Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- NOTICE: BL31: BL33 decompress pass
- ERROR: Error initializing runtime service opteed_fast
- U-Boot 2015.01 (Jan 09 2019 - 09:24:51)
- DRAM: 3.8 GiB
- Relocation Offset is: d6e81000
- spi_post_bind(spifc): req_seq = 0
- register usb cfg[0][1] = 00000000d7f47f60
- NAND: get_sys_clk_rate_mtd() 266, clock setting 200!
- NAND device id: 0 ff ff ff ff ff
- No NAND device found!!!
- nand init failed: -6
- get_sys_clk_rate_mtd() 266, clock setting 200!
- NAND device id: 0 ff ff ff ff ff
- No NAND device found!!!
- nand init failed: -6
- MMC: aml_priv->desc_buf = 0x00000000d3e71710
- aml_priv->desc_buf = 0x00000000d3e73a30
- SDIO Port B: 0, SDIO Port C: 1
- co-phase 0x3, tx-dly 0, clock 400000
- co-phase 0x3, tx-dly 0, clock 400000
- co-phase 0x3, tx-dly 0, clock 400000
- emmc/sd response timeout, cmd8, status=0x1ff2800
- emmc/sd response timeout, cmd55, status=0x1ff2800
- co-phase 0x3, tx-dly 0, clock 400000
- co-phase 0x3, tx-dly 0, clock 40000000
- init_part() 297: PART_TYPE_AML
- [mmc_init] mmc init success
- start dts,buffer=00000000d3e76280,dt_addr=00000000d3e76280
- get_partition_from_dts() 105: ret 0
- parts: 14
- 00: logo 0000000000800000 1
- 01: recovery 0000000001800000 1
- 02: misc 0000000000800000 1
- 03: dto 0000000000800000 1
- 04: cri_data 0000000000800000 2
- 05: param 0000000001000000 2
- 06: boot 0000000001000000 1
- 07: rsv 0000000001000000 1
- 08: tee 0000000002000000 1
- 09: vendor 0000000074000000 1
- 10: odm 0000000010000000 1
- 11: system 0000000074000000 1
- 12: cache 0000000046000000 2
- 13: data ffffffffffffffff 4
- init_part() 297: PART_TYPE_AML
- eMMC/TSD partition table have been checked OK!
- check pattern success
- mmc env offset: 0x4d400000
- In: serial
- Out: serial
- Err: serial
- reboot_mode=cold_boot
- [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
- _verify_dtb_checksum()-2755: calc 2aca6abc, store 2aca6abc
- _verify_dtb_checksum()-2755: calc 2aca6abc, store 2aca6abc
- dtb_read()-2972: total valid 2
- update_old_dtb()-2953: do nothing
- amlkey_init() enter!
- [EFUSE_MSG]keynum is 4
- vpu: clk_level in dts: 7
- vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
- vpu: vpu_clk_gate_init_off finish
- vpp: vpp_init
- vpp: g12a/b osd1 matrix rgb2yuv ..............
- vpp: g12a/b osd2 matrix rgb2yuv..............
- vpp: g12a/b osd3 matrix rgb2yuv..............
- aml_config_dtb 608
- aml_config_dtb 638
- co_phase = <0x00000003>
- caps2 = "MMC_CAP2_HS200"
- f_max = "
- ▒▒"
- status = "disabled"
- status = "okay"
- Net: dwmac.ff3f0000amlkey_init() enter!
- amlkey_init() 71: already init!
- [EFUSE_MSG]keynum is 4
- MACADDR:02:00:00:17:21:01(from chipid)
- Start read misc partition datas!
- info->attemp_times = 0
- info->active_slot = 0
- info->slot_info[0].bootable = 1
- info->slot_info[0].online = 1
- info->slot_info[1].bootable = 0
- info->slot_info[1].online = 0
- info->attemp_times = 0
- attemp_times = 0
- active slot = 0
- wipe_data=successful
- wipe_cache=successful
- upgrade_step=2
- hpd_state=0
- [OSD]load fb addr from dts:/meson-fb
- [OSD]set initrd_high: 0x7f800000
- [OSD]fb_addr for logo: 0x7f800000
- [OSD]load fb addr from dts:/meson-fb
- [OSD]fb_addr for logo: 0x7f800000
- [OSD]VPP_OFIFO_SIZE:0xfff01fff
- [CANVAS]canvas init
- [CANVAS]addr=0x7f800000 width=3840, height=2160
- [OSD]osd_hw.free_dst_data: 0,719,0,575
- [OSD]osd1_update_disp_freescale_enable
- vpp: vpp_matrix_update: 2
- cvbs performance type = 9, table = 0
- cvbs_config_hdmipll_g12a
- cvbs_set_vid2_clk
- amlkey_init() enter!
- amlkey_init() 71: already init!
- [EFUSE_MSG]keynum is 4
- [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
- [KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
- [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
- Unknown command 'upgrade_sadckey' - try 'help'
- gpio: pin GPIOAO_3 (gpio 3) value is 1
- Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
- g12a_u211_v1#: Training has run
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement