API tools faq
paste
Guest User

Nas540_without_disks

a guest
Apr 22nd, 2022
52
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 45.61 KB | None | 0 0
raw download clone embed print report
  1.  
  2.  
  3. uloader 2011.06.0 (May 20 2014 - 16:36:41)
  4.  
  5. Board: Mindspeed C2000
  6. c2k_spi_probe
  7.  
  8. Copying Barebox from SPI Flash(bootopt=0)
  9. BB Copying Done
  10. ## Starting Barebox at 0x01000000 ...
  11.  
  12.  
  13. barebox 2011.06.0-svn44305-dirty6 (Aug 28 2014 - 22:25:22)
  14.  
  15. Board: Mindspeed C2000
  16. c2k_spi_probe
  17. c2k_otp_probe.
  18. cbus_baseaddr: 9c000000, ddr_baseaddr: 03800000, ddr_phys_baseaddr: 03800000
  19. class init complete
  20. tmu init complete
  21. bmu1 init: done
  22. bmu2 init: done
  23. util init complete
  24. GPI1 init complete
  25. GPI2 init complete
  26. HGPI init complete
  27. HIF rx desc: base_va: 03e80000, base_pa: 03e80000
  28. HIF tx desc: base_va: 03e80400, base_pa: 03e80400
  29. HIF init complete
  30. bmu1 enabled
  31. bmu2 enabled
  32. pfe_hw_init: done
  33. pfe_firmware_init
  34. pfe_load_elf
  35. pfe_load_elf no of sections: 10
  36. pfe_firmware_init: class firmware loaded
  37. pfe_load_elf
  38. pfe_load_elf no of sections: 10
  39. pfe_firmware_init: tmu firmware loaded
  40. pfe_load_elf
  41. pfe_load_elf no of sections: 14
  42. pfe_firmware_init: util firmware loaded
  43. eth_port: 0
  44. NAS540_phy_reg_setting[eth_port].phyaddr: 0x4
  45. miidev_restart_aneg for PHY4
  46. eth_port: 1
  47. NAS540_phy_reg_setting[eth_port].phyaddr: 0x6
  48. miidev_restart_aneg for PHY6
  49. cfi_probe: cfi_flash base: 0xc0000000 size: 0x04000000
  50. ## Unknown FLASH on Bank at 0xc0000000 - Size = 0x00000000 = 0 MB
  51. bootopt = 0x0
  52. Using ENV from SPI Flash.
  53. nand_probe: comcerto_nand base: 0xc8300000 size: 0x256 MB
  54. NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
  55. Using default values
  56. Bad block table not found for chip 0
  57. Bad block table not found for chip 0
  58. Scanning device for bad blocks
  59. Bad block table written to 0x0ffe0000, version 0x01
  60. Bad block table written to 0x0ffc0000, version 0x01
  61. Malloc space: 0x00600000 -> 0x01000000 (size 10 MB)
  62. Stack space : 0x005f8000 -> 0x00600000 (size 32 kB)
  63. running /env/bin/init...
  64. Unknown command 'export' - try 'help'
  65. Disabling eee function of phy 4 ...
  66. Disabling eee function of phy 6 ...
  67.  
  68. Hit any key to stop autoboot: 1
  69. booting kernel of type uimage from /dev/nand0.kernel2.bb
  70. Verifying Checksum ... OK
  71. Image Name: Linux-3.2.54
  72. Created: 2018-05-21 17:36:47 UTC
  73. Image Type: <NULL> <NULL> <NULL> (<NULL>)
  74. Data Size: 7311656 Bytes = 7 MB
  75. Load Address: 0f008000
  76. Entry Point: 0f008000
  77. OK
  78.  
  79. Starting kernel ...
  80.  
  81. commandline: console=ttyS0,115200n8, init=/etc/preinit pcie_gen1_only=yes mac_addr=,, ip=dhcp root=ubi0:rootfs ubi.mtd=2,2048 rootfstype=ubifs rw noinitrd mtdparts=spi0.0:256k(uloader)ro,512k(barebox)ro,256k(env);comcertonand:10M(config),10M(kernel1),110M(rootfs1),10M(kernel2),110M(rootfs2),-(reserved) usb3_internal_clk=yes
  82. arch_number: 1094
  83. Uncompressing Linux... done, booting the kernel.
  84. [ 0.000000] Booting Linux on physical CPU 0
  85. [ 0.000000] Initializing cgroup subsys cpuset
  86. [ 0.000000] Linux version 3.2.54 (root@SDD2SVR2) (gcc version 4.8.5 20150209 (prerelease) (crosstool-NG 1.21.0) ) #1 SMP Tue May 22 01:36:44 CST 2018
  87. [ 0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=50c53c7d
  88. [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  89. [ 0.000000] Machine: Comcerto 2000 EVM
  90. [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
  91. [ 0.000000] Comcerto: zone_dma mapping size=2c00000 type=b
  92. [ 0.000000] PERCPU: Embedded 8 pages/cpu @8524c000 s9504 r8192 d15072 u32768
  93. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 254976
  94. [ 0.000000] Kernel command line: console=ttyS0,115200n8, init=/etc/preinit pcie_gen1_only=yes mac_addr=,, ip=dhcp root=ubi0:rootfs ubi.mtd=2,2048 rootfstype=ubifs rw noinitrd mtdparts=spi0.0:256k(uloader)ro,512k(barebox)ro,256k(env);comcertonand:10M(config),10M(kernel1),110M(rootfs1),10M(kernel2),110M(rootfs2),-(reserved) usb3_internal_clk=yes
  95. [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  96. [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  97. [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  98. [ 0.000000] Memory: 44MB 960MB = 1004MB total
  99. [ 0.000000] Memory: 1008508k/1008508k available, 40068k reserved, 0K highmem
  100. [ 0.000000] Virtual kernel memory layout:
  101. [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  102. [ 0.000000] fixmap : 0xfff30000 - 0xfffe0000 ( 704 kB)
  103. [ 0.000000] vmalloc : 0xc0800000 - 0xf0000000 ( 760 MB)
  104. [ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB)
  105. [ 0.000000] modules : 0x83600000 - 0x84000000 ( 10 MB)
  106. [ 0.000000] .text : 0x84008000 - 0x8468b460 (6670 kB)
  107. [ 0.000000] .init : 0x8468c000 - 0x8499a520 (3130 kB)
  108. [ 0.000000] .data : 0x8499c000 - 0x849e4bb0 ( 291 kB)
  109. [ 0.000000] .bss : 0x849e4bd4 - 0x84a45218 ( 386 kB)
  110. [ 0.000000] Hierarchical RCU implementation.
  111. [ 0.000000] NR_IRQS:256
  112. [ 0.000000] PLL0 running at 2400 MHz, PLL1 at 1000 MHz PLL2 running at 1500 MHz PLL3 running at 1066 MHz
  113. [ 0.000000] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 17179ms
  114. [ 0.000192] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
  115. [ 0.090048] pid_max: default: 32768 minimum: 301
  116. [ 0.090252] Mount-cache hash table entries: 512
  117. [ 0.090784] Initializing cgroup subsys cpuacct
  118. [ 0.090817] Initializing cgroup subsys devices
  119. [ 0.090852] CPU: Testing write buffer coherency: ok
  120. [ 0.091016] CPU0: thread -1, cpu 0, socket 9, mpidr 80000900
  121. [ 0.091045] Calibrating local timer... 299.89MHz.
  122. [ 0.150075] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  123. [ 0.151171] CPU1 powered up
  124. [ 0.151769] CPU1: Booted secondary processor
  125. [ 0.190048] CPU1: thread -1, cpu 1, socket 9, mpidr 80000901
  126. [ 0.190100] Brought up 2 CPUs
  127. [ 0.190112] SMP: Total of 2 processors activated (2393.70 BogoMIPS).
  128. [ 0.191632] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
  129. [ 0.192017] xor: measuring software checksum speed
  130. [ 0.240011] arm4regs : 2130.000 MB/sec
  131. [ 0.289993] 8regs : 1397.600 MB/sec
  132. [ 0.339975] 32regs : 1186.400 MB/sec
  133. [ 0.389968] neon : 1384.000 MB/sec
  134. [ 0.389975] xor: using function: arm4regs (2130.000 MB/sec)
  135. [ 0.390162] NET: Registered protocol family 16
  136. [ 0.391902] L310 cache controller enabled
  137. [ 0.391916] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x00c40000, PREFETCH_CTRL 0x00000000, Cache size: 262144 B
  138. [ 0.391996] ARMv7 AUX CTRL(0): 0x41
  139. [ 0.392001] ARMv7 AUX CTRL(0): 0x41
  140. [ 0.392017] ARMv7 AUX CTRL(1): 0x41
  141. [ 0.392025] ARMv7 AUX CTRL(1): 0x41
  142. [ 0.392949] Pin Select for GPIO[15:0]: 05000000
  143. [ 0.392956] Pin Select for GPIO[31:16]: 00555540
  144. [ 0.392962] Output Enable for GPIO[31:0]: DFFFFF00
  145. [ 0.392967] Pin Select for GPIO[59:32]: 0FFFFFFE
  146. [ 0.392972] Pin Select for GPIO[63:60]: 00000020
  147. [ 0.392978] Output Enable for GPIO[63:32]: 00000001
  148. [ 0.392984] Enable USB ...
  149. [ 0.394271] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
  150. [ 0.394281] hw-breakpoint: maximum watchpoint size is 4 bytes.
  151. [ 0.394297] Power Management Mode Support For C2000:
  152. [ 0.394661] PCIe: Ref clk 48Mhz
  153. [ 0.394668] PCIe: Detected C2K RevA1 device serdes clk devider old:new=2e:6
  154. [ 0.411036] PCIe0: Link Up Success
  155. [ 0.411042] PCIe0: Polarity: 0 Gen1 mode: 1 External Clk: 0
  156. [ 0.411048] comcerto_pcie_rc_int_init
  157. [ 0.411458] PCI: bus0: Fast back to back transfers disabled
  158. [ 0.411640] pci 0000:00:00.0: BAR 6: assigned [mem 0xa0000000-0xa000ffff pref]
  159. [ 0.411652] pci 0000:00:00.0: BAR 5: assigned [mem 0xa0010000-0xa00101ff]
  160. [ 0.411664] pci 0000:00:00.0: BAR 5: set to [mem 0xa0010000-0xa00101ff] (PCI address [0xa0010000-0xa00101ff])
  161. [ 0.438356] bio: create slab <bio-0> at 0
  162. [ 0.601070] raid6: int32x1 32 MB/s
  163. [ 0.770572] raid6: int32x2 49 MB/s
  164. [ 0.940147] raid6: int32x4 84 MB/s
  165. [ 1.110059] raid6: int32x8 119 MB/s
  166. [ 1.280069] raid6: neonx1 144 MB/s
  167. [ 1.449965] raid6: neonx2 177 MB/s
  168. [ 1.619790] raid6: neonx4 199 MB/s
  169. [ 1.789738] raid6: neonx8 201 MB/s
  170. [ 1.789745] raid6: using algorithm neonx8 (201 MB/s)
  171. [ 1.790040] vgaarb: loaded
  172. [ 1.790594] SCSI subsystem initialized
  173. [ 1.791479] usbcore: registered new interface driver usbfs
  174. [ 1.791708] usbcore: registered new interface driver hub
  175. [ 1.791865] usbcore: registered new device driver usb
  176. [ 1.792901] Switching to clocksource timer2
  177. [ 1.802682] NET: Registered protocol family 2
  178. [ 1.802899] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  179. [ 1.803675] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  180. [ 1.805033] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
  181. [ 1.805676] TCP: Hash tables configured (established 131072 bind 65536)
  182. [ 1.805684] TCP reno registered
  183. [ 1.805696] UDP hash table entries: 512 (order: 2, 16384 bytes)
  184. [ 1.805751] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  185. [ 1.806105] NET: Registered protocol family 1
  186. [ 1.806407] RPC: Registered named UNIX socket transport module.
  187. [ 1.806414] RPC: Registered udp transport module.
  188. [ 1.806420] RPC: Registered tcp transport module.
  189. [ 1.806425] RPC: Registered tcp NFSv4.1 backchannel transport module.
  190. [ 2.035799] gpio_dev = fd00000
  191. [ 2.036072] membuf_init: created membuf device(252, 0)
  192. [ 2.036141] clock_frequency_set: (1:24) NTG INCR value is 422212465
  193. [ 2.067650] VFS: Disk quotas dquot_6.5.2
  194. [ 2.067808] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  195. [ 2.068483] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  196. [ 2.068492] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
  197. [ 2.069103] fuse init (API version 7.17)
  198. [ 2.072542] Btrfs loaded
  199. [ 2.072573] msgmni has been set to 1969
  200. [ 2.078033] async_tx: api initialized (async)
  201. [ 2.078472] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
  202. [ 2.078486] io scheduler noop registered
  203. [ 2.078492] io scheduler deadline registered
  204. [ 2.078592] io scheduler cfq registered (default)
  205. [ 2.084613] ### comcerto_dma_probe: XOR DMA channel registered
  206. [ 2.090192] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  207. [ 2.233341] 84a386a0 849af858 0 ffffffff
  208. [ 2.234294] serial8250 serial8250.0: Couldn't set LCR to 191
  209. [ 2.235812] serial8250 serial8250.0: Couldn't set LCR to 191
  210. [ 2.237767] serial8250 serial8250.0: Couldn't set LCR to 224
  211. [ 2.239044] serial8250 serial8250.0: Couldn't set LCR to 224
  212. [ 2.259079] serial8250.0: ttyS0 at MMIO 0x96400000 (irq = 59) is a 16550A
  213. [ 2.965577] console [ttyS0] enabled
  214. [ 2.998664] comcerto_otp_probe.
  215. [ 3.052272] loop: module loaded
  216. [ 3.068361] PCI: enabling device 0000:00:00.0 (0140 -> 0142)
  217. [ 3.074191] ahci: SSS flag set, parallel bus scan disabled
  218. [ 3.079735] ahci 0000:00:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
  219. [ 3.087882] ahci 0000:00:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
  220. [ 3.113869] scsi0 : ahci
  221. [ 3.122984] scsi1 : ahci
  222. [ 3.126429] ata1: SATA max UDMA/133 abar m512@0xa0010000 port 0xa0010100 irq 96
  223. [ 3.133811] ata2: SATA max UDMA/133 abar m512@0xa0010000 port 0xa0010180 irq 96
  224. [ 3.146432] SATA Serdes: 48Mhz ref clk
  225. [ 3.150683] Serdes1: Lane OK Passed
  226. [ 3.154686] Serdes2: Lane OK Passed
  227. [ 3.158189] ahci ahci: forcing PORTS_IMPL to 0x3
  228. [ 3.162879] ahci ahci: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x3 impl platform mode
  229. [ 3.170679] ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
  230. [ 3.194992] scsi2 : ahci_platform
  231. [ 3.204178] scsi3 : ahci_platform
  232. [ 3.209286] ata3: SATA max UDMA/133 mmio [mem 0x9d000000-0x9d00ffff] port 0x100 irq 48
  233. [ 3.217267] ata4: SATA max UDMA/133 mmio [mem 0x9d000000-0x9d00ffff] port 0x180 irq 48
  234. [ 3.225971] designware_spi_probe:Initializing SPI Controller : Using dma=0 CLK(DUS)=250000000 Hz
  235. [ 3.237141] comcerto_spi comcerto_spi.1: at 0x96500000 mapped to 0xC080A000, irq=60
  236. [ 3.244878] designware_spi_probe:Initializing SPI Controller : Using dma=0 CLK(spi_i2c)=250000000 Hz
  237. [ 3.266681] comcerto_spi comcerto_spi.0: at 0x90498000 mapped to 0xC080C000, irq=61
  238. [ 3.291493] comcertoflash: probe of comcertoflash.0 failed with error -5
  239. [ 3.300551] m25p80 spi0.0: found mx25l8005, expected s25fl256s0
  240. [ 3.306537] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
  241. [ 3.311365] 3 cmdlinepart partitions found on MTD device spi0.0
  242. [ 3.317316] Creating 3 MTD partitions on "spi0.0":
  243. [ 3.322122] 0x000000000000-0x000000040000 : "uloader"
  244. [ 3.338761] 0x000000040000-0x0000000c0000 : "barebox"
  245. [ 3.354749] 0x0000000c0000-0x000000100000 : "env"
  246. [ 3.372674] pdev->resource->start = c8300000, pdev->resource->end = c8301fff
  247. [ 3.379801] nand_probe: comcertonand base: 0xc0800000
  248. [ 3.384986] ONFI flash detected
  249. [ 3.388213] ONFI param page 0 valid
  250. [ 3.391713] NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD S34ML02G1)
  251. [ 3.398883] hw_syndrome correction 2048.
  252. [ 3.402815] Using default values for hw ecc
  253. [ 3.410309] Bad block table not found for chip 0
  254. [ 3.418187] Bad block table not found for chip 0
  255. [ 3.422815] Scanning device for bad blocks
  256. [ 3.482963] ata1: SATA link down (SStatus 0 SControl 320)
  257. [ 3.504582] Bad block table written to 0x00000ffe0000, version 0x01
  258. [ 3.512697] Bad block table written to 0x00000ffc0000, version 0x01
  259. [ 3.519011] 6 cmdlinepart partitions found on MTD device comcertonand
  260. [ 3.525476] Creating 6 MTD partitions on "comcertonand":
  261. [ 3.530806] 0x000000000000-0x000000a00000 : "config"
  262. [ 3.542272] 0x000000a00000-0x000001400000 : "kernel1"
  263. [ 3.558484] 0x000001400000-0x000008200000 : "rootfs1"
  264. [ 3.569997] 0x000008200000-0x000008c00000 : "kernel2"
  265. [ 3.575247] ata4: SATA link down (SStatus 0 SControl 320)
  266. [ 3.580702] ata3: SATA link down (SStatus 0 SControl 320)
  267. [ 3.594018] 0x000008c00000-0x00000fa00000 : "rootfs2"
  268. [ 3.610208] 0x00000fa00000-0x000010000000 : "reserved"
  269. [ 3.637041] Fixed MDIO Bus: probed
  270. [ 3.641292] ## xhci_plat_probe
  271. [ 3.644398] ### comcerto_start_xhci
  272. [ 3.647906] USB3.0 clock selected: internal
  273. [ 3.655349] xhci-hcd xhci-hcd: xHCI Host Controller
  274. [ 3.660336] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
  275. [ 3.667571] xhci-hcd xhci-hcd: irq 54, io mem 0x9f000000
  276. [ 3.672999] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  277. [ 3.679814] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  278. [ 3.687080] usb usb1: Product: xHCI Host Controller
  279. [ 3.691971] usb usb1: Manufacturer: Linux 3.2.54 xhci-hcd
  280. [ 3.697397] usb usb1: SerialNumber: xhci-hcd
  281. [ 3.702778] hub 1-0:1.0: USB hub found
  282. [ 3.706620] hub 1-0:1.0: 1 port detected
  283. [ 3.715355] xhci-hcd xhci-hcd: xHCI Host Controller
  284. [ 3.720324] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
  285. [ 3.720540] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
  286. [ 3.720547] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  287. [ 3.720554] usb usb2: Product: xHCI Host Controller
  288. [ 3.720559] usb usb2: Manufacturer: Linux 3.2.54 xhci-hcd
  289. [ 3.720564] usb usb2: SerialNumber: xhci-hcd
  290. [ 3.725075] hub 2-0:1.0: USB hub found
  291. [ 3.725095] hub 2-0:1.0: 1 port detected
  292. [ 3.743084] usbcore: registered new interface driver usblp
  293. [ 3.743092] Initializing USB Mass Storage driver...
  294. [ 3.753613] usbcore: registered new interface driver usb-storage
  295. [ 3.753619] USB Mass Storage support registered.
  296. [ 3.753625] dwc_otg: version 2.94a 27-OCT-2011
  297. hotplug394add:
  298. hotplug397add:
  299. hotplug395add:9
  300. [ 3.823136] ata2: SATA link down (SStatus 0 SControl 320)
  301. hotplug398add:9
  302. hotplug398add:[9/0/0]USB hub device:09h/xxh/xxh
  303. hotplug395add:[9/0/0]USB hub device:09h/xxh/xxh
  304. [ 3.953723] Core Release: 2.81a
  305. [ 3.956878] Setting default values for core params
  306. [ 4.161567] Using Buffer DMA mode
  307. [ 4.164901] Periodic Transfer Interrupt Enhancement - disabled
  308. [ 4.170749] Multiprocessor Interrupt Enhancement - disabled
  309. [ 4.176343] OTG VER PARAM: 0, OTG VER FLAG: 0
  310. [ 4.180741] dwc_otg dwc_otg.0: DWC OTG Controller
  311. [ 4.182944] usb 1-1: new high-speed USB device number 2 using xhci-hcd
  312. [ 4.192045] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 3
  313. [ 4.199140] dwc_otg dwc_otg.0: irq 53, io mem 0x00000000
  314. [ 4.204536] Init: Port Power? op_state=1
  315. [ 4.208468] Init: Power Port (0)
  316. [ 4.211756] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
  317. [ 4.218576] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  318. [ 4.225825] usb usb3: Product: DWC OTG Controller
  319. [ 4.228899] usb 1-1: New USB device found, idVendor=174c, idProduct=2074
  320. [ 4.228906] usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
  321. [ 4.228912] usb 1-1: Product: ASM107x
  322. [ 4.228917] usb 1-1: Manufacturer: Asmedia
  323. [ 4.228922] usb 1-1: SerialNumber: 0000000A0003
  324. [ 4.233711] hub 1-1:1.0: USB hub found
  325. [ 4.233967] hub 1-1:1.0: 4 ports detected
  326. [ 4.264542] usb usb3: Manufacturer: Linux 3.2.54 dwc_otg
  327. [ 4.264548] usb usb3: SerialNumber: dwc_otg.0
  328. hotplug403add:
  329. hotplug404add:9
  330. [ 4.284123] hub 3-0:1.0: USB hub found
  331. [ 4.288023] hub 3-0:1.0: 1 port detected
  332. hotplug404add:[9/0/1]USB hub device:09h/xxh/xxh
  333. hotplug405add:
  334. [ 4.319414] mousedev: PS/2 mouse device common for all mice
  335. hotplug406add:9
  336. [ 4.341721] c2k-rtc c2k-rtc: rtc core: registered c2k as rtc0
  337. [ 4.347534] C2000 RTC, (c) 2012 Mindspeed Technologies
  338. [ 4.352811] c2k-rtc c2k-rtc: Warning: Invalid RTC value so initializing it
  339. [ 4.362603] i2c /dev entries driver
  340. hotplug406add:[9[ 4.373877] comcerto_i2c_calculate_dividers: speed=97kHz, M=1, N=7, dividers=0x0f
  341. /0/0]USB hub device:09h/xxh/xxh
  342. [ 4.387782] i2c-core: driver [eeprom] using legacy suspend method
  343. [ 4.393934] i2c-core: driver [eeprom] using legacy resume method
  344. [ 4.400626] comcerto_wdt: support registered
  345. [ 4.409571] md: linear personality registered for level -1
  346. [ 4.415110] md: raid0 personality registered for level 0
  347. [ 4.420440] md: raid1 personality registered for level 1
  348. [ 4.423084] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
  349. [ 4.432329] md: raid10 personality registered for level 10
  350. [ 4.437836] md: raid6 personality registered for level 6
  351. [ 4.443167] md: raid5 personality registered for level 5
  352. [ 4.445363] usb 2-1: New USB device found, idVendor=174c, idProduct=3074
  353. [ 4.445370] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
  354. [ 4.445377] usb 2-1: Product: ASM107x
  355. [ 4.445381] usb 2-1: Manufacturer: Asmedia
  356. [ 4.445386] usb 2-1: SerialNumber: 0000000A0003
  357. [ 4.474671] md: raid4 personality registered for level 4
  358. [ 4.480978] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
  359. [ 4.495544] hub 2-1:1.0: USB hub found
  360. [ 4.500108] hub 2-1:1.0: 4 ports detected
  361. hotplug423add:
  362. hotplug425add:[9/0/0]USB hub device:09h/xxh/xxh
  363. [ 4.569382] usbcore: registered new interface driver usbhid
  364. [ 4.575016] usbhid: USB HID core driver
  365. [ 4.579609] etherip: Ethernet over IPv4 tunneling driver
  366. [ 4.584977] etherip ----- is functional
  367. [ 4.594933] TCP cubic registered
  368. [ 4.598573] NET: Registered protocol family 10
  369. [ 4.605383] IPv6 over IPv4 tunneling driver
  370. [ 4.627906] NET: Registered protocol family 17
  371. [ 4.632533] 8021q: 802.1Q VLAN Support v1.8
  372. [ 4.636794] Registering the dns_resolver key type
  373. [ 4.641532] Clocks: disabled unused uart
  374. [ 4.645487] Clocks: disabled unused gemtx
  375. [ 4.649508] Clocks: disabled unused ipsec_spacc
  376. [ 4.654066] Clocks: disabled unused dpi_cie
  377. [ 4.658259] Clocks: disabled unused dpi_decomp
  378. [ 4.662715] Clocks: disabled unused pcie1
  379. [ 4.666758] Clocks: disabled unused ext_phy0
  380. [ 4.671039] Clocks: disabled unused ext_phy1
  381. [ 4.675336] Clocks: disabled unused ext_phy2
  382. [ 4.679617] Clocks: disabled unused tpi
  383. [ 4.683479] Clocks: disabled unused csys
  384. [ 4.687410] Clocks: disabled unused tsuntg
  385. [ 4.691517] Clocks: disabled unused sata_occ
  386. [ 4.695807] Clocks: disabled unused pcie_occ
  387. [ 4.700088] Clocks: disabled unused sgmii_occ
  388. [ 4.715908] UBI: attaching mtd2 to ubi0
  389. [ 4.723066] UBI: scanning is finished
  390. [ 4.726743] UBI error: ubi_read_volume_table: the layout volume was not found
  391. [ 4.733926] UBI error: ubi_attach_mtd_dev: failed to attach mtd2, error -22
  392. [ 4.740922] UBI error: ubi_init: cannot attach mtd2
  393. [ 4.745921] c2k-rtc c2k-rtc: setting system clock to 2012-07-12 18:25:01 UTC (1342117501)
  394. [ 4.760376] Freeing init memory: 3128K
  395. *** Stage 1: Setup system and device drivers ***
  396. Fail to open gpio device
  397. [ 6.703746] pfe_module_init
  398. [ 6.706605] pfe_platform_probe
  399. [ 6.710856] ipsec: baseaddr :9a000000 --- c0a00000
  400. [ 6.716691] pfe_probe
  401. [ 6.718970] PFE Driver version:
  402. [ 6.718972] pfe_ctrl_12_00_2
  403. [ 6.718974] built with pfe sources version: pfe_12_00_2
  404. [ 6.730263] cbus_baseaddr: c3000000, ddr_baseaddr: c2000000, ddr_phys_baseaddr: 3400000, ddr_size: c00000
  405. [ 6.739874] pfe_hw_init
  406. [ 6.742327] CLASS version: 20
  407. [ 6.745313] TMU version: 1011231
  408. [ 6.748549] BMU1 version: 21
  409. [ 6.751435] BMU2 version: 21
  410. [ 6.754335] EMAC1 network cfg: 80000
  411. [ 6.757918] EMAC2 network cfg: 80000
  412. [ 6.761501] EMAC3 network cfg: 80000
  413. [ 6.765091] EGPI1 version: 50
  414. [ 6.768065] EGPI2 version: 50
  415. [ 6.771038] EGPI3 version: 50
  416. [ 6.774015] HGPI version: 50
  417. [ 6.776902] GPT version: 0
  418. [ 6.779614] HIF version: 10
  419. [ 6.782413] HIF NOPCY version: 10
  420. [ 6.785739] UTIL version: 20
  421. [ 6.788626] bmu_init(1) done
  422. [ 6.791514] bmu_init(2) done
  423. [ 6.801016] class_init() done
  424. [ 6.804003] tmu_init: mem init
  425. [ 6.807064] tmu_init: lmem init
  426. [ 6.810254] tmu_init() done
  427. [ 6.813057] util_init() done
  428. [ 6.815947] gpi_init(1) done
  429. [ 6.818835] gpi_init(2) done
  430. [ 6.821723] gpi_init(3) done
  431. [ 6.824616] gpi_init(hif) done
  432. [ 6.827675] bmu_enable(1) done
  433. [ 6.830736] bmu_enable(2) done
  434. [ 6.833804] pfe_hif_lib_init
  435. [ 6.836891] pfe_hif_init
  436. [ 6.839429] pfe_hif_alloc_descr
  437. [ 6.842781] pfe_hif_init_buffers
  438. [ 6.846165] pfe_firmware_init
  439. [ 6.867889] pfe_load_elf
  440. [ 6.870448] pe_load_ddr_section: load address(3fb0000) and elf file address(c083b000) rcvd
  441. [ 6.902477] PFE binary version: pfe_12_00_2
  442. [ 6.906705] pfe_firmware_init: class firmware loaded 0xb20 0xc3010000
  443. [ 6.913172] pfe_load_elf
  444. [ 6.917064] pfe_firmware_init: tmu firmware loaded 0x220
  445. [ 6.922389] pfe_load_elf
  446. [ 6.926835] pfe_firmware_init: util firmware loaded 0x16c0
  447. [ 6.932365] pfe_ctrl_init
  448. [ 6.954474] pfe_ctrl_init finished
  449. [ 6.957887] pfe_eth_init
  450. [ 6.961377] pfe_ctrl_timer
  451. [ 6.974034] Comcerto MDIO Bus: probed
  452. [ 7.066983] eth0: pfe_eth_init_one: created interface, baseaddr: c3200000
  453. [ 7.165112] eth1: pfe_eth_init_one: created interface, baseaddr: c3220000
  454. [ 7.171930] pfe_vwd_init
  455. [ 7.174671] pfe_vwd_init: created vwd device(250, 0)
  456. [ 7.179651] pfe_vwd_driver_init: start
  457. [ 7.183441] pfe_vwd_up: start
  458. [ 7.186471] comcerto_wifi_rx_fastpath_register:33 VWD Tx function registered
  459. [ 7.193567] pfe_vwd_driver_init: end
  460. [ 7.197151] pfe_pcap_init
  461. crw-rw---- 1 root root 10, 130 Jul 12 18:25 /dev/comcerto_wdt
  462. Starting watchdog ...
  463. -rw-r--r-- 1 root root 0 Jul [ 7.229197] MCU watchdog is reset!
  464. 12 18:25 /proc/mcu_wdt
  465. [ 7.708531] egiga0: pfe_eth_open
  466. [ 7.711995] hif_process_client_req: register client_id 0
  467. [ 7.717337] pfe_hif_client_register
  468. [ 7.720840] hif_lib_set_rx_cpu_affinity:Client (0) and HIF Rx processing will use same cpu
  469. [ 7.729144] egiga0: pfe_gemac_init
  470. [ 7.737333] egiga1: pfe_eth_open
  471. [ 7.740799] hif_process_client_req: register client_id 1
  472. [ 7.746142] pfe_hif_client_register
  473. [ 7.749647] hif_lib_set_rx_cpu_affinity:Client (1) and HIF Rx processing will use same cpu
  474. [ 7.758007] egiga1: pfe_gemac_init
  475. *** Stage 2: Prepare the root file system ***
  476. mknod: /dev/gpio: File exists
  477. Initialize fan control
  478. Wrote to 0x90470058: 0x05000000
  479. Wrote to 0x90458000: 0x80000001
  480. Wrote to 0x90458028: 0x80001388
  481. Mount system partition...
  482. crw-rw---- 1 root root 10, 58 Jul 12 2012 /dev/ubi_ctrl
  483.  
  484. [ 8.376019] UBI: attaching mtd7 to ubi7
  485. [ 9.103726] UBI: scanning is finished
  486. [ 9.119521] UBI: attached mtd7 (name "rootfs2", size 110 MiB) to ubi7
  487. [ 9.126005] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  488. [ 9.132813] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  489. [ 9.139554] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
  490. [ 9.146454] UBI: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0
  491. [ 9.152389] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
  492. [ 9.159552] UBI: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 1035530652
  493. [ 9.168628] UBI: available PEBs: 10, total reserved PEBs: 870, PEBs reserved for bad PEB handling: 40
  494. [ 9.177902] UBI: background thread "ubi_bgt7d" started, PID 857
  495. UBI device number 7, total 880 LEBs (111738880 bytes, 106.6 MiB), available 10 LEBs (1269760 bytes, 1.2 MiB), LEB size 126976 bytes (124.0 KiB)
  496. [ 9.318533] UBIFS: mounted UBI device 7, volume 0, name "ubi_rootfs2"
  497. [ 9.325008] UBIFS: mounted read-only
  498. [ 9.328594] UBIFS: file system size: 103612416 bytes (101184 KiB, 98 MiB, 816 LEBs)
  499. [ 9.336452] UBIFS: journal size: 5206016 bytes (5084 KiB, 4 MiB, 41 LEBs)
  500. [ 9.343787] UBIFS: media format: w4/r0 (latest is w4/r0)
  501. [ 9.349635] UBIFS: default compressor: lzo
  502. [ 9.353746] UBIFS: reserved for root: 4893869 bytes (4779 KiB)
  503. ls: /sys/block/sd?: No such file or directory
  504. /bin/storage_asm_mntfw_swap.sh: line 366: can't open /tmp/intern_disk.list: no such file
  505. can not found fw raid uuid
  506. can not found swap raid uuid
  507. /bin/storage_asm_mntfw_swap.sh: line 376: can't open /tmp/intern_disk.list: no such file
  508. /sbin/mdadm --grow /dev/md0 --raid-devices=4 --force
  509. mdadm: /dev/md0 is not an active md array - aborting
  510. /sbin/mdadm --grow /dev/md1 --raid-devices=4 --force
  511. mdadm: /dev/md1 is not an active md array - aborting
  512. storage_asm_mntfw_swap.sh can not swap on /dev/md1
  513. 1
  514. WARNING: No valid partition on HDD or no HDD plugged!
  515. WARNING: No valid partition on HDD or no HDD plugged
  516. Boot from RAM disk
  517. [ 11.723147] PHY: comcerto-0:04 - Link is Up - 1000/Full
  518. [ 11.728419] pfe_eth_adjust_link: PHY: comcerto-0:04, phy->link: 1
  519. Erasing 64 Kibyte @ 30000 -- 100 % complete
  520. Mount system disk image ...
  521. [ 31.340278] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
  522. [ 31.348538] EXT4-fs (loop0): mounted filesystem without journal. Opts: (null)
  523. mount: mount point /usr/local/var does not exist
  524. [ 31.476937] UBI: attaching mtd3 to ubi3
  525. [ 31.547105] UBI: scanning is finished
  526. [ 31.566217] UBI: attached mtd3 (name "config", size 10 MiB) to ubi3
  527. [ 31.572507] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  528. [ 31.579337] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  529. [ 31.586065] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
  530. [ 31.592964] UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0
  531. [ 31.598813] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
  532. [ 31.605976] UBI: max/mean erase counter: 1196/560, WL threshold: 4096, image sequence number: 2133983814
  533. [ 31.615487] UBI: available PEBs: 0, total reserved PEBs: 80, PEBs reserved for bad PEB handling: 40
  534. [ 31.624575] UBI: background thread "ubi_bgt3d" started, PID 974
  535. UBI device number 3, total 80 LEBs (10158080 bytes, 9.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
  536. [ 31.781574] UBIFS: mounted UBI device 3, volume 0, name "ubi_config"
  537. [ 31.787966] UBIFS: file system size: 3428352 bytes (3348 KiB, 3 MiB, 27 LEBs)
  538. [ 31.795304] UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
  539. [ 31.802459] UBIFS: media format: w4/r0 (latest is w4/r0)
  540. [ 31.808312] UBIFS: default compressor: lzo
  541. [ 31.812419] UBIFS: reserved for root: 161928 bytes (158 KiB)
  542. mount /etc/zyxel successfully and /etc/zyxel/conf exist, nothing special.
  543. Start rcS2 of ZyXEL style
  544. *** Stage 3: Start services on HDD ***
  545. [ 32.024398] NTFS driver 2.1.30 [Flags: R/O MODULE].
  546. [ 32.039896] tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
  547. [ 32.049546] Disabling lock debugging due to kernel taint
  548. [ 32.062770] Tuxera NTFS driver 3014.4.29 [Flags: R/W MODULE].
  549. [ 32.081204] PPP generic driver version 2.4.2
  550. [ 32.106158] PPP MPPE Compression module registered
  551. [ 32.128775] PPP Deflate Compression module registered
  552. [ 32.142470] NET: Registered protocol family 24
  553. [ 32.159494] PPP BSD Compression module registered
  554. [ 32.477307] elp_register_ocf: Comcerto 2000 ELP Crypto Offload Engine
  555. [ 32.483743] m86xxx_elp: Registering key des/3des aes md5 sha1 sha2_256 sha2_384 sha2_512 sha256_hmac null
  556. Press ENTER to continue...
  557. Starting zylogd...
  558. zylog starts.
  559. Starting uamd...
  560. Starting WSGI server...
  561. CherryPy Checker:
  562. The Application mounted at '' has an empty config.
  563.  
  564. killall: pure-ftpd: no process killed
  565.  
  566. Usage:
  567. umount [-hV]
  568. umount -a [options]
  569. umount [options] <source> | <directory>
  570.  
  571. Options:
  572. -a, --all unmount all filesystems
  573. -A, --all-targets unmount all mountpoints for the given device in the
  574. current namespace
  575. -c, --no-canonicalize don't canonicalize paths
  576. -d, --detach-loop if mounted loop device, also free this loop device
  577. --fake dry run; skip the umount(2) syscall
  578. -f, --force force unmount (in case of an unreachable NFS system)
  579. -i, --internal-only don't call the umount.<type> helpers
  580. -n, --no-mtab don't write to /etc/mtab
  581. -l, --lazy detach the filesystem now, clean up things later
  582. -O, --test-opts <list> limit the set of filesystems (use with -a)
  583. -R, --recursive recursively unmount a target with all its children
  584. -r, --read-only in case unmounting fails, try to remount read-only
  585. -t, --types <list> limit the set of filesystem types
  586. -v, --verbose say what is being done
  587.  
  588. -h, --help display this help and exit
  589. -V, --version output version information and exit
  590.  
  591. For more details see umount(8).
  592.  
  593. Usage:
  594. umount [-hV]
  595. umount -a [options]
  596. umount [options] <source> | <directory>
  597.  
  598. Options:
  599. -a, --all unmount all filesystems
  600. -V, --version output version information and exit
  601.  
  602. For more details see umount(8).
  603. BusyBox v1.19.4 (2018-05-22 01:23:15 CST) multi-call binary.
  604.  
  605. Usage: rmdir [OPTIONS] DIRECTORY...
  606.  
  607. [22/Apr/2022:09:52:32] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable
  608. [22/Apr/2022:09:52:34] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable
  609. [22/Apr/2022:09:52:34] [network_main_model_back.py.pre](ipv6_dhcp_static_setting_apply)(229): The interface bond0 is down!
  610. [22/Apr/2022:09:52:37] [network_main_model_back.py.pre](ipv6_dhcp_static_setting_apply)(229): The interface egiga1 is down!
  611. [22/Apr/2022:09:52:43] [network_main_model_front.py.pre](apache_config_setting)(627): There is no statement '#WebService Start#' in httpd_zld.conf. keep going...
  612.  
  613. Usage:
  614. umount [-hV]
  615. umount -a [options]
  616. umount [options] <source> | <directory>
  617.  
  618. Options:
  619. -a, --all unmount all filesystems
  620. -V, --version output version information and exit
  621.  
  622. For more details see umount(8).
  623. no printer device detected.
  624.  
  625. Usage:
  626. umount [-hV]
  627. umount -a [options]
  628. umount [options] <source> | <directory>
  629.  
  630. Options:
  631. -a, --all unmount all filesystems
  632. -V, --version output version information and exit
  633.  
  634. For more details see umount(8).
  635. BusyBox v1.19.4 (2018-05-22 01:23:15 CST) multi-call binary.
  636.  
  637. Usage: rmdir [OPTIONS] DIRECTORY...
  638.  
  639. No more ZySH daemon and client...
  640. cat: can't open '/var/run/syslog-ng.pid': No such file or directory
  641. Try to KILL SIGHUP to syslog-ng: pid=0
  642. syslog-ng not running, start /usr/sbin/syslog-ng
  643. server'1' has been reset
  644. Apr 22 10:52:48 NAS540 syslog-ng[1641]: syslog-ng starting up; version='2.0.10'
  645. argv[0]=/usr/sbin/zylog_config
  646. argv[1]=mail
  647. argv[2]=1
  648. argv[3]=subject
  649. argv[4]=NAS540 Log Report
  650. mail server'1' subject:NAS540 Log Report
  651. argv[0]=/usr/sbin/zylog_config
  652. argv[1]=mail
  653. argv[2]=1
  654. argv[3]=category
  655. argv[4]=all
  656. argv[5]=level
  657. argv[6]=alert
  658. mail server '1' log_category(all) is:alert
  659. argv[0]=/usr/sbin/zylog_config
  660. argv[1]=mail
  661. argv[2]=1
  662. argv[3]=category
  663. argv[4]=all
  664. argv[5]=level
  665. argv[6]=all
  666. mail server '1' log_category(all) is:all
  667. argv[0]=/usr/sbin/zylog_config
  668. argv[1]=mail
  669. argv[2]=1
  670. argv[3]=schedule
  671. argv[4]=hourly
  672. mail server '1' schedule is : hourly
  673. Starting "/etc/init.d/zypkg_controller.sh".
  674. Starting to set up zy-pkgs environment ...
  675. -> No volume exists now. zy-pkgs will not work.
  676. Starting smbd...
  677. Starting nmbd...
  678. Apr 22 10:52:52 NAS540 smbd[1728]: [2022/04/22 10:52:52.038509, 0] ../source3/printing/print_standard.c:68(std_pcap_cache_reload)
  679. Apr 22 10:52:52 NAS540 smbd[1728]: Unable to open printcap file /etc/printcap for read!
  680. Starting NSU Agent...
  681. Starting AFP... avahi-daemonApr 22 10:52:52 NAS540 avahi-daemon[1788]: avahi-daemon 0.6.31 starting up.
  682. Apr 22 10:52:52 NAS540 avahi-daemon[1788]: WARNING: No NSS support for mDNS detected, consider installing nss-mdns!
  683. Apr 22 10:52:52 NAS540 avahi-daemon[1788]: Loading service file /etc/avahi/services/afp.service.
  684. Apr 22 10:52:52 NAS540 avahi-daemon[1788]: Loading service file /etc/avahi/services/web.service.
  685. Apr 22 10:52:52 NAS540 avahi-daemon[1788]: Joining mDNS multicast group on interface egiga0.IPv4 with address 192.168.178.34.
  686. Apr 22 10:52:52 NAS540 avahi-daemon[1788]: New relevant interface egiga0.IPv4 for mDNS.
  687. Apr 22 10:52:52 NAS540 avahi-daemon[1788]: Network interface enumeration completed.
  688. Apr 22 10:52:52 NAS540 avahi-daemon[1788]: Registering new address record for 192.168.178.34 on egiga0.IPv4.
  689. Apr 22 10:52:52 NAS540 avahi-daemon[1788]: Registering HINFO record with values 'ARMV7L'/'LINUX'.
  690. netatalk.
  691. There is no usable system volume! Do nothing...
  692. Apr 22 10:52:52 NAS540 netatalk[1797]: Netatalk AFP server starting
  693. Apr 22 10:52:52 NAS540 netatalk[1797]: Registered with Zeroconf
  694. GMT offset=3600s
  695. setting system time zone to tz_minuteswest=-60
  696. killall: hd-idle: no process killed
  697. ===> Starting schedule_controller ...
  698. Apr 22 10:52:53 NAS540 avahi-daemon[1788]: Server startup complete. Host name is NAS540.local. Local service cookie is 3332038921.
  699. Apr 22 10:52:53 NAS540 cnid_metad[1814]: CNID Server listening on localhost:4700
  700. setLED COPY OFF
  701. Apr 22 10:52:54 NAS540 avahi-daemon[1788]: Service "NAS540" (/etc/avahi/services/web.service) successfully established.
  702. Apr 22 10:52:54 NAS540 avahi-daemon[1788]: Service "NAS540 (AFP)" (/etc/avahi/services/afp.service) successfully established.
  703. led_state_map_addr = 500
  704. /etc/init.d/schedule_trigger.sh: line 87: can't create /i-data/.system/sch_debug.log: nonexistent directory
  705. killall: timer_source: no process killed
  706. OK
  707. Apr 22 10:52:59 NAS540 afpd[1812]: Netatalk AFP/TCP listening on 192.168.178.34:548
  708. Starting app_wd...
  709. Power on HD1 ...
  710. Power on HD2 ...
  711. Power on HD3 ...
  712. Power on HD4 ...
  713. Update zypkg list
  714. ===> Generate zysync server config ...
  715. ===> Generating volume list ...
  716. ===> Generating zysync config file ...
  717. rm: can't remove '/tmp/zysync_modules': No such file or directory
  718. ===> Starting zysync server ...
  719. [INFO]: Starting server mode ...
  720.  
  721. Apr 22 10:53:01 NAS540 rsyncd[2518]: rsync: failed to open log-file /i-data/.system/zysyncd.log: No such file or directory (2)
  722. Apr 22 10:53:01 NAS540 rsyncd[2518]: Ignoring "log file" setting.
  723. Apr 22 10:53:01 NAS540 rsyncd[2518]: zysync server v2.00 starting, listening on port 873.
  724. Done
  725. ===> Generating stunnel server config file ...
  726. ===> Starting stunnel server ...
  727. [.] stunnel 5.02 on arm-unknown-linux-gnu platform
  728. [.] Compiled/running with OpenSSL 1.0.2h 3 May 2016
  729. [.] Threading:FORK Sockets:POLL,IPv6 SSL:FIPS
  730. [ ] errno: (*__errno_location ())
  731. [.] Reading configuration from file /etc/stunneld.conf
  732. [.] FIPS mode disabled
  733. [ ] Compression disabled
  734. [ ] PRNG seeded successfully
  735. [ ] Initializing service [szysync]
  736. [ ] Loading cert from file: /etc/zyxel/BackupPlanner/zysync/zysync.cert
  737. [ ] Loading key from file: /etc/zyxel/BackupPlanner/zysync/zysync.key
  738. [:] Insecure file permissions on /etc/zyxel/BackupPlanner/zysync/zysync.key
  739. [ ] Private key check succeeded
  740. [ ] DH initialization
  741. [ ] Could not load DH parameters from /etc/zyxel/BackupPlanner/zysync/zysync.cert
  742. [ ] Using hardcoded DH parameters
  743. [ ] DH initialized with 2048-bit key
  744. [ ] ECDH initialization
  745. [ ] ECDH initialized with curve prime256v1
  746. [ ] SSL options set: 0x01000004
  747. [.] Configuration successful
  748. [ ] Service [szysync] (FD=7) bound to 0.0.0.0:9527
  749. [!] Cannot open log file: /i-data/.system/stunneld.log
  750. [ ] Closing service [szysync]
  751. [ ] Service [szysync] closed (FD=7)
  752. [ ] Sessions cached before flush: 0
  753. [ ] Sessions cached after flush: 0
  754. [ ] Service [szysync] closed
  755. Done
  756. [ ok ] The Linux SCSI Target is already stopped
  757. [warn] Creating missing directory /var/target/pr ... (warning).
  758. [warn] Creating missing directory /var/target/alua ... (warning).
  759. [info] The Linux SCSI Target looks properly installed.
  760. [warn] The configfs filesystem was not mounted, consider adding it to fstab ... (warning).
  761. [info] Loaded core module target_core_file.
  762. [warn] Core module target_core_mod already loaded ... (warning).
  763. [info] Loaded fabric module iscsi_target_mod.
  764. [warn] Startup config /etc/target/scsi_target.lio is empty, skipping ... (warning).
  765. [ ok ] Started The Linux SCSI Target
  766. 2022/04/22 10:53:04 [ipnotify] : execute ipnotify STARTUP
  767. [ipnotify_exec.sh]: ******** run ipnotify_exec.sh STARTUP********
  768. [22/Apr/2022:10:53:05] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable
  769. [22/Apr/2022:10:53:05] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable
  770. [22/Apr/2022:10:53:06] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable
  771. [22/Apr/2022:10:53:06] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable
  772. 2022/04/22 10:53:06 [ipnotify] : rth->rta_type = 1, IFA_ADDRESS=1, IFA_LOCAL=2
  773. 2022/04/22 10:53:06 [ipnotify] : detect a delete IP and execute /sbin/ipnotify_exec.sh
  774. [ipnotify_exec.sh]: ******** detect egiga1 delete IP********
  775. loop link has been checked. Do nothing
  776. Apr 22 10:53:07 NAS540 ifplugd(egiga0): started: BusyBox v1.19.4 (2018-05-22 01:23:15 CST)
  777. Apr 22 10:53:07 NAS540 ifplugd(egiga0): using SIOCETHTOOL detection mode
  778. Apr 22 10:53:07 NAS540 ifplugd(egiga0): link is up
  779. Apr 22 10:53:07 NAS540 ifplugd(egiga1): started: BusyBox v1.19.4 (2018-05-22 01:23:15 CST)
  780. Apr 22 10:53:07 NAS540 ifplugd(egiga1): using SIOCETHTOOL detection mode
  781. Apr 22 10:53:07 NAS540 ifplugd(egiga1): link is down
  782. [22/Apr/2022:10:53:08] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable
  783. [22/Apr/2022:10:53:08] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable
  784. ===> Stopping crond ...
  785. Apr 22 10:53:10 NAS540 httpd[2755]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
  786. Apr 22 10:53:10 NAS540 httpd[2755]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
  787. Apr 22 10:53:10 NAS540 httpd[2755]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
  788. Apr 22 10:53:10 NAS540 httpd[2755]: [error] mod_auth_zyxel: initialized.
  789. ===> Starting crond ...
  790. core_checksum : 1a800bf182490ffdbc8b5522a719505c
  791. fwversion : V5.21(AATB.3)
  792. img_checksum : 3ff199e80aacc1d3133b873e0b039089
  793. modelid : B103
  794. revision : 51166
  795. romfile_checksum : 1473
  796. zld_checksum : 29881163cdc438bd103b98d7b0a97318
  797. Apr 22 10:53:11 NAS540 httpd[2764]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
  798. Apr 22 10:53:11 NAS540 httpd[2764]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
  799. Apr 22 10:53:11 NAS540 httpd[2764]: [error] mod_auth_zyxel: initialized.
  800. check time zone and modify time zone
  801. [ 79.702131] bz time = 1
  802. [ 79.704607] bz status = 1
  803. [ 79.707233] bz_timer_status = 0
  804. [ 79.710381] start buzzer
  805. led_state_map_addr = 406
  806.  
  807. Please press Enter to activate this console. ipc_send:54: send IPC event OK
  808. ipc_send:54: send IPC event OK
  809. ipc_send:54: send IPC event OK
  810. ipc_send:54: send IPC event OK
  811. Apr 22 10:54:18 NAS540 ntpdate[2843]: no server suitable for synchronization found
  812. Apr 22 11:04:53 NAS540 smbd[1728]: [2022/04/22 11:04:53.237170, 0] ../source3/printing/print_standard.c:68(std_pcap_cache_reload)
  813. Apr 22 11:04:53 NAS540 smbd[1728]: Unable to open printcap file /etc/printcap for read!
  814. Apr 22 10:08:16 NAS540 linuxrc: starting pid 4134, tty '': '/etc/init.d/rc.shutdown'
  815. led_state_map_addr = 40e
  816. Starting "/etc/init.d/zypkg_controller.sh".
  817. Stopping all zypkgs via "/etc/init.d/zypkg_controller.sh" ...
  818. - Failed: dependency file "/i-data/.system/zy-pkgs/ZYPKG_DEPS" not exists.
  819. Starting "/etc/init.d/zypkg_controller.sh".
  820. Starting to release zy-pkgs environment ...
  821. umount: /usr/local/apache/htdocs/desktop,/pkg/: not mounted
  822. Finish "/etc/init.d/zypkg_controller.sh".
  823. Apr 22 11:08:17 NAS540 smbd[1728]: [2022/04/22 11:08:17.798189, 0] ../lib/util/pidfile.c:153(pidfile_unlink)
  824. Apr 22 11:08:17 NAS540 smbd[1728]: Failed to delete pidfile /var/run/smbd.pid. Error was No such file or directory
  825. start kill.
  826. 756 root 2512 S < /sbin/watchdog -t 8 -T 15 /dev/comcerto_wdt
  827. 1218 root 3696 S /usr/sbin/zylogd
  828. 1228 root 6000 S /usr/sbin/uamd
  829. 1265 root 123m S python /usr/local/apache/web_framework/main_wsgi.pyc
  830. 1509 root 2644 S /sbin/telnetd
  831. 1512 root 5484 S /sbin/sshd -f /etc/ssh/sshd_config
  832. 1641 root 3148 R /usr/sbin/syslog-ng
  833. 1681 root 23232 R N pure-ftpd (SERVER)
  834. 1728 root 25944 R N /usr/sbin/smbd -D
  835. 1732 root 20336 S < /usr/sbin/nsuagent
  836. 179
  837.  
  838. [info] Cleared configuration.
  839. [info] Unloaded iscsi_target_mod fabric module.
  840. [info] Unloaded target_core_file target core module.
  841. [info] Unloaded target_core_mod target core module.
  842. [ ok ] Stopped The Linux SCSI Target
  843. BusyBox v1.19.4 (2018-05-22 01:23:15 CST) multi-call binary.
  844.  
  845. Usage: swapoff [-a] [DEVICE]
  846.  
  847. [ 997.994067] UBIFS: un-mount UBI device 3, volume 0
  848. rootfs / rootfs rw 0 0
  849. /proc /proc proc rw,relatime 0 0
  850. /sys /sys sysfs rw,relatime 0 0
  851. none /proc/bus/usb usbfs rw,relatime 0 0
  852. devpts /dev/pts devpts rw,relatime,mode=600 0 0
  853. ubi7:ubi_rootfs2 /firmware/mnt/nand ubifs ro,relatime 0 0
  854. none /firmware/mnt/sysdisk ramfs ro,relatime 0 0
  855. /dev/loop0 /ram_bin ext2 ro,relatime,user_xattr,barrier=1 0 0
  856. /dev/loop0 /usr ext2 ro,relatime,user_xattr,barrier=1 0 0
  857. /de[ 998.077864] UBIFS: un-mount UBI device 7, volume 0
  858. v/loop0 /lib/security ext2 ro,relatime,user_xattr,barrier=1 0 0
  859. /dev/loop0 /lib/modules ext2 ro,relatime,user_xattr,barrier=1 0 0
  860. /dev/loop0 /lib/locale ext2 ro,relatime,user_xattr,barrier=1 0 0
  861. /dev/ram0 /tmp/tmpfs tmpfs rw,relatime,size=5120k 0 0
  862. /dev/ram0 /usr/local/etc tmpfs rw,relatime,size=5120k 0 0
  863. configfs /sys/kernel/config configfs rw,relatime 0 0
  864. [ 998.137842] UBI: detaching mtd3 from ubi3
  865. [ 998.148550] UBI: mtd3 is detached from ubi3
  866. ubidetach: error!: cannot detach mtd5
  867. error 19 (No such device)
  868. [ 998.168135] UBI: detaching mtd7 from ubi7
  869. [ 998.180817] UBI: mtd7 is detached from ubi7
  870. Settings for egiga0:
  871. Supported ports: [ TP MII ]
  872. Supported link modes: 10baseT/Half 10baseT/Full
  873. 100baseT/Half 100baseT/Full
  874. 1000baseT/Half 1000baseT/Full
  875. Supported pause frame use: Symmetric Receive-only
  876. Supports auto-negotiation: Yes
  877. Advertised link modes: 10baseT/Half
  878. Advertised pause frame use: Symmetric Receive-only
  879. Advertised auto-nego[ 998.233022] PHY: comcerto-0:04 - Link is Up - 10/Half
  880. [ 998.238418] pfe_eth_adjust_link: PHY: comcerto-0:04, phy->link: 1
  881. tiation: No
  882. Speed: 10Mb/s
  883. Duplex: Half
  884. Port: MII
  885. PHYAD: 4
  886. Transceiver: external
  887. Auto-negotiation: off
  888. Current message level: 0x00000036 (54)
  889. probe link ifdown ifup
  890. Link detected: yes
  891. Settings for egiga1:
  892. Supported ports: [ TP MII ]
  893. Supported link modes: 10baseT/Half 10baseT/Full
  894. 100baseT/Half 100baseT/Full
  895. 1000baseT/Half 1000baseT/Full
  896. Supported pause frame use: Symmetric Receive-only
  897. Supports auto-negotiation: Yes
  898. Advertised link modes: 10baseT/Half
  899. Advertised pause frame use: Symmetric Receive-only
  900. Advertised auto-negotiation: No
  901. Speed: 10Mb/s
  902. Duplex: Half
  903. Port: MII
  904. PHYAD: 6
  905. Transceiver: external
  906. Auto-negotiation: off
  907. Current message level: 0x00000036 (54)
  908. probe link ifdown ifup
  909. Link detected: no
  910. The system is going down NOW!
  911. Sent SIGTERM to all processes
  912. Sent SIGKILL to all processes
  913. Requesting system poweroff
  914. [ 1000.243041] PHY: comcerto-0:04 - Link is Down
  915. [ 1000.247425] pfe_eth_adjust_link: PHY: comcerto-0:04, phy->link: 0
  916. [ 1001.202703] Power down.
  917. [ 1001.205181] GPIO[15] is pull high for power off
  918. ---> GPIO[20] is pull high for power off
  919. [ 1001.215834] Unhandled fault: external abort on non-linefetch (0x818) at 0x2ab73130
  920. Bus error
  921. [ 1004.336062] usb 1-1: USB disconnect, device number 2
  922.  
Add Comment
Please, Sign In to add comment
Public Pastes
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!