Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ❰greg❙~❱✘≻ sudo smartctl -a /dev/sda
- [sudo] password for greg:
- smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.62-1-MANJARO] (local build)
- Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Toshiba 2.5" HDD MQ01ABD...
- Device Model: TOSHIBA MQ01ABD100
- Serial Number: 76QPTNIIT
- LU WWN Device Id: 5 000039 721c0ba2c
- Firmware Version: AX0P3D
- User Capacity: 1,000,204,886,016 bytes [1.00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 5400 rpm
- Form Factor: 2.5 inches
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ATA8-ACS (minor revision not indicated)
- SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Sun Aug 4 04:08:27 2019 BST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 120) seconds.
- Offline data collection
- capabilities: (0x5b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- No Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 240) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 128
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
- 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 2396
- 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
- 9 Power_On_Hours 0x0032 066 066 000 Old_age Always - 13799
- 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2720
- 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 21883
- 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 46
- 193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 36816
- 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 32 (Min/Max 10/43)
- 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
- 240 Head_Flying_Hours 0x0032 069 069 000 Old_age Always - 12589
- 241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 16949014627
- 242 Total_LBAs_Read 0x0032 100 100 000 Old_age Always - 9250013351
- 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
- SMART Error Log Version: 1
- ATA Error Count: 276 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 276 occurred at disk power-on lifetime: 13794 hours (574 days + 18 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 04 51 ff 00 00 00 00
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- f2 00 00 00 00 00 00 00 00:00:15.437 SECURITY UNLOCK
- ec 00 00 00 00 00 00 00 00:00:15.421 IDENTIFY DEVICE
- ec 00 00 00 00 00 00 00 00:00:08.421 IDENTIFY DEVICE
- ec 00 00 00 00 00 00 00 00:00:08.420 IDENTIFY DEVICE
- ec 00 00 00 00 00 00 00 00:00:08.416 IDENTIFY DEVICE
- Error 275 occurred at disk power-on lifetime: 13793 hours (574 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 e8 08 09 01 40 Error: UNC at LBA = 0x00010908 = 67848
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 08 e8 08 09 01 40 00 00:02:04.244 READ FPDMA QUEUED
- 61 08 d8 00 08 04 40 00 00:02:04.244 WRITE FPDMA QUEUED
- ef 10 03 00 00 00 a0 00 00:02:04.181 SET FEATURES [Enable SATA feature]
- ef 10 02 00 00 00 a0 00 00:02:04.181 SET FEATURES [Enable SATA feature]
- 27 00 00 00 00 00 e0 00 00:02:04.180 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
- Error 274 occurred at disk power-on lifetime: 13793 hours (574 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 a0 08 09 01 40 Error: UNC at LBA = 0x00010908 = 67848
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 08 a0 08 09 01 40 00 00:01:59.799 READ FPDMA QUEUED
- 60 08 98 00 09 01 40 00 00:01:59.794 READ FPDMA QUEUED
- 60 08 90 00 09 81 40 00 00:01:59.788 READ FPDMA QUEUED
- 60 00 88 98 1d 41 40 00 00:01:59.787 READ FPDMA QUEUED
- 60 00 80 98 1c 41 40 00 00:01:59.786 READ FPDMA QUEUED
- Error 273 occurred at disk power-on lifetime: 13793 hours (574 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 d8 08 09 01 40 Error: UNC at LBA = 0x00010908 = 67848
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 20 78 b8 17 41 40 00 00:01:55.900 READ FPDMA QUEUED
- 60 68 70 80 13 01 40 00 00:01:52.154 READ FPDMA QUEUED
- 60 d8 68 a0 11 01 40 00 00:01:52.154 READ FPDMA QUEUED
- 60 30 60 60 11 01 40 00 00:01:52.154 READ FPDMA QUEUED
- 60 c8 58 90 0f 01 40 00 00:01:52.154 READ FPDMA QUEUED
- Error 272 occurred at disk power-on lifetime: 13793 hours (574 days + 17 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 41 58 08 09 01 40 Error: UNC at LBA = 0x00010908 = 67848
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 08 58 08 09 01 40 00 00:01:08.566 READ FPDMA QUEUED
- ef 10 03 00 00 00 a0 00 00:01:08.501 SET FEATURES [Enable SATA feature]
- ef 10 02 00 00 00 a0 00 00:01:08.500 SET FEATURES [Enable SATA feature]
- 27 00 00 00 00 00 e0 00 00:01:08.500 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
- ec 00 00 00 00 00 a0 00 00:01:08.499 IDENTIFY DEVICE
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Short offline Completed without error 00% 13739 -
- # 2 Short offline Completed: read failure 00% 13739 419129920
- # 3 Short offline Completed: read failure 00% 12950 419129920
- # 4 Short offline Aborted by host 90% 1876 -
- # 5 Short offline Aborted by host 90% 1876 -
- # 6 Short offline Completed without error 00% 8 -
- # 7 Short offline Completed without error 00% 7 -
- # 8 Short offline Completed without error 00% 6 -
- # 9 Short offline Completed without error 00% 5 -
- #10 Short offline Completed without error 00% 4 -
- #11 Short offline Completed without error 00% 3 -
- #12 Short offline Completed without error 00% 3 -
- #13 Short offline Completed without error 00% 2 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement