;Lots of gcode before this that was omitted.

;TYPE:External perimeter
G1 F900
G1 X77.779 Y94.163 E.007
G1 X78.071 Y93.964 E.0092
G1 X78.939 Y93.54 E.02517
G1 X79.282 Y93.423 E.00945
G1 X79.668 Y93.362 E.01019
G1 X79.843 Y93.375 E.00457
G1 X79.897 Y93.411 E.0017
G1 X79.907 Y93.496 E.00224
G1 X79.861 Y93.623 E.0035
G1 X79.692 Y93.861 E.00763
G1 X79.285 Y94.283 E.01526
G1 X78.878 Y94.541 E.01255
G1 X78.72 Y94.611 E.00451
G1 X78.392 Y94.734 E.00913
G1 X78.03 Y94.806 E.00961
G1 X77.863 Y94.83 E.00439
G1 X77.651 Y94.806 E.00555
G1 X77.53 Y94.691 E.00435
G1 X77.58 Y94.42 E.00718
M204 P1000
G1 X77.87 Y94.343 F9000
; stop printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
;LAYER_CHANGE
;Z:102.95
;HEIGHT:0.149994
;BEFORE_LAYER_CHANGE
G92 E0.0
;102.95


G1 E-2.24 F4200
;WIPE_START
G1 F7200
G1 X77.779 Y94.163 E-.18045
G1 X78.071 Y93.964 E-.19566
G1 X78.939 Y93.54 E-.53523
G1 X78.94 Y93.539 E-.00067
;WIPE_END
G1 E-.048 F4200
G1 Z103 F720
;AFTER_LAYER_CHANGE
;102.95
; printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
G1 X78.005 Y94.198 F9000
G1 Z102.95 F720
G1 E3.2 F2400
M204 P800
G1 F900
G1 X78.139 Y94.053 E.00515
G1 X78.463 Y93.83 E.01023
G1 X79.324 Y93.436 E.02467
G1 X79.735 Y93.32 E.01113
G1 X79.849 Y93.305 E.00301
G1 X80.005 Y93.317 E.00408
G1 X80.078 Y93.369 E.00233
G1 X80.088 Y93.465 E.00251
G1 X79.979 Y93.656 E.00573
G1 X79.516 Y94.129 E.01725
G1 X79.207 Y94.321 E.00948
G1 X78.835 Y94.484 E.01057
G1 X78.752 Y94.516 E.00231
G1 X78.216 Y94.622 E.01426
G1 X77.987 Y94.613 E.00596
G1 X77.909 Y94.547 E.00265
G1 X77.972 Y94.248 E.00798
M204 P1000
G1 X78.203 Y94.195 F9000
G1 X78.191 Y94.304
;TYPE:Gap fill
;WIDTH:0.360837
G1 F900
G1 X78.649 Y94.156 E.00987
;WIDTH:0.364163
G1 X78.694 Y94.137 E.00099
;WIDTH:0.369616
G1 X79.03 Y93.986 E.00776
;WIDTH:0.369616
G1 X79.29 Y93.847 E.0062
;WIDTH:0.332723
G1 X79.509 Y93.693 E.00502
;WIDTH:0.300022
G1 X79.728 Y93.539 E.00447
; stop printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
;LAYER_CHANGE
;Z:103.1
;HEIGHT:0.150002
;BEFORE_LAYER_CHANGE
G92 E0.0
;103.1


G1 E-2.24 F4200
;WIPE_START
G1 F7200
G1 X79.509 Y93.693 E-.14843
;WIPE_END
G1 E-.81157 F4200
G1 Z103.15 F720
;AFTER_LAYER_CHANGE
;103.1
; printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
G1 X78.323 Y94.292 F9000
G1 Z103.1 F720
G1 E3.2 F2400
M204 P800
;TYPE:External perimeter
;WIDTH:0.45
G1 F900
G1 X78.345 Y94.188 E.00276
G1 X78.515 Y93.935 E.00795
G1 X78.901 Y93.697 E.01182
G1 X79.767 Y93.336 E.02444
G1 X79.98 Y93.289 E.00568
G1 X80.167 Y93.294 E.00489
G1 X80.237 Y93.363 E.00256
G1 X80.179 Y93.499 E.00384
G1 X79.979 Y93.749 E.00834
G1 X79.714 Y93.99 E.00934
G1 X79.52 Y94.103 E.00584
G1 X79.144 Y94.267 E.0107
G1 X78.613 Y94.395 E.01423
G1 X78.366 Y94.377 E.00643
G1 X78.342 Y94.349 E.00097
M204 P1000
G1 X78.397 Y94.217 F9000
G1 X78.624 Y94.147
;TYPE:Gap fill
;WIDTH:0.153764
G1 F900
G1 X78.764 Y94.089 E.00115
;WIDTH:0.193904
G1 X78.905 Y94.031 E.00153
;WIDTH:0.234044
G1 X79.045 Y93.972 E.00191
;WIDTH:0.234462
G1 X79.047 Y93.971 E.00004
;WIDTH:0.239966
G1 X79.351 Y93.835 E.00431
;WIDTH:0.239967
G1 X79.378 Y93.824 E.00038
;WIDTH:0.238866
G1 X79.536 Y93.748 E.00225
;WIDTH:0.211914
G1 X79.624 Y93.692 E.00117
;WIDTH:0.174151
G1 X79.713 Y93.637 E.00092
;WIDTH:0.136388
G1 X79.802 Y93.582 E.00068
;WIDTH:0.0986236
G1 X79.843 Y93.552 E.00021
; stop printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
;LAYER_CHANGE
;Z:103.25
;HEIGHT:0.150002
;BEFORE_LAYER_CHANGE
G92 E0.0
;103.25


G1 E-2.24 F4200
;WIPE_START
G1 F7200
G1 X79.802 Y93.582 E-.02837
;WIPE_END
G1 E-.93163 F4200
G1 Z103.3 F720
;AFTER_LAYER_CHANGE
;103.25
; printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
G1 X80.214 Y93.318 F9000
G1 Z103.25 F720
G1 E3.2 F2400
M204 P800
;TYPE:External perimeter
;WIDTH:0.45
G1 F900
G1 X80.257 Y93.412 E.00269
G1 X80.169 Y93.581 E.00495
G1 X80.123 Y93.638 E.00192
G1 X79.93 Y93.788 E.00637
G1 X79.591 Y93.974 E.01007
G1 X79.071 Y94.123 E.0141
G1 X78.838 Y94.126 E.00607
G1 X78.809 Y94.032 E.00257
G1 X78.998 Y93.782 E.00817
G1 X79.372 Y93.566 E.01126
G1 X79.743 Y93.42 E.01039
G1 X80.154 Y93.321 E.01099
M204 P1000
G1 X80.199 Y93.421 F9000
; stop printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
;LAYER_CHANGE
;Z:103.4
;HEIGHT:0.150002
;BEFORE_LAYER_CHANGE
G92 E0.0
;103.4


G1 E-2.24 F4200
;WIPE_START
G1 F7200
G1 X80.257 Y93.412 E-.07647
G1 X80.169 Y93.581 E-.10535
G1 X80.123 Y93.638 E-.04074
G1 X79.93 Y93.788 E-.13542
G1 X79.591 Y93.974 E-.21417
G1 X79.071 Y94.123 E-.29989
G1 X78.999 Y94.124 E-.03996
;WIPE_END
G1 E-.048 F4200
G1 Z103.45 F720
;AFTER_LAYER_CHANGE
;103.4
; printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
G1 X80.186 Y93.48 F9000
G1 Z103.4 F720
G1 E3.2 F2400
M204 P800
G1 F900
G1 X80.074 Y93.591 E.00411
G1 X79.819 Y93.722 E.00748
G1 X79.636 Y93.782 E.00503
G1 X79.394 Y93.81 E.00635
G1 X79.602 Y93.613 E.00748
G1 X79.899 Y93.465 E.00865
G1 X80.019 Y93.433 E.00323
G1 X80.161 Y93.425 E.0037
M204 P1000
G1 X80.048 Y93.556 F9000
; stop printing object red-dragon-ancient-updated-right-wing.stl id:0 copy 0
G1 E-2.24 F4200
;WIPE_START
G1 F7200;_WIPE
G1 X80.074 Y93.591 E-.10324
G1 F7200;_WIPE
G1 X79.819 Y93.722 E-.15899
G1 F7200;_WIPE
G1 X79.636 Y93.782 E-.10706
G1 F7200;_WIPE
G1 X79.394 Y93.81 E-.135
G1 F7200;_WIPE
G1 X79.602 Y93.613 E-.15911
G1 F7200;_WIPE
G1 X79.899 Y93.465 E-.18389
G1 F7200;_WIPE
G1 X80.012 Y93.435 E-.0647
;WIPE_END
G1 E-.048 F4200
G1 Z103.6 F720
M107
;TYPE:Custom
; Filament-specific end gcode
G1 E-1 F2100 ; retract
G1 Z105.4 F720 ; Move print head up
G1 X178 Y178 F4200 ; park print head
G1 Z133.4 F720 ; Move print head further up
G4 ; wait
M104 S0 ; turn off temperature
M140 S0 ; turn off heatbed
M107 ; turn off fan
M221 S100 ; reset flow
M900 K0 ; reset LA
M84 ; disable motors
M73 P100 R0
; filament used [mm] = 21051.35
; filament used [cm3] = 50.63
; filament used [g] = 62.79
; filament cost = 1.90
; total filament used [g] = 62.79
; total filament cost = 1.90
; estimated printing time (normal mode) = 9h 41m 29s

; prusaslicer_config = begin
; avoid_crossing_perimeters = 0
; avoid_crossing_perimeters_max_detour = 0
; bed_custom_model =
; bed_custom_texture =
; bed_shape = 0x0,180x0,180x180,0x180
; bed_temperature = 60
; before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
; between_objects_gcode =
; bottom_fill_pattern = monotonic
; bottom_solid_layers = 5
; bottom_solid_min_thickness = 0.5
; bridge_acceleration = 1000
; bridge_angle = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 1
; bridge_speed = 25
; brim_separation = 0.1
; brim_type = outer_only
; brim_width = 0
; clip_multipart_objects = 1
; color_change_gcode = M600
; compatible_printers_condition_cummulative = "printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.4";"nozzle_diameter[0]!=0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)"
; complete_objects = 0
; cooling = 1
; cooling_tube_length = 5
; cooling_tube_retraction = 91.5
; default_acceleration = 1000
; default_filament_profile = "Prusament PLA"
; default_print_profile = 0.15mm QUALITY @MINI
; deretract_speed = 40
; disable_fan_first_layers = 1
; dont_support_bridges = 0
; draft_shield = disabled
; duplicate_distance = 6
; elefant_foot_compensation = 0.2
; end_filament_gcode = "; Filament-specific end gcode"
; end_gcode = G1 E-1 F2100 ; retract\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F720 ; Move print head up{endif}\nG1 X178 Y178 F4200 ; park print head\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)} F720 ; Move print head further up{endif}\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM221 S100 ; reset flow\nM900 K0 ; reset LA\nM84 ; disable motors
; ensure_vertical_shell_thickness = 1
; external_perimeter_extrusion_width = 0.45
; external_perimeter_speed = 30
; external_perimeters_first = 0
; extra_loading_move = -2
; extra_perimeters = 0
; extruder_clearance_height = 20
; extruder_clearance_radius = 35
; extruder_colour = ""
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1
; extrusion_width = 0.45
; fan_always_on = 1
; fan_below_layer_time = 100
; filament_colour = #FF8000
; filament_cooling_final_speed = 3.4
; filament_cooling_initial_speed = 2.2
; filament_cooling_moves = 4
; filament_cost = 30.24
; filament_density = 1.24
; filament_diameter = 1.75
; filament_load_time = 0
; filament_loading_speed = 28
; filament_loading_speed_start = 3
; filament_max_volumetric_speed = 15
; filament_minimal_purge_on_wipe_tower = 15
; filament_notes = "Affordable filament for everyday printing in premium quality manufactured in-house by Josef Prusa"
; filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
; filament_settings_id = "Prusament PLA"
; filament_soluble = 0
; filament_spool_weight = 201
; filament_toolchange_delay = 0
; filament_type = PLA
; filament_unload_time = 0
; filament_unloading_speed = 90
; filament_unloading_speed_start = 100
; filament_vendor = Prusa Polymers
; fill_angle = 45
; fill_density = 15%
; fill_pattern = gyroid
; first_layer_acceleration = 800
; first_layer_acceleration_over_raft = 0
; first_layer_bed_temperature = 60
; first_layer_extrusion_width = 0.42
; first_layer_height = 0.2
; first_layer_speed = 20
; first_layer_speed_over_raft = 30
; first_layer_temperature = 215
; full_fan_speed_layer = 4
; fuzzy_skin = none
; fuzzy_skin_point_dist = 0.8
; fuzzy_skin_thickness = 0.3
; gap_fill_enabled = 1
; gap_fill_speed = 40
; gcode_comments = 0
; gcode_flavor = marlin2
; gcode_label_objects = 1
; gcode_resolution = 0.0125
; high_current_on_filament_swap = 0
; host_type = octoprint
; infill_acceleration = 1000
; infill_anchor = 2.5
; infill_anchor_max = 12
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0.45
; infill_first = 0
; infill_only_where_needed = 0
; infill_overlap = 25%
; infill_speed = 80
; interface_shells = 0
; ironing = 0
; ironing_flowrate = 15%
; ironing_spacing = 0.1
; ironing_speed = 15
; ironing_type = top
; layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
; layer_height = 0.15
; machine_limits_usage = emit_to_gcode
; machine_max_acceleration_e = 5000
; machine_max_acceleration_extruding = 1250
; machine_max_acceleration_retracting = 1250
; machine_max_acceleration_travel = 2500
; machine_max_acceleration_x = 2500
; machine_max_acceleration_y = 2500
; machine_max_acceleration_z = 400
; machine_max_feedrate_e = 80
; machine_max_feedrate_x = 180
; machine_max_feedrate_y = 180
; machine_max_feedrate_z = 12
; machine_max_jerk_e = 10
; machine_max_jerk_x = 8
; machine_max_jerk_y = 8
; machine_max_jerk_z = 2
; machine_min_extruding_rate = 0
; machine_min_travel_rate = 0
; max_fan_speed = 100
; max_layer_height = 0.25
; max_print_height = 180
; max_print_speed = 150
; max_volumetric_speed = 0
; min_fan_speed = 100
; min_layer_height = 0.07
; min_print_speed = 15
; min_skirt_length = 4
; mmu_segmented_region_max_width = 0
; notes =
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 0
; ooze_prevention = 0
; output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
; overhangs = 1
; parking_pos_retraction = 92
; pause_print_gcode = M601
; perimeter_acceleration = 800
; perimeter_extruder = 1
; perimeter_extrusion_width = 0.45
; perimeter_speed = 40
; perimeters = 4
; physical_printer_settings_id =
; post_process =
; print_settings_id = 0.15mm QUALITY @MINI
; printer_model = MINI
; printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MINI\n
; printer_settings_id = Original Prusa MINI & MINI+
; printer_technology = FFF
; printer_variant = 0.4
; printer_vendor =
; raft_contact_distance = 0.2
; raft_expansion = 1.5
; raft_first_layer_density = 90%
; raft_first_layer_expansion = 3
; raft_layers = 0
; remaining_times = 1
; resolution = 0
; retract_before_travel = 1.5
; retract_before_wipe = 70%
; retract_layer_change = 1
; retract_length = 3.2
; retract_length_toolchange = 4
; retract_lift = 0.2
; retract_lift_above = 0
; retract_lift_below = 179
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 70
; seam_position = nearest
; silent_mode = 0
; single_extruder_multi_material = 0
; single_extruder_multi_material_priming = 1
; skirt_distance = 2
; skirt_height = 3
; skirts = 1
; slice_closing_radius = 0.049
; slicing_mode = regular
; slowdown_below_layer_time = 15
; small_perimeter_speed = 25
; solid_infill_below_area = 0
; solid_infill_every_layers = 0
; solid_infill_extruder = 1
; solid_infill_extrusion_width = 0.45
; solid_infill_speed = 80
; spiral_vase = 0
; standby_temperature_delta = -5
; start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
; start_gcode = M862.3 P "[printer_model]" ; printer model check\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S170 ; set extruder temp for bed leveling\nM140 S[first_layer_bed_temperature] ; set bed temp\nM109 R170 ; wait for bed leveling temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM204 T1250 ; set travel acceleration\nG28 ; home all without mesh bed level\nG29 ; mesh bed leveling \nM204 T[machine_max_acceleration_travel] ; restore travel acceleration\nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0\nG1 Y-2 X179 F2400\nG1 Z3 F720\nM109 S[first_layer_temperature] ; wait for extruder temp\n\n; intro line\nG1 X170 F1000\nG1 Z0.2 F720\nG1 X110 E8 F900\nG1 X40 E10 F700\nG92 E0\n\nM221 S95 ; set flow
; support_material = 1
; support_material_angle = 0
; support_material_auto = 1
; support_material_bottom_contact_distance = 0
; support_material_bottom_interface_layers = 0
; support_material_buildplate_only = 1
; support_material_closing_radius = 2
; support_material_contact_distance = 0.2
; support_material_enforce_layers = 0
; support_material_extruder = 0
; support_material_extrusion_width = 0.35
; support_material_interface_contact_loops = 0
; support_material_interface_extruder = 0
; support_material_interface_layers = 2
; support_material_interface_pattern = rectilinear
; support_material_interface_spacing = 0.2
; support_material_interface_speed = 80%
; support_material_pattern = rectilinear
; support_material_spacing = 2
; support_material_speed = 40
; support_material_style = grid
; support_material_synchronize_layers = 0
; support_material_threshold = 50
; support_material_with_sheath = 0
; support_material_xy_spacing = 60%
; temperature = 215
; template_custom_gcode =
; thick_bridges = 0
; thin_walls = 0
; threads = 24
; thumbnails = 16x16,220x124
; toolchange_gcode =
; top_fill_pattern = monotonic
; top_infill_extrusion_width = 0.4
; top_solid_infill_speed = 40
; top_solid_layers = 8
; top_solid_min_thickness = 0.7
; travel_speed = 150
; travel_speed_z = 12
; use_firmware_retraction = 0
; use_relative_e_distances = 1
; use_volumetric_e = 0
; variable_layer_height = 1
; wipe = 1
; wipe_into_infill = 0
; wipe_into_objects = 0
; wipe_tower = 0
; wipe_tower_bridging = 10
; wipe_tower_brim_width = 2
; wipe_tower_no_sparse_layers = 0
; wipe_tower_rotation_angle = 0
; wipe_tower_width = 60
; wipe_tower_x = 170
; wipe_tower_y = 140
; wiping_volumes_extruders = 70,70
; wiping_volumes_matrix = 0
; xy_size_compensation = 0
; z_offset = 0
; prusaslicer_config = end