U-Boot SPL 2020.04-armbian (Jun 02 2020 - 17:17:54 +0200)
DRAM: 2048 MiB
Trying to boot from MMC2
NOTICE:  BL31: v2.3(debug):ec29ce6-dirty
NOTICE:  BL31: Built : 17:17:45, Jun  2 2020
NOTICE:  BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE:  BL31: Found U-Boot DTB at 0x4095f08, model: BananaPi-M64
INFO:    ARM GICv2 driver initialized
INFO:    Configuring SPC Controller
INFO:    PMIC: Probing AXP803 on RSB
INFO:    PMIC: Enabling DRIVEVBUS
INFO:    PMIC: dcdc1 voltage: 3.300V
INFO:    PMIC: dcdc5 voltage: 1.500V
INFO:    PMIC: dcdc6 voltage: 1.100V
INFO:    PMIC: dldo1 voltage: 3.300V
INFO:    PMIC: dldo2 voltage: 3.300V
INFO:    PMIC: Enabling DC SW
INFO:    BL31: Platform setup done
INFO:    BL31: Initializing runtime services
INFO:    BL31: cortex_a53: CPU workaround for 843419 was applied
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
NOTICE:  PSCI: System suspend is unavailable
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x4a000000
INFO:    SPSR = 0x3c9


U-Boot 2020.04-armbian (Jun 02 2020 - 17:17:54 +0200) Allwinner Technology

CPU:   Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM:  2 GiB
MMC:   Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... Unable to use mmc 1:1... In:    serial@1c28000
Out:   serial@1c28000
Err:   serial@1c28000
Allwinner mUSB OTG (Peripheral)
Net:   phy interface7
eth0: ethernet@1c30000
Warning: usb_ether using MAC address from ROM
, eth1: usb_ether
starting USB...
Bus usb@1c1a000: USB EHCI 1.00
Bus usb@1c1a400: USB OHCI 1.0
Bus usb@1c1b000: USB EHCI 1.00
Bus usb@1c1b400: USB OHCI 1.0
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
scanning bus usb@1c1b000 for devices...
      USB device not accepting new address (error=20)
11 USB Device(s) found
scanning bus usb@1c1b400 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Autoboot in 1 seconds, press <Space> to stop
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
3033 bytes read in 2 ms (1.4 MiB/s)
## Executing script at 4fc00000
U-boot loaded from eMMC or secondary SD
Boot script loaded from mmc
153 bytes read in 2 ms (74.2 KiB/s)
MMC: no card present
39130 bytes read in 4 ms (9.3 MiB/s)
3821 bytes read in 4 ms (932.6 KiB/s)
Applying kernel provided DT fixup script (sun50i-a64-fixup.scr)
## Executing script at 44000000
15248871 bytes read in 730 ms (19.9 MiB/s)
17162752 bytes read in 822 ms (19.9 MiB/s)
## Loading init Ramdisk from Legacy Image at 4fe00000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    15248807 Bytes = 14.5 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
   Booting using the fdt blob at 0x4fa00000
   Loading Ramdisk to 49175000, end 49fffda7 ... OK
   Loading Device Tree to 0000000049103000, end 0000000049174fff ... OK

Starting kernel ...

[    6.767243] lima 1c40000.gpu: IRQ ppmmu2 not found
[    6.776717] lima 1c40000.gpu: IRQ ppmmu3 not found
[    6.786286] lima 1c40000.gpu: IRQ pp2 not found
[    6.795350] lima 1c40000.gpu: IRQ pp3 not found
[    7.506783] usbhid 3-1.2.1.2.4.3:1.1: couldn't find an input interrupt endpoint

Armbian 20.05.2 Focal ttyS0

bananapim64 login: