API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Jan 20th, 2020
97
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 11.67 KB | None | 0 0
raw download clone embed print report
  1. [ 0.000000] Linux version 4.9.198 (lipton@amd-a10) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7897-9d401013fc) ) #0 Tue Nov 5 14:12:18 2019
  2. [ 0.000000] bootconsole [early0] enabled
  3. [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
  4. [ 0.000000] SoC: Atheros AR9344 rev 3
  5. [ 0.000000] Determined physical RAM map:
  6. [ 0.000000] memory: 08000000 @ 00000000 (usable)
  7. [ 0.000000] User-defined physical RAM map:
  8. [ 0.000000] memory: 08000000 @ 00000000 (usable)
  9. [ 0.000000] Initrd not found or empty - disabling initrd
  10. [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  11. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  12. [ 0.000000] Zone ranges:
  13. [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
  14. [ 0.000000] Movable zone start for each node
  15. [ 0.000000] Early memory node ranges
  16. [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
  17. [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
  18. [ 0.000000] On node 0 totalpages: 32768
  19. [ 0.000000] free_area_init_node: node 0, pgdat 804b4104, node_mem_map 81000020
  20. [ 0.000000] Normal zone: 256 pages used for memmap
  21. [ 0.000000] Normal zone: 0 pages reserved
  22. [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
  23. [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
  24. [ 0.000000] pcpu-alloc: [0] 0
  25. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
  26. [ 0.000000] Kernel command line: benand_no_swecc=2 parts=1 boot_part_size=4194304 gpio=130603 HZ=250000000 mem=128M kmac=74:4D:28:C0:A0:73 board=951HnD board=951HnD board_rev=r2 ver=6.43.13 bver=6.43.2 hw_opt=00290005 boot=1 mlc=11 rootfstype=squashfs noinitrd
  27. [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  28. [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  29. [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  30. [ 0.000000] Writing ErrCtl register=00000000
  31. [ 0.000000] Readback ErrCtl register=00000000
  32. [ 0.000000] Memory: 124628K/131072K available (3467K kernel code, 153K rwdata, 816K rodata, 228K init, 203K bss, 6444K reserved, 0K cma-reserved)
  33. [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  34. [ 0.000000] NR_IRQS:51
  35. [ 0.000000] Clocks: CPU:500.000MHz, DDR:400.000MHz, AHB:400.000MHz, Ref:25.000MHz
  36. [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
  37. [ 0.000012] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
  38. [ 0.008863] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232)
  39. [ 0.081906] pid_max: default: 32768 minimum: 301
  40. [ 0.087262] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  41. [ 0.094781] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  42. [ 0.106053] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
  43. [ 0.117256] futex hash table entries: 256 (order: -1, 3072 bytes)
  44. [ 0.124806] NET: Registered protocol family 16
  45. [ 0.131805] MIPS: machine is MikroTik RouterBOARD 951Ui-2HnD
  46. [ 0.140491] rb: debug: id = 26
  47. [ 0.144049] rb: debug: id = 4
  48. [ 0.147508] rb: debug: id = 14
  49. [ 0.151076] rb: debug: id = 10
  50. [ 0.154631] rb: debug: id = 13
  51. [ 0.158188] rb: debug: id = 19
  52. [ 0.161755] rb: debug: id = 18
  53. [ 0.165311] rb: debug: id = 20
  54. [ 0.168868] rb: debug: id = 21
  55. [ 0.172436] rb: debug: id = 27
  56. [ 0.175991] rb: debug: id = 11
  57. [ 0.179548] rb: debug: id = 5
  58. [ 0.183018] rb: debug: id = 26
  59. [ 0.186573] rb: debug: id = 4
  60. [ 0.190031] rb: debug: id = 14
  61. [ 0.193599] rb: debug: id = 10
  62. [ 0.197155] rb: debug: id = 13
  63. [ 0.200712] rb: debug: id = 19
  64. [ 0.204279] rb: debug: id = 18
  65. [ 0.207835] rb: debug: id = 20
  66. [ 0.211392] rb: debug: id = 21
  67. [ 0.695573] rb: debug: id = 26
  68. [ 0.699140] rb: debug: id = 4
  69. [ 0.702597] rb: debug: id = 14
  70. [ 0.706184] rb: debug: id = 10
  71. [ 0.709738] rb: debug: id = 13
  72. [ 0.713296] rb: debug: id = 19
  73. [ 0.716864] rb: debug: id = 18
  74. [ 0.720419] rb: debug: id = 20
  75. [ 0.723976] rb: debug: id = 21
  76. [ 0.727543] rb: debug: id = 27
  77. [ 0.731099] rb: debug: id = 11
  78. [ 0.734656] rb: debug: id = 5
  79. [ 0.738125] rb: debug: id = 33
  80. [ 0.741681] rb: debug: id = 6
  81. [ 0.745139] rb: debug: id = 25
  82. [ 0.748707] rb: debug: id = 3
  83. [ 0.752164] rb: debug: id = 1
  84. [ 0.755622] rb: debug: id = 23
  85. [ 0.759190] rb: debug: id = 8
  86. [ 0.762647] rb: debug: id = 28
  87. [ 0.766204] rb: debug: id = 22
  88. [ 0.769782] rb: debug: id 0
  89. [ 0.772946] rb95x: debug: no art buf
  90. [ 0.798124] clocksource: Switched to clocksource MIPS
  91. [ 0.805112] NET: Registered protocol family 2
  92. [ 0.811007] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  93. [ 0.818984] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  94. [ 0.826208] TCP: Hash tables configured (established 1024 bind 1024)
  95. [ 0.833535] UDP hash table entries: 256 (order: 0, 4096 bytes)
  96. [ 0.840219] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  97. [ 0.847585] NET: Registered protocol family 1
  98. [ 0.852604] PCI: CLS 0 bytes, default 32
  99. [ 0.857501] Crashlog allocated RAM at address 0x3f00000
  100. [ 0.864743] workingset: timestamp_bits=30 max_order=15 bucket_order=0
  101. [ 0.879990] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  102. [ 0.886612] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  103. [ 0.907924] io scheduler noop registered
  104. [ 0.912432] io scheduler deadline registered (default)
  105. [ 0.918597] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  106. [ 0.926287] console [ttyS0] disabled
  107. [ 0.950494] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
  108. [ 0.960302] console [ttyS0] enabled
  109. [ 1.043861] bootconsole [early0] disabled
  110. [ 1.143863] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
  111. [ 1.220083] nand: Winbond NAND 128MiB 3,3V 8-bit
  112. [ 1.275452] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
  113. [ 1.366360] Scanning device for bad blocks
  114. [ 1.419311] random: fast init done
  115. [ 1.509822] Creating 3 MTD partitions on "ar934x-nfc":
  116. [ 1.571550] 0x000000000000-0x000000040000 : "booter"
  117. [ 1.633217] 0x000000040000-0x000000400000 : "kernel"
  118. [ 1.695081] 0x000000400000-0x000008000000 : "ubi"
  119. [ 1.757576] libphy: Fixed MDIO Bus: probed
  120. [ 1.820312] libphy: ag71xx_mdio: probed
  121. [ 2.490039] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
  122. [ 2.600503] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
  123. [ 3.299989] ag71xx-mdio.1: Found an AR934X built-in switch
  124. [ 3.412402] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
  125. [ 3.486770] NET: Registered protocol family 10
  126. [ 3.544676] NET: Registered protocol family 17
  127. [ 3.598032] 8021q: 802.1Q VLAN Support v1.8
  128. [ 3.648479] rb: debug: id = 26
  129. [ 3.686082] rb: debug: id = 4
  130. [ 3.722688] rb: debug: id = 14
  131. [ 3.760347] rb: debug: id = 10
  132. [ 3.798006] rb: debug: id = 13
  133. [ 3.835666] rb: debug: id = 19
  134. [ 3.873324] rb: debug: id = 18
  135. [ 3.910984] rb: debug: id = 20
  136. [ 3.948645] rb: debug: id = 21
  137. [ 3.986304] rb: debug: id = 27
  138. [ 4.023962] rb: debug: id = 11
  139. [ 4.061625] rb: debug: id = 5
  140. [ 4.098239] rb: debug: id = 33
  141. [ 4.135899] rb: debug: id = 6
  142. [ 4.172514] rb: debug: id = 25
  143. [ 4.210174] rb: debug: id = 3
  144. [ 4.246791] rb: debug: id = 1
  145. [ 4.283407] rb: debug: id = 23
  146. [ 4.321066] rb: debug: id = 8
  147. [ 4.357683] rb: debug: id = 28
  148. [ 4.395342] rb: debug: id = 22
  149. [ 4.436760] UBI: auto-attach mtd2
  150. [ 4.476557] ubi0: attaching mtd2
  151. [ 5.742909] ubi0: scanning is finished
  152. [ 5.806889] ubi0: attached mtd2 (name "ubi", size 124 MiB)
  153. [ 5.872772] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  154. [ 5.955247] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  155. [ 6.036723] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
  156. [ 6.120282] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
  157. [ 6.192367] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
  158. [ 6.279059] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1710670049
  159. [ 6.388697] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20
  160. [ 6.499439] ubi0: background thread "ubi_bgt0d" started, PID 280
  161. [ 6.573572] block ubiblock0_1: created from ubi0:1(rootfs)
  162. [ 6.639422] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
  163. [ 6.730835] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
  164. [ 6.817678] Freeing unused kernel memory: 228K
  165. [ 6.870990] This architecture does not have kernel memory protection.
  166. [ 7.645458] init: Console is alive
  167. [ 7.686536] init: - watchdog -
  168. [ 8.663184] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  169. [ 8.802359] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  170. [ 8.899524] init: - preinit -
  171. [ 9.585095] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  172. [ 9.679791] random: procd: uninitialized urandom read (4 bytes read)
  173. [ 13.014993] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 337
  174. [ 13.301432] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
  175. [ 13.395500] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  176. [ 13.514496] UBIFS (ubi0:2): FS size: 117833728 bytes (112 MiB, 928 LEBs), journal size 5840896 bytes (5 MiB, 46 LEBs)
  177. [ 13.641864] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
  178. [ 13.721255] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID BC3A5EDF-3491-48D9-B7EC-3750C006716B, small LPT model
  179. [ 13.860062] mount_root: overlay filesystem has not been fully initialized yet
  180. [ 13.948374] mount_root: switching to ubifs overlay
  181. [ 14.053556] random: crng init done
  182. [ 14.168023] urandom-seed: Seed file not found (/etc/urandom.seed)
  183. [ 14.461114] procd: - early -
  184. [ 14.495772] procd: - watchdog -
  185. [ 15.152974] procd: - watchdog -
  186. [ 15.190926] procd: - ubus -
  187. [ 15.325429] procd: - init -
  188. [ 15.790943] kmodloader: loading kernel modules from /etc/modules.d/*
  189. [ 15.872595] ip6_tables: (C) 2000-2006 Netfilter Core Team
  190. [ 15.950394] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
  191. [ 16.046477] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
  192. [ 16.134212] ip_tables: (C) 2000-2006 Netfilter Core Team
  193. [ 16.207330] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
  194. [ 16.337719] xt_time: kernel timezone is -0000
  195. [ 16.451619] PPP generic driver version 2.4.2
  196. [ 16.505749] NET: Registered protocol family 24
  197. [ 16.603516] kmodloader: done loading kernel modules from /etc/modules.d/*
  198. [ 27.854823] br-lan: port 1(eth1) entered blocking state
  199. [ 27.917581] br-lan: port 1(eth1) entered disabled state
  200. [ 27.980648] device eth1 entered promiscuous mode
  201. [ 28.122075] br-lan: port 1(eth1) entered blocking state
  202. [ 28.184840] br-lan: port 1(eth1) entered forwarding state
  203. [ 28.249779] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  204. [ 28.343920] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  205. [ 28.748504] br-lan: port 1(eth1) entered disabled state
  206. [ 29.559941] eth1: link up (1000Mbps/Full duplex)
  207. [ 29.822351] br-lan: port 1(eth1) entered blocking state
  208. [ 29.885046] br-lan: port 1(eth1) entered forwarding state
  209. [ 30.258311] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!