API tools faq
paste
Guest User

Boot, Suspend , Resume, Suspend, Freeze

a guest
Oct 6th, 2019
73
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 50.05 KB | None | 0 0
raw download clone embed print report
  1. GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
  2. TE: 91625
  3.  
  4. BL2 Built : 20:32:17, Sep 8 2017.
  5. gxl g6296b83 - xiaobo.gu@droid12
  6.  
  7. set vcck to 1120 mv
  8. set vddee to 1000 mv
  9. Board ID = 2
  10. CPU clk: 1200MHz
  11. DQS-corr enabled
  12. DDR scramble enabled
  13. DDR3 chl: Rank0+1 @ 792MHz - PASS
  14. Rank0: 1024MB(auto)-2T-11
  15. Rank1: 1024MB(auto)-2T-11
  16. DataBus test pass!
  17. AddrBus test pass!
  18. -s
  19. Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
  20. New fip structure!
  21. Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
  22. Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002c600
  23. Load bl33 from eMMC, src: 0x00050200, des: 0x01000000, size: 0x00066000
  24. NOTICE: BL3-1: v1.0(release):a625749
  25. NOTICE: BL3-1: Built : 11:25:15, Aug 25 2017
  26. [BL31]: GXL CPU setup!
  27. NOTICE: BL31: BL33 decompress pass
  28. mpu_config_enable:ok
  29. [Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
  30. OPS=0x82
  31. 67 27 70 53 aa ae 92 dd ff 8e 83 75 [0.317402 Inits done]
  32. secure task start!
  33. high task start!
  34. low task start!
  35. ERROR: Error initializing runtime service opteed_fast
  36.  
  37.  
  38. U-Boot 2015.01 (Oct 24 2017 - 20:30:44)
  39.  
  40. DRAM: 2 GiB
  41. Relocation Offset is: 76eb2000
  42. register usb cfg[0][1] = 0000000077f59c58
  43. [CANVAS]canvas init
  44. boot_device_flag : 1
  45. Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
  46. init bus_cycle=6, bus_timing=7, system=5.0ns
  47. reset failed
  48. get_chip_type and ret:fffffffe
  49. get_chip_type and ret:fffffffe
  50. chip detect failed and ret:fffffffe
  51. nandphy_init failed and ret=0xfffffff1
  52. MMC: aml_priv->desc_buf = 0x0000000073eb26b0
  53. aml_priv->desc_buf = 0x0000000073eb49d0
  54. SDIO Port B: 0, SDIO Port C: 1
  55. emmc/sd response timeout, cmd8, status=0x1ff2800
  56. emmc/sd response timeout, cmd55, status=0x1ff2800
  57. init_part() 293: PART_TYPE_AML
  58. [mmc_init] mmc init success
  59. dtb magic 5f4c4d41
  60. Amlogic multi-dtb tool
  61. Multi dtb detected
  62. Multi dtb tool version: v2 .
  63. Support 2 dtbs.
  64. aml_dt soc: gxl platform: p212 variant: 2g
  65. dtb 0 soc: gxl plat: p212 vari: 1g
  66. dtb 1 soc: gxl plat: p212 vari: 2g
  67. Find match dtb: 1
  68. start dts,buffer=0000000073eb7200,dt_addr=0000000073ec2200
  69. Amlogic multi-dtb tool
  70. Multi dtb detected
  71. Multi dtb tool version: v2 .
  72. Support 2 dtbs.
  73. aml_dt soc: gxl platform: p212 variant: 2g
  74. dtb 0 soc: gxl plat: p212 vari: 1g
  75. dtb 1 soc: gxl plat: p212 vari: 2g
  76. Find match dtb: 1
  77. parts: 10
  78. 00: logo 0000000002000000 1
  79. 01: recovery 0000000002000000 1
  80. 02: rsv 0000000000800000 1
  81. 03: tee 0000000000800000 1
  82. 04: crypt 0000000002000000 1
  83. 05: misc 0000000002000000 1
  84. 06: boot 0000000002000000 1
  85. 07: system 0000000080000000 1
  86. 08: cache 0000000020000000 2
  87. 09: data ffffffffffffffff 4
  88. init_part() 293: PART_TYPE_AML
  89. eMMC/TSD partition table have been checked OK!
  90. check pattern success
  91. mmc env offset: 0x27400000
  92. In: serial
  93. Out: serial
  94. Err: serial
  95. reboot_mode=cold_boot
  96. [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
  97. _verify_dtb_checksum()-917: calc 92d51a0d, store 92d51a0d
  98. _verify_dtb_checksum()-917: calc 92d51a0d, store 92d51a0d
  99. dtb_read()-1039: total valid 2
  100. dtb_read()-1106: do nothing
  101. Amlogic multi-dtb tool
  102. Multi dtb detected
  103. Multi dtb tool version: v2 .
  104. Support 2 dtbs.
  105. aml_dt soc: gxl platform: p212 variant: 2g
  106. dtb 0 soc: gxl plat: p212 vari: 1g
  107. dtb 1 soc: gxl plat: p212 vari: 2g
  108. Find match dtb: 1
  109. vpu: clk_level in dts: 7
  110. vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
  111. vpu: vpu_clk_gate_init_off
  112. vpp: vpp_init
  113. hpd_state=1
  114. [2160p60hz] is invalid for cvbs.
  115. set hdmitx VIC = 97
  116. config HPLL = 3712500
  117. HPLL: 0xc000029a
  118. config HPLL done
  119. j = 6 vid_clk_div = 1
  120. hdmitx: set enc for VIC: 353
  121. HDMITX-DWC addr=0x10004006 rd_data=0x40
  122. Error: HDMITX-DWC exp_data=0xff mask=0x9f
  123. rx version is 2.0 div=40
  124. hdmtix: set audio
  125. hdmitx phy setting done
  126. Net: dwmac.c9410000amlkey_init() enter!
  127. [EFUSE_MSG]keynum is 4
  128. [BL31]: tee size: 0
  129. [BL31]: tee size: 0
  130.  
  131. Start read misc partition datas!
  132. info->attemp_times = 0
  133. info->active_slot = 0
  134. info->slot_info[0].bootable = 1
  135. info->slot_info[0].online = 1
  136. info->slot_info[1].bootable = 0
  137. info->slot_info[1].online = 0
  138. info->attemp_times = 0
  139. attemp_times = 0
  140. active slot = 0
  141. wipe_data=successful
  142. wipe_cache=successful
  143. upgrade_step=2
  144. [OSD]load fb addr from dts
  145. [OSD]fb_addr for logo: 0x7f851000
  146. [OSD]load fb addr from dts
  147. [OSD]fb_addr for logo: 0x7f851000
  148. [CANVAS]addr=0x7f851000 width=3840, height=2160
  149. amlkey_init() enter!
  150. amlkey_init() 71: already init!
  151. [EFUSE_MSG]keynum is 4
  152. [BL31]: tee size: 0
  153. [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
  154. [BL31]: tee size: 0
  155. [BL31]: tee size: 0
  156. [BL31]: tee size: 0
  157. [BL31]: tee size: 0
  158. [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
  159. gpio: pin GPIOAO_2 (gpio 102) value is 1
  160. InUsbBurn
  161. noSof
  162. Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
  163. card in
  164. init_part() 278: PART_TYPE_DOS
  165. [mmc_init] mmc init success
  166. Device: SDIO Port B
  167. Manufacturer ID: 3
  168. OEM: 5344
  169. Name: SL16G
  170. Tran Speed: 50000000
  171. Rd Block Len: 512
  172. SD version 3.0
  173. High Capacity: Yes
  174. Capacity: 14.8 GiB
  175. mmc clock: 40000000
  176. Bus Width: 4-bit
  177. reading kernel.img
  178. 8656896 bytes read in 473 ms (17.5 MiB/s)
  179. reading dtb.img
  180. 79872 bytes read in 7 ms (10.9 MiB/s)
  181. sd dtb.img loaded
  182. ee_gate_off ...
  183. ## Booting Android Image at 0x01080000 ...
  184. reloc_addr =73f37450
  185. copy done
  186. load dtb from 0x1000000 ......
  187. Amlogic multi-dtb tool
  188. Multi dtb detected
  189. Multi dtb tool version: v2 .
  190. Support 2 dtbs.
  191. aml_dt soc: gxl platform: p212 variant: 2g
  192. dtb 0 soc: gxl plat: p212 vari: 1g
  193. dtb 1 soc: gxl plat: p212 vari: 2g
  194. Find match dtb: 1
  195. Uncompressing Kernel Image ... OK
  196. kernel loaded at 0x01080000, end = 0x01d28378
  197. Loading Ramdisk to 73c3a000, end 73ea0039 ... OK
  198. Loading Device Tree to 000000001fff3000, end 000000001ffff418 ... OK
  199. fdt_instaboot: no instaboot image
  200.  
  201. Starting kernel ...
  202.  
  203. uboot time: 2848560 us
  204. [ 0.000000@0] Initializing cgroup subsys cpu
  205. [ 0.000000@0] Linux version 3.14.29 (root@source) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP Tue Aug 21 14:02:31 EEST 2018
  206. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  207. [ 0.000000@0] no prop version_code
  208. [ 0.000000@0] bootconsole [earlycon0] enabled
  209. [ 0.000000@0] fdt Reserved memory table:
  210. [ 0.000000@0] linux,meson-fb: 0x000000007e000000 - 0x0000000080000000 (32 MiB)
  211. [ 0.000000@0] linux,di: 0x000000007c200000 - 0x000000007e000000 (30 MiB)
  212. [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007c200000, size 30 MiB
  213. [ 0.000000@0] linux,ion-dev: 0x0000000079200000 - 0x000000007c200000 (48 MiB)
  214. [ 0.000000@0] linux,ppmgr: 0x0000000079200000 - 0x0000000079200000 (0 MiB)
  215. [ 0.000000@0] linux,codec_mm_cma: 0x0000000067c00000 - 0x0000000073c00000 (192 MiB)
  216. [ 0.000000@0] linux,picdec: 0x0000000079200000 - 0x0000000079200000 (0 MiB)
  217. [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
  218. [ 0.000000@0] linux,codec_mm_reserved: 0x0000000075100000 - 0x0000000079200000 (65 MiB)
  219. [ 0.000000@0] fdt Reserved memory total: 371 MiB
  220. [ 0.000000@0] cma: Reserved 12 MiB at 74400000
  221. [ 0.000000@0] psci: probing function IDs from device-tree
  222. [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc0750a1000 s17344 r8192 d23616 u49152
  223. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 505748
  224. [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,2160p60hz maxcpus=4 vout=2160p60hz,enable hdmimode=2160p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=68:1d:ef:01:82:a8 androidboot.mac=68:1d:ef:01:82:a8 androidboot.slot_suffix=_a bootfromsd console=tty0 systemd.show_status=auto
  225. [ 0.000000@0] logo: osd1
  226. [ 0.000000@0] logo: loaded
  227. [ 0.000000@0] logo: 0x3d800000
  228. [ 0.000000@0] logo: 2160p60hz
  229. [ 0.000000@0] vout_serve: 2160p60hz
  230. [ 0.000000@0] vout_serve: en: 1
  231. [ 0.000000@0] logo: get hdmimode: 2160p60hz
  232. [ 0.000000@0] logo: get cvbsmode: 576cvbs
  233. [ 0.000000@0] tv_vout: cvbs performance line = 0
  234. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  235. [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  236. [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  237. [ 0.000000@0] Memory: 1643124K/2059264K available (7847K kernel code, 888K rwdata, 3124K rodata, 1092K init, 2920K bss, 416140K reserved)
  238. [ 0.000000@0] Virtual kernel memory layout:
  239. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
  240. [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8042380000 ( 35 MB)
  241. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  242. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07e000000 ( 2016 MB)
  243. [ 0.000000@0] .init : 0xffffffc001b38000 - 0xffffffc001c493c0 ( 1093 kB)
  244. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001b37d54 ( 10976 kB)
  245. [ 0.000000@0] .data : 0xffffffc001c4a000 - 0xffffffc001d28378 ( 889 kB)
  246. [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01b36fff]
  247. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
  248. [ 0.000000@0] arch_multi_cluster:0
  249. [ 0.000000@0] Hierarchical RCU implementation.
  250. [ 0.000000@0] RCU debugfs-based tracing is enabled.
  251. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  252. [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
  253. [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
  254. [ 0.008245@0] meson_bc_timer: mclk->mux_reg =ffffff800000c990,mclk->reg =ffffff800000e994
  255. [ 0.016731@0] Console: colour dummy device 80x25
  256. [ 0.021087@0] console [tty0] enabled
  257. [ 0.024672@0] bootconsole [earlycon0] disabled
  258. domain-0 init dvfs: 4
  259. [ 0.000000@0] Initializing cgroup subsys cpu
  260. [ 0.000000@0] Linux version 3.14.29 (root@source) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP Tue Aug 21 14:02:31 EEST 2018
  261. [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
  262. [ 0.000000@0] no prop version_code
  263. [ 0.000000@0] bootconsole [earlycon0] enabled
  264. [ 0.000000@0] fdt Reserved memory table:
  265. [ 0.000000@0] linux,meson-fb: 0x000000007e000000 - 0x0000000080000000 (32 MiB)
  266. [ 0.000000@0] linux,di: 0x000000007c200000 - 0x000000007e000000 (30 MiB)
  267. [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007c200000, size 30 MiB
  268. [ 0.000000@0] linux,ion-dev: 0x0000000079200000 - 0x000000007c200000 (48 MiB)
  269. [ 0.000000@0] linux,ppmgr: 0x0000000079200000 - 0x0000000079200000 (0 MiB)
  270. [ 0.000000@0] linux,codec_mm_cma: 0x0000000067c00000 - 0x0000000073c00000 (192 MiB)
  271. [ 0.000000@0] linux,picdec: 0x0000000079200000 - 0x0000000079200000 (0 MiB)
  272. [ 0.000000@0] Reserved memory: incorrect alignment of CMA region
  273. [ 0.000000@0] linux,codec_mm_reserved: 0x0000000075100000 - 0x0000000079200000 (65 MiB)
  274. [ 0.000000@0] fdt Reserved memory total: 371 MiB
  275. [ 0.000000@0] cma: Reserved 12 MiB at 74400000
  276. [ 0.000000@0] psci: probing function IDs from device-tree
  277. [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc0750a1000 s17344 r8192 d23616 u49152
  278. [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 505748
  279. [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,2160p60hz maxcpus=4 vout=2160p60hz,enable hdmimode=2160p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=68:1d:ef:01:82:a8 androidboot.mac=68:1d:ef:01:82:a8 androidboot.slot_suffix=_a bootfromsd console=tty0 systemd.show_status=auto
  280. [ 0.000000@0] logo: osd1
  281. [ 0.000000@0] logo: loaded
  282. [ 0.000000@0] logo: 0x3d800000
  283. [ 0.000000@0] logo: 2160p60hz
  284. [ 0.000000@0] vout_serve: 2160p60hz
  285. [ 0.000000@0] vout_serve: en: 1
  286. [ 0.000000@0] logo: get hdmimode: 2160p60hz
  287. [ 0.000000@0] logo: get cvbsmode: 576cvbs
  288. [ 0.000000@0] tv_vout: cvbs performance line = 0
  289. [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
  290. [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  291. [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  292. [ 0.000000@0] Memory: 1643124K/2059264K available (7847K kernel code, 888K rwdata, 3124K rodata, 1092K init, 2920K bss, 416140K reserved)
  293. [ 0.000000@0] Virtual kernel memory layout:
  294. [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB)
  295. [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8042380000 ( 35 MB)
  296. [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
  297. [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc07e000000 ( 2016 MB)
  298. [ 0.000000@0] .init : 0xffffffc001b38000 - 0xffffffc001c493c0 ( 1093 kB)
  299. [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001b37d54 ( 10976 kB)
  300. [ 0.000000@0] .data : 0xffffffc001c4a000 - 0xffffffc001d28378 ( 889 kB)
  301. [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01b36fff]
  302. [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=4, Nodes=1
  303. [ 0.000000@0] arch_multi_cluster:0
  304. [ 0.000000@0] Hierarchical RCU implementation.
  305. [ 0.000000@0] RCU debugfs-based tracing is enabled.
  306. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
  307. [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys).
  308. [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
  309. [ 0.008245@0] meson_bc_timer: mclk->mux_reg =ffffff800000c990,mclk->reg =ffffff800000e994
  310. [ 0.016731@0] Console: colour dummy device 80x25
  311. [ 0.021087@0] console [tty0] enabled
  312. [ 0.024672@0] bootconsole [earlycon0] disabled
  313. [ 0.029151@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
  314. [ 0.029168@0] pid_max: default: 32768 minimum: 301
  315. [ 0.029291@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  316. [ 0.029303@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  317. [ 0.031242@0] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
  318. [ 0.031261@0] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
  319. [ 0.031274@0] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
  320. [ 0.031286@0] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
  321. [ 0.033983@0] ftrace: allocating 26731 entries in 105 pages
  322. [ 0.060267@0] /cpus/cpu@0: Missing clock-frequency property
  323. [ 0.060291@0] /cpus/cpu@1: Missing clock-frequency property
  324. [ 0.060304@0] /cpus/cpu@2: Missing clock-frequency property
  325. [ 0.060315@0] /cpus/cpu@3: Missing clock-frequency property
  326. [ 0.061821@0] Meson chip version = RevB (21:B - 82:0)
  327. [ 0.062222@1] CPU1: Booted secondary processor
  328. [ 0.062560@2] CPU2: Booted secondary processor
  329. [ 0.062864@3] CPU3: Booted secondary processor
  330. [ 0.062926@0] Brought up 4 CPUs
  331. [ 0.062954@0] SMP: Total of 4 processors activated.
  332. [ 0.063414@0] devtmpfs: initialized
  333. [ 0.070268@0] instabooting: 0
  334. [ 0.076617@0] pinctrl core: initialized pinctrl subsystem
  335. [ 0.077155@0] regulator-dummy: no parameters
  336. [ 0.077758@0] NET: Registered protocol family 16
  337. [ 0.080154@0] aml_vdac_init: module init
  338. [ 0.080292@0] register canvas platform driver
  339. [ 0.080359@0] register rdma platform driver
  340. [ 0.081877@0] vdso: 2 pages (1 code, 1 data) at base ffffffc001c54000
  341. [ 0.082388@0] DMA: preallocated 1024 KiB pool for atomic allocations
  342. [ 0.083316@0] software IO TLB [mem 0x64800000-0x64c00000] (4MB) mapped at [ffffffc064800000-ffffffc064bfffff]
  343. [ 0.083714@0] aml_i2c version: 20140813
  344. [ 0.083905@0] i2c-core: driver [pmu4] using legacy resume method
  345. [ 0.083972@0] codec_mm:codec_mm_module_init
  346. [ 0.084235@0] gxbb_mpll_clk: register mpll_clk_out0 success done
  347. [ 0.084250@0] gxbb_mpll_clk: register mpll_clk_out1 success done
  348. [ 0.084262@0] gxbb_mpll_clk: register mpll_clk_out2 success done
  349. [ 0.084447@0] clk_sys: register PLL sys_pll success done
  350. [ 0.084467@0] gxl_clk: [ xtal ] ->clockrate: 24000000Hz
  351. [ 0.084477@0] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz
  352. [ 0.084486@0] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz
  353. [ 0.084496@0] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz
  354. [ 0.084505@0] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz
  355. [ 0.084515@0] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz
  356. [ 0.084524@0] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz
  357. [ 0.084533@0] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz
  358. [ 0.084542@0] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz
  359. [ 0.084573@0] gxl_clk: clock initialization complete
  360. [ 0.084797@0] clkmsr: Gxl msr_clk_reg0=ffffff800011c75c,msr_clk_reg2=ffffff800011e764
  361. [ 0.086820@0] aml_iomap: amlogic iomap probe done
  362. [ 0.087337@0] pinmux-gxl c1109880.pinmux: Init pinux probe!
  363. [ 0.088131@0] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
  364. [ 0.088571@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xc0)
  365. [ 0.088598@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xc0)
  366. [ 0.088739@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xc0)
  367. [ 0.088761@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xc0)
  368. [ 0.092760@0] codec_mm has 2 memory regions
  369. [ 0.092806@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
  370. [ 0.092824@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
  371. [ 0.092921@0] codec_mm has 2 memory regions
  372. [ 0.092939@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok
  373. [ 0.092956@0] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok
  374. [ 0.094391@0] vpu: driver version: v03
  375. [ 0.094426@0] vpu: load vpu_clk: 666667000Hz(7)
  376. [ 0.094512@0] vpu: vpu_probe OK
  377. [ 0.095745@0] tv_vout: tvout_probe
  378. [ 0.095764@0] tv_vout: chrdev devno 266338304 for disp
  379. [ 0.095773@0] vout_notify: vout_register_server
  380. [ 0.095781@0] tv_vout: register tv module server ok
  381. [ 0.095994@0] tv_vout: create cdev tv
  382. [ 0.096006@0] tv_vout: tvout_probe OK
  383. [ 0.096485@0] canvas_probe reg=00000000c8838000,size=400
  384. [ 0.096510@0] canvas maped reg_base =ffffff800013e000
  385. [ 0.100099@0] rdma_probe
  386. [ 0.332654@0] bio: create slab <bio-0> at 0
  387. [ 0.333460@0] SCSI subsystem initialized
  388. [ 0.333942@0] usbcore: registered new interface driver usbfs
  389. [ 0.334031@0] usbcore: registered new interface driver hub
  390. [ 0.334141@0] usbcore: registered new device driver usb
  391. [ 0.334813@0] i2c-gpio i2c_gpio.37: using pins 172 (SDA) and 173 (SCL)
  392. [ 0.334932@0] Linux video capture interface: v2.00
  393. [ 0.335049@0] pps_core: LinuxPPS API ver. 1 registered
  394. [ 0.335059@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  395. [ 0.335119@0] PTP clock support registered
  396. [ 0.335478@0] hdmitx: system: amhdmitx_init
  397. [ 0.335489@0] hdmitx: system: Ver: 2014May6
  398. [ 0.335651@0] hdmitx: system: amhdmitx_probe
  399. [ 0.335943@0] hdmitx: system: not find match init-data
  400. [ 0.335954@0] hdmitx: system: not find match pwr-ctl
  401. [ 0.335964@0] hdmitx hpd irq = 89
  402. [ 0.336474@0] hdmitx20: Mapped PHY: 0xc0800000
  403. [ 0.336492@0] hdmitx20: Mapped PHY: 0xc1104400
  404. [ 0.336513@0] hdmitx20: Mapped PHY: 0xc8100000
  405. [ 0.336523@0] hdmitx20: Mapped PHY: 0xc8834000
  406. [ 0.336532@0] hdmitx20: Mapped PHY: 0xc883a000
  407. [ 0.336540@0] hdmitx20: Mapped PHY: 0xc883c000
  408. [ 0.336555@0] hdmitx20: Mapped PHY: 0xd0100000
  409. [ 0.336564@0] hdmitx20: Mapped PHY: 0xda83a000
  410. [ 0.336581@0] hdmitx: alread display in uboot 0x861
  411. [ 0.336624@0] avmute set to 1
  412. [ 0.337021@0] tv_vout: tv_set_current_vmode[919]fps_target_mode=32
  413. [ 0.337037@0] tv_vout: mode is 32,sync_duration_den=1,sync_duration_num=60
  414. [ 0.337055@0] tv_vout: already display in uboot
  415. [ 0.337064@0] vout_serve: vinfo mode is: 2160p60hz
  416. [ 0.337073@0] vout_serve: init mode 2160p60hz
  417. [ 0.337298@0] vout_serve: create_vout_fops OK
  418. [ 0.337308@0] vout_serve: create vout attribute OK
  419. [ 0.337316@0] vout_serve: meson_vout_probe OK
  420. [ 0.337479@0] logo: logo_init
  421. [ 0.337723@0] osd_rdma: osd_rdma_init: rdma_table p=0x74501000,op=0x74501000 , v=0xffffff8000171000
  422. [ 0.337755@0] rdma_register, rdma_table_addr ffffff8000177000 rdma_table_addr_phy 74502000 reg_buf ffffffc000219000
  423. [ 0.337770@0] rdma_register success, handle 1 table_size 4096
  424. [ 0.337779@0] osd_rdma: osd_rdma_init:osd reset rdma handle = 1.
  425. [ 0.337808@0] rdma_register, rdma_table_addr ffffff8000179000 rdma_table_addr_phy 74503000 reg_buf ffffffc00020e000
  426. [ 0.337822@0] rdma_register success, handle 2 table_size 4096
  427. [ 0.337831@0] osd_rdma: osd_rdma_init:osd rdma handle = 2.
  428. [ 0.337972@0] Advanced Linux Sound Architecture Driver Initialized.
  429. [ 0.340229@0] Switched to clocksource arch_sys_counter
  430. [ 0.343667@0] hdmitx: system: irq 2
  431. [ 0.358757@0] NET: Registered protocol family 2
  432. [ 0.359237@0] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  433. [ 0.359360@0] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  434. [ 0.359607@0] TCP: Hash tables configured (established 16384 bind 16384)
  435. [ 0.359678@0] TCP: reno registered
  436. [ 0.359693@0] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  437. [ 0.359744@0] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  438. [ 0.359963@0] NET: Registered protocol family 1
  439. [ 0.360205@0] RPC: Registered named UNIX socket transport module.
  440. [ 0.360237@0] RPC: Registered udp transport module.
  441. [ 0.360245@0] RPC: Registered tcp transport module.
  442. [ 0.360254@0] RPC: Registered tcp NFSv4.1 backchannel transport module.
  443. [ 0.360446@0] aml_wifi wifi.32: [wifi_dev_probe] no power_on_pin2
  444. [ 0.360460@0] aml_wifi wifi.32: [wifi_dev_probe] set pwm as 32k output
  445. [ 0.360510@0] aml_wifi wifi.32: [wifi_dev_probe] dhd_static_buf setup
  446. [ 0.360569@0] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
  447. [ 0.360583@0] aml_wifi wifi.32: [wifi_dev_probe] interrupt_pin=241
  448. [ 0.360595@0] aml_wifi wifi.32: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
  449. [ 0.360608@0] aml_wifi wifi.32: [wifi_dev_probe] power_on_pin=240
  450. [ 0.360618@0] aml_wifi wifi.32: [wifi_dev_probe] clock_32k_pin=0
  451. [ 0.360922@0] aml_wifi wifi.32: [wifi_setup_dt] wifi_setup_dt
  452. [ 0.360962@0] aml_wifi wifi.32: [wifi_setup_dt] interrupt_pin(241)
  453. [ 0.360981@0] aml_wifi wifi.32: [wifi_setup_dt] power_on_pin(240)
  454. [ 0.361159@0] Unpacking initramfs...
  455. [ 0.390398@0] Freeing initrd memory: 2456K (ffffffc073c3a000 - ffffffc073ea0000)
  456. [ 0.393113@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
  457. [ 0.401215@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  458. [ 0.402528@0] NFS: Registering the id_resolver key type
  459. [ 0.402573@0] Key type id_resolver registered
  460. [ 0.402582@0] Key type id_legacy registered
  461. [ 0.402596@0] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  462. [ 0.403327@0] msgmni has been set to 3622
  463. [ 0.404302@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
  464. [ 0.404328@0] io scheduler noop registered (default)
  465. [ 0.404338@0] io scheduler deadline registered
  466. [ 0.404497@0] io scheduler cfq registered
  467. [ 0.405198@0] meson-rng c8834000.rng: hwrng registered
  468. [ 0.408230@0] loop: module loaded
  469. [ 0.409831@0] tun: Universal TUN/TAP device driver, 1.6
  470. [ 0.409852@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  471. [ 0.413808@0] libphy: stmmac: probed
  472. [ 0.413831@0] eth0: PHY ID 01814400 at 8 IRQ POLL (stmmac-0:08) active
  473. [ 0.414210@0] PPP generic driver version 2.4.2
  474. [ 0.414431@0] NET: Registered protocol family 24
  475. [ 0.414541@0] usbcore: registered new interface driver smsc95xx
  476. [ 0.414830@0] platform c9000000.dwc3: Driver dwc3 requests probe deferral
  477. [ 0.414940@0] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  478. [ 0.414965@0] ehci-h20ahb: H20AHB-EHCI Host Controller driver
  479. [ 0.415150@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  480. [ 0.415400@0] usbcore: registered new interface driver usb-storage
  481. [ 0.415605@0] usbcore: registered new interface driver usbserial
  482. [ 0.415682@0] usbcore: registered new interface driver usbserial_generic
  483. [ 0.415759@0] usbserial: USB Serial support registered for generic
  484. [ 0.415838@0] usbcore: registered new interface driver pl2303
  485. [ 0.415908@0] usbserial: USB Serial support registered for pl2303
  486. [ 0.416364@0] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff8000284000
  487. [ 0.416540@0] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
  488. [ 0.416565@0] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff8000286080
  489. [ 0.416838@0] mousedev: PS/2 mouse device common for all mice
  490. [ 0.417034@0] i2c /dev entries driver
  491. [ 0.417726@0] ledtrig-cpu: registered to indicate activity on CPUs
  492. [ 0.417876@0] hidraw: raw HID events driver (C) Jiri Kosina
  493. [ 0.419760@0] usbcore: registered new interface driver usbhid
  494. [ 0.419781@0] usbhid: USB HID core driver
  495. [ 0.420014@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80002884c0
  496. [ 0.420048@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart
  497. [ 0.420071@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200
  498. [ 1.815741@3] console [ttyS0] enabled
  499. [ 1.815849@0] hdmitx: plugin
  500. [ 1.822616@1] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff800028a4c0
  501. [ 1.829267@1] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart
  502. [ 1.840061@1] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0
  503. [ 1.847186@1] dwc_otg_driver_probe host only, not probe usb_otg!!!
  504. [ 1.853675@1] hdmitx: system: hdmitx_hdcp_init
  505. [ 1.858196@1] aml_vrtc rtc.31: rtc core: registered aml_vrtc as rtc0
  506. [ 1.865010@1] secmon has 1 memory regions
  507. [ 1.868002@1] secmon: share in base: 0xffffff80002aa000, share out base: 0xffffff80002ac000
  508. [ 1.871687@0] EDID Parser:
  509. [ 1.878950@1] secmon secmon.4: assigned reserved memory node linux,secmon ok
  510. [ 1.885916@1] secmon: probe done
  511. [ 1.889378@0] hdmitx: get dtd0 vic: 97
  512. [ 1.889456@1] storage: storage in base: 0xffffff8001700000
  513. [ 1.889457@1] storage: storage out base: 0xffffff8001780000
  514. [ 1.889459@1] storage: storage block base: 0xffffff8001800000
  515. [ 1.889460@1] storage: probe done!
  516. [ 1.889914@1] aml_sd_emmc_probe: line 3594
  517. [ 1.889918@1] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error
  518. [ 1.926385@0] hdmitx: get dtd1 vic: 95
  519. [ 1.930026@0] dump_dtd_info[1762]
  520. [ 1.933269@0] pixel_clock 8475
  521. [ 1.936281@0] h_active 1360
  522. [ 1.939041@0] h_blank 416
  523. [ 1.941633@0] v_active 768
  524. [ 1.944302@0] v_blank 30
  525. [ 1.946818@0] h_sync_offset 208
  526. [ 1.949909@0] h_sync 136
  527. [ 1.952414@0] v_sync_offset 22
  528. [ 1.955429@0] v_sync 5
  529. [ 1.957758@0] dump_dtd_info[1762]
  530. [ 1.961039@0] pixel_clock 7950
  531. [ 1.964068@0] h_active 1280
  532. [ 1.966814@0] h_blank 384
  533. [ 1.969401@0] v_active 768
  534. [ 1.972079@0] v_blank 30
  535. [ 1.974576@0] h_sync_offset 192
  536. [ 1.977681@0] h_sync 128
  537. [ 1.980196@0] v_sync_offset 20
  538. [ 1.983205@0] v_sync 7
  539. [ 1.985530@0] hdmitx: edid: find IEEEOUT
  540. [ 1.989414@0] hdmitx: edid: check sum valid
  541. [ 1.993555@0] hdmitx: edid: check sum valid
  542. [ 1.997725@0] hdmitx: update RX hdr info 4
  543. [ 1.997885@1] aml_sd_emmc_reg_init 1149
  544. [ 1.997960@1] get property: ocr_avail, value:0x00200080
  545. [ 1.997963@1] get property: f_min, value:300000
  546. [ 1.997965@1] get property: f_max, value:100000000
  547. [ 1.997969@1] get property: max_req_size, value:0x00020000
  548. [ 1.997976@1] get property: pinname, str:emmc
  549. [ 1.997981@1] get property: card_type, value:1
  550. [ 1.998003@1] get property: gpio_dat3, str:
  551. [ 1.998007@1] get property: hw_reset, str:
  552. [ 1.998043@1] emmc:pdata->caps = c0000d47
  553. [ 1.998050@1] emmc:pdata->caps2 = 18060
  554. [ 1.998053@1] emmc:pdata->pm_caps = 0
  555. [ 1.998067@1] storage 1, boot 1
  556. [ 1.998069@1] get_storage_dev return 1
  557. [ 2.040255@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  558. [ 2.040315@1] aml_sd_emmc_probe: line 3594
  559. [ 2.044644@1] aml_sd_emmc_reg_init 1149
  560. [ 2.044705@1] get property: ocr_avail, value:0x00200080
  561. [ 2.044708@1] get property: f_min, value:400000
  562. [ 2.044710@1] get property: f_max, value:100000000
  563. [ 2.044713@1] get property: max_req_size, value:0x00020000
  564. [ 2.044715@1] get property: irq_in, value:3
  565. [ 2.044718@1] get property: irq_out, value:5
  566. [ 2.044739@1] get property: gpio_cd, str:
  567. [ 2.044743@1] get property: pinname, str:sd
  568. [ 2.044746@1] get property: jtag_pin, str:
  569. [ 2.044750@1] get property: card_type, value:5
  570. [ 2.044755@1] get property: gpio_dat3, str:
  571. [ 2.044772@1] sd:pdata->caps = 7
  572. [ 2.044774@1] sd:pdata->caps2 = 0
  573. [ 2.044776@1] sd:pdata->pm_caps = 0
  574. [ 2.080402@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  575. [ 2.080439@1] aml_sd_emmc_probe: line 3594
  576. [ 2.080718@1] aml_sd_emmc_reg_init 1149
  577. [ 2.080799@1] get property: ocr_avail, value:0x00200080
  578. [ 2.080801@1] get property: f_min, value:400000
  579. [ 2.080804@1] get property: f_max, value:200000000
  580. [ 2.080807@1] get property: max_req_size, value:0x00020000
  581. [ 2.080813@1] get property: pinname, str:sdio
  582. [ 2.080817@1] get property: card_type, value:3
  583. [ 2.080861@1] sdio:pdata->caps = 7810f
  584. [ 2.080864@1] sdio:pdata->caps2 = 0
  585. [ 2.080867@1] sdio:pdata->pm_caps = 1
  586. [ 2.120241@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success!
  587. [ 2.120592@1] ion_dev has 1 memory regions
  588. [ 2.124579@1] fb: osd_init_module
  589. [ 2.124712@1] fb: viu vsync irq: 35
  590. [ 2.124720@1] meson-fb has 1 memory regions
  591. [ 2.124762@1] meson-fb meson-fb.16: assigned reserved memory node linux,meson-fb ok
  592. [ 2.124780@1] fb: osd_probe vinfo:ffffffc001cbdc68
  593. [ 2.124784@1] fb: init fbdev bpp is:32
  594. [ 2.257739@0] hdmitx: edid: check sum valid
  595. [ 2.257751@2] [aml_is_card_insert] card IN
  596. [ 2.265798@0] hdmitx: edid: check sum valid
  597. [ 2.265829@1] fb: set osd0 reverse as NONE
  598. [ 2.279906@1] fb: osd probe OK
  599. [ 2.280139@1] ge2d: ge2d_init_module
  600. [ 2.280884@1] ge2d: ge2d_dev major:243
  601. [ 2.284926@1] ge2d: ge2d clock is 400 MHZ
  602. [ 2.288546@1] ge2d: ge2d: pdev=ffffffc00026f000, irq=182, rstc=0xffffffc0643691c0, clk=ffffffc000225b00
  603. [ 2.297912@1] ge2d: mapped phy: 0xd0160000
  604. [ 2.301922@1] ge2d: ge2d start monitor
  605. [ 2.305674@3] ge2d: ge2d workqueue monitor start
  606. [ 2.306090@1] codec:Amlogic A/V streaming port init
  607. [ 2.307851@1] codec:get gate demux control ok ffffffc0003e1b40
  608. [ 2.307856@1] codec:get gate parser_top control ok ffffffc0003e1bc0
  609. [ 2.307860@1] codec:get gate vpu_intr control ok ffffffc0003e1c40
  610. [ 2.307865@1] codec:get gate vdec control ok ffffffc0003e1cc0
  611. [ 2.308792@1] codec:[tsync_pcr_init]init success.
  612. [ 2.308944@1] codec:amvideocap_probe,amvideocap
  613. [ 2.308949@1] codec:use cma buf.
  614. [ 2.310951@1] amvenc_avc_probe -- reserved memory config fail.
  615. [ 2.310955@1] amvenc_avc - cma memory pool size: 40 MB
  616. [ 2.310984@1] encode_wq_init.
  617. [ 2.310989@1] encode start monitor.
  618. [ 2.311115@1] encode workqueue monitor start.
  619. [ 2.312174@1] codec:vdec_request_irq ffffffc001630808, vsync
  620. [ 2.312431@1] codec:create_ge2d_work_queue video task ok
  621. [ 2.313017@1] rdma_register, rdma_table_addr ffffff80002f1000 rdma_table_addr_phy 74510000 reg_buf ffffffc0643b0000
  622. [ 2.313020@1] rdma_register success, handle 3 table_size 32768
  623. [ 2.313023@1] video_rdma:rdma_init video rdma handle = 3.
  624. [ 2.313030@1] codec:used fix clk for vdec clk source!
  625. [ 2.313037@1] codec:register clk_set_setting cpu[33]
  626. [ 2.313945@1] DI: di_module_init ok.
  627. [ 2.313952@1] DI: di_module_init: major 238
  628. [ 2.314192@1] DI: di_probe
  629. [ 2.314418@1] deinterlace has 1 memory regions
  630. [ 2.314476@1] deinterlace deinterlace.26: assigned reserved memory node linux,di ok
  631. [ 2.314480@1] DI-di_probe: get flag_cma error.
  632. [ 2.314507@1] di_irq:78,timerc_irq:38
  633. [ 2.314650@1] rdma_register, rdma_table_addr ffffff80002fa000 rdma_table_addr_phy 7450a000 reg_buf ffffffc063c0e000
  634. [ 2.314653@1] rdma_register success, handle 4 table_size 8192
  635. [ 2.314655@1] DI: di_probe allocate rdma channel 4.
  636. [ 2.314659@1] DI: DI hw version 2.
  637. [ 2.314672@1] 0x000000db:Y=db,U=0,V=0
  638. [ 2.314674@1] 0x000000dc:Y=dc,U=0,V=0
  639. [ 2.314676@1] 0x000000dd:Y=dd,U=0,V=0
  640. [ 2.314678@1] 0x000000de:Y=de,U=0,V=0
  641. [ 2.314680@1] 0x000000df:Y=df,U=0,V=0
  642. [ 2.314681@1] 0x000000e0:Y=e0,U=0,V=0
  643. [ 2.314683@1] 0x000000e1:Y=e1,U=0,V=0
  644. [ 2.314685@1] 0x000000e2:Y=e2,U=0,V=0
  645. [ 2.314687@1] 0x000000e3:Y=e3,U=0,V=0
  646. [ 2.314689@1] 0x000000f0:Y=f0,U=0,V=0
  647. [ 2.314693@1] 0x000000f1:Y=f1,U=0,V=0
  648. [ 2.314695@1] 0x000000f2:Y=f2,U=0,V=0
  649. [ 2.314696@1] 0x000000f3:Y=f3,U=0,V=0
  650. [ 2.314698@1] 0x000000f4:Y=f4,U=0,V=0
  651. [ 2.314700@1] 0x000000f5:Y=f5,U=0,V=0
  652. [ 2.314702@1] 0x000000f6:Y=f6,U=0,V=0
  653. [ 2.314705@1] 0x000000f7:Y=f7,U=0,V=0
  654. [ 2.314706@1] 0x000000f8:Y=f8,U=0,V=0
  655. [ 2.314708@1] 0x000000f9:Y=f9,U=0,V=0
  656. [ 2.314710@1] 0x000000fa:Y=fa,U=0,V=0
  657. [ 2.314712@1] 0x000000fb:Y=fb,U=0,V=0
  658. [ 2.314714@1] 0x000000fc:Y=fc,U=0,V=0
  659. [ 2.314901@1] DI: di_probe here.
  660. [ 2.315322@1] efusekeynum: 4
  661. [ 2.315333@1] efusekeyname: mac offset: 0 size: 6
  662. [ 2.315339@1] efusekeyname: mac_bt offset: 6 size: 6
  663. [ 2.315345@1] efusekeyname: mac_wifi offset: 12 size: 6
  664. [ 2.315351@1] efusekeyname: usid offset: 18 size: 16
  665. [ 2.315669@1] efuse efuse.10: probe OK!
  666. [ 2.316055@1] key unify config unifykey-num is 14
  667. [ 2.316110@1] key unify fact unifykey-num is 14
  668. [ 2.316114@1] aml_unifykeys_probe:1273=============unifykey_devno:ec00000
  669. [ 2.316395@1] 6unifykey: device unifykeys created ok
  670. [ 2.316524@1] 6aml_unifykeys_init done!
  671. [ 2.316527@1] PPMGRDRV: warn: ppmgr module init func called
  672. [ 2.316641@1] PPMGRDRV: err: ppmgr_driver_probe called
  673. [ 2.316646@1] ppmgr has 1 memory regions
  674. [ 2.316686@1] PPMGRDRV: info: ppmgr_dev major:235
  675. [ 2.316988@1] PPMGRDRV: info: ppmgr_probe done
  676. [ 2.317383@1] amlogic rfkill init
  677. [ 2.317461@1] enter bt_probe of_node
  678. [ 2.317481@1] not get gpio_en
  679. [ 2.359035@2] power on valid level is high
  680. [ 2.359036@2] normal card in
  681. [ 2.359083@0] hdmitx: edid: blk0 raw data
  682. [ 2.359122@0] 00ffffffffffff001e5548440100000001190103807944782aec6ba056479c25
  683. [ 2.359122@0] 10484a27cf000101010181408180818f8b000101a94008e80030f2705a80b058
  684. [ 2.359122@0] 8a00a05a0000001e04740030f2705a80b0588a00a05a0000001e000000fd0031
  685. [ 2.359122@0] 4c0f513c000a202020202020000000fc004752554e444947205548440a200124
  686. [ 2.359122@0]
  687. [ 2.359122@0]
  688. [ 2.359125@0] hdmitx: edid: blk1 raw data
  689. [ 2.359162@0] 02034d725760615f5e5d1f10222120140513041211020301060715162c570700
  690. [ 2.359162@0] 1707503f07c00907076d030c001000b03c20006001020367d85dc401778003e2
  691. [ 2.359162@0] 0f03e60604016e6e05e305e0001b2150a051001e30d0886504a05a0000001c0e
  692. [ 2.359162@0] 1f008051001e30c0804704a05a0000001c00000000000000000000000000005c
  693. [ 2.359162@0]
  694. [ 2.359162@0]
  695. [ 2.359192@0] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
  696. [ 2.359200@0] hdmitx: video: get current mode: 2160p60hz
  697. [ 2.359202@0] hdmitx: update rx hdr info 4
  698. [ 2.359203@0] hdmitx: update physcial size: 1210 680
  699. [ 2.359252@0] hdmitx: system: already init VIC = 0 Now VIC = 97
  700. [ 2.359258@0] hdmitx: rx has SCDC present indicator
  701. [ 2.361326@0] hdmirx version is 2.0
  702. [ 2.361329@0] hdmitx div40: 1
  703. [ 2.390239@0] hdmitx: system: set mode VIC 97 (cd0,cs0,pm1,vd0,1)
  704. [ 2.390243@0] hdmitx: system: set pll
  705. [ 2.390244@0] hdmitx: system: param->VIC:97
  706. [ 2.390247@0] hdmitx: set clk: VIC = 97 cd = 4 frac_rate = 0
  707. [ 2.390256@0] config HPLL = 5940000
  708. [ 2.390323@0] HPLL: 0x4000027b
  709. [ 2.390324@0] config HPLL done
  710. [ 2.390332@0] set_hpll_od3_clk_div[437] div = 6
  711. [ 2.390340@0] j = 7 vid_clk_div = 1
  712. [ 2.390350@0] hdmitx: set enc for VIC: 97
  713. [ 2.390366@0] hdmitx_set_hw[4955] set VIC = 97
  714. [ 2.394305@1] emmc: BKOPS_EN bit is not set
  715. [ 2.400554@1] emmc: trying cali 0-th time(s)
  716. [ 2.404095@1] emmc: delay[0]= 1600 padding= 2, bidx=1
  717. [ 2.404098@1] emmc: delay[1]= 1800 padding= 1, bidx=1
  718. [ 2.404100@1] emmc: delay[2]= 1400 padding= 3, bidx=1
  719. [ 2.404102@1] emmc: delay[3]= 1800 padding= 1, bidx=1
  720. [ 2.404105@1] emmc: delay[4]= 1800 padding= 1, bidx=1
  721. [ 2.404107@1] emmc: delay[5]= 1800 padding= 1, bidx=1
  722. [ 2.404109@1] emmc: delay[6]= 1800 padding= 1, bidx=1
  723. [ 2.404111@1] emmc: delay[7]= 1800 padding= 1, bidx=1
  724. [ 2.404113@1] emmc: calibration result @ 0: max(1800), min(1400)
  725. [ 2.404117@1] emmc: line_delay =0x201, max_cal_result =1800
  726. [ 2.404119@1] emmc: base_index_max 1, base_index_min 1
  727. [ 2.404125@1] emmc: clk 100000000 SDR mode tuning start
  728. [ 2.404389@1] emmc: rx_tuning_result[0] = 10
  729. [ 2.404634@1] emmc: rx_tuning_result[1] = 10
  730. [ 2.404876@1] emmc: rx_tuning_result[2] = 10
  731. [ 2.405117@1] emmc: rx_tuning_result[3] = 10
  732. [ 2.405359@1] emmc: rx_tuning_result[4] = 10
  733. [ 2.405602@1] emmc: rx_tuning_result[5] = 10
  734. [ 2.405869@1] emmc: rx_tuning_result[7] = 10
  735. [ 2.406109@1] emmc: rx_tuning_result[8] = 10
  736. [ 2.406355@1] emmc: rx_tuning_result[9] = 10
  737. [ 2.406357@1] emmc: best_win_start =7, best_win_size =9
  738. [ 2.406360@1] emmc: sd_emmc_regs->gclock=0x100024a,sd_emmc_regs->gadjust=0x12000
  739. [ 2.406364@1] emmc: gclock =0x100024a, gdelay=0x201, gadjust=0x12000
  740. [ 2.406455@1] emmc: support driver strength type 1
  741. [ 2.406498@1] emmc: try set sd/emmc to DDR mode
  742. [ 2.406502@1] emmc: try set sd/emmc to DDR mode
  743. [ 2.406580@1] emmc: new HS400 MMC card at address 0001
  744. [ 2.407123@1] emmc: clock 100000000, 8-bit-bus-width
  745. [ 2.407123@1]
  746. [ 2.407123@1] mmcblk0: emmc:0001 8WPD3R 7.28 GiB
  747. [ 2.407239@1] mmcblk0boot0: emmc:0001 8WPD3R partition 1 4.00 MiB
  748. [ 2.407350@1] mmcblk0boot1: emmc:0001 8WPD3R partition 2 4.00 MiB
  749. [ 2.407476@1] mmcblk0rpmb: emmc:0001 8WPD3R partition 3 512 KiB
  750. [ 2.408361@1] mmcblk0: unknown partition table
  751. [ 2.409115@1] [mmc_read_partition_tbl] mmc read partition OK!
  752. [ 2.409116@1] add_emmc_partition
  753. [ 2.409373@1] [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
  754. [ 2.409541@1] [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
  755. [ 2.409671@1] [mmcblk0p03] cache offset 0x000006c00000, size 0x000020000000
  756. [ 2.409804@1] [mmcblk0p04] env offset 0x000027400000, size 0x000000800000
  757. [ 2.409938@1] [mmcblk0p05] logo offset 0x000028400000, size 0x000002000000
  758. [ 2.410064@1] [mmcblk0p06] recovery offset 0x00002ac00000, size 0x000002000000
  759. [ 2.410212@1] [mmcblk0p07] rsv offset 0x00002d400000, size 0x000000800000
  760. [ 2.410451@1] [mmcblk0p08] tee offset 0x00002e400000, size 0x000000800000
  761. [ 2.410602@1] [mmcblk0p09] crypt offset 0x00002f400000, size 0x000002000000
  762. [ 2.410730@1] [mmcblk0p10] misc offset 0x000031c00000, size 0x000002000000
  763. [ 2.410874@1] [mmcblk0p11] boot offset 0x000034400000, size 0x000002000000
  764. [ 2.411000@1] [mmcblk0p12] system offset 0x000036c00000, size 0x000080000000
  765. [ 2.411152@1] [mmcblk0p13] data offset 0x0000b7400000, size 0x00011ac00000
  766. [ 2.411190@1] card key: card_blk_probe.
  767. [ 2.411196@1] emmc_key_init:527 emmc key lba_start:0x12020,lba_end:0x12220
  768. [ 2.411199@1] emmc key: emmc_key_init:552 ok.
  769. [ 2.414224@1] amlmmc_dtb_init: register dtb chardev
  770. [ 2.414225@1] calc 92d51a0d, store 92d51a0d
  771. [ 2.416925@1] calc 92d51a0d, store 92d51a0d
  772. [ 2.416929@1] total valid 2
  773. [ 2.417512@1] amlmmc_dtb_init: register dtb chardev OK
  774. [ 2.417512@1] Exit aml_emmc_partition_ops OK.
  775. [ 2.419664@1] mmcblk0boot1: unknown partition table
  776. [ 2.420697@1] mmcblk0boot0: unknown partition table
  777. [ 2.420982@1] clear_emmc_wait_flag
  778. [ 2.522241@0] hdmitx: system: PHY Setting Done
  779. [ 2.522252@0] hdmitx: system: irq 80000001
  780. [ 2.526255@0] Sink is HDMI device
  781. [ 2.526266@0] hdmitx: system: packet: can't get vendor data
  782. [ 2.526271@0] 2160p60hz 60 1
  783. [ 2.526275@0] 2160p60hz 60 1
  784. [ 2.526279@0] hdmtix: set audio
  785. [ 2.526288@0] hdmitx tx_aud_src = 0
  786. [ 2.526313@0] hdmitx: fs = 0, cd = 4, tmds_clk = 594000
  787. [ 2.526317@0] hdmitx aud_n_para = 6144
  788. [ 2.526334@0] hdmitx set channel status
  789. [ 2.526392@0] hdmtix: set audio
  790. [ 2.526401@0] hdmitx tx_aud_src = 0
  791. [ 2.526425@0] hdmitx: fs = 0, cd = 4, tmds_clk = 594000
  792. [ 2.526426@0] hdmitx aud_n_para = 6144
  793. [ 2.526443@0] hdmitx set channel status
  794. [ 2.526640@0] Start = 0x10000100 End = 0x100001ff
  795. [ 2.526651@0] [0x10000104]: 0x00000001
  796. [ 2.526845@0] [0x10000180]: 0x000000ff
  797. [ 2.526848@0] [0x10000181]: 0x000000ff
  798. [ 2.526850@0] [0x10000182]: 0x00000003
  799. [ 2.526853@0] [0x10000183]: 0x00000007
  800. [ 2.526856@0] [0x10000184]: 0x0000003f
  801. [ 2.526859@0] [0x10000185]: 0x00000002
  802. [ 2.526864@0] [0x10000187]: 0x000000ff
  803. [ 2.526866@0] [0x10000188]: 0x00000003
  804. [ 2.730472@0] audio_dsp: [dsp]register dsp to char divece(257)
  805. [ 2.731223@0] amaudio: amaudio: driver amaudio succuess!
  806. [ 2.731229@0] amlvid:err: amlvideo_init called
  807. [ 2.731230@0] amlvid:err: amlvideo_create_instance called
  808. [ 2.731233@0] amlvid:err: v4l2_dev.name=:amlvideo-000
  809. [ 2.731369@0] amlvideo-000: V4L2 device registered as video10
  810. [ 2.731820@0] [RX]-hdmirx: hdmirx_init.
  811. [ 2.731823@0] ESM HLD: Initializing...
  812. [ 2.731826@0] ESM HLD: Registering device range 'esm_rx'...
  813. [ 2.731833@0] ESM HLD: Device range 'esm_rx' has been registered.
  814. [ 2.731835@0] ESM HLD: Creating class /sys/class/elliptic_rx...
  815. [ 2.731892@0] ESM HLD: The class /sys/class/elliptic_rx has been created.
  816. [ 2.731893@0] ESM HLD: Creating device 'esm_rx'...
  817. [ 2.732046@0] ESM HLD: Device 'esm_rx' has been created.
  818. [ 2.732047@0] ESM HLD: Done initializing the HLD driver.
  819. [ 2.732049@0] module init
  820. [ 2.732206@0]
  821. [ 2.732206@0] VECM probe start
  822. [ 2.732485@0] aml_vecm_probe: ok
  823. [ 2.733084@0] saradc c1108680.saradc: initialized by kernel, clk_div=20
  824. [ 2.733095@0] saradc c1108680.saradc: calibration start:
  825. [ 2.733178@0] saradc c1108680.saradc: nominal=0, value=2
  826. [ 2.733262@0] saradc c1108680.saradc: nominal=256, value=264
  827. [ 2.733345@0] saradc c1108680.saradc: nominal=512, value=526
  828. [ 2.733429@0] saradc c1108680.saradc: nominal=768, value=787
  829. [ 2.733513@0] saradc c1108680.saradc: nominal=1023, value=1023
  830. [ 2.733516@0] saradc c1108680.saradc: calibration end: coef=4009
  831. [ 2.733691@0] remote: Driver init
  832. [ 2.733758@0] remote: platform_data g_remote_ao_offset=580
  833. [ 2.733760@0] remote: platform_data irq =228
  834. [ 2.733789@0] remote: set drvdata completed
  835. [ 2.733801@0] remote: device_create_file completed
  836. [ 2.734135@0] input: aml_keypad as /devices/meson-remote.12/input/input0
  837. [ 2.734461@0] remote: input_register_device completed
  838. [ 2.734538@0] remote: set_remote_mode[74]
  839. [ 2.734571@0] remote: remote config major:231
  840. [ 2.734782@0] remote: physical address:0x63d3e000
  841. [ 2.735178@0] gpio-key gpio_keypad.47: gpio_key: 0 name(power) pin()
  842. [ 2.735183@0] gpio-key gpio_keypad.47: amlogic_gpio_name_map_num pin 0!::
  843. [ 2.735203@0] gpio-key gpio_keypad.47: gpio_key: 0 power(147)
  844. [ 2.735243@0] gpio-key gpio_keypad.47: start setup_timer
  845. [ 2.735251@0] gpio-key gpio_keypad.47: power key(116) registed.
  846. [ 2.735455@0] input: gpio_keypad as /devices/gpio_keypad.47/input/input1
  847. [ 2.735629@0] gpio-key gpio_keypad.47: gpio keypad register input device completed.
  848. [ 2.735640@0] input input1: gpio keypad major:230
  849. [ 2.736017@0] cpuinfo: probe done
  850. [ 2.736890@0] input: cec_input as /devices/virtual/input/input2
  851. [ 2.737217@0] cectx aocec: aml_cec_probe(): no hdmirx reg resource
  852. [ 2.737220@0] cectx aocec: aml_cec_probe(): no hhi reg resource
  853. [ 2.737342@0] cectx aocec: aml_cec_probe(): can't find hdmirx
  854. [ 2.738464@0] cec: wake up flag:0
  855. [ 2.740181@0] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe
  856. [ 2.742333@0] aml_pcm_dai: pcm mode detection =1
  857. [ 2.830254@0] input input1: key 116 up
  858. [ 2.906255@0] hdmitx20: rx scrambler status
  859. [ 2.950450@0] aml_snd_card: headphone detection disable=1
  860. [ 2.950962@0] aml_snd_m8_card aml_m8_snd.46: T9015-audio-hifi <-> I2S.39 mapping ok
  861. [ 2.951388@0] aml_snd_m8_card aml_m8_snd.46: dit-hifi <-> SPDIF.40 mapping ok
  862. [ 2.951431@0] aml_pcm: enter aml_pcm_new dai->name: PCM.41 dai->id: 0
  863. [ 2.951507@0] aml_snd_m8_card aml_m8_snd.46: pcm2bt-pcm <-> PCM.41 mapping ok
  864. [ 2.951531@0] aml_snd_m8_card aml_m8_snd.46: ASoC: no source widget found for LOUTL
  865. [ 2.951536@0] aml_snd_m8_card aml_m8_snd.46: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
  866. [ 2.951541@0] aml_snd_m8_card aml_m8_snd.46: ASoC: no source widget found for LOUTR
  867. [ 2.951544@0] aml_snd_m8_card aml_m8_snd.46: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
  868. [ 3.060254@0] aml_snd_card: audio use jtag pinmux as i2s output, read val =0
  869. [ 3.061011@0] TCP: cubic registered
  870. [ 3.061630@0] NET: Registered protocol family 10
  871. [ 3.062530@0] NET: Registered protocol family 17
  872. [ 3.062600@0] Key type dns_resolver registered
  873. [ 3.064173@0] Registering SWP/SWPB emulation handler
  874. [ & ▒▒▒▒▒▒] regulator-dummy: disabling
  875. [ 3.716859@3] sd: new high speed SDHC card at address aaaa
  876. [ 3.716896@3] sd: clock 50000000, 4-bit-bus-width
  877.  
  878. [ 3.721921@3] mmcblk1: sd:aaaa SL16G 14.8 GiB
  879. [ 3.735134@3] mmcblk1: p1 p2
  880. [ 3.767260@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  881. [ 3.767311@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  882. [ 3.775450@2] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0xc9000000
  883. [ 3.781256@2] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  884. [ 3.787986@2] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  885. [ 3.795327@2] usb usb1: Product: xHCI Host Controller
  886. [ 3.800417@2] usb usb1: Manufacturer: Linux 3.14.29 xhci-hcd
  887. [ 3.805925@2] usb usb1: SerialNumber: xhci-hcd.0.auto
  888. [ 3.811548@2] hub 1-0:1.0: USB hub found
  889. [ 3.814831@2] hub 1-0:1.0: 2 ports detected
  890. [ 3.819096@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  891. [ 3.824592@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  892. [ 3.832420@2] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
  893. [ 3.839218@2] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  894. [ 3.846556@2] usb usb2: Product: xHCI Host Controller
  895. [ 3.851574@2] usb usb2: Manufacturer: Linux 3.14.29 xhci-hcd
  896. [ 3.857157@2] usb usb2: SerialNumber: xhci-hcd.0.auto
  897. [ 3.862672@2] hub 2-0:1.0: USB hub found
  898. [ 3.866060@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
  899. [ 3.873761@1] console [netcon0] enabled
  900. [ 3.877079@1] netconsole: network logging started
  901. [ 3.881797@1] aml_vrtc rtc.31: setting system clock to 2015-01-01 00:00:07 UTC (1420070407)
  902. [ 3.890870@1] cpufreq-scpi cpufreq-meson.7: enter cpufreq
  903. [ 3.895477@1] cpufreq-scpi cpufreq-meson.7: probe cpufreq okay
  904. [ 3.901997@1] gxbb_pm: enter meson_pm_probe!
  905. [ 3.905573@1] gxbb_pm: meson_pm_probe done
  906. [ 3.910331@0] cpucore_cooling_register, max_cpu_core_num:4
  907. [ 3.931824@0] aml_istbt_dev_ready NULL
  908. [ 3.931882@0] ALSA device list:
  909. [ 3.933056@0] #0: AML-M8AUDIO
  910. [ 3.936645@0] Freeing unused kernel memory: 1092K (ffffffc001b38000 - ffffffc001c49000)
  911.  
  912. bl30 get wakeup sources!
  913. process command 00000006
  914. bl30 enter suspend!
  915. cpu clk suspend rate 1416000000
  916. suspend_counter: 1
  917. Enter ddr suspend
  918. first time suspend
  919. ddr suspend time: 1887us
  920. store restore gp0 pll
  921. process command 00000001
  922. CEC cfg:0x0000
  923. set vddee to 0x035cmv
  924. 08915d0000000000
  925.  
  926. exit_reason:0x02
  927. set vddee to 0x03e8mv
  928. set vcck to 0x0460mv
  929. store restore gp0 pll
  930. gp0 pll can't lock
  931. read gp0_ctrl 40000000
  932. read gp0_ctrl2 0
  933. read gp0_ctrl3 0
  934. read gp0_ctrl4 0
  935. Enter ddr resume
  936. ddr resume time: 365us
  937. cfg15 3b00000
  938. cfg15 23b00000
  939. cpu clk resume rate 1000000000
  940.  
  941. bl30 get wakeup sources!
  942. process command 00000006
  943. bl30 enter suspend!
  944. cpu clk suspend rate 1416000000
  945. suspend_counter: 2
  946. Enter ddr suspend
  947. not first time suspend
  948. ddr suspend time: 2239us
  949. store restore gp0 pll
  950. process command 00000001
  951. CEC cfg:0x0000
  952. set vddee to 0x035cmv
  953. 08915d0000000000
  954.  
  955. exit_reason:0x02
  956. set vddee to 0x03e8mv
  957. set vcck to 0x0460mv
  958. store restore gp0 pll
  959. gp0 pll can't lock
  960. read gp0_ctrl 40000000
  961. read gp0_ctrl2 0
  962. read gp0_ctrl3 0
  963. read gp0_ctrl4 0
  964. Enter ddr resume
  965. ddr resume time: 364us
  966. cfg15 23b00000
  967. cfg15 23b00000
  968. cpu clk resume rate 1000000000
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!