Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 6.6 2017-11-05 r4594 [x86_64-linux-5.9.0-0.bpo.2-amd64] (local build)
- Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Device Model: WDC WD6001FSYZ-01SS7B1
- Serial Number: WD-WX41DA57HHCP
- LU WWN Device Id: 5 0014ee 2b7b28326
- Firmware Version: ER03
- User Capacity: 6,001,175,126,016 bytes [6.00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 7200 rpm
- Form Factor: 3.5 inches
- Device is: Not in smartctl database [for details use: -P showall]
- ATA Version is: ACS-3 T13/2161-D revision 5
- SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Sun Dec 20 14:06:43 2020 GMT
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- AAM feature is: Unavailable
- APM level is: 1 (minimum power consumption with standby)
- Rd look-ahead is: Enabled
- Write cache is: Disabled
- DSN feature is: Disabled
- ATA Security is: Disabled, frozen [SEC2]
- Wt Cache Reorder: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x82) Offline data collection activity
- was completed without error.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 0) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 571) minutes.
- Conveyance self-test routine
- recommended polling time: ( 6) minutes.
- SCT capabilities: (0x003d) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
- 1 Raw_Read_Error_Rate POSR-K 200 100 051 - 0
- 3 Spin_Up_Time POS--K 229 100 021 - 7541
- 4 Start_Stop_Count -O--CK 097 097 000 - 3619
- 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
- 7 Seek_Error_Rate -OSR-K 100 100 000 - 0
- 9 Power_On_Hours -O--CK 060 060 000 - 29919
- 10 Spin_Retry_Count -O--CK 100 100 000 - 0
- 11 Calibration_Retry_Count -O--CK 100 100 000 - 0
- 12 Power_Cycle_Count -O--CK 100 100 000 - 140
- 16 Unknown_Attribute -O---K 025 175 000 - 1355019100326
- 183 Runtime_Bad_Block -O--CK 100 100 000 - 0
- 192 Power-Off_Retract_Count -O--CK 200 100 000 - 62
- 193 Load_Cycle_Count -O--CK 199 100 000 - 3621
- 194 Temperature_Celsius -O---K 129 103 000 - 23
- 196 Reallocated_Event_Count -O--CK 200 100 000 - 0
- 197 Current_Pending_Sector -O--CK 200 100 000 - 0
- 198 Offline_Uncorrectable ----CK 200 100 000 - 0
- 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
- 200 Multi_Zone_Error_Rate ---R-- 200 100 000 - 0
- ||||||_ K auto-keep
- |||||__ C event count
- ||||___ R error rate
- |||____ S speed/performance
- ||_____ O updated online
- |______ P prefailure warning
- General Purpose Log Directory Version 1
- SMART Log Directory Version 1 [multi-sector log support]
- Address Access R/W Size Description
- 0x00 GPL,SL R/O 1 Log Directory
- 0x01 SL R/O 1 Summary SMART error log
- 0x02 SL R/O 5 Comprehensive SMART error log
- 0x03 GPL R/O 6 Ext. Comprehensive SMART error log
- 0x04 GPL,SL R/O 8 Device Statistics log
- 0x06 SL R/O 1 SMART self-test log
- 0x07 GPL R/O 1 Extended self-test log
- 0x08 GPL R/O 2 Power Conditions log
- 0x09 SL R/W 1 Selective self-test log
- 0x0a GPL R/W 8 Device Statistics Notification
- 0x10 GPL R/O 1 NCQ Command Error log
- 0x11 GPL R/O 1 SATA Phy Event Counters log
- 0x12 GPL R/O 1 SATA NCQ Non-Data log
- 0x13 GPL R/O 1 SATA NCQ Send and Receive log
- 0x24 GPL R/O 171 Current Device Internal Status Data log
- 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
- 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
- 0xa0-0xb6 GPL,SL VS 16 Device vendor specific log
- 0xb7 GPL,SL VS 40 Device vendor specific log
- 0xb8-0xbf GPL,SL VS 16 Device vendor specific log
- 0xc0 GPL,SL VS 1 Device vendor specific log
- 0xc8-0xca GPL,SL VS 1 Device vendor specific log
- 0xe0 GPL,SL R/W 1 SCT Command/Status
- 0xe1 GPL,SL R/W 1 SCT Data Transfer
- SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
- Device Error Count: 85 (device log contains only the most recent 24 errors)
- CR = Command Register
- FEATR = Features Register
- COUNT = Count (was: Sector Count) Register
- LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
- LH = LBA High (was: Cylinder High) Register ] LBA
- LM = LBA Mid (was: Cylinder Low) Register ] Register
- LL = LBA Low (was: Sector Number) Register ]
- DV = Device (was: Device/Head) Register
- DC = Device Control Register
- ER = Error register
- ST = Status register
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 85 [12] occurred at disk power-on lifetime: 29890 hours (1245 days + 10 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 04 -- 51 00 06 00 00 01 71 c7 32 01 00 Error: ABRT
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- ef 00 10 00 06 00 00 00 00 00 00 00 00 6d+23:22:23.581 SET FEATURES [Enable SATA feature]
- Error 84 [11] occurred at disk power-on lifetime: 29872 hours (1244 days + 16 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 04 -- 51 00 06 00 00 01 71 c7 32 01 00 Error: ABRT
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- ef 00 10 00 06 00 00 00 00 00 00 00 00 6d+05:33:51.290 SET FEATURES [Enable SATA feature]
- Error 83 [10] occurred at disk power-on lifetime: 29770 hours (1240 days + 10 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 04 -- 51 00 06 00 00 01 71 c7 32 01 00 Error: ABRT
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- ef 00 10 00 06 00 00 00 00 00 00 00 00 1d+22:56:01.235 SET FEATURES [Enable SATA feature]
- Error 82 [9] occurred at disk power-on lifetime: 29750 hours (1239 days + 14 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 04 -- 51 00 06 00 00 01 71 c7 32 01 00 Error: ABRT
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- ef 00 10 00 06 00 00 00 00 00 00 00 00 1d+03:36:51.636 SET FEATURES [Enable SATA feature]
- Error 81 [8] occurred at disk power-on lifetime: 29734 hours (1238 days + 22 hours)
- When the command that caused the error occurred, the device was in standby mode.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 04 -- 51 00 06 00 00 01 71 c7 32 01 00 Error: ABRT
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- ef 00 10 00 06 00 00 00 00 00 00 00 00 10:48:31.872 SET FEATURES [Enable SATA feature]
- Error 80 [7] occurred at disk power-on lifetime: 29733 hours (1238 days + 21 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 04 -- 51 00 06 00 00 01 71 c7 32 01 00 Error: ABRT
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- ef 00 10 00 06 00 00 00 00 00 00 00 00 09:53:00.680 SET FEATURES [Enable SATA feature]
- Error 79 [6] occurred at disk power-on lifetime: 29733 hours (1238 days + 21 hours)
- When the command that caused the error occurred, the device was in standby mode.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 04 -- 51 00 06 00 00 01 71 c7 32 01 00 Error: ABRT
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- ef 00 10 00 06 00 00 00 00 00 00 00 00 09:42:15.680 SET FEATURES [Enable SATA feature]
- Error 78 [5] occurred at disk power-on lifetime: 29732 hours (1238 days + 20 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 04 -- 51 00 06 00 00 01 71 c7 32 01 00 Error: ABRT
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- ef 00 10 00 06 00 00 00 00 00 00 00 00 09:25:04.319 SET FEATURES [Enable SATA feature]
- SMART Extended Self-test Log Version: 1 (1 sectors)
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- SCT Status Version: 3
- SCT Version (vendor specific): 258 (0x0102)
- SCT Support Level: 1
- Device State: Active (0)
- Current Temperature: 23 Celsius
- Power Cycle Min/Max Temperature: 22/43 Celsius
- Lifetime Min/Max Temperature: 13/51 Celsius
- Under/Over Temperature Limit Count: 0/0
- Vendor specific:
- 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- SCT Temperature History Version: 2
- Temperature Sampling Period: 1 minute
- Temperature Logging Interval: 1 minute
- Min/Max recommended Temperature: 0/60 Celsius
- Min/Max Temperature Limit: -41/85 Celsius
- Temperature History Size (Index): 478 (213)
- Index Estimated Time Temperature Celsius
- 214 2020-12-20 06:09 24 *****
- ... ..(135 skipped). .. *****
- 350 2020-12-20 08:25 24 *****
- 351 2020-12-20 08:26 23 ****
- ... ..( 61 skipped). .. ****
- 413 2020-12-20 09:28 23 ****
- 414 2020-12-20 09:29 24 *****
- 415 2020-12-20 09:30 24 *****
- 416 2020-12-20 09:31 24 *****
- 417 2020-12-20 09:32 25 ******
- 418 2020-12-20 09:33 25 ******
- 419 2020-12-20 09:34 26 *******
- ... ..( 16 skipped). .. *******
- 436 2020-12-20 09:51 26 *******
- 437 2020-12-20 09:52 25 ******
- ... ..( 10 skipped). .. ******
- 448 2020-12-20 10:03 25 ******
- 449 2020-12-20 10:04 24 *****
- ... ..( 27 skipped). .. *****
- 477 2020-12-20 10:32 24 *****
- 0 2020-12-20 10:33 23 ****
- ... ..(212 skipped). .. ****
- 213 2020-12-20 14:06 23 ****
- SCT Error Recovery Control:
- Read: 70 (7.0 seconds)
- Write: 70 (7.0 seconds)
- Device Statistics (GP Log 0x04)
- Page Offset Size Value Flags Description
- 0x01 ===== = = === == General Statistics (rev 1) ==
- 0x01 0x008 4 140 -D- Lifetime Power-On Resets
- 0x01 0x010 4 29919 -D- Power-on Hours
- 0x01 0x018 6 113363338767 -D- Logical Sectors Written
- 0x01 0x020 6 996091244 -D- Number of Write Commands
- 0x01 0x028 6 1241655761559 -D- Logical Sectors Read
- 0x01 0x030 6 2734995911 -D- Number of Read Commands
- 0x01 0x038 6 334217600 -D- Date and Time TimeStamp
- 0x01 0x048 2 2522 ND- Workload Utilization
- 0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
- 0x03 0x008 4 23801 -D- Spindle Motor Power-on Hours
- 0x03 0x010 4 23616 -D- Head Flying Hours
- 0x03 0x018 4 3684 -D- Head Load Events
- 0x03 0x020 4 200 ND- Number of Reallocated Logical Sectors
- 0x03 0x028 4 0 -D- Read Recovery Attempts
- 0x03 0x030 4 0 -D- Number of Mechanical Start Failures
- 0x03 0x038 4 0 -D- Number of Realloc. Candidate Logical Sectors
- 0x03 0x040 4 62 -D- Number of High Priority Unload Events
- 0x04 ===== = = === == General Errors Statistics (rev 1) ==
- 0x04 0x008 4 0 -D- Number of Reported Uncorrectable Errors
- 0x04 0x010 4 2 -D- Resets Between Cmd Acceptance and Completion
- 0x05 ===== = = === == Temperature Statistics (rev 1) ==
- 0x05 0x008 1 23 -D- Current Temperature
- 0x05 0x010 1 25 -D- Average Short Term Temperature
- 0x05 0x018 1 29 -D- Average Long Term Temperature
- 0x05 0x020 1 51 -D- Highest Temperature
- 0x05 0x028 1 13 -D- Lowest Temperature
- 0x05 0x030 1 45 -D- Highest Average Short Term Temperature
- 0x05 0x038 1 23 -D- Lowest Average Short Term Temperature
- 0x05 0x040 1 38 -D- Highest Average Long Term Temperature
- 0x05 0x048 1 27 -D- Lowest Average Long Term Temperature
- 0x05 0x050 4 0 -D- Time in Over-Temperature
- 0x05 0x058 1 60 -D- Specified Maximum Operating Temperature
- 0x05 0x060 4 0 -D- Time in Under-Temperature
- 0x05 0x068 1 0 -D- Specified Minimum Operating Temperature
- 0x06 ===== = = === == Transport Statistics (rev 1) ==
- 0x06 0x008 4 610 -D- Number of Hardware Resets
- 0x06 0x010 4 313 -D- Number of ASR Events
- 0x06 0x018 4 0 -D- Number of Interface CRC Errors
- |||_ C monitored condition met
- ||__ D supports DSN
- |___ N normalized value
- Pending Defects log (GP Log 0x0c) not supported
- SATA Phy Event Counters (GP Log 0x11)
- ID Size Value Description
- 0x0001 2 0 Command failed due to ICRC error
- 0x0002 2 0 R_ERR response for data FIS
- 0x0003 2 0 R_ERR response for device-to-host data FIS
- 0x0004 2 0 R_ERR response for host-to-device data FIS
- 0x0005 2 0 R_ERR response for non-data FIS
- 0x0006 2 0 R_ERR response for device-to-host non-data FIS
- 0x0007 2 0 R_ERR response for host-to-device non-data FIS
- 0x0008 2 0 Device-to-host non-data FIS retries
- 0x0009 2 19 Transition from drive PhyRdy to drive PhyNRdy
- 0x000a 2 41 Device-to-host register FISes sent due to a COMRESET
- 0x000b 2 0 CRC errors within host-to-device FIS
- 0x000d 2 0 Non-CRC errors within host-to-device FIS
- 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
- 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
- 0x8000 4 0 Vendor specific
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement