Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- radxa-zero boot mainline 5.13 kernel, amlogic/custodian u-boot, radxa FIP files
- G12A:BL:0253b8:61aa2d;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;CHK:1F;READ:0;CHK:1F;READ:0;CHK:1F;SD?:0;SD:0;READ:0;0.0
- bl2_stage_init 0x02
- no sdio debug board detected
- L0:00000000
- L1:00000703
- L2:00008067
- L3:04000000
- S1:00000000
- B2:00002000
- B1:e0f83180
- TE: 447900
- BL2 Built : 15:21:48, Aug 28 2019. g12a g1bf2b53 - luan.yuan@droid15-sz
- Board ID = 2
- Set cpu clk to 24M
- Set clk81 to 24M
- CPU clk: 1200 MHz
- Set clk81 to 166.6M
- DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:21:45
- board id: 2
- Load FIP HDR from SD, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
- fw parse done
- Load ddrfw from SD, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0
- Load ddrfw from SD, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0
- PIEI prepare done
- fastboot data load
- fastboot data verify
- verify result: 266
- Cfg max: 2, cur: 1. Board id: 255. Force loop cfg
- LPDDR4 probe
- ddr clk to 792MHz
- Load ddrfw from SD, src: 0x0003c200, des: 0xfffd0000, size: 0x0000c000, part: 0
- dmc_version 0000
- Check phy result
- INFO : End of CA training
- INFO : End of initialization
- INFO : Training has run successfully!
- Check phy result
- INFO : End of initialization
- INFO : End of read enable training
- INFO : End of fine write leveling
- INFO : End of Write leveling coarse delay
- INFO : Training has run successfully!
- Check phy result
- INFO : End of initialization
- INFO : End of read dq deskew training
- INFO : End of MPR read delay center optimization
- INFO : End of write delay center optimization
- INFO : End of read delay center optimization
- INFO : End of max read latency training
- INFO : Training has run successfully!
- 1D training succeed
- Load ddrfw from SD, src: 0x00048200, des: 0xfffd0000, size: 0x0000c000, part: 0
- Check phy result
- INFO : End of initialization
- INFO : End of 2D read delay Voltage center optimization
- INFO : End of 2D read delay Voltage center optimization
- INFO : End of 2D write delay Voltage center optimization
- INFO : End of 2D write delay Voltage center optimization
- INFO : Training has run successfully!
- channel==0
- RxClkDly_Margin_A0==236 ps 12
- TxDqDly_Margin_A0==216 ps 11
- RxClkDly_Margin_A1==256 ps 13
- TxDqDly_Margin_A1==216 ps 11
- TrainedVREFDQ_A0==75
- TrainedVREFDQ_A1==74
- VrefDac_Margin_A0==32
- DeviceVref_Margin_A0==39
- VrefDac_Margin_A1==32
- DeviceVref_Margin_A1==40
- channel==1
- RxClkDly_Margin_A0==216 ps 11
- TxDqDly_Margin_A0==216 ps 11
- RxClkDly_Margin_A1==256 ps 13
- TxDqDly_Margin_A1==236 ps 12
- TrainedVREFDQ_A0==74
- TrainedVREFDQ_A1==74
- VrefDac_Margin_A0==33
- DeviceVref_Margin_A0==40
- VrefDac_Margin_A1==31
- DeviceVref_Margin_A1==40
- dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
- soc_vref_reg_value 0x 0000001a 0000001d 0000001b 0000001d 0000001c 0000001d 0000001d 0000001b 0000001c 0000001b 0000001c 0000001c 0000001d 0000001d 0000001d 0000001e 0000001c 0000001c 0000001b 0000001a 0000001d 0000001e 0000001d 0000001f 0000001c 0000001a
- 0000001b 0000001c 0000001c 0000001b 0000001b 0000001d dram_vref_reg_value 0x 0000005c
- 2D training succeed
- aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:53:31
- auto size-- 65535DDR cs0 size: 1024MB
- DDR cs1 size: 1024MB
- DMC_DDR_CTRL: 00e0001bDDR size: 2048MB
- cs0 DataBus test pass
- cs1 DataBus test pass
- cs0 AddrBus test pass
- cs1 AddrBus test pass
- 100bdlr_step_size ps== 460
- result report
- boot times 0Enable ddr reg access
- Load FIP HDR from SD, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
- Load BL3X from SD, src: 0x0006c200, des: 0x0175c000, size: 0x00098000, part: 0
- bl2z: ptr: 05129330, size: 00001e40
- 0.0;M3 CHK:0;cm4_sp_mode 0
- MVN_1=0x00000000
- MVN_2=0x00000000
- [Image: g12a_v1.1.3390-6ac5299 2019-09-26 14:09:46 luan.yuan@droid15-sz]
- OPS=0x30
- ring efuse init
- 28 0b 30 00 01 08 12 00 00 14 35 39 53 42 56 50
- [0.017150 Inits done]
- secure task start!
- high task start!
- low task start!
- run into bl31
- NOTICE: BL31: v1.3(release):4fc40b1
- NOTICE: BL31: Built : 15:57:33, May 22 2019
- NOTICE: BL31: G12A normal boot!
- NOTICE: BL31: BL33 decompress pass
- ERROR: Error initializing runtime service opteed_fast
- U-Boot 2021.07-rc3 (Jul 09 2021 - 18:33:25 +0200) radxazero
- Model: Radxa Zero
- SoC: Amlogic Meson G12A (Unknown) Revision 28:b (30:2)
- DRAM: 2 GiB
- MMC: sd@ffe03000: 0, sd@ffe05000: 1, mmc@ffe07000: 2
- Loading Environment from nowhere... OK
- In: serial
- Out: serial
- Err: serial
- Net: No ethernet found.
- Hit any key to stop autoboot: 0
- Card did not respond to voltage select! : -110
- switch to partitions #0, OK
- mmc1 is current device
- Scanning mmc 1:1...
- Found U-Boot script /boot.scr
- 1468 bytes read in 2 ms (716.8 KiB/s)
- ## Executing script at 08000000
- 30988800 bytes read in 1359 ms (21.7 MiB/s)
- Failed to load '/g12a_dtb'
- 48868 bytes read in 7 ms (6.7 MiB/s)
- Failed to load '/initramfs-linux.img'
- Moving Image from 0x8080000 to 0x8200000, end=a020000
- ## Flattened Device Tree blob at 08008000
- Booting using the fdt blob at 0x8008000
- Loading Device Tree to 000000003fff1000, end 000000003fffffff ... OK
- Starting kernel ...
- [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
- [ 0.000000] Linux version 5.13.1 (piotro@minimyth-armv8) (aarch64-minimyth-linux-gnu-gcc (GCC) 10.3.0, GNU ld (GNU Binutils)
- 2.36) #1 SMP PREEMPT Thu Jul 8 09:20:14 CEST 2021
- [ 0.000000] Machine model: Radxa Zero
- [ 0.000000] efi: UEFI not found.
- [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'secmon@5000000': base 0x0000000005000000, size 3 MiB
- [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000047c00000, size 896 MiB
- [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
- [ 0.000000] earlycon: meson0 at MMIO 0x00000000ff803000 (options '115200n8')
- [ 0.000000] printk: bootconsole [meson0] enabled
- [ 0.000000] Zone ranges:
- [ 0.000000] DMA [mem 0x0000000000000000-0x000000007fe5afff]
- [ 0.000000] DMA32 empty
- [ 0.000000] Normal empty
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000052fffff]
- [ 0.000000] node 0: [mem 0x0000000005300000-0x00000000072fffff]
- [ 0.000000] node 0: [mem 0x0000000007300000-0x000000007fe5afff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fe5afff]
- [ 0.000000] On node 0 totalpages: 523867
- [ 0.000000] DMA zone: 8186 pages used for memmap
- [ 0.000000] DMA zone: 0 pages reserved
- [ 0.000000] DMA zone: 523867 pages, LIFO batch:63
- [ 0.000000] DMA zone: 421 pages in unavailable ranges
- [ 0.000000] psci: probing for conduit method from DT.
- [ 0.000000] psci: PSCIv1.0 detected in firmware.
- [ 0.000000] psci: Using standard PSCI v0.2 function IDs
- [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
- [ 0.000000] psci: SMC Calling Convention v1.1
- [ 0.000000] percpu: Embedded 33 pages/cpu s95128 r8192 d31848 u135168
- [ 0.000000] pcpu-alloc: s95128 r8192 d31848 u135168 alloc=33*4096
- [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
- [ 0.000000] Detected VIPT I-cache on CPU0
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 515681
- [ 0.000000] Kernel command line: root=PARTUUID=346d1a6a-02 rw rootwait earlycon console=ttyS0,115200n8 debug MM_DEBUG=yes
- [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 1070472K/2095468K available (14400K kernel code, 3318K rwdata, 6260K rodata, 6144K init, 558K bss, 107492K reserved, 917504K cma-reserved)
- [ 0.000000] random: get_random_u64 called from cache_random_seq_create+0x8c/0x190 with crng_init=0
- [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
- [ 0.000000] ftrace: allocating 50052 entries in 196 pages
- [ 0.000000] ftrace: allocated 196 pages with 3 groups
- [ 0.000000] trace event string verifier disabled
- [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
- [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
- [ 0.000000] Trampoline variant of Tasks RCU enabled.
- [ 0.000000] Rude variant of Tasks RCU enabled.
- [ 0.000000] Tracing variant of Tasks RCU enabled.
- [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
- [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
- [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
- [ 0.000000] Root IRQ handler: gic_handle_irq
- [ 0.000000] GIC: Using split EOI/Deactivate mode
- [ 0.000000] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
- [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
- [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
- [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
- [ 0.008315] Console: colour dummy device 80x25
- [ 0.012549] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
- [ 0.022842] pid_max: default: 32768 minimum: 301
- [ 0.027634] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
- [ 0.034926] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
- [ 0.044631] rcu: Hierarchical SRCU implementation.
- [ 0.050086] EFI services will not be available.
- [ 0.052689] smp: Bringing up secondary CPUs ...
- [ 0.057384] Detected VIPT I-cache on CPU1
- [ 0.057451] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
- [ 0.058123] Detected VIPT I-cache on CPU2
- [ 0.058156] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
- [ 0.058802] Detected VIPT I-cache on CPU3
- [ 0.058830] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
- [ 0.058912] smp: Brought up 1 node, 4 CPUs
- [ 0.092598] SMP: Total of 4 processors activated.
- [ 0.097308] CPU features: detected: 32-bit EL0 Support
- [ 0.102466] CPU features: detected: 32-bit EL1 Support
- [ 0.107652] CPU features: detected: CRC32 instructions
- [ 0.121857] CPU: All CPU(s) started at EL2
- [ 0.121931] alternatives: patching kernel code
- [ 0.125827] devtmpfs: initialized
- [ 0.138487] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
- [ 0.142662] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
- [ 0.181180] pinctrl core: initialized pinctrl subsystem
- [ 0.181881] DMI not present or invalid.
- [ 0.184989] NET: Registered protocol family 16
- [ 0.191224] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
- [ 0.196371] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
- [ 0.204232] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
- [ 0.212036] audit: initializing netlink subsys (disabled)
- [ 0.217527] audit: type=2000 audit(0.146:1): state=initialized audit_enabled=0 res=1
- [ 0.218950] thermal_sys: Registered thermal governor 'fair_share'
- [ 0.225154] thermal_sys: Registered thermal governor 'bang_bang'
- [ 0.231267] thermal_sys: Registered thermal governor 'step_wise'
- [ 0.237304] thermal_sys: Registered thermal governor 'user_space'
- [ 0.243725] cpuidle: using governor ladder
- [ 0.253598] cpuidle: using governor menu
- [ 0.257634] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- [ 0.264451] ASID allocator initialised with 65536 entries
- [ 0.270871] Serial: AMBA PL011 UART driver
- [ 0.314986] cryptd: max_cpu_qlen set to 1000
- [ 0.318039] ACPI: Interpreter disabled.
- [ 0.318513] reg-fixed-voltage regulator-ao_5v: Failed to register regulator: -517
- [ 0.325387] reg-fixed-voltage regulator-emmc_1v8: Failed to register regulator: -517
- [ 0.332890] VDDAO_3V3: supplied by DC_IN
- [ 0.337336] VDDIO_AO1V8: supplied by VDDAO_3V3
- [ 0.341780] iommu: Default domain type: Translated
- [ 0.346428] vgaarb: loaded
- [ 0.349560] SCSI subsystem initialized
- [ 0.352765] usbcore: registered new interface driver usbfs
- [ 0.358121] usbcore: registered new interface driver hub
- [ 0.363450] usbcore: registered new device driver usb
- [ 0.369009] pps_core: LinuxPPS API ver. 1 registered
- [ 0.373482] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
- [ 0.382679] PTP clock support registered
- [ 0.386640] EDAC MC: Ver: 3.0.0
- [ 0.390543] Advanced Linux Sound Architecture Driver Initialized.
- [ 0.396718] clocksource: Switched to clocksource arch_sys_counter
- [ 0.477708] pnp: PnP ACPI: disabled
- [ 0.484890] NET: Registered protocol family 2
- [ 0.485075] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
- [ 0.492159] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
- [ 0.499713] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
- [ 0.507700] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
- [ 0.515162] TCP: Hash tables configured (established 16384 bind 16384)
- [ 0.521672] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
- [ 0.528286] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
- [ 0.535614] NET: Registered protocol family 1
- [ 0.540344] RPC: Registered named UNIX socket transport module.
- [ 0.545766] RPC: Registered udp transport module.
- [ 0.550470] RPC: Registered tcp transport module.
- [ 0.555192] RPC: Registered tcp NFSv4.1 backchannel transport module.
- [ 0.561685] NET: Registered protocol family 44
- [ 0.566141] PCI: CLS 0 bytes, default 64
- [ 0.571143] kvm [1]: IPA Size Limit: 40 bits
- [ 0.575697] kvm [1]: vgic interrupt IRQ9
- [ 0.578426] kvm: pmu event creation failed -2
- [ 0.582711] kvm [1]: Hyp mode initialized successfully
- [ 1.191551] Initialise system trusted keyrings
- [ 1.191864] workingset: timestamp_bits=46 max_order=19 bucket_order=0
- [ 1.202224] zbud: loaded
- [ 1.203856] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 1.205893] NFS: Registering the id_resolver key type
- [ 1.210357] Key type id_resolver registered
- [ 1.214515] Key type id_legacy registered
- [ 1.218625] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
- [ 1.225279] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
- [ 1.270063] NET: Registered protocol family 38
- [ 1.270096] Key type asymmetric registered
- [ 1.272964] Asymmetric key parser 'x509' registered
- [ 1.277874] Asymmetric key parser 'pkcs8' registered
- [ 1.282860] Key type pkcs7_test registered
- [ 1.287008] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
- [ 1.294538] io scheduler mq-deadline registered
- [ 1.298969] io scheduler kyber registered
- [ 1.303156] io scheduler bfq registered
- [ 1.319646] EINJ: ACPI disabled.
- [ 1.331212] soc soc0: Amlogic Meson G12A (Unknown) Revision 28:b (30:2) Detected
- [ 1.336603] Serial: 8250/16550 driver, 4 porv 1.342841] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 24, base_baud = 1500000) is a meson_uart
- [ 1.347450] ffd24000.serial: ttyAML6 at MMIO 0xffd24000 (irq = 30, base_baud = 1500000) is a meson_uart
- [ 1.356164] serial serial0: tty port ttyAML6 registered
- [ 1.371351] libphy: Fixed MDIO Bus: probed
- [ 1.374717] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 1.376382] ehci-pci: EHCI PCI platform driver
- [ 1.380881] ehci-platform: EHCI generic platform driver
- [ 1.386441] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 1.392316] ohci-pci: OHCI PCI platform driver
- [ 1.396801] ohci-platform: OHCI generic platform driver
- [ 1.402609] usbcore: registered new interface driver usb-storage
- [ 1.408092] usbcore: registered new interface driver ums-realtek
- [ 1.414173] usbcore: registered new interface driver usbserial_generic
- [ 1.420678] usbserial: USB Serial support registered for generic
- [ 1.428242] mousedev: PS/2 mouse device common for all mice
- [ 1.436586] sdhci: Secure Digital Host Controller Interface driver
- [ 1.438518] sdhci: Copyright(c) Pierre Ossman
- [ 1.443231] Synopsys Designware Multimedia Card Interface Driver
- [ 1.450685] sdhci-pltfm: SDHCI platform and OF driver helper
- [ 1.450728] meson-gx-mmc ffe05000.sd: Got CD GPIO
- [ 1.459410] ledtrig-cpu: registered to indicate activity on CPUs
- [ 1.466282] meson-sm: secure-monitor enabled
- [ 1.469882] hid: raw HID events driver (C) Jiri Kosina
- [ 1.474938] usbcore: registered new interface driver usbhid
- [ 1.480420] usbhid: USB HID core driver
- [ 1.491644] NET: Registered protocol family 17
- [ 1.491896] Key type dns_resolver registered
- [ 1.495593] registered taskstats version 1
- [ 1.498876] Loading compiled-in X.509 certificates
- [ 1.504097] zswap: loaded using pool lzo/zbud
- [ 1.530268] mmc0: new high speed SDHC card at address 1234
- [ 1.531240] mmcblk0: mmc0:1234 SA16G 14.4 GiB
- [ 1.532350] AO_5V: supplied by DC_IN
- [ 1.537371] mmcblk0: p1 p2
- [ 1.538812] EMMC_1V8: supplied by VDDAO_3V3
- [ 1.545842] VDDAO_3V3_T: supplied by VDDAO_3V3
- [ 1.633772] meson-drm ff900000.vpu: Queued 2 outputs on vpu
- [ 1.634478] meson-drm ff900000.vpu: CVBS Output connector not available
- [ 1.666771] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
- [ 1.671352] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver
- [ 1.679633] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops)
- [ 1.686995] [drm] Initialized meson 1.0.0 20161109 for ff900000.vpu on minor 0
- [ 1.884298] Console: switching to colour frame buffer device 128x48
- [ 1.901079] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device
- [ 1.910484] simple-framebuffer 7fe5b000.framebuffer: framebuffer at 0x7fe5b000, 0x195000 bytes
- [ 1.916942] simple-framebuffer 7fe5b000.framebuffer: format=x8r8g8b8, mode=720x576x32, linelength=2880
- [ 1.926474] simple-framebuffer 7fe5b000.framebuffer: fb1: simplefb registered!
- [ 1.939132] ALSA device list:
- [ 1.939172] No soundcards found.
- [ 1.939982] Warning: unable to open an initial console.
- [ 2.883515] EXT4-fs (mmcblk0p2): recovery complete
- [ 2.883567] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled.
- [ 2.892902] VFS: Mounted root (ext4 filesystem) on device 179:2.
- [ 2.900846] devtmpfs: mounted
- [ 2.908672] Freeing unused kernel memory: 6144K
- [ 2.908830] Run /sbin/init as init process
- [ 2.911731] with arguments:
- [ 2.914673] /sbin/init
- [ 2.917386] with environment:
- [ 2.920536] HOME=/
- [ 2.922889] TERM=linux
- [ 2.925611] MM_DEBUG=yes
- [ 3.097993] random: fast init done
- [ 3.226941] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100
- [ 3.228985] CPU: 2 PID: 1 Comm: init Not tainted 5.13.1 #1
- [ 3.234494] Hardware name: Radxa Zero (DT)
- [ 3.238608] Call trace:
- [ 3.241057] dump_backtrace+0x0/0x1e0
- [ 3.244732] show_stack+0x20/0x2c
- [ 3.248057] dump_stack+0xd0/0x128
- [ 3.251469] panic+0x174/0x374
- [ 3.254532] do_exit+0x3f0/0x45c
- [ 3.257769] do_group_exit+0x40/0xa0
- [ 3.261357] __wake_up_parent+0x0/0x40
- [ 3.265119] invoke_syscall.constprop.0+0x58/0xf0
- [ 3.269844] el0_svc_common.constprop.0+0x54/0x154
- [ 3.274657] do_el0_svc+0x24/0xac
- [ 3.277982] el0_svc+0x24/0x34
- [ 3.281044] el0_sync_handler+0xb0/0xc0
- [ 3.284894] el0_sync+0x198/0x1c0
- [ 3.288226] SMP: stopping secondary CPUs
- [ 3.292163] Kernel Offset: disabled
- [ 3.295657] CPU features: 0x00000001,00000846
- [ 3.300032] Memory Limit: none
- [ 3.303102] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100 ]---
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement