Adribananas Lotus

2015-11-13 18:20:04  ★ Richard Hawkins would walk  over to the toolstation as he then bends down and picks up his toolbox with his
2015-11-13 18:20:29  ★ right hand as he then picks it up and walks back to the Lotus.      ((Richard Hawkins))
2015-11-13 18:22:58  ★ Richard Hawkins would then place the toolbox down next to the lotus as he then bends down and opens the-
2015-11-13 18:23:03  ★ toolbox.      ((Richard Hawkins))
2015-11-13 18:23:44  ★ Richard Hawkins would then reach for the breaker bar and a 19mm socket, as he then connects the two.
2015-11-13 18:25:49  ★ Richard Hawkins would then use the breaker bar with the 19mm socket to loosen the nuts on the front wheel.
2015-11-13 18:26:24  ★ Richard Hawkins would then walk over to the control panel of the lift, as he then raises it a little .
2015-11-13 18:26:56  ★ Richard Hawkins would then walk over to the wall of the garage as he then bends down and
2015-11-13 18:27:08  ★ picks up 4 plastic pads with his right hand.      ((Richard Hawkins))
2015-11-13 18:27:35  ★ Richard Hawkins would then stand back up as he then walks back to the Lotus.
2015-11-13 18:28:06  ★ Richard Hawkins would then place one plastic pad to each end of the skirts, supporting the car when it's
2015-11-13 18:28:11  ★ lifted up.      ((Richard Hawkins))
2015-11-13 18:28:40  ★ Richard Hawkins would then walk back to the control panel as he then pushes a button with his right hand and
2015-11-13 18:29:04  ★ would then lift the middle part of the lift so all wheels would be off the ground.      ((Richard Hawkins))
2015-11-13 18:29:52  ★ Richard Hawkins would then walk back to the front of the car as he then unscrewes all 5 nuts holding the
2015-11-13 18:30:38  ★ wheel in place.      ((Richard Hawkins))
2015-11-13 18:30:45  Richard Hawkins: (( 4 nuts* ))
2015-11-13 18:31:11  ★ Richard Hawkins would then place the nuts into his pocket as he then grabs ahold of the wheel with both
2015-11-13 18:31:28  ★ of his hands and would take the wheel off the car.      ((Richard Hawkins))
2015-11-13 18:31:51  ★ Richard Hawkins would then place the wheel down onto the ground as he then rolls it to the side of the garag
2015-11-13 18:32:14  ★ -e wall and leans the wheel agains the wall.      ((Richard Hawkins))
2015-11-13 18:35:15  ★ Richard Hawkins would then walk back to the car as he then opens the driverside door and pulls on a lever
2015-11-13 18:35:25  ★ to open the hood/trunk of the car.      ((Richard Hawkins))
2015-11-13 18:37:07  ★ Richard Hawkins would then walk back to the front wheel as he then neds down to his toolbox and
2015-11-13 18:37:24  ★ takes a 13mm Wrench from there.      ((Richard Hawkins))
2015-11-13 18:37:59  ★ Richard Hawkins would then use the 13mm wrench to loosen both nuts of the sway bar and places the nuts into
2015-11-13 18:38:05  ★ his pocket.      ((Richard Hawkins))
2015-11-13 18:38:34  ★ Richard Hawkins would then remove the sway bar as he thenplaces the 13mm wrench onto the side of the
2015-11-13 18:38:37  ★ lift.      ((Richard Hawkins))
2015-11-13 18:40:08  ★ Richard Hawkins would then again bend down to his toolbox as he then reaches for the socket wrench and the
2015-11-13 18:40:17  ★ 17mm socket as he then connects the two.      ((Richard Hawkins))
2015-11-13 18:41:03  ★ Richard Hawkins would then use the socket wrench with the 17mm socket to remove the bolts and nuts
2015-11-13 18:41:40  ★ connecting the front shock absorber to the front steering knuckle.      ((Richard Hawkins))
2015-11-13 18:42:03  ★ Richard Hawkins would then place the nuts and pults into his pocket as he then stands up and loosens up
2015-11-13 18:42:32  ★ and removes the 3 nuts holding the front shock absorber against the chassis.      ((Richard Hawkins))
2015-11-13 18:43:00  ★ Richard Hawkins would then crouch down again as he then pushes down the front steering knuckle, while
2015-11-13 18:43:12  ★ using both of his hands to remove the front shock absorber.      ((Richard Hawkins))
2015-11-13 18:45:07  ★ Richard Hawkins would then remove the shock absorber from the front wheel hub as he then places it down
2015-11-13 18:45:21  ★ onto the ground as he then inspects it.      ((Richard Hawkins))
2015-11-13 18:45:46  ★ Richard Hawkins would then walk to the tool station where there is a new set of coilovers .
2015-11-13 18:46:16  ★ Richard Hawkins would then open one of the boxes as he then takes out the coilover and a new sway bar.
2015-11-13 18:46:35  ★ Richard Hawkins would bring the coilover  back to the car as he then places it down next to the old one.
2015-11-13 18:46:58  ★ Richard Hawkins would then compare the two before picking the nw one up and placing it into the front wheel
2015-11-13 18:47:01  ★ hub,      ((Richard Hawkins))
2015-11-13 18:47:33  ★ Richard Hawkins would then jiggle the coilover around to match it up with the bolt holes int the chassis
2015-11-13 18:47:54  ★ Richard Hawkins would then stand up as he then starts to screw on the 3 nuts holding the coilover
2015-11-13 18:47:58  ★ against the chassis.      ((Richard Hawkins))
2015-11-13 18:48:31  ★ Richard Hawkins after tightening the 3 nuts with the socket wrench he would crouch back down and
2015-11-13 18:48:53  ★ slide two bolts through the front steering knuckle and throught the coilover, as he then      ((Richard Hawkins))
2015-11-13 18:49:11  ★ Richard Hawkins uses his hands to screw on couple of nuts.
2015-11-13 18:49:35  ★ Richard Hawkins would then tighten those two bolts with his hands and after doing that he would use the
2015-11-13 18:49:50  ★ Richard Hawkins socket wrench to tighten them as tight as he can.
2015-11-13 18:50:27  ★ Richard Hawkins would then reach for the new sway bar with his right hand as he then slides it into place
2015-11-13 18:51:00  ★ Richard Hawkins would then tighten the two nuts which he takes from his pocket, with his soket wrench
2015-11-13 18:51:49  ★ after doing so, he would set the coilover to medium level, not the lowest one.      ((Richard Hawkins))
2015-11-13 18:52:24  ★ Richard Hawkins would then walk back to the wall of the garage as he picks up the wheel of the car.
2015-11-13 18:53:00  ★ Richard Hawkins would then take it to the front of the car, as he then uses bothof his hands to  lift it up
2015-11-13 18:53:32  ★ to the wheel hub and holsd it in place until he screwes in couple of nuts to hold the rim in      ((Richard Hawkins))
2015-11-13 18:53:37  ★ poistion.      ((Richard Hawkins))
2015-11-13 18:54:03  ★ Richard Hawkins would then bend down as he reaches for the torque bar and sets it to 130N:M
2015-11-13 18:54:31  ★ Richard Hawkins would then disconnect the 19mm socket from the breaker bar and would connect it to
2015-11-13 18:54:40  ★ the torque bar.      ((Richard Hawkins))
2015-11-13 18:55:17  ★ Richard Hawkins would then use the torque bar to tighten all 4 nuts of the Wheel.
2015-11-13 18:55:45  ★ Richard Hawkins would then repeat the same thing to all remaining 3 shock absorbers to the car.
2015-11-13 18:56:03  ★ Richard Hawkins would then gather all his tools and places them into the toolbox, befor taking it back to
2015-11-13 18:56:10  ★ the toolstation.      ((Richard Hawkins))
2015-11-13 18:56:36  ★ Richard Hawkins would then walk back to the car as he picks up all old shock absorbers and throws them next
2015-11-13 18:56:46  ★ to the toolstation.      ((Richard Hawkins))