NAS eTRAYz Xtreamer with HDD and OS

U-Boot 1.1.2 (Jan 19 2010 - 17:23:36)

U-Boot code: 48D00000 -> 48D1B860  BSS: -> 48D1F670
RAM Configuration:
        Bank #0: 48000000 128 MB
SRAM Configuration:
        128KB at 0x58000000
Flash:  4 MB
In:    serial
Out:   serial
Err:   serial
Extinguish LED
Light LED
Initialising disks
No FIS received from device 0
No FIS received from device 0
Detecting SATA busses:
Bus 0: Found second device OK
  Device 0: not available
  Device 1: Model: SAMSUNG HD321KJ  Firm: CP100-12 Ser#: S0MQJDWPB31777
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)

IDE read: device 1 block # 288, count 1 ... 1 blocks read: OK
Hit any key to stop autoboot:  0

IDE device 0: not available

IDE device 0: not available
Light LED

IDE device 1: Model: SAMSUNG HD321KJ  Firm: CP100-12 Ser#: S0MQJDWPB31777
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
... is now current device

IDE read: device 1 block # 290, count 5700 ... 5700 blocks read: OK
Extinguish LED
## Booting image at 48500000 ...
   Image Name:   Linux-2.6.24.4
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2013972 Bytes =  1.9 MB
   Load Address: 48008000
   Entry Point:  48008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................................................... done, booting the kernel.
Linux version 2.6.24.4 (root@etrayz-build) (gcc version 4.2.4) #1 Tue May 4 17:44:30 KST 2010
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: Oxsemi NAS
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/md0 ro mac_adr=0x00,0x1c,0x85,0x20,0x4a,0xfe mem=128M poweroutage=yes
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125824KB available (3708K code, 203K data, 116K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 64 bytes
NET: Registered protocol family 16
Number of DMA channels = 5, version = 4
Allocating 891 SRAM generic DMA descriptors
Chip Id: die-id 0x0dc9da7170c0 read back 0xbeefcafe
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
Init Macpower NT2-GIGA-NAS(OX810) GPIO driver...
GPIO driver registered
thermAndFan: initializing - ox810
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
fuse init (API version 7.9)
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
�serial8250: ttyS0 at MMIO 0x44900000 (irq = 0) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
Linux video capture interface: v2.00
Driver 'sd' needs updating - please use bus_type methods
ox810sata: OX810 sata core.
scsi0 : oxnassata
ata1: SATA max UDMA/133 irq 18
ata1: SATA link down (SStatus 0 SControl 300)
ox810sata: OX810 sata core.
scsi1 : oxnassata
ata2: SATA max UDMA/133 irq 18
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-8: SAMSUNG HD321KJ, CP100-12, max UDMA7
ata2.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      SAMSUNG HD321KJ  CP10 PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 1:0:0:0: [sda] Attached SCSI disk
physmap platform flash device: 00400000 at 41000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-ds1307 0-0068: rtc core: registered m41t00 as rtc0
OXNAS bit-bash I2C driver initialisation OK
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-ds1307 0-0068: setting system clock to 2017-08-07 18:07:01 UTC (1502129221)
md: Autodetecting RAID arrays.
md: Scanned 2 and added 2 devices.
md: autorun ...
md: considering sda2 ...
md:  adding sda2 ...
md: sda1 has different UUID to sda2
md: created md1
md: bind<sda2>
md: running: <sda2>
raid1: raid set md1 active with 1 out of 2 mirrors
raid1 not hw raidable, needs two working disks.
md: considering sda1 ...
md:  adding sda1 ...
md: created md0
md: bind<sda1>
md: running: <sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
raid1 not hw raidable, needs two working disks.
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing init memory: 116K
INIT: version 2.87 booting
Mon Aug  7 21:07:02 EEST 2017
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb

                Welcome to e-TRAYz NAS 1.0.5-official
Setting hostname NAS:  [  OK  ]
Checking filesystems
/dev/md0: clean, 42148/124160 files, 273460/495856 blocks [  OK  ]
Remounting root filesystem in read-write mode: [  OK  ]
Mounting local filesystems: [  OK  ]
Enabling /etc/fstab swaps:  swapon:
INIT: Entering runlevel: 3so.1:
Applying iptables firewall rules: [  OK  ]
Bringing up loopback interface:  [  OK  ]
Bringing up interface eth0: [  OK  ]
Starting syslog-ng: [  OK  ]
Starting portmap: [  OK  ]
Starting mdmonitor: [  OK  ]
Starting volume: [  OK  ]
Starting usb: [  OK  ]
Starting NFS services: exportfs: Warning: /home/Public/PXE/pxelinux.cfg/images/livecd/SystemRescueCD does not exist [  OK  ]
Starting NFS daemon: [  OK  ]
Starting NFS mountd: [  OK  ]
Starting MySQL..[  OK  ]
Starting apache2: /usr/sbin/apache2: [  OK  ]
Starting license: [  OK  ]
Starting rsync services: [  OK  ]
Starting rtorrent services: [  OK  ]
Starting sshd: [  OK  ]
Starting cron: [  OK  ]
Starting NMB services: [  OK  ]
Starting SMB services: [  OK  ]
Starting telnetd: [  OK  ]
Starting DDNS Renew: [ DONE ]
Starting StandBy Internal Disk: [ DONE ]
Starting StandBy External Disk: [ DONE ] [  OK  ]
etrayz: [  OK  ]
Starting epkg: [  OK  ]


Xtreamer e-TRAYz Personal Network Storage

NAS login: