MSP430-NRF905-Notes

SPI Conf:
	W_CONFIG:		0000 xxxx [start addr]
	R_CONFIG:		0001 xxxx [start addr]

	W_TX_PAYLOAD:	0010 0000 [1-32 bytes]
	R_TX_PAYLPAD:	0010 0001 [1-32 bytes]

	W_TX_ADDR:		0010 0010 [1-4 bytes]
	R_TX_ADDR:		0010 0011 [1-4 bytes]

	R_RX_PAYLOAD:	0010 0100 [1-32 bytes]

	CHAN_CONFIG:	1000 pphc [special command for fast setting of CH_NO, HIFREQ_PLL
					cccc cccc  and PA_PWR in the CONF REGISTER.
							   CH_NO = cccccccc, HFREQ_PLL =h, PA_PWR = pp.

Pins:
	TxEN:	Din:	TX/RX mode; 1 = transmit mode.
	VCC:	PWR:	Power supply for moule.
	CE:		Din:	TX/RX enable; 1 = enable, 0 = config mode.
	PWR:	Din:	Power up chip.
	uCK:	Cout:	Output clock?
	CD:		Dout:	Carrier Detect.
	AM:		Dout:	Address Match.
	DR:		Dout:	RX/TX data ready.
	MISO:	SPI:	SPI Output
	MOSI:	SPI:	SPI In
	SCK:	SPI:	SPI Clock
	CSN:	SPI:	SPI enable; 0 = enable
	GND:	PWR:	Ground for module.
Modes:
	Mode:					PWR:	CE:		TxEN:
	Power down and SPI:		0		x		x
	Standby and SPI:		1		0		x
	Read RX register:		1		x		0
	ShockBurst - RX:		1		1		0
	ShockBurst - TX:		1		1		1
MSP430:
	REV2:
		pin01:	VCC				|	pin11:	GND
		pin02:	p1.0	LED1	|	pin12:	XIN
		pin03:	p1.1:	MISO	|	pin13:	XOUT
		pin04:	p1.2:	MOSI	|	pin14:	TEST
		pin05:	p1.3[O]	CSN/SW2	|	pin15:	RST
		pin06:	p1.4:	SCK		|	pin16:	p1.7[O]	TX_EN
		pin07:	p1.5			|	pin17:	p1.6[O]	PWR/LED2
		pin08:	p2.0			|	pin18:	p2.5[O]	CE
		pin09:	p2.1[I]	uCK		|	pin19:	p2.4[I]	AM
		pin10:	p2.2[I]	CD		|	pin20:	p2.3[I]	DR
	REV1:
		pin01:	VCC				|	pin11:	GND
		pin02:	p1.0			|	pin12:	XIN
		pin03:	p1.1:	MISO	|	pin13:	XOUT
		pin04:	p1.2:	MOSI	|	pin14:	TEST
		pin05:	p1.3:	CSN		|	pin15:	RST
		pin06:	p1.4:	SCK		|	pin16:	p1.7:	???
		pin07:	p1.5:	???		|	pin17:	p1.6:	???
		pin08:	p2.0			|	pin18:	p2.5:	???
		pin09:	p2.1			|	pin19:	p2.4	???
		pin10:	p2.2			|	pin20:	p2.3	???