HELLO! BOOT0 is starting!
boot0 version : 4.0.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V1.3
the chip id is 0x00000081
the chip id is 0x00000081
the chip id is 0x00000081
the chip id is 0x00000081
the chip id is 0x00000081
the gpio type set is 0x00000000
READ DQS LCDL = 00212122
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK = 576 MHz
DRAM zq value: 003b3bfb
DRAM dram para1: 10f40400
DRAM dram para2: 00000000
DRAM workmode1: 000009f4
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 2
card no is 2
sdcard 2 line count 8
[mmc]: mmc driver ver 2015-04-13 16:07:39
[mmc]: ***Try SD card 2***
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 send if cond failed
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 send app cmd failed
[mmc]: ***Try MMC card 2***
[mmc]: mmc re-update_phase
[mmc]: mmc re-update_phase
[mmc]: mmc re-update_phase
[mmc]: MMC ver 4.5
[mmc]: SD/MMC Card: 8bit, capacity: 7393MB
[mmc]: vendor: Man 00880103 Snr 35bedf0a
[mmc]: product: NCard
[mmc]: revision: 2.0
[mmc]: ***SD/MMC 2 init OK!!!***
sdcard 2 init ok
The size of uboot is 000dc000.
sum=4afa631c
src_sum=4afa631c
set_mmc_para,sdly 50M 0
set_mmc_para,sdly 25M 0
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
SUNXI_NORMAL_MODE
[      0.292]e mode

U-Boot 2011.09-rc1-00003-g9c79696 (Apr 16 2015 - 20:12:04) Allwinner Technology

[      0.301]version: 1.1.0
normal mode
[      0.308]pmbus:   ready
not set main pmu id
axp_probe error
gpio value=0x0
cpux freq run low
[      0.348]PMU: pll1 1008 Mhz,PLL6=600 Mhz
AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[      0.379]DRAM:  1 GiB
relocation Offset is: 35af7000
[recovery] no use
[box standby] read rtc = 0x0
[box standby] first start, so go to standby
BOOT_STANDBY_RUN_ADDR:0x40000
SRAM_A2_SIZE:0xc000
SCRIPT_ADDR:0x44000000
[box standby] script addr=0x44000000, length = 0xc000
[box standby] init_cpus
[box standby] CPU0 go to WFI