[    2.371823] libphy: qca8k slave mii: probed
[    2.664211] qca8k 37000000.mdio-mii:10: configuring for fixed/rgmii-id link mode
[    2.679517] qca8k 37000000.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[    2.802172] qca8k 37000000.mdio-mii:10 lan1 (uninitialized): PHY [qca8k-0:00] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    2.932161] qca8k 37000000.mdio-mii:10 lan2 (uninitialized): PHY [qca8k-0:01] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    3.062151] qca8k 37000000.mdio-mii:10 lan3 (uninitialized): PHY [qca8k-0:02] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    3.191954] qca8k 37000000.mdio-mii:10 lan4 (uninitialized): PHY [qca8k-0:03] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    3.322161] qca8k 37000000.mdio-mii:10 wan (uninitialized): PHY [qca8k-0:04] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[    3.331679] CONNECTED
[    3.331694] CALLED CONNECT PROTO
[    3.332962] device eth0 entered promiscuous mode
[    3.338600] DSA: tree 0 setup
[    3.350515] thermal thermal_zone0: failed to read out thermal zone (-110)
[    3.362665] UBI: auto-attach mtd6
[    3.362713] ubi0: attaching mtd6
[    3.467809] random: crng init done
[    4.176904] ubi0: scanning is finished
[    4.187287] ubi0: attached mtd6 (name "ubi", size 96 MiB)
[    4.187315] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.191752] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.198434] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.205358] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0
[    4.212137] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    4.218313] ubi0: max/mean erase counter: 50/33, WL threshold: 4096, image sequence number: 1615651602
[    4.225416] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20
[    4.250680] ubi0: background thread "ubi_bgt0d" started, PID 85
[    4.251163] block ubiblock0_0: created from ubi0:0(rootf�[    4.265074] Freeing unused kernel image (initmem) memory: 5120K
[    4.265454] Run /init as init process
[    4.522192] init: Console is alive
[    4.522488] init: - watchdog -
[    4.551640] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.556043] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.560467] SCSI subsystem initialized
[    4.565490] ehci-fsl: Freescale EHCI Host controller driver
[    4.568128] ehci-platform: EHCI generic platform driver
[    4.576805] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found
[    4.578266] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found
[    4.584300] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found
[    4.590245] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found
[    4.597948] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found
[    4.601971] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found
[    4.607604] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found
[    4.613729] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found
[    4.693721] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.693780] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    4.698288] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010
[    4.705794] xhci-hcd xhci-hcd.0.auto: irq 49, io mem 0x11000000
[    4.716025] hub 1-0:1.0: USB hub found
[    4.721085] hub 1-0:1.0: 1 port detected
[    4.725090] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    4.728845] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    4.734233] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    4.742927] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.748740] hub 2-0:1.0: USB hub found
[    4.756702] hub 2-0:1.0: 1 port detected
[    4.764389] usbcore: registered new interface driver usb-storage
[    4.764669] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.771356] init: - preinit -
[    5.037529] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[    5.038594] dwmac1000: Master AXI performs any burst length
[    5.044823] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[    5.049997] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    5.058242] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[    5.067861] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[    5.074514] call master up
[    5.074673] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[    6.099938] FUNCTION TIMEOUT!!!
[    7.140153] FUNCTION TIMEOUT!!!
[    7.144536] qca8k 37000000.mdio-mii:10 lan1: configuring for phy/internal link mode
[    7.146901] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   10.329747] procd: - early -
[   10.329942] procd: - watchdog -
[   10.877457] procd: - watchdog -
[   10.878320] procd: - ubus -
[   10.937098] procd: - init -
Please press Enter to activate this console.
[   11.120008] urngd: v1.0.2 started.
[   11.141344] kmodloader: loading kernel modules from /etc/modules.d/*
[   11.156609] usbcore: registered new interface driver ums-alauda
[   11.157222] usbcore: registered new interface driver ums-cypress
[   11.162003] usbcore: registered new interface driver ums-datafab
[   11.168196] usbcore: registered new interface driver ums-freecom
[   11.174269] usbcore: registered new interface driver ums-isd200
[   11.180195] usbcore: registered new interface driver ums-jumpshot
[   11.186418] usbcore: registered new interface driver ums-karma
[   11.192245] usbcore: registered new interface driver ums-sddr09
[   11.197814] usbcore: registered new interface driver ums-sddr55
[   11.203789] usbcore: registered new interface driver ums-usbat
[   11.212044] xt_time: kernel timezone is -0000
[   11.236617] kmodloader: done loading kernel modules from /etc/modules.d/*
[   15.968410] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Down
[   15.972389] ipq806x-gmac-dwmac 37200000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   15.974063] dwmac1000: Master AXI performs any burst length
[   15.981901] ipq806x-gmac-dwmac 37200000.ethernet eth0: No Safety Features support found
[   15.987121] ipq806x-gmac-dwmac 37200000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   15.995276] ipq806x-gmac-dwmac 37200000.ethernet eth0: registered PTP clock
[   16.004220] ipq806x-gmac-dwmac 37200000.ethernet eth0: configuring for fixed/rgmii link mode
[   16.011140] call master up
[   16.011615] ipq806x-gmac-dwmac 37200000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   16.025751] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   16.052422] qca8k 37000000.mdio-mii:10 lan1: configuring for phy/internal link mode
[   16.170798] br-lan: port 1(lan1) entered blocking state
[   16.170828] br-lan: port 1(lan1) entered disabled state
[   16.178417] device lan1 entered promiscuous mode
[   16.203056] qca8k 37000000.mdio-mii:10 lan2: configuring for phy/internal link mode
[   16.203310] br-lan: port 2(lan2) entered blocking state
[   16.209600] br-lan: port 2(lan2) entered disabled state
[   16.220501] device lan2 entered promiscuous mode
[   16.231778] qca8k 37000000.mdio-mii:10 lan3: configuring for phy/internal link mode
[   16.232045] br-lan: port 3(lan3) entered blocking state
[   16.238349] br-lan: port 3(lan3) entered disabled state
[   16.248552] device lan3 entered promiscuous mode
[   16.260946] qca8k 37000000.mdio-mii:10 lan4: configuring for phy/internal link mode
[   16.261252] br-lan: port 4(lan4) entered blocking state
[   16.267485] br-lan: port 4(lan4) entered disabled state
[   16.277933] device lan4 entered promiscuous mode
[   16.288998] qca8k 37000000.mdio-mii:10 wan: configuring for phy/internal link mode
[   16.293314] qca8k 37000000.mdio-mii:10 lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[   16.295610] br-lan: port 3(lan3) entered blocking state
[   16.303805] br-lan: port 3(lan3) entered forwarding state
[   16.316123] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready