Slic3er 1.41.0 configuration - Anet AM8

# generated by Slic3r Prusa Edition 1.41.0-beta+win64 on 2018-08-09 at 20:22:20
avoid_crossing_perimeters = 0
bed_shape = 0x0,220x0,220x220,0x220
bed_temperature = 70
before_layer_gcode =
between_objects_gcode =
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_angle = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 2
clip_multipart_objects = 0
complete_objects = 0
cooling = 0
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_acceleration = 0
default_filament_profile =
default_print_profile =
deretract_speed = 0
disable_fan_first_layers = 3
dont_support_bridges = 1
duplicate_distance = 6
elefant_foot_compensation = 0
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = ;\n; Custom end G-Code\n;\nG91 ;relative positioning\n;G1 E-1 F300  ;retract the filament a bit \nG1 Z+10 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more\nG90 ;absolute positioning\nG1 X0 Y200 F2000 ; prepare for part removal\nM104 S0 ; turn off extruder\nM140 S0 ; turn off bed\nM84 ; disable motors\nM107 ; Luefter aus
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_loading_move = -2
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #F71E33
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 0.97
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFF80
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 5
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_settings_id = "Extrudr PETG"
filament_soluble = 0
filament_toolchange_delay = 0
filament_type = PET
filament_unload_time = 0
filament_unloading_speed = 90
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 75
first_layer_extrusion_width = 0
first_layer_height = 100%
first_layer_speed = 20
first_layer_temperature = 225
gap_fill_speed = 10
gcode_comments = 0
gcode_flavor = marlin
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 30%
infill_speed = 0
interface_shells = 0
layer_gcode =
layer_height = 0.2
machine_max_acceleration_e = 10000,5000
machine_max_acceleration_extruding = 1500,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 9000,1000
machine_max_acceleration_y = 9000,1000
machine_max_acceleration_z = 500,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 500,200
machine_max_feedrate_y = 500,200
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.2,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_fan_speed = 100
max_layer_height = 0.2
max_print_height = 200
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_fan_speed = 35
min_layer_height = 0.1
min_print_speed = 10
min_skirt_length = 5
notes =
nozzle_diameter = 0.4
octoprint_apikey = 82DE1ECD49F14A0492F798224851FB65
octoprint_cafile =
octoprint_host = 192.168.1.251
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
parking_pos_retraction = 92
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 50
perimeters = 3
post_process =
print_settings_id = AM8 Test
printer_model =
printer_notes =
printer_settings_id = AM8
printer_variant =
printer_vendor =
raft_layers = 0
remaining_times = 0
resolution = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 1.4
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 75
seam_position = aligned
serial_port =
serial_speed = 250000
silent_mode = 1
single_extruder_multi_material = 0
single_extruder_multi_material_priming = 1
skirt_distance = 10
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 5
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 30
spiral_vase = 0
standby_temperature_delta = -5
start_filament_gcode = "; Filament gcode\n"
start_gcode = ;\n; Custom start G-Code\n;\nG90 ; use absolute positioning\nM82 ; absolute extrusion mode\n\nM190 S[first_layer_bed_temperature]; warm up the bed and wait for it\nM104 S140; Pre-Heat nozzle but don't wait\nG4 S30; wait 30s\n\nG28; Home axis\nM420 L0 S1; Load bed mesh\n\n; Go to 0,0 to let the nozzle ooze into the air :P \nG1 X0 Y0 F1200;\nG1 Z0;\n\nM109 S[first_layer_temperature_0]; Heat nozzle\nM900 K0.12; Linear Advance\n\n; Prime the nozzle\nG1 X2 Y2 Z0.15 F1200\nG92 E0\nG1 X180 E20 F600\nG1 X200 F2000\nG92 E0\nG1 Z1 F6000\n\n\n; Begin of slicers code\n;
support_material = 1
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0.4
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 0.8
temperature = 225
thin_walls = 1
threads = 4
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 30
top_solid_layers = 4
travel_speed = 120
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
wipe_into_infill = 0
wipe_into_objects = 0
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
wiping_volumes_extruders = 70,70
wiping_volumes_matrix = 0
xy_size_compensation = 0
z_offset = 0