Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ; PrusaSlicer start gcode for Artillery Sidewinder x1
- ; Last updated 20210310
- M300 S60 P10 ; chirp
- M117 Initializing
- ; Set coordinate modes
- G90 ; use absolute coordinates
- M83 ; extruder relative mode
- ; Reset speed and extrusion rates
- M200 D0 ; disable volumetric e
- M220 S100 ; reset speed
- ; Set print temps
- M117 Heating nozzle & bed
- M104 S160 ; set no-ooze nozzle temp while bed heats
- M140 S[first_layer_bed_temperature] ; set heatbed temperature
- M109 S160 ; wait until nozzle is warm to avoid bed damage
- ; Home
- M300 S60 P10 ; chirp
- G1 Z3 F3000 ; move z up little to prevent scratching of surface
- M117 Homing
- G28 ; home all axes
- ; Present bed for final cleaning
- M300 S60 P10 ; chirp
- G1 Z3 F3000 ; move z up little to prevent scratching of surface
- G0 X155 Y310 F7200 ; Present bed for cleaning
- ; Wait for final bed heating
- M190 S[first_layer_bed_temperature] ; wait for the bed to heat up
- ; Return to prime position and wait for nozzle to heat up
- M300 S60 P10 ; chirp
- G1 Z3 F3000 ; move z up little to prevent scratching of surface
- G1 X0 Y-2 F7200.0 ; go outside print area
- M104 S[first_layer_temperature] ; set final nozzle print temp
- M109 S[first_layer_temperature] ; wait for the nozzle to heat up
- ; Prime line routine
- M300 S60 P10 ; chirp
- M117 Printing prime line
- M900 K0; Disable Linear Advance for prime line
- G92 E0.0 ; reset extrusion distance
- G1 Z0.2 F3000 ; lower nozzle to printing height
- G1 E5 F1000 ; de-retract and push filament to trap ooze
- G1 X0 Y-3 F7200 ; move to prime line position
- G1 X20.0 E10 F7200.0 ; fat 20mm intro line @ 0.5
- G1 X60.0 E3.2 F3600.0 ; thin +40mm intro line @ 0.08
- G1 X100.0 E6 F3600.0 ; fat +40mm intro line @ 0.15
- G1 E-0.8 F3000; retract to avoid stringing
- G1 X99.5 E0 F3600.0 ; -0.5mm wipe action to avoid string
- G1 X110.0 E0 F3600.0 ; +10mm intro line @ 0.00
- G1 E0.4 F1500; de-retract
- G92 E0.0 ; reset extrusion distance
- ; Final print adjustments
- M300 S60 P10 ; chirp
- M117 Preparing to print
- ; Adjust extrusion rate if desired
- ;M221 S{if layer_height >= 0.1}90{else}100{endif} ; compensate for thick layer heights
- ;M92 E441.664 ; compensate for extrusion error
- ;M85 S300 ; activate 300-second idle timeout
- ; Adjust PID values
- ;M301 P14.93 I1.27 D43.27
- ;M304 P88.75 I11.17 D176.30
- M420 S1 Z3 ; reload and fade mesh bed leveling at 3mm
- M117 Print in progress
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement