API tools faq
paste
Advertisement
LaserOval

coco-bot config 1/17/21

LaserOval
Jan 17th, 2021
131
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 31.10 KB | None | 0 0
raw download clone embed print report
  1. config.txt
  2.  
  3. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  4. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  5. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  6.  
  7. # Basic motion configuration
  8. default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves
  9. default_seek_rate 4000 # Default speed (mm/minute) for G0 moves
  10. mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable
  11. mm_per_line_segment 5 # Cut lines into segments this size
  12. mm_max_arc_error 0.0 # The maximum error for line segments that divide arcs 0 to disable
  13. # note it is invalid for both the above be 0
  14. # if both are used, will use largest segment length based on radius
  15. grbl_mode true # using bCNC as firmware=
  16.  
  17. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  18. # See http://smoothieware.org/stepper-motors
  19. alpha_steps_per_mm 12 # Steps per mm for alpha ( X ) stepper
  20. beta_steps_per_mm 12 # Steps per mm for beta ( Y ) stepper
  21. gamma_steps_per_mm 1600 # Steps per mm for gamma ( Z ) stepper, gamma is the laser, not a stepper, should this be ignored?
  22.  
  23. # Planner module configuration : Look-ahead and acceleration configuration
  24. # See http://smoothieware.org/motion-control
  25. acceleration 3000 # Acceleration in mm/second/second.
  26. #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  27. junction_deviation 0.05 # See http://smoothieware.org/motion-control#junction-deviation
  28. #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  29.  
  30. # Cartesian axis speed limits
  31. x_axis_max_speed 3000 # Maximum speed in mm/min
  32. y_axis_max_speed 3000 # Maximum speed in mm/min
  33. z_axis_max_speed 300 # Maximum speed in mm/min, gamma is the laser, not a stepper, should this be ignored?
  34.  
  35. # Stepper module configuration
  36. # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
  37. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  38. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  39. alpha_dir_pin 0.5 # Pin for alpha stepper direction, add '!' to reverse direction
  40. alpha_en_pin 0.4 # Pin for alpha enable pin
  41. alpha_current 0.9 # X stepper motor current
  42. alpha_max_rate 30000.0 # Maximum rate in mm/min
  43.  
  44. beta_step_pin 2.1 # Pin for beta stepper step signal
  45. beta_dir_pin 0.11 # Pin for beta stepper direction, add '!' to reverse direction
  46. beta_en_pin 0.10 # Pin for beta enable
  47. beta_current 0.9 # Y stepper motor current
  48. beta_max_rate 30000.0 # Maxmimum rate in mm/min
  49.  
  50. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  51. gamma_dir_pin 0.20 # Pin for gamma stepper direction, add '!' to reverse direction
  52. gamma_en_pin 0.19 # Pin for gamma enable
  53. gamma_current 0 # Z stepper motor current
  54. gamma_max_rate 300.0 # Maximum rate in mm/min
  55.  
  56. ## Extruder module configuration
  57. # See http://smoothieware.org/extruder
  58. extruder.hotend.enable false # Whether to activate the extruder module at all. All configuration is ignored if false
  59. extruder.hotend.steps_per_mm 140 # Steps per mm for extruder stepper
  60. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  61. extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
  62. extruder.hotend.max_speed 50 # Maximum speed in mm/s
  63.  
  64. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  65. extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal ( add '!' to reverse direction )
  66. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  67.  
  68. # Extruder offset
  69. #extruder.hotend.x_offset 0 # X offset from origin in mm
  70. #extruder.hotend.y_offset 0 # Y offset from origin in mm
  71. #extruder.hotend.z_offset 0 # Z offset from origin in mm
  72.  
  73. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  74. #extruder.hotend.retract_length 3 # Retract length in mm
  75. #extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec
  76. #extruder.hotend.retract_recover_length 0 # Additional length for recover
  77. #extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
  78. #extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
  79. #extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  80.  
  81. #delta_current 1.5 # First extruder stepper motor current
  82.  
  83. # Second extruder module configuration
  84. #extruder.hotend2.enable False # Whether to activate the extruder module at all. All configuration is ignored if false
  85. #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
  86. #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  87. #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  88. #extruder.hotend2.max_speed 50 # mm/s
  89.  
  90. #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  91. #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
  92. #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  93.  
  94. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  95. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  96. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  97.  
  98. #epsilon_current 1.5 # Second extruder stepper motor current
  99.  
  100.  
  101. ## Laser module configuration
  102. # See http://smoothieware.org/laser
  103. laser_module_enable True # Whether to activate the laser module at all
  104. laser_module_pwm_pin 2.5 # This pin will be PWMed to control the laser.
  105. # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
  106. laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off.
  107. laser_module_maximum_power 1.0 # This is the maximum duty cycle that will be applied to the laser
  108. laser_module_minimum_power 0.1 # This is a value just below the minimum duty cycle that keeps the laser
  109. # active without actually burning.
  110. laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
  111. # the maximum and minimum power levels specified above
  112. laser_module_pwm_period 200 # This sets the pwm frequency as the period in microseconds. LW4 asked this to be 200
  113.  
  114. ## Temperature control configuration
  115. # See http://smoothieware.org/temperaturecontrol
  116.  
  117. # First hotend configuration
  118. temperature_control.hotend.enable false # Whether to activate this ( "hotend" ) module at all.
  119. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  120. temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  121. temperature_control.hotend.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#toc5
  122. #temperature_control.hotend.beta 4066 # Or set the beta value
  123. temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
  124. temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  125. temperature_control.hotend.designator T # Designator letter for this module
  126. #temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
  127. #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  128.  
  129. # Safety control is enabled by default and can be overidden here, the values show the defaults
  130. # See http://smoothieware.org/temperaturecontrol#runaway
  131. #temperature_control.hotend.runaway_heating_timeout 900 # How long it can take to heat up, max is 2040 seconds.
  132. #temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  133. #temperature_control.hotend.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C
  134.  
  135. # PID configuration
  136. # See http://smoothieware.org/temperaturecontrol#pid
  137. #temperature_control.hotend.p_factor 13.7 # P ( proportional ) factor
  138. #temperature_control.hotend.i_factor 0.097 # I ( integral ) factor
  139. #temperature_control.hotend.d_factor 24 # D ( derivative ) factor
  140.  
  141. #temperature_control.hotend.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  142.  
  143. # Second hotend configuration
  144. #temperature_control.hotend2.enable false # Whether to activate this ( "hotend" ) module at all.
  145. #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
  146. #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
  147. #temperature_control.hotend2.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor
  148. ##temperature_control.hotend2.beta 4066 # or set the beta value
  149. #temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
  150. #temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  151. #temperature_control.hotend2.designator T1 # Designator letter for this module
  152.  
  153. #temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor
  154. #temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor
  155. #temperature_control.hotend2.d_factor 24 # D ( derivative ) factor
  156.  
  157. #temperature_control.hotend2.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  158.  
  159. temperature_control.bed.enable false # Whether to activate this ( "hotend" ) module at all.
  160. temperature_control.bed.thermistor_pin 0.24 # Pin for the thermistor to read
  161. temperature_control.bed.heater_pin 2.5 # Pin that controls the heater
  162. temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  163. #temperature_control.bed.beta 3974 # Or set the beta value
  164. temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
  165. temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
  166. temperature_control.bed.designator B # Designator letter for this module
  167.  
  168. # Bang-bang ( simplified ) control
  169. # See http://smoothieware.org/temperaturecontrol#bang-bang
  170. #temperature_control.bed.bang_bang false # Set to true to use bang bang control rather than PID
  171. #temperature_control.bed.hysteresis 2.0 # Set to the temperature in degrees C to use as hysteresis
  172.  
  173. ## Switch modules
  174. # See http://smoothieware.org/switch
  175.  
  176. # Switch module for fan control
  177. switch.fan_one.enable true # Enable this module. Intake fan, left BOTTOM
  178. switch.fan_one.input_on_command M106 # Command that will turn this switch on
  179. switch.fan_one.input_off_command M107 # Command that will turn this switch off
  180. switch.fan_one.output_pin 2.6 # Pin this module controls
  181. switch.fan_one.output_type pwm # PWM output settable with S parameter in the input_on_comand
  182. switch.fan_one.max_pwm 255 # Set max pwm for the pin default is 255
  183. switch.fan_one.startup_state true #start up state of the switch, you want always on
  184.  
  185. switch.fan_two.enable true # Enable this module. Exhaust Fan, TOP right side
  186. switch.fan_two.input_on_command M106 # Command that will turn this switch on
  187. switch.fan_two.input_off_command M107 # Command that will turn this switch off
  188. switch.fan_two.output_pin 2.4 # Pin this module controls
  189. switch.fan_two.output_type pwm # PWM output settable with S parameter in the input_on_comand
  190. switch.fan_two.max_pwm 255 # Set max pwm for the pin default is 255
  191. switch.fan_two.startup_state true #start up state of the switch, you want always on
  192.  
  193. switch.fan_three.enable true # Enable this module, Exhaust fan BOTTOM right
  194. switch.fan_three.input_on_command M106 # Command that will turn this switch on
  195. switch.fan_three.input_off_command M107 # Command that will turn this switch off
  196. switch.fan_three.output_pin 2.7 # Pin this module controls
  197. switch.fan_three.output_type pwm # PWM output settable with S parameter in the input_on_comand
  198. switch.fan_three.max_pwm 255 # Set max pwm for the pin default is 255
  199. switch.fan_three.startup_state true #start up state of the switch, you want always on
  200.  
  201. switch.fan_four.enable true # Enable this module Intake fan left TOP
  202. switch.fan_four.input_on_command M106 # Command that will turn this switch on
  203. switch.fan_four.input_off_command M107 # Command that will turn this switch off
  204. switch.fan_four.output_pin 2.5 # Pin this module controls
  205. switch.fan_four.output_type pwm # PWM output settable with S parameter in the input_on_comand
  206. switch.fan_four.max_pwm 255 # Set max pwm for the pin default is 255
  207. switch.fan_four.startup_state true #start up state of the switch, you want always on
  208.  
  209.  
  210. #switch.misc.enable true # Enable this module
  211. #switch.misc.input_on_command M42 # Command that will turn this switch on
  212. #switch.misc.input_off_command M43 # Command that will turn this switch off
  213. #switch.misc.output_pin 2.4 # Pin this module controls
  214. #switch.misc.output_type digital # Digital means this is just an on or off pin
  215.  
  216. #switch.bltouch.enable true #
  217. #switch.bltouch.output_pin 2.4 # sw pwm can use any digital pin
  218. #switch.bltouch.input_on_command M280 #
  219. #switch.bltouch.input_off_command M281 #
  220. #switch.bltouch.output_type swpwm # sw pwm must be low frequency
  221. #switch.bltouch.pwm_period_ms 20 # 50Hz
  222. #switch.bltouch.startup_state false # start up in the stow state
  223. #switch.bltouch.startup_value 7.43 # On boot it will go into stow mode, also set with the M281
  224. #switch.bltouch.default_on_value 3.3 # if M280 is issued without S this is the value it will set it to
  225.  
  226.  
  227. ## Temperatureswitch
  228. # See http://smoothieware.org/temperatureswitch
  229. # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  230. # Useful to turn on a fan or water pump to cool the hotend
  231. #temperatureswitch.hotend.enable true #
  232. #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  233. #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
  234. #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
  235. #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
  236. #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
  237.  
  238. ## Endstops
  239. # See http://smoothieware.org/endstops
  240. endstops_enable false # The endstop module is enabled by default and can be disabled here
  241. #corexy_homing false # Set to true if homing on a hbot or corexy
  242. alpha_min_endstop 1.24^! # X Axis-Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  243. #alpha_max_endstop 1.25^! # X Axis-Pin to read max endstop, uncomment this and comment the above if using max endstops
  244. #alpha_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  245. #alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
  246. #alpha_max 200 # This gets loaded as the current position after homing when home_to_max is set
  247. beta_min_endstop 1.26^ # Y Axis-Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  248. beta_max_endstop 1.27^ # Y Axis-Pin to read max endstop, uncomment this and comment the above if using max endstops
  249. #beta_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  250. #beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
  251. #beta_max 200 # This gets loaded as the current position after homing when home_to_max is set
  252. gamma_min_endstop 1.28^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  253. gamma_max_endstop 1.29^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  254. #gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  255. #gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
  256. #gamma_max 200 # This gets loaded as the current position after homing when home_to_max is set
  257.  
  258. #alpha_max_travel 200 # X Axis Max travel in mm for alpha/X axis when homing
  259. #beta_max_travel 400 # Y Axis-Max travel in mm for beta/Y axis when homing
  260. #gamma_max_travel 500 # Max travel in mm for gamma/Z axis when homing
  261.  
  262. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
  263. alpha_limit_enable false # Set to true to enable X min and max limit switches
  264. beta_limit_enable False # Set to true to enable Y min and max limit switches
  265. gamma_limit_enable False # Set to true to enable Z min and max limit switches
  266.  
  267. # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
  268. alpha_fast_homing_rate_mm_s 50 # Alpha/X fast homing feedrate in mm/second
  269. alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
  270. beta_fast_homing_rate_mm_s 50 # Beta/Y fast homing feedrate in mm/second
  271. beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
  272. gamma_fast_homing_rate_mm_s 4 # Gamma/Z fast homing feedrate in mm/second
  273. gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
  274.  
  275. alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
  276. beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
  277. gamma_homing_retract_mm 1 # Distance to retract from the endstop after it is hit for gamma/Z
  278.  
  279.  
  280. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
  281. #alpha_limit_enable true # Set to true to enable X min and max limit switches
  282. #beta_limit_enable true # Set to true to enable Y min and max limit switches
  283. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  284.  
  285. # Optional order in which axis will home, default is they all home at the same time,
  286. # If this is set it will force each axis to home one at a time in the specified order
  287. #homing_order YX # X axis followed by Y then Z last
  288. #move_to_origin_after_home false # Move XY to 0,0 after homing
  289. #endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
  290. #endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
  291. #home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
  292.  
  293. # End of endstop config
  294. # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
  295. #include abc-endstop.config
  296.  
  297. ## Z-probe
  298. # See http://smoothieware.org/zprobe
  299. zprobe.enable false # Set to true to enable a zprobe
  300. #zprobe.probe_pin 1.28!^ # Pin probe is attached to, if NC remove the !
  301. zprobe.slow_feedrate 5 # Mm/sec probe feed rate
  302. #zprobe.debounce_ms 1 # Set if noisy
  303. zprobe.fast_feedrate 100 # Move feedrate mm/sec
  304. zprobe.probe_height 5 # How much above bed to start probe
  305. #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
  306.  
  307. # Levelling strategy
  308. # Example for 3-point levelling strategy, see wiki documentation for other strategies
  309. #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  310. #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
  311. #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
  312. #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
  313. #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
  314. #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  315. #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
  316. #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
  317.  
  318. ## Panel
  319. # See http://smoothieware.org/panel
  320. # Please find your panel on the wiki and copy/paste the right configuration here
  321. panel.enable false # Set to true to enable the panel code
  322.  
  323. # Example for reprap discount GLCD
  324. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  325. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  326. #panel.lcd reprap_discount_glcd #
  327. #panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  328. #panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4
  329. #panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3
  330. #panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5
  331. #panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2
  332. #panel.buzz_pin 1.31 # Pin for buzzer ; GLCD EXP1 Pin 1
  333. #panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8
  334.  
  335. panel.menu_offset 0 # Some panels will need 1 here
  336.  
  337. panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
  338. panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
  339. panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
  340.  
  341. panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
  342. panel.bed_temperature 60 # Temp to set bed when preheat is selected
  343.  
  344. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  345. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  346. custom_menu.power_on.enable true #
  347. custom_menu.power_on.name Power_on #
  348. custom_menu.power_on.command M80 #
  349.  
  350. custom_menu.power_off.enable true #
  351. custom_menu.power_off.name Power_off #
  352. custom_menu.power_off.command M81 #
  353.  
  354.  
  355. ## Network settings
  356. # See http://smoothieware.org/network
  357. network.enable false # Enable the ethernet network services
  358. network.webserver.enable true # Enable the webserver
  359. network.telnet.enable true # Enable the telnet server
  360. network.ip_address auto # Use dhcp to get ip address
  361. # Uncomment the 3 below to manually setup ip address
  362. #network.ip_address 192.168.3.222 # The IP address
  363. #network.ip_mask 255.255.255.0 # The ip mask
  364. #network.ip_gateway 192.168.3.1 # The gateway address
  365. #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
  366.  
  367. ## System configuration
  368. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  369. # For communication over the UART port, *not* the USB/Serial port
  370. uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
  371.  
  372. second_usb_serial_enable false # This enables a second USB serial port
  373. #leds_disable true # Disable using leds after config loaded
  374. #play_led_disable true # Disable the play led
  375.  
  376. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  377. # See http://smoothieware.org/killbutton
  378. kill_button_enable true # Set to true to enable a kill button
  379. kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  380.  
  381. #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  382. #dfu_enable false # For linux developers, set to true to enable DFU
  383.  
  384. # Only needed on a smoothieboard
  385. # See http://smoothieware.org/currentcontrol
  386. currentcontrol_module_enable true # Control stepper motor current via the configuration file
  387.  
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!