Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- smartctl 6.3 2014-05-01 r3901 [ppc-linux-2.6.32.61-taskstat] (local build)
- Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Model Family: Western Digital Red (AF)
- Device Model: WDC WD30EFRX-68AX9N0
- Serial Number: WD-WMC1T05XXXX
- LU WWN Device Id: 5 0014ee 0036e9d33
- Firmware Version: 80.00A80
- User Capacity: 3а000а592а982а016 bytes [3,00 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Device is: In smartctl database [for details use: -P show]
- ATA Version is: ACS-2 (minor revision not indicated)
- SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
- Local Time is: Fri May 16 16:56:48 2014 MSK
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- AAM feature is: Unavailable
- APM feature is: Unavailable
- Rd look-ahead is: Enabled
- Write cache is: Enabled
- ATA Security is: Disabled, NOT FROZEN [SEC1]
- Wt Cache Reorder: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: (40500) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 2) minutes.
- Extended self-test routine
- recommended polling time: ( 406) minutes.
- Conveyance self-test routine
- recommended polling time: ( 5) minutes.
- SCT capabilities: (0x70bd) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 16
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
- 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
- 3 Spin_Up_Time POS--K 185 180 021 - 5741
- 4 Start_Stop_Count -O--CK 100 100 000 - 908
- 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
- 7 Seek_Error_Rate -OSR-K 200 200 000 - 0
- 9 Power_On_Hours -O--CK 083 083 000 - 12414
- 10 Spin_Retry_Count -O--CK 100 100 000 - 0
- 11 Calibration_Retry_Count -O--CK 100 253 000 - 0
- 12 Power_Cycle_Count -O--CK 100 100 000 - 29
- 192 Power-Off_Retract_Count -O--CK 200 200 000 - 14
- 193 Load_Cycle_Count -O--CK 200 200 000 - 893
- 194 Temperature_Celsius -O---K 103 090 000 - 47
- 196 Reallocated_Event_Count -O--CK 200 200 000 - 0
- 197 Current_Pending_Sector -O--CK 200 200 000 - 0
- 198 Offline_Uncorrectable ----CK 100 253 000 - 0
- 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 39
- 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
- ||||||_ K auto-keep
- |||||__ C event count
- ||||___ R error rate
- |||____ S speed/performance
- ||_____ O updated online
- |______ P prefailure warning
- General Purpose Log Directory Version 1
- SMART Log Directory Version 1 [multi-sector log support]
- Address Access R/W Size Description
- 0x00 GPL,SL R/O 1 Log Directory
- 0x01 SL R/O 1 Summary SMART error log
- 0x02 SL R/O 5 Comprehensive SMART error log
- 0x03 GPL R/O 6 Ext. Comprehensive SMART error log
- 0x06 SL R/O 1 SMART self-test log
- 0x07 GPL R/O 1 Extended self-test log
- 0x09 SL R/W 1 Selective self-test log
- 0x10 GPL R/O 1 NCQ Command Error log
- 0x11 GPL R/O 1 SATA Phy Event Counters
- 0x21 GPL R/O 1 Write stream error log
- 0x22 GPL R/O 1 Read stream error log
- 0x80-0x9f GPL,SL R/W 16 Host vendor specific log
- 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
- 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
- 0xbd GPL,SL VS 1 Device vendor specific log
- 0xc0 GPL,SL VS 1 Device vendor specific log
- 0xc1 GPL VS 93 Device vendor specific log
- 0xe0 GPL,SL R/W 1 SCT Command/Status
- 0xe1 GPL,SL R/W 1 SCT Data Transfer
- SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
- Device Error Count: 1
- CR = Command Register
- FEATR = Features Register
- COUNT = Count (was: Sector Count) Register
- LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
- LH = LBA High (was: Cylinder High) Register ] LBA
- LM = LBA Mid (was: Cylinder Low) Register ] Register
- LL = LBA Low (was: Sector Number) Register ]
- DV = Device (was: Device/Head) Register
- DC = Device Control Register
- ER = Error register
- ST = Status register
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 1 [0] occurred at disk power-on lifetime: 7758 hours (323 days + 6 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER -- ST COUNT LBA_48 LH LM LL DV DC
- -- -- -- == -- == == == -- -- -- -- --
- 40 -- 51 00 08 00 00 00 49 b9 f0 e0 00 Error: UNC 8 sectors at LBA = 0x0049b9f0 = 4831728
- Commands leading to the command that caused the error were:
- CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
- -- == -- == -- == == == -- -- -- -- -- --------------- --------------------
- c8 00 00 00 08 00 00 00 49 b9 f0 e0 08 00:00:24.798 READ DMA
- c8 00 00 00 08 00 00 00 49 b9 d0 e0 08 00:00:24.798 READ DMA
- c8 00 00 00 08 00 00 00 49 b9 c8 e0 08 00:00:24.798 READ DMA
- c8 00 00 00 08 00 00 00 49 b9 c0 e0 08 00:00:24.798 READ DMA
- c8 00 00 00 08 00 00 00 49 b9 b8 e0 08 00:00:24.798 READ DMA
- SMART Extended Self-test Log Version: 1 (1 sectors)
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Extended offline Completed without error 00% 2320 -
- # 2 Extended offline Completed without error 00% 526 -
- # 3 Short offline Completed without error 00% 36873 -
- # 4 Short offline Completed without error 00% 1 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
- SCT Status Version: 3
- SCT Version (vendor specific): 258 (0x0102)
- SCT Support Level: 1
- Device State: Active (0)
- Current Temperature: 47 Celsius
- Power Cycle Min/Max Temperature: 29/51 Celsius
- Lifetime Min/Max Temperature: 18/60 Celsius
- Under/Over Temperature Limit Count: 0/0
- SCT Temperature History Version: 2
- Temperature Sampling Period: 1 minute
- Temperature Logging Interval: 1 minute
- Min/Max recommended Temperature: 0/60 Celsius
- Min/Max Temperature Limit: -41/85 Celsius
- Temperature History Size (Index): 478 (374)
- Index Estimated Time Temperature Celsius
- 375 2014-05-16 08:59 47 ****************************
- ... ..( 2 skipped). .. ****************************
- 378 2014-05-16 09:02 47 ****************************
- 379 2014-05-16 09:03 48 *****************************
- ... ..( 43 skipped). .. *****************************
- 423 2014-05-16 09:47 48 *****************************
- 424 2014-05-16 09:48 47 ****************************
- ... ..(364 skipped). .. ****************************
- 311 2014-05-16 15:53 47 ****************************
- 312 2014-05-16 15:54 48 *****************************
- ... ..( 48 skipped). .. *****************************
- 361 2014-05-16 16:43 48 *****************************
- 362 2014-05-16 16:44 47 ****************************
- ... ..( 11 skipped). .. ****************************
- 374 2014-05-16 16:56 47 ****************************
- SCT Error Recovery Control:
- Read: 70 (7,0 seconds)
- Write: 70 (7,0 seconds)
- Device Statistics (GP Log 0x04) not supported
- SATA Phy Event Counters (GP Log 0x11)
- ID Size Value Description
- 0x0001 2 0 Command failed due to ICRC error
- 0x0002 2 0 R_ERR response for data FIS
- 0x0003 2 0 R_ERR response for device-to-host data FIS
- 0x0004 2 0 R_ERR response for host-to-device data FIS
- 0x0005 2 0 R_ERR response for non-data FIS
- 0x0006 2 0 R_ERR response for device-to-host non-data FIS
- 0x0007 2 0 R_ERR response for host-to-device non-data FIS
- 0x0008 2 0 Device-to-host non-data FIS retries
- 0x0009 2 11 Transition from drive PhyRdy to drive PhyNRdy
- 0x000a 2 12 Device-to-host register FISes sent due to a COMRESET
- 0x000b 2 0 CRC errors within host-to-device FIS
- 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
- 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
- 0x8000 4 13020448 Vendor specific
- ryzhovau@MBL160:~/projects/smartmontools$
Add Comment
Please, Sign In to add comment