Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- sudo smartctl -a /dev/sda
- smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-29-generic] (local build)
- Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Device Model: ADATA SU650
- Serial Number: 2I0920012878
- LU WWN Device Id: 5 000000 000000000
- Firmware Version: B170428a
- User Capacity: 120,034,123,776 bytes [120 GB]
- Sector Size: 512 bytes logical/physical
- Rotation Rate: Solid State Device
- Form Factor: 2.5 inches
- Device is: Not in smartctl database [for details use: -P showall]
- ATA Version is: ACS-2 (minor revision not indicated)
- SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Wed Sep 12 14:50:31 2018 UTC
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x00) Offline data collection activity
- was never started.
- Auto Offline Data Collection: Disabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 33) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 1) minutes.
- Extended self-test routine
- recommended polling time: ( 1) minutes.
- Conveyance self-test routine
- recommended polling time: ( 1) minutes.
- SCT capabilities: (0x0039) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 0
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1595
- 12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 9
- 167 Unknown_Attribute 0x0022 100 100 000 Old_age Always - 0
- 168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 136
- 169 Unknown_Attribute 0x0013 094 094 010 Pre-fail Always - 103080788403
- 173 Unknown_Attribute 0x0012 200 200 000 Old_age Always - 30069424146
- 175 Program_Fail_Count_Chip 0x0013 052 100 010 Pre-fail Always - 0
- 180 Unused_Rsvd_Blk_Cnt_Tot 0x0033 094 094 020 Pre-fail Always - 432
- 192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 8
- 194 Temperature_Celsius 0x0022 070 070 030 Old_age Always - 30 (Min/Max 30/40)
- 231 Temperature_Celsius 0x0033 095 095 005 Pre-fail Always - 1280
- 233 Media_Wearout_Indicator 0x0032 100 100 000 Old_age Always - 3034286848
- 234 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 704123748352
- 241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 1720065287
- 242 Total_LBAs_Read 0x0032 100 100 000 Old_age Always - 683591073
- SMART Error Log Version: 1
- ATA Error Count: 2
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 2 occurred at disk power-on lifetime: 1394 hours (58 days + 2 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 84 51 00 00 00 00 a0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ec 00 00 00 00 00 a0 08 8d+08:22:12.404 IDENTIFY DEVICE
- e7 00 00 00 00 00 a0 08 8d+08:22:04.204 FLUSH CACHE
- e7 00 00 00 00 00 a0 08 8d+08:22:04.204 FLUSH CACHE
- e7 00 00 00 00 00 a0 08 8d+08:22:04.104 FLUSH CACHE
- e7 00 00 00 00 00 a0 08 8d+08:22:04.104 FLUSH CACHE
- Error 1 occurred at disk power-on lifetime: 1394 hours (58 days + 2 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 00 58 00 00 00 00 a0
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- ec 00 00 00 00 00 a0 08 8d+08:22:12.404 IDENTIFY DEVICE
- e7 00 00 00 00 00 a0 08 8d+08:22:04.204 FLUSH CACHE
- e7 00 00 00 00 00 a0 08 8d+08:22:04.204 FLUSH CACHE
- e7 00 00 00 00 00 a0 08 8d+08:22:04.104 FLUSH CACHE
- e7 00 00 00 00 00 a0 08 8d+08:22:04.104 FLUSH CACHE
- SMART Self-test log structure revision number 1
- Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
- # 1 Short offline Completed without error 00% 1556 -
- # 2 Short offline Completed without error 00% 824 -
- # 3 Short offline Completed without error 00% 80 -
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement