Recv: Axis X home_offset = 0.00 position_shift = 0.00
Recv: > home_offset[X] = 0.00
Recv:   current_position= X0.00 Y0.00 Z16.70 :
Recv: <<< set_axis_is_at_home(X)
Recv:   current_position= X0.00 Y0.00 Z16.70 : sync_plan_position
Recv:   current_position= X0.00 Y0.00 Z16.70 : > AFTER set_axis_is_at_home
Recv: <<< homeaxis(X)
Recv: >>> homeaxis(Y)
Recv: Home 1 Fast:
Recv: >>> do_homing_move  X0.00 Y0.00 Z16.70
Recv: ...(Y, -352.50, [50.00])
Recv: <<< do_homing_move  X0.00 Y0.00 Z16.70
Recv: Move Away:
Recv: >>> do_homing_move  X0.00 Y0.00 Z16.70
Recv: ...(Y, 5.00, [50.00])
Recv: echo:busy: processing
Recv: <<< do_homing_move  X0.00 Y0.00 Z16.70
Recv: Home 2 Slow:
Recv: >>> do_homing_move  X0.00 Y0.00 Z16.70
Recv: ...(Y, -10.00, 25.00)
Recv: <<< do_homing_move  X0.00 Y0.00 Z16.70
Recv: >>> set_axis_is_at_home(Y)
Recv: Axis Y home_offset = 0.00 position_shift = 0.00
Recv: > home_offset[Y] = 0.00
Recv:   current_position= X0.00 Y0.00 Z16.70 :
Recv: <<< set_axis_is_at_home(Y)
Recv:   current_position= X0.00 Y0.00 Z16.70 : sync_plan_position
Recv:   current_position= X0.00 Y0.00 Z16.70 : > AFTER set_axis_is_at_home
Recv: <<< homeaxis(Y)
Recv: BLTouch Command :160
Recv: BLTouch Command :90
Recv: last_written_mode - 1
Recv: config mode - BLTOUCH_SET_5V_MODE
Recv: >>> home_z_safely  X0.00 Y0.00 Z16.70
Recv:   current_position= X0.00 Y0.00 Z16.70 : sync_plan_position
Recv:   destination= X164.20 Y123.00 Z18.40 : home_z_safely
Recv: >>> do_blocking_move_to  X0.00 Y0.00 Z16.70
Recv: >  X164.20 Y123.00 Z16.70
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: >>> homeaxis(Z)
Recv:   current_position= X164.20 Y123.00 Z16.70 : Probe::set_deployed
Recv: deploy: 1
Recv: Probe::do_z_raise(10.00)
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: >  X164.20 Y123.00 Z16.70
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: BLTouch DEPLOY requested
Recv: BLTouch Command :10
Recv: bltouch.deploy_proc() end
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: >  X164.20 Y123.00 Z16.70
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: Home 1 Fast:
Recv: BLTouch DEPLOY requested
Recv: BLTouch Command :10
Recv: bltouch.deploy_proc() end
Recv: >>> do_homing_move  X164.20 Y123.00 Z16.70
Recv: ...(Z, -375.00, [4.00])
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
[...]
Recv: <<< do_homing_move  X164.20 Y123.00 Z16.70
Recv: BLTouch STOW requested
Recv: BLTouch Command :90
Recv: bltouch.stow_proc() end
Recv: Move Away:
Recv: >>> do_homing_move  X164.20 Y123.00 Z16.70
Recv: ...(Z, 5.00, 4.00)
Recv: echo:busy: processing
[...]
Recv: <<< do_homing_move  X164.20 Y123.00 Z16.70
Recv: Home 2 Slow:
Recv: BLTouch DEPLOY requested
Recv: BLTouch Command :10
Recv: bltouch.deploy_proc() end
Recv: >>> do_homing_move  X164.20 Y123.00 Z16.70
Recv: ...(Z, -10.00, 2.00)
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
[...]
Recv: <<< do_homing_move  X164.20 Y123.00 Z16.70
Recv: BLTouch STOW requested
Recv: BLTouch Command :90
Recv: bltouch.stow_proc() end
Recv: >>> set_axis_is_at_home(Z)
Recv: *** Z HOMED WITH PROBE (Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) ***
Recv: > probe.offset.z = -1.70
Recv: Axis Z home_offset = 0.00 position_shift = 0.00
Recv: > home_offset[Z] = 0.00
Recv:   current_position= X164.20 Y123.00 Z1.70 :
Recv: <<< set_axis_is_at_home(Z)
Recv:   current_position= X164.20 Y123.00 Z1.70 : sync_plan_position
Recv:   current_position= X164.20 Y123.00 Z1.70 : > AFTER set_axis_is_at_home
Recv:   current_position= X164.20 Y123.00 Z1.70 : Probe::set_deployed
Recv: deploy: 0
Recv: Probe::do_z_raise(10.00)
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z1.70
Recv: >  X164.20 Y123.00 Z11.70
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z11.70
Recv: BLTouch STOW requested
Recv: BLTouch Command :90
Recv: bltouch.stow_proc() end
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z11.70
Recv: >  X164.20 Y123.00 Z11.70
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z11.70
Recv: <<< homeaxis(Z)
Recv: <<< home_z_safely  X164.20 Y123.00 Z11.70
Recv:   current_position= X164.20 Y123.00 Z11.70 : sync_plan_position
Recv: X:164.20 Y:123.00 Z:11.70 E:0.00 Count X:13136 Y:9840 Z:4680
Recv: <<< G28  X164.20 Y123.00 Z11.70
Recv: >>> Probe::probe_at_point  X164.20 Y123.00 Z5.00
Recv: ...(32.00, 32.00, raise, 0, probe_relative)
Recv:   current_position= X164.20 Y123.00 Z5.00 :
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z5.00
Recv: >  X79.20 Y38.00 Z5.00
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X79.20 Y38.00 Z5.00
Recv:   current_position= X79.20 Y38.00 Z5.00 : Probe::set_deployed
Recv: deploy: 1
Recv: Probe::do_z_raise(10.00)
Recv: >>> do_blocking_move_to  X79.20 Y38.00 Z5.00
Recv: >  X79.20 Y38.00 Z11.70
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X79.20 Y38.00 Z11.70
Recv: BLTouch DEPLOY requested
Recv: BLTouch Command :10
Recv: bltouch.deploy_proc() end
Recv: >>> do_blocking_move_to  X79.20 Y38.00 Z11.70
Recv: >  X79.20 Y38.00 Z11.70
Recv: <<< do_blocking_move_to  X79.20 Y38.00 Z11.70
Recv: >>> Probe::run_z_probe  X79.20 Y38.00 Z11.70
Recv: >>> Probe::probe_down_to_z  X79.20 Y38.00 Z11.70
Recv: BLTouch DEPLOY requested
Recv: BLTouch Command :10
Recv: bltouch.deploy_proc() end
Recv: >>> do_blocking_move_to  X79.20 Y38.00 Z11.70
Recv: >  X79.20 Y38.00 Z-0.30
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X79.20 Y38.00 Z-0.30
Recv: BLTouch STOW requested
Recv: BLTouch Command :90
Recv: bltouch.stow_proc() end
Recv:   current_position= X79.20 Y38.00 Z1.71 : sync_plan_position
Recv: <<< Probe::probe_down_to_z  X79.20 Y38.00 Z1.71
Recv: <<< Probe::run_z_probe  X79.20 Y38.00 Z1.71
Recv: >>> do_blocking_move_to  X79.20 Y38.00 Z1.71
Recv: >  X79.20 Y38.00 Z6.71
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X79.20 Y38.00 Z6.71
Recv: <<< Probe::probe_at_point  X79.20 Y38.00 Z6.71
Recv: Probing point 0 (Front-Left) X32.00 Y32.00 Z0.01
Recv: >>> Probe::probe_at_point  X79.20 Y38.00 Z5.00
Recv: ...(200.00, 32.00, raise, 0, probe_relative)
Recv:   current_position= X79.20 Y38.00 Z5.00 :
Recv: Position Not Reachable
Recv: <<< Probe::probe_at_point  X79.20 Y38.00 Z5.00
Recv: G35 failed at point 1 (Front-Right) X200.00 Y32.00
Recv: G35 aborted.
Recv:   current_position= X79.20 Y38.00 Z5.00 : Probe::set_deployed
Recv: deploy: 0
Recv: Probe::do_z_raise(10.00)
Recv: >>> do_blocking_move_to  X79.20 Y38.00 Z5.00
Recv: >  X79.20 Y38.00 Z11.70
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X79.20 Y38.00 Z11.70
Recv: BLTouch STOW requested
Recv: BLTouch Command :90
Recv: bltouch.stow_proc() end
Recv: >>> do_blocking_move_to  X79.20 Y38.00 Z11.70
Recv: >  X79.20 Y38.00 Z11.70
Recv: <<< do_blocking_move_to  X79.20 Y38.00 Z11.70
Recv: >>> set_axis_not_trusted(Z)
Recv: <<< set_axis_not_trusted(Z)
Recv: >>> G28  X79.20 Y38.00 Z11.70
Recv: Machine Type: Cartesian
Recv: Probe: BLTOUCH
Recv: Probe Offset X-47.20 Y-6.00 Z-1.70 (Left-Front & Below Nozzle)
Recv: Auto Bed Leveling: BILINEAR (disabled)
Recv:
Recv: Raise Z (before homing) by 5.00
Recv: >>> do_blocking_move_to  X79.20 Y38.00 Z11.70
Recv: >  X79.20 Y38.00 Z16.70
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X79.20 Y38.00 Z16.70
Recv: BLTouch Command :160
Recv: BLTouch Command :90
Recv: last_written_mode - 1
Recv: config mode - BLTOUCH_SET_5V_MODE
Recv: >>> home_z_safely  X79.20 Y38.00 Z16.70
Recv:   current_position= X79.20 Y38.00 Z16.70 : sync_plan_position
Recv:   destination= X164.20 Y123.00 Z18.40 : home_z_safely
Recv: >>> do_blocking_move_to  X79.20 Y38.00 Z16.70
Recv: >  X164.20 Y123.00 Z16.70
Recv: echo:busy: processing
[...]
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: >>> homeaxis(Z)
Recv:   current_position= X164.20 Y123.00 Z16.70 : Probe::set_deployed
Recv: deploy: 1
Recv: Probe::do_z_raise(10.00)
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: >  X164.20 Y123.00 Z16.70
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: BLTouch DEPLOY requested
Recv: BLTouch Command :10
Recv: bltouch.deploy_proc() end
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: >  X164.20 Y123.00 Z16.70
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z16.70
Recv: Home 1 Fast:
Recv: BLTouch DEPLOY requested
Recv: BLTouch Command :10
Recv: bltouch.deploy_proc() end
Recv: >>> do_homing_move  X164.20 Y123.00 Z16.70
Recv: ...(Z, -375.00, [4.00])
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
Recv: <<< do_homing_move  X164.20 Y123.00 Z16.70
Recv: BLTouch STOW requested
Recv: BLTouch Command :90
Recv: bltouch.stow_proc() end
Recv: Move Away:
Recv: >>> do_homing_move  X164.20 Y123.00 Z16.70
Recv: ...(Z, 5.00, 4.00)
Recv: echo:busy: processing
[...]
Recv: <<< do_homing_move  X164.20 Y123.00 Z16.70
Recv: Home 2 Slow:
Recv: BLTouch DEPLOY requested
Recv: BLTouch Command :10
Recv: bltouch.deploy_proc() end
Recv: >>> do_homing_move  X164.20 Y123.00 Z16.70
Recv: ...(Z, -10.00, 2.00)
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
Recv: <<< do_homing_move  X164.20 Y123.00 Z16.70
Recv: BLTouch STOW requested
Recv: BLTouch Command :90
Recv: bltouch.stow_proc() end
Recv: >>> set_axis_is_at_home(Z)
Recv: *** Z HOMED WITH PROBE (Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) ***
Recv: > probe.offset.z = -1.70
Recv: Axis Z home_offset = 0.00 position_shift = 0.00
Recv: > home_offset[Z] = 0.00
Recv:   current_position= X164.20 Y123.00 Z1.70 :
Recv: <<< set_axis_is_at_home(Z)
Recv:   current_position= X164.20 Y123.00 Z1.70 : sync_plan_position
Recv:   current_position= X164.20 Y123.00 Z1.70 : > AFTER set_axis_is_at_home
Recv:   current_position= X164.20 Y123.00 Z1.70 : Probe::set_deployed
Recv: deploy: 0
Recv: Probe::do_z_raise(10.00)
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z1.70
Recv: >  X164.20 Y123.00 Z11.70
[...]
Recv: echo:busy: processing
[...]
Recv: echo:busy: processing
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z11.70
Recv: BLTouch STOW requested
Recv: BLTouch Command :90
Recv: bltouch.stow_proc() end
Recv: >>> do_blocking_move_to  X164.20 Y123.00 Z11.70
Recv: >  X164.20 Y123.00 Z11.70
Recv: <<< do_blocking_move_to  X164.20 Y123.00 Z11.70
Recv: <<< homeaxis(Z)
Recv: <<< home_z_safely  X164.20 Y123.00 Z11.70
Recv:   current_position= X164.20 Y123.00 Z11.70 : sync_plan_position
Recv: X:164.20 Y:123.00 Z:11.70 E:0.00 Count X:13136 Y:9840 Z:4680
Recv: <<< G28  X164.20 Y123.00 Z11.70
Recv: <<< G35  X164.20 Y123.00 Z11.70
Recv: ok