bootvorgang


U-Boot 1.1.2 (Dec 22 2005 - 09:10:28)

U-Boot code: A3F80000 -> A3F97E1C  BSS: -> A3F9C554
RAM Configuration:
Bank #0: a0000000  0 kB
Bank #1: 00000000  0 kB
Bank #2: 00000000  0 kB
Bank #3: 00000000  0 kB
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
CPU speed: 312000kHz
Hit any key to stop autoboot:  0
## Booting image at 00080000 ...
Bad Magic Number
dm9000 i/o: 0x08000000, id: 0x90000a46
MAC: 00:14:2d:00:00:00
operating at 100M full duplex mode
BOOTP broadcast 1
DHCP client bound to address 192.168.1.199
TFTP from server 192.168.1.1; our IP address is 192.168.1.199
Filename '/images/uImage'.
Load address: 0xa1000000
Loading: #################################################################
         #################################################################
         #################################################################
         #########################
done
Bytes transferred = 1122954 (11228a hex)
## Booting image at a1000000 ...
   Image Name:   Linux Kernel Image
   Created:      2007-10-31  10:17:14 UTC
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    1122890 Bytes =  1.1 MB
   Load Address: a0008000
   Entry Point:  a0008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.12.4-col2-eos0 (root@pxadev) (gcc version 3.3.2) #2 Tue Oct 37
CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Machine: Toradex Colibri Module
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Run Mode clock: 208.00MHz (*16)
Turbo Mode clock: 312.00MHz (*1.5, active)
Memory clock: 208.00MHz (/2)
System bus clock: 208.00MHz
Built 1 zonelists
Kernel command line: root=/dev/nfs ip=:::::eth0: console=ttyS0,9600n8
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 62336KB available (1932K code, 384K data, 84K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
SCSI subsystem initialized
Linux Kernel Card Services
  options:  none
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
dm9000 Ethernet Driver
eth0: dm9000 at f4000000,f4000004 IRQ 146 MAC: 00:14:2d:00:00:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Probing Colibri flash at physical address 0x00000000 (32-bit buswidth)
Colibri flash: Found 2 x16 devices at 0x0 in 32-bit bank
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 3 MTD partitions on "Colibri flash":
0x00000000-0x00080000 : "Bootloader"
0x00080000-0x00480000 : "Kernel"
0x00480000-0x02000000 : "Filesystem"
Colibri PCMCIA
usbmon: debugs is not available
Setting port 3 power failed.
pxa27x-ohci pxa27x-ohci: PXA27x OHCI
pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1
pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
Colibri MMC/SD setup done.
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
eth0: link down
Sending BOOTP requests ..<6>eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
. OK
IP-Config: Got BOOTP answer from 192.168.1.1, my address is 192.168.1.199
IP-Config: Complete:
      device=eth0, addr=192.168.1.199, mask=255.255.255.0, gw=255.255.255.255,
     host=colibri, domain=fh-hagenberg.at, nis-domain=(none),
     bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=/root/pxadev/roots
Looking up port of RPC 100003/2 on 192.168.1.1
Looking up port of RPC 100005/1 on 192.168.1.1
VFS: Mounted root (nfs filesystem).
Freeing init memory: 84K
INIT: version 2.86 booting
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... done.
Starting portmap daemon: portmap.
Nothing to be done
INIT: Entering runlevel: 3
starting Busybox Periodic Command Scheduler: crond... done.
Starting PCMCIA services: cardmgr[1060]: cannot access /lib/modules/2.6.12.4-coy
cardmgr[1060]: watching 1 socket
done.
Starting syslogd/klogd: done
starting Busybox Telnet Daemon: telnetd... done.

Colibri OpenEmbedded Linux colibri ttyS0

colibri login: root
root@colibri:~# gdbserver localhost:1234 /home/RandomArm
Process /home/RandomArm created; pid = 1180
Listening on port 1234
Remote debugging from host 192.168.1.1
Killing inferior
root@colibri:~# /home/RandomArm
root@colibri:~# gdbserver localhost:1234 /home/RandomArm
Process /home/RandomArm created; pid = 1183
Listening on port 1234
Remote debugging from host 192.168.1.1

Child exited with retcode = 0

Child exited with status 0
GDBserver exiting
root@colibri:~#