part_list:1238,current_used_discard_block=133,current_discard_block_used_count=16
- [ 2.719041@3] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
- [ 2.719046@3] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
- [ 2.719050@3] usb 1-1: Product: USB2.0 Hub
- [ 2.719637@3] hub 1-1:1.0: USB hub found
- [ 2.719906@3] hub 1-1:1.0: 4 ports detected
- [ 2.721472@3] Indeed it is in host mode hprt0 = 00021501
- [ 2.753106@0] unmappig_pages=31466,discarded_pages=0,mapping_pages=1558
- [ 2.759146@0] nftl ok!
- [ 2.761865@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 2.766439@0] aml_nftl_add_ntd ok
- [ 2.769376@0] ntd device 250!
- [ 2.772291@0] ntd->name: nfcode
- [ 2.775408@0] adjust_block_num : 4,reserved_block_ratio 10
- [ 2.780893@0] nftl version 150204a
- [ 2.784249@0] nftl build Feb 4 2015_21:22:11
- [ 2.788634@0] nftl part attr 0
- [ 2.795689@0] nftl start:318,33
- [ 2.796010@0] first
- [ 2.897834@3] usb 2-1: new full-speed USB device number 2 using dwc_otg
- [ 2.898947@3] Indeed it is in host mode hprt0 = 00021501
- [ 2.958746@0] average_erase_count:0
- [ 2.958777@0] second 293,285
- [ 2.959455@0] part->max_discard_block = 4
- [ 3.099939@3] usb 2-1: New USB device found, idVendor=046d, idProduct=c52b
- [ 3.101179@3] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- [ 3.108473@3] usb 2-1: Product: USB Receiver
- [ 3.112705@3] usb 2-1: Manufacturer: Logitech
- [ 3.123608@3] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-lm0-1/input2
- [ 3.135646@0] current_block1:23
- [ 3.139606@0] recover_current_block_mapping invalid page data!!
- [ 3.140460@0] recover_current_block_mapping invalid page data!!
- [ 3.146362@0] recover_current_block_mapping invalid page data!!
- [ 3.152286@0] recover_current_block_mapping invalid page data!!
- [ 3.158148@0] recover_current_block_mapping invalid page data!!
- [ 3.164038@0] recover_current_block_mapping invalid page data!!
- [ 3.169892@0] all discard block full!!
- [ 3.173187@0] free block cnt = 45
- [ 3.176375@0] new current block is 25
- [ 3.208086@3] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
- [ 3.323418@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
- [ 3.368113@3] usb 1-1.1: new high-speed USB device number 4 using dwc_otg
- [ 3.528158@3] usb 1-1.1: new high-speed USB device number 5 using dwc_otg
- [ 3.550257@3] usb 1-1.1: New USB device found, idVendor=05e3, idProduct=0718
- [ 3.551674@3] usb 1-1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=2
- [ 3.559137@3] usb 1-1.1: Product: USB Storage
- [ 3.563463@3] usb 1-1.1: SerialNumber: 000000000033
- [ 3.569046@3] usb-storage 1-1.1:1.0: USB Mass Storage device detected
- [ 3.574917@3] scsi0 : usb-storage 1-1.1:1.0
- [ 3.814765@0] recover_current_block_mapping : fill the current block, from page 255
- [ 3.816777@0] total discard page count is 0
- [ 3.820960@0] create_part_list:1238,current_used_discard_block=24,current_discard_block_used_count=336
- [ 3.831455@0] unmappig_pages=7710,discarded_pages=0,mapping_pages=65250
- [ 3.836798@0] nftl ok!
- [ 3.839717@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.844204@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.848777@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.853335@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.857960@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.862548@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 3.867058@0] aml_nftl_add_ntd ok
- [ 3.870033@0] ntd device 250!
- [ 3.872949@0] ntd->name: nfdata
- [ 3.876068@0] adjust_block_num : 4,reserved_block_ratio 10
- [ 3.881554@0] nftl version 150204a
- [ 3.884907@0] nftl build Feb 4 2015_21:22:11
- [ 3.889388@0] nftl part attr 0
- [ 3.912329@0] nftl start:1560,146
- [ 3.913637@0] first
- [ 4.734431@0] found discard block:1524
- [ 4.752189@0] average_erase_count:0
- [ 4.752238@0] second 323,1414
- [ 4.752984@0] part->max_discard_block = 4
- [ 4.946154@0] current_block1:1236
- [ 4.955246@0] recover_current_block_mapping invalid page data!!
- [ 4.956103@0] recover_current_block_mapping invalid page data!!
- [ 4.962018@0] recover_current_block_mapping invalid page data!!
- [ 4.967890@0] recover_current_block_mapping invalid page data!!
- [ 4.973786@0] recover_current_block_mapping invalid page data!!
- [ 4.981016@0] recover_current_block_mapping invalid page data!!
- [ 4.986026@0] currnet_discard_block1:1524
- [ 4.990811@0] reach the last discard page:2
- [ 4.994232@0] free block cnt = 1265
- [ 4.996609@0] new current block is 1237
- [ 5.146712@0] prio_garbage_collect_no_last_page_in_create_list put_phy_block_to_free_list!
- [ 5.635004@0] recover_current_block_mapping : fill the current block, from page 255
- [ 5.637014@0] total discard page count is 2
- [ 5.641200@0] create_part_list:1238,current_used_discard_block=1524,current_discard_block_used_count=36
- [ 5.657372@0] unmappig_pages=322324,discarded_pages=1849,mapping_pages=37811
- [ 5.658823@0] nftl ok!
- [ 5.661694@0] Enable QUEUE_FLAG_DISCARD for NFTL
- [ 5.666142@0] aml_nftl_add_ntd ok
- [ 5.669036@0] init_aml_nftl end
- [ 5.672254@0] ethernet_driver probe!
- [ 5.675682@0] Please config phy interface.
- [ 5.679866@0] Please config savepowermode.
- [ 5.683914@0] Please config reset_pin_enable.
- [ 5.688272@0] Please config reset_delay.
- [ 5.692149@0] Please config reset_pin.
- [ 5.695878@0] ethernetinit(dbg[c0c01b84]=1)
- [ 5.700074@0] ethernet base addr is fe0c0000
- [ 5.704285@0] write mac add to:ed950348: 00 01 db 88 06 e4 |......|
- [ 5.713145@0] libphy: AMLMAC MII Bus: probed
- [ 5.714776@0] eth0: PHY ID 02430c54 at 0 IRQ -1 (0:00) active
- [ 5.722441@3] Amlogic A/V streaming port init
- [ 5.726360@3] buffersize=262144,0,start=0
- [ 5.728855@3] Subtitle stbuf alloced at 0xecc40000, size = 262144
- [ 5.734908@3] changed the (2) buffer size from 0 to 262144
- [ 5.740650@3] init vdec memsource ca00000->1c9fffff
- [ 5.745409@3] [tsync_pcr_init]init success.
- [ 5.749471@3] amvideocap_init_module
- [ 5.753251@3] regist mpeg12 codec profile
- [ 5.757088@3] regist mpeg4 codec profile
- [ 5.760918@3] amvdec_vc1 module init
- [ 5.764550@3] regist vc1 codec profile
- [ 5.768195@3] amvdec_h264 module init
- [ 5.771939@3] regist h264 codec profile
- [ 5.775639@3] amvdec_h264mvc module init
- [ 5.779641@3] regist hmvc codec profile
- [ 5.783355@3] amvdec_h264_4k2k module init
- [ 5.787513@3] regist h264_4k2k codec profile
- [ 5.791684@3] amvdec_h265 module init
- [ 5.795404@3] regist hevc_unsupport codec profile
- [ 5.800097@3] regist mjpeg codec profile
- [ 5.803898@3] amvdec_real module init
- [ 5.807632@3] amvdec_avs module init
- [ 5.811319@3] amvenc_avc memory resource undefined.
- [ 5.815943@3] encode_wq_init.
- [ 5.818902@3] encode start monitor.
- [ 5.822408@1] encode workqueue monitor start.
- [ 5.826910@3] jpegenc module init
- [ 5.830301@3] alloc_keep_buffer keep_y_addr ec600000
- [ 5.834942@3] alloc_keep_buffer keep_u_addr ecd00000
- [ 5.839885@3] alloc_keep_buffer keep_v_addr ec200000
- [ 5.844811@3] yaddr=ec600000,u_addr=ecd00000,v_addr=ec200000
- [ 5.850758@3] create_ge2d_work_queue video task ok
- [ 5.855304@3] video2_init enter
- [ 5.858912@3]
- [ 5.858912@3]
- [ 5.858912@3] VECM init
- [ 5.858912@3]
- [ 5.866213@3] efuse===========================================
- [ 5.871982@3] efuse: device efuse created
- [ 5.875860@3] efuse--------------------------------------------
- [ 5.881661@3] SARADC Driver init.
- [ 5.885095@3] __saradc_probe__
- [ 6.015077@3] scsi 0:0:0:0: Direct-Access USB TO I DE/SATA Device 0016 PQ: 0 ANSI: 4
- [ 6.020773@3] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
- [ 6.025022@3] sd 0:0:0:0: [sda] Asking for cache data failed
- [ 6.029699@3] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 6.037947@3] saradc calibration: ref_val = 509
- [ 6.040427@3] saradc calibration: ref_nominal = 512
- [ 6.045271@3] saradc calibration: coef = 4080
- [ 6.049748@3] Remote Driver
- [ 6.052476@3] Remote platform_data g_remote_base=fe600580
- [ 6.057792@3] set drvdata completed
- [ 6.061342@3] device_create_file completed
- [ 6.065964@3] input: aml_keypad as /devices/platform/meson-remote/input/input0
- [ 6.073095@3] input_register_device completed
- [ 6.077326@3] [0xffffff00] = 0x1dd0190
- [ 6.081022@3] [0xffffff04] = 0xf800ca
- [ 6.084630@3] [0xffffff08] = 0x82006e
- [ 6.088315@3] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
- [ 6.094632@3] [0xffffff0c] = 0x3c0030
- [ 6.098297@3] [0xffffff10] = 0x30fa0013
- [ 6.102055@3] [0xffffff18] = 0x6f19000
- [ 6.105793@3] [0xffffff1c] = 0xbe40
- [ 6.109265@3] [0x0] = 0xfa00a0
- [ 6.112291@3] [0x4] = 0xfa00a0
- [ 6.115315@3] [0x8] = 0xfa00a0
- [ 6.118366@3] [0xc] = 0x640030
- [ 6.121383@3] [0x10] = 0x30fa0013
- [ 6.124686@3] [0x18] = 0x961b800
- [ 6.127912@3] [0x1c] = 0x9740
- [ 6.130832@3] [0x20] = 0x104
- [ 6.133719@3] sd 0:0:0:0: [sda] Asking for cache data failed
- [ 6.139337@3] sd 0:0:0:0: [sda] Assuming drive cache: write through
- [ 6.139344@1] [0x24] = 0x0
- [ 6.139345@1] [0x28] = 0x0
- [ 6.139348@1] set_remote_mode[69]
- [ 6.139367@1] remote config major:234
- [ 6.139574@1] physical address:0x2db58000
- [ 6.139657@1] GPIO Keypad Driver init.
- [ 6.139730@1] ==gpio_key_probe==
- [ 6.139753@1] reg:2620,clearmask=400040,setmask=1
- [ 6.139756@1] reg:2622,clearmask=ff0000,set pin=3
- [ 6.139758@1] reg:2623,clearmask=7000000,setmask=7
- [ 6.139761@1] reg:2620,clearmask=800080,setmask=10001
- [ 6.139764@1] reg:2622,clearmask=ff000000,set pin=3
- [ 6.139766@1] reg:2623,clearmask=70000000,setmask=7
- [ 6.139785@1] power key(116) registed.
- [ 6.139953@1] input: gpio_keypad as /devices/platform/gpio_keypad.6/input/input1
- [ 6.140083@1] gpio keypad register input device completed.
- [ 6.140088@1] gpio keypad major:233
- [ 6.140341@1] VFD Driver################################
- [ 6.140376@1] ###################vfd_probe
- [ 6.140384@1] VFD init ---CONFIG_VFD_TM1628####vfd_stb_gpio is 32
- [ 6.140393@1] ####vfd_clk_gpio is 35
- [ 6.140399@1] ####vfd_stb_gpio is 34
- [ 6.140403@1] ####################come here #####################
- [ 6.155866@1] up vfd key(103) registed.
- [ 6.155868@1] down vfd key(108) registed.
- [ 6.155870@1] right vfd key(106) registed.
- [ 6.155871@1] back vfd key(158) registed.
- [ 6.155873@1] left vfd key(105) registed.
- [ 6.155875@1] ok vfd key(232) registed.
- [ 6.156030@1] input: vfd_keypad as /devices/platform/m1-vfd.0/input/input2
- [ 6.156163@1] vfd config major:232
- [ 6.156433@1] spi_nor_init
- [ 6.156543@1] amlogic_spi_nor_probe:
- [ 6.156548@1] amlogic_spi->state_name:default
- [ 6.156676@1] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated
- [ 6.156780@1] check_storage_device : spi boot_device_flag : 0
- [ 6.156782@1] spi_nor_probe
- [ 6.156812@1] spi_nor apollospi:32766: mx25l160 (2048 Kbytes)
- [ 6.156911@1] Creating 2 MTD partitions on "apollospi:32766":
- [ 6.156917@1] 0x000000000000-0x000000100000 : "bootloader"
- [ 6.157621@1] 0x000000100000-0x000000110000 : "ubootenv"
- [ 6.158272@1] amlogic_spi_nor_probe over
- [ 6.158413@1] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
- [ 6.342995@3] sd 0:0:0:0: [sda] Attached SCSI disk
- [ 6.348043@1] host->base fe108c20
- [ 6.351016@1] pdata->caps 7
- [ 6.353762@1] pdata->caps2 0
- [ 6.356623@1] get property: port, value:0x00000001
- [ 6.363134@1] get property: ocr_avail, value:0x00200000
- [ 6.369637@1] get property: f_min, value:0x000493e0
- [ 6.376126@1] get property: f_max, value:0x02faf080
- [ 6.382636@1] get property: max_req_size, value:0x00020000
- [ 6.389135@1] get property: irq_in, value:0x00000003
- [ 6.395630@1] get property: irq_out, value:0x00000005
- [ 6.402151@1] get property: gpio_cd, str:CARD_6
- [ 6.408121@1] get property: pinname, str:sd
- [ 6.413747@1] get property: jtag_pin, str:CARD_0
- [ 6.419734@1] get property: card_type, value:0x00000005
- [ Å]
- [ 6.627848@1]
- [ 6.627848@1]
- [ 6.627848@1]
- [ 6.637108@1] [0;40;32m JTAG in[0m
- [ 6.677846@1] reg:2620,clearmask=80008,setmask=10001
- [ 6.677885@1] reg:2621,clearmask=ff000000,set pin=64
- [ 6.682197@1] reg:2623,clearmask=7000,setmask=7
- [ 6.686704@1] reg:2620,clearmask=200020,setmask=1
- [ 6.691471@1] reg:2622,clearmask=ff00,set pin=64
- [ 6.696065@1] reg:2623,clearmask=700000,setmask=7
- [ 6.707873@2] pdata->caps 80000507
- [ 6.707903@2] pdata->caps2 0
- [ 6.708497@2] get property: port, value:0x00000002
- [ 6.714998@2] get property: ocr_avail, value:0x00200000
- [ 6.721511@2] get property: f_min, value:0x000493e0
- [ 6.728007@2] get property: f_max, value:0x02faf080
- [ 6.734501@2] get property: f_max_w, value:0x02faf080
- [ 6.741009@2] get property: max_req_size, value:0x00020000
- [ 6.747508@2] get property: pinname, str:emmc
- [ 6.753317@2] get property: card_type, value:0x00000001
- [ 6.759820@2] get property: gpio_dat3, str:BOOT_3
- [ 6.765794@2] [is_emmc_exist] host->storage_flag=4, POR_BOOT_VALUE=5
- [ 6.772127@2] [aml_sdio_probe]: there is not eMMC/tsd, skip sdio_c dts config!
- [ 6.779339@2] pdata->caps 107
- [ 6.782263@2] pdata->caps2 0
- [ 6.785124@2] get property: port, value:0x00000000
- [ 6.791630@2] get property: ocr_avail, value:0x00200000
- [ 6.798131@2] get property: f_min, value:0x000493e0
- [ 6.804627@2] get property: f_max, value:0x02faf080
- [ 6.811134@2] get property: max_req_size, value:0x00020000
- [ 6.817633@2] get property: pinname, str:sdio
- [ 6.823443@2] get property: card_type, value:0x00000003
- [ 6.867834@2] [aml_sdio_probe] aml_sdio_probe() success!
- [ 6.868128@2] [dsp]DSP start addr 0xc5e00000
- [ 6.871771@2] [dsp]register dsp to char divece(257)
- [ 6.877029@2] amlogic audio spdif interface device init!
- [ 6.881959@2] name=nand_key nand_key
- [ 6.885808@2] register_aes_algorithm:488,new way
- [ 6.890405@2] key name:keyexample, key data:1234567890
- [ 6.895784@2] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0
- [ 6.902482@2] input: rn5t618_pmu as /devices/i2c-0/0-0032/rn5t618_pmu.0/input/input3
- [ 6.909092@2] [RN5T618] NO BATTERY_PARAMETERS FOUND
- [ 6.913794@2] [RN5T618]rn5t618_otg_change, value:1, is_short:0
- [ 6.920700@2] register 0xB3:33
- [ 6.925670@2] ------------[ cut here ]------------
- [ 6.927411@2] WARNING: at kernel/workqueue.c:1368 __queue_work+0x248/0x368()
- [ 6.934422@2] Modules linked in:
- [ 6.937633@2] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 3.10.86 #1
- [ 6.943800@2] [<c0014d84>] (unwind_backtrace+0x0/0xec) from [<c0011dac>] (show_stack+0x10/0x14)
- [ 6.952459@2] [<c0011dac>] (show_stack+0x10/0x14) from [<c00321d8>] (warn_slowpath_common+0x54/0x6c)
- [ 6.961559@2] [<c00321d8>] (warn_slowpath_common+0x54/0x6c) from [<c003228c>] (warn_slowpath_null+0x1c/0x24)
- [ 6.971354@2] [<c003228c>] (warn_slowpath_null+0x1c/0x24) from [<c004c0d8>] (__queue_work+0x248/0x368)
- [ 6.980630@2] [<c004c0d8>] (__queue_work+0x248/0x368) from [<c004c238>] (queue_work_on+0x40/0x4c)
- [ 6.989476@2] [<c004c238>] (queue_work_on+0x40/0x4c) from [<c05485f8>] (rn5t618_otg_change+0x184/0x1ac)
- [ 6.998835@2] [<c05485f8>] (rn5t618_otg_change+0x184/0x1ac) from [<c05488cc>] (rn5t618_battery_probe+0x2ac/0x5b0)
- [ 7.009064@2] [<c05488cc>] (rn5t618_battery_probe+0x2ac/0x5b0) from [<c0314414>] (driver_probe_device+0xd4/0x21c)
- [ 7.019290@2] [<c0314414>] (driver_probe_device+0xd4/0x21c) from [<c0314608>] (__driver_attach+0x68/0x8c)
- [ 7.028828@2] [<c0314608>] (__driver_attach+0x68/0x8c) from [<c03128bc>] (bus_for_each_dev+0x4c/0xa4)
- [ 7.038013@2] [<c03128bc>] (bus_for_each_dev+0x4c/0xa4) from [<c0313afc>] (bus_add_driver+0xd0/0x25c)
- [ 7.047200@2] [<c0313afc>] (bus_add_driver+0xd0/0x25c) from [<c0314c24>] (driver_register+0xa8/0x140)
- [ 7.056390@2] [<c0314c24>] (driver_register+0xa8/0x140) from [<c0547184>] (rn5t618_battery_init+0x10/0x34)
- [ 7.066012@2] [<c0547184>] (rn5t618_battery_init+0x10/0x34) from [<c0008544>] (do_one_initcall+0xa0/0x148)
- [ 7.075638@2] [<c0008544>] (do_one_initcall+0xa0/0x148) from [<c0b44bdc>] (kernel_init_freeable+0x130/0x218)
- [ 7.085433@2] [<c0b44bdc>] (kernel_init_freeable+0x130/0x218) from [<c07d29b4>] (kernel_init+0x8/0x160)
- [ 7.094793@2] [<c07d29b4>] (kernel_init+0x8/0x160) from [<c000e0a0>] (ret_from_fork+0x14/0x34)
- [ 7.103376@2] ---[ end trace b65d29bed07db36e ]---
- [ 7.214372@2] vdin_drv_init: major 230
- [ 7.214634@2] vdin1 mem_start = 0x1ca00000, mem_size = 0x1000000
- [ 7.218484@2] vdin_drv_probe: driver initialized ok
- [ 7.223436@2] amvdec_656in module: init.
- [ 7.227219@2] amvdec_656in_init_module:major 229
- [ 7.232195@2] amvdec_656in probe ok.
- [ 7.235759@2] amvdec_csi probe ok.
- [ 7.238822@2] [viuin..]viuin_init_module viuin module init
- [ 7.244418@2] [viuin..]viuin_probe probe ok.
- [ 7.248869@2] [isp..]isp_probe isp probe ok.
- [ 7.252769@2] [sii9233a_drv_init] Ver: 2013Nov12
- [ 7.258478@2] amaudio2: device amaudio2 created
- [ 7.261969@2] Error: Didn't get power valid value --- wifi_power_probe 323
- [ 7.268675@2] wifi_power power_gpio is 6
- [ 7.272554@2] wifi_power power_gpio2 is 123
- [ 7.277002@2] amlogic rfkill init
- [ 7.280171@2] not get gpio_en
- [ 7.282954@2] not get gpio_wake
- [ 7.307951@0] wifi_request_32k_clk : OFF-->ON for bt_rfkill
- [ 7.307987@0] clock_32k_pin(122) : (null)
- [ 7.311875@0] clock_32k_pin(122) : sdio_wifi
- [ 7.479561@0] UMP: UMP device driver 0000 loaded
- [ 7.479925@1] aml_hw_crypto initialization.
- [ 7.483268@1] usbcore: registered new interface driver snd-usb-audio
- [ 7.489480@1] enter rt5616_modinit
- [ 7.492606@1] dummy_codec_platform_probe
- [ 7.496509@1] == ES8323 == es8323_modinit()
- [ 7.501121@1] i2s get no clk src setting in dts, use the default mpll 0
- [ 7.507145@1] [aml-i2s-dai]enterd aml_i2s_dai_probe,old_samplerate:0,sample_rate=48000
- [ 7.515288@1] [aml-spdif-dai]enter aml_dai_spdif_init
- [ 7.520155@1] [aml-spdif-dai]enterd aml_spdif_play,set_clock:-1,sample_rate=4
- [ 7.527251@1] audio_set_958_clk, freq=4,
- [ 7.531182@1] IEC958 16bit
- [ 7.533841@1] hdmitx: audio: aout notify rate 48000
- [ 7.538717@1] hdmitx: audio: aout notify size 16
- [ 7.543288@1] hdmitx: audio: aout notify format CT_PCM
- [ 7.548411@1] hdmitx: audio: audio channel num is 1
- [ 7.553259@1] hdmitx: audio: SPDIF
- [ 7.556645@1] hdmitx: audio: current VIC: 16
- [ 7.560891@1] hdmitx: audio: audio sample rate: 3
- [ 7.565565@1] hdmitx: audio: set audio N para
- [ 7.569909@1] hdmitx: audio: PCM out to HDMI
- [ 7.574147@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 7.578832@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 7.584031@1] hdmitx: audio: Audio Type: PCM
- [ 7.588333@1] hdmitx: audio: set audio param
- [ 7.592583@1] [aml-spdif-dai]aml_spdif_probe
- [ 7.597019@1] test codec dummy_codec
- [ 7.600424@1] using external codec, index = 1
- [ 7.604745@1] using external dummy codec
- [ 7.608790@1] enter spdif_dit_probe
- [ 7.612200@1] aml_spdif_unmute
- [ 7.615517@1] codec_name = dummy_codec.0
- [ 7.619507@1] p_aml_audio->hp_disable=1
- [ 7.623036@1] falied to get spk event delay time paraments from dts file
- [ 7.629720@1] spk_event delay_time = 0
- [ 7.634518@1] aml-i2s 0:playback preallocate_dma_buffer: area=ef300000, addr=2f500000, size=524288
- [ 7.642696@1] aml-i2s 1:capture preallocate_dma_buffer: area=ef240000, addr=2f440000, size=65536
- [ 7.651161@1] aml_snd_m8 aml_m8_sound_card.5: dummy_codec <-> aml-i2s-dai.0 mapping ok
- [ 7.660387@1] aml-i2s 0:playback preallocate_dma_buffer: area=ef400000, addr=2f600000, size=524288
- [ 7.668353@1] aml-i2s 1:capture preallocate_dma_buffer: area=ef260000, addr=2f460000, size=65536
- [ 7.676793@1] aml_snd_m8 aml_m8_sound_card.5: dit-hifi <-> aml-spdif-dai.0 mapping ok
- [ 7.685718@1] -----ext_codec=1---
- [ 7.687984@1] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0
- [ 7.694102@1] Netfilter messages via NETLINK v0.30.
- [ 7.698852@1] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
- [ 7.705521@1] ctnetlink v0.93: registering with nfnetlink.
- [ 7.710564@1] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
- [ 7.717606@1] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
- [ 7.724087@1] xt_time: kernel timezone is -0000
- [ 7.728181@1] ipip: IPv4 over IPv4 tunneling driver
- [ 7.733483@1] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 7.738525@1] arp_tables: (C) 2002 David S. Miller
- [ 7.743205@1] TCP: cubic registered
- [ 7.746644@1] Initializing XFRM netlink socket
- [ 7.751589@1] NET: Registered protocol family 10
- [ 7.756195@1] mip6: Mobile IPv6
- [ 7.758835@1] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 7.764476@1] sit: IPv6 over IPv4 tunneling driver
- [ 7.770021@1] NET: Registered protocol family 17
- [ 7.773707@1] NET: Registered protocol family 15
- [ 7.778344@1] Bridge firewalling registered
- [ 7.782510@1] Bluetooth: RFCOMM TTY layer initialized
- [ 7.787489@1] Bluetooth: RFCOMM socket layer initialized
- [ 7.792798@1] Bluetooth: RFCOMM ver 1.11
- [ 7.796661@1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
- [ 7.802130@1] Bluetooth: BNEP filters: protocol multicast
- [ 7.807501@1] Bluetooth: BNEP socket layer initialized
- [ 7.812629@1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
- [ 7.818689@1] Bluetooth: HIDP socket layer initialized
- [ 7.823834@1] l2tp_core: L2TP core driver, V2.0
- [ 7.828318@1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
- [ 7.833240@1] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
- [ 7.838991@1] l2tp_netlink: L2TP netlink interface
- [ 7.843752@1] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
- [ 7.849817@1] l2tp_debugfs: L2TP debugfs support
- [ 7.854390@1] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
- [ 7.861017@1] NET: Registered protocol family 35
- [ 7.865620@1] Key type dns_resolver registered
- [ 7.870925@1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
- [ 7.877819@1] Registering SWP/SWPB emulation handler
- [ 7.882737@1] enter meson_pm_init
- [ 7.886149@1] enter meson_pm_probe!
- [ 7.889514@1] meson_pm_probe done !
- [ 7.893493@1] regulator-dummy: disabling
- [ 7.897338@1] aml_rtc rtc.0: setting system clock to 2001-11-01 19:11:40 UTC (1004641900)
- [ 7.905044@1] ### dt-test ### No testcase data in device tree; not running tests
- [ 7.912471@1] meson_cpufreq: no voltage_control prop
- [ 7.917321@1] voltage_control = 0
- [ 7.921839@1] hdmitx: cec: CEC init
- [ 7.924225@1] hdmitx: cec: CEC task process
- [ 7.928271@1] input: cec_input as /devices/virtual/input/input4
- [ 7.934260@1] hdmitx: cec: hdmitx_device->cec_init_ready:0x1
- [ 7.93[ 7.957814@1] Changing uart_ao_ttyS0: baud from 0 to 115200
- [ 7.977980@1] Freeing unused kernel memory: 356K (c0b44000 - c0b9d000)
- e2fsck 1.42.12 (29-Aug-2014)
- [ 7.999004@2] aml_nftl_open ok!
- [ 7.999068@2] aml_nftl_open ok!
- Pass 1: Checking inodes, blocks, and sizes
- Pass 2: Checking directory structure
- Pass 3: Checking directory connectivity
- Pass 4: Checking reference counts
- Pass 5: Checking group summary information
- /dev/system: 1956/65536 files (1.5% non-contiguous), 252449/262144 blocks
- e2fsck 1.42.12 (29-Aug-2014)
- [ 8.150666@2] aml_nftl_open ok!
- [ 8.151605@2] aml_nftl_open ok!
- Pass 1: Checking inodes, blocks, and sizes
- Pass 2: Checking directory structure
- Pass 3: Checking directory connectivity
- Pass 4: Checking reference counts
- Pass 5: Checking group summary information
- /dev/data: 936/362160 files (8.8% non-contiguous), 151729/1447936 blocks
- [ 8.502071@0] tvmode set to 720p
- [ 8.502071@0]
- [ 8.502309@0] mode is 11,sync_duration_den=1,sync_duration_num=60
- [ 8.508418@0] TV mode 720p selected.
- [ 8.511925@0] tvoutc_setmode[489]
- [ 8.515217@0] new mode 720p
- [ 8.515217@0] set ok
- [ 8.520263@0] hdmitx: video: get current mode: 720p
- [ 8.525100@0] is_similar_hdmi_vic[325] vic_old=16,mode_new=11
- [ 8.530835@0] hdmitx: video: get current mode: 720p
- [ 8.535676@0] is_similar_hdmi_vic[325] vic_old=16,mode_new=11
- [ 8.541410@0] hdmitx: system: gate/pwr cmd: 7
- [ 8.545770@0] hdmitx: system: already init VIC = 0 Now VIC = 4
- [ 8.551670@0] hdmitx: system: 4 (cd0,cs0,pm1,vd0,1)
- [ 8.556650@0] hdmitx: system: gate/pwr cmd: 0
- [ 8.561001@0] hdmitx: system: hw reset
- [ 8.565752@0] hdmitx: audio: SPDIF
- [ 8.568159@0] hdmitx: system: reconfig packet setting done
- [ 8.707816@1] hdmitx: system: phy setting done
- [ 8.727827@1] hdmitx: system: set pll
- [ 8.727846@1] hdmitx: system: param->VIC:4
- [ 8.729922@1] mode is: 11
- [ 8.732522@1] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 8.736595@1] viu chan = 1
- [ 8.739287@1] VPU_VIU_VENC_MUX_CTRL: 0x22a
- [ 8.743356@1] config HPLL
- [ 8.745957@1] set_hpll_clk_out[62] clk = 2970
- [ 8.767811@1] config HPLL done
- [ 8.767833@1] enc_vpu_bridge_reset[292]
- [ 8.907814@1] hdmitx: system: phy setting done
- [ 8.907837@1] Sink is HDMI device
- [ 8.909910@1] No sink attached
- [ 8.912976@1] hdmitx: audio: audio channel num is 1
- [ 8.917798@1] hdmitx: audio: SPDIF
- [ 8.921189@1] hdmitx: audio: current VIC: 4
- [ 8.925337@1] hdmitx: audio: audio sample rate: 3
- [ 8.930022@1] hdmitx: audio: set audio N para
- [ 8.934356@1] hdmitx: audio: PCM out to HDMI
- [ 8.938604@1] hdmitx: audio: i2s_to_spdif_flag:1
- [ 8.943280@1] hdmitx: audio: Enable audio spdif to HDMI
- [ 8.948487@1] hdmitx: audio: Audio Type: PCM
- [ 8.953388@1] set_vout_mode[249]
- [ 9.035519@1] vfm_map_store:rm default
- [ 9.035519@1]
- [ 9.035595@1] vfm_map_store:add default decoder ppmgr deinterlace amvideo
- [ 9.035595@1]
- [H[J[H[J[ 9.053107@3] aml_nftl_open ok!
- [ 9.053327@3] blktrans_ioctl -cmd: 5331,801c0204,64
- [ 9.081386@3] aml_nftl_open ok!
- [ 9.081588@3] blktrans_ioctl -cmd: 5331,801c0204,64
- [ 9.083580@1] aml_nftl_open ok!
- [ 9.083618@1] aml_nftl_open ok!
- [ 9.112131@1] aml_nftl_open ok!
- [ 9.112192@1] aml_nftl_open ok!
- [ 9.127989@0] aml_nftl_open ok!
- [ 9.128728@0] EXT3-fs (system): error: couldn't mount because of unsupported optional features (40)
- [ 9.134575@0] aml_nftl_open ok!
- [ 9.137716@0] EXT2-fs (system): error: couldn't mount because of unsupported optional features (40)
- [ 9.146719@0] aml_nftl_open ok!
- [ 9.149842@0] force enable DISCARD here for ext4 fs
- [ 9.156309@0] checked enable EXT4 DISCARD here
- [ 9.159071@0] EXT4-fs (system): mounted filesystem with ordered data mode. Opts: (null)
- [ 9.254998@0] aml_nftl_open ok!
- [ 9.255750@0] EXT3-fs (data): error: couldn't mount because of unsupported optional features (40)
- [ 9.261447@0] aml_nftl_open ok!
- [ 9.264534@0] EXT2-fs (data): error: couldn't mount because of unsupported optional features (40)
- [ 9.273396@0] aml_nftl_open ok!
- [ 9.276487@0] force enable DISCARD here for ext4 fs
- [ 9.283742@0] checked enable EXT4 DISCARD here
- [ 9.285705@0] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: (null)
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement