Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- # smartctl -a /dev/sdb | less
- smartctl 7.0 2018-12-30 r4883 [x86_64-linux-3.10.0-1160.66.1.el7.x86_64] (local build)
- Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
- === START OF INFORMATION SECTION ===
- Device Model: ST16000NM001G-2KK103
- Serial Number: ZL753JYG
- LU WWN Device Id: 5 000c50 0b5d76226
- Firmware Version: SN02
- User Capacity: 16,000,900,661,248 bytes [16.0 TB]
- Sector Sizes: 512 bytes logical, 4096 bytes physical
- Rotation Rate: 7200 rpm
- Form Factor: 3.5 inches
- Device is: Not in smartctl database [for details use: -P showall]
- ATA Version is: ACS-4 (minor revision not indicated)
- SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
- Local Time is: Wed Nov 30 10:33:24 2022 CST
- SMART support is: Available - device has SMART capability.
- SMART support is: Enabled
- === START OF READ SMART DATA SECTION ===
- SMART overall-health self-assessment test result: PASSED
- General SMART Values:
- Offline data collection status: (0x82) Offline data collection activity
- was completed without error.
- Auto Offline Data Collection: Enabled.
- Self-test execution status: ( 0) The previous self-test routine completed
- without error or no self-test has ever
- been run.
- Total time to complete Offline
- data collection: ( 567) seconds.
- Offline data collection
- capabilities: (0x7b) SMART execute Offline immediate.
- Auto Offline data collection on/off support.
- Suspend Offline collection upon new
- command.
- Offline surface scan supported.
- Self-test supported.
- Conveyance Self-test supported.
- Selective Self-test supported.
- SMART capabilities: (0x0003) Saves SMART data before entering
- power-saving mode.
- Supports SMART auto save timer.
- Error logging capability: (0x01) Error logging supported.
- General Purpose Logging supported.
- Short self-test routine
- recommended polling time: ( 1) minutes.
- Extended self-test routine
- recommended polling time: (1431) minutes.
- Conveyance self-test routine
- recommended polling time: ( 2) minutes.
- SCT capabilities: (0x70bd) SCT Status supported.
- SCT Error Recovery Control supported.
- SCT Feature Control supported.
- SCT Data Table supported.
- SMART Attributes Data Structure revision number: 10
- Vendor Specific SMART Attributes with Thresholds:
- ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
- 1 Raw_Read_Error_Rate 0x000f 084 058 044 Pre-fail Always - 235539771
- 3 Spin_Up_Time 0x0003 089 089 000 Pre-fail Always - 0
- 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 13
- 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 320
- 7 Seek_Error_Rate 0x000f 086 060 045 Pre-fail Always - 355739895
- 9 Power_On_Hours 0x0032 068 068 000 Old_age Always - 28075
- 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
- 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 13
- 18 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0
- 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 140
- 188 Command_Timeout 0x0032 100 001 000 Old_age Always - 60131115268
- 190 Airflow_Temperature_Cel 0x0022 071 055 040 Old_age Always - 29 (Min/Max 20/45)
- 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 10
- 193 Load_Cycle_Count 0x0032 083 083 000 Old_age Always - 34706
- 194 Temperature_Celsius 0x0022 029 045 000 Old_age Always - 29 (0 19 0 0 0)
- 197 Current_Pending_Sector 0x0012 087 087 000 Old_age Always - 7536
- 198 Offline_Uncorrectable 0x0010 087 087 000 Old_age Offline - 7536
- 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
- 200 Multi_Zone_Error_Rate 0x0023 100 100 001 Pre-fail Always - 0
- 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 18886 (49 147 0)
- 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 390091465412
- 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3316209511905
- SMART Error Log Version: 1
- ATA Error Count: 140 (device log contains only the most recent five errors)
- CR = Command Register [HEX]
- FR = Features Register [HEX]
- SC = Sector Count Register [HEX]
- SN = Sector Number Register [HEX]
- CL = Cylinder Low Register [HEX]
- CH = Cylinder High Register [HEX]
- DH = Device/Head Register [HEX]
- DC = Device Command Register [HEX]
- ER = Error register [HEX]
- ST = Status register [HEX]
- Powered_Up_Time is measured from power on, and printed as
- DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
- SS=sec, and sss=millisec. It "wraps" after 49.710 days.
- Error 140 occurred at disk power-on lifetime: 27722 hours (1155 days + 2 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 65 ff ff ff 4f 00 12d+00:25:24.012 READ FPDMA QUEUED
- 60 00 00 ff ff ff 4f 00 12d+00:25:22.815 READ FPDMA QUEUED
- 60 00 40 ff ff ff 4f 00 12d+00:25:22.781 READ FPDMA QUEUED
- 60 00 40 ff ff ff 4f 00 12d+00:25:22.781 READ FPDMA QUEUED
- 60 00 00 ff ff ff 4f 00 12d+00:25:22.781 READ FPDMA QUEUED
- Error 139 occurred at disk power-on lifetime: 27408 hours (1142 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 a0 ff ff ff 4f 00 48d+15:21:33.395 READ FPDMA QUEUED
- 60 00 c0 ff ff ff 4f 00 48d+15:21:33.395 READ FPDMA QUEUED
- 60 00 20 ff ff ff 4f 00 48d+15:21:33.395 READ FPDMA QUEUED
- 60 00 e0 ff ff ff 4f 00 48d+15:21:33.395 READ FPDMA QUEUED
- 60 00 20 ff ff ff 4f 00 48d+15:21:33.395 READ FPDMA QUEUED
- Error 138 occurred at disk power-on lifetime: 27408 hours (1142 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 60 ff ff ff 4f 00 48d+15:21:19.536 READ FPDMA QUEUED
- 60 00 10 ff ff ff 4f 00 48d+15:21:19.535 READ FPDMA QUEUED
- 60 00 00 ff ff ff 4f 00 48d+15:21:19.535 READ FPDMA QUEUED
- 60 00 e7 ff ff ff 4f 00 48d+15:21:19.535 READ FPDMA QUEUED
- 60 00 00 ff ff ff 4f 00 48d+15:21:19.535 READ FPDMA QUEUED
- Error 137 occurred at disk power-on lifetime: 27408 hours (1142 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 20 ff ff ff 4f 00 48d+15:20:18.916 READ FPDMA QUEUED
- 60 00 80 ff ff ff 4f 00 48d+15:20:18.916 READ FPDMA QUEUED
- 60 00 a1 ff ff ff 4f 00 48d+15:20:18.916 READ FPDMA QUEUED
- 60 00 20 ff ff ff 4f 00 48d+15:20:18.916 READ FPDMA QUEUED
- 60 00 c2 ff ff ff 4f 00 48d+15:20:18.916 READ FPDMA QUEUED
- Error 136 occurred at disk power-on lifetime: 27408 hours (1142 days + 0 hours)
- When the command that caused the error occurred, the device was active or idle.
- After command completion occurred, registers were:
- ER ST SC SN CL CH DH
- -- -- -- -- -- -- --
- 40 53 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
- Commands leading to the command that caused the error were:
- CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
- -- -- -- -- -- -- -- -- ---------------- --------------------
- 60 00 01 ff ff ff 4f 00 48d+15:19:49.988 READ FPDMA QUEUED
- 60 00 61 ff ff ff 4f 00 48d+15:19:49.987 READ FPDMA QUEUED
- 60 00 e1 ff ff ff 4f 00 48d+15:19:49.987 READ FPDMA QUEUED
- 60 00 60 ff ff ff 4f 00 48d+15:19:49.987 READ FPDMA QUEUED
- 60 00 40 ff ff ff 4f 00 48d+15:19:49.987 READ FPDMA QUEUED
- SMART Self-test log structure revision number 1
- No self-tests have been logged. [To run self-tests, use: smartctl -t]
- SMART Selective self-test log data structure revision number 1
- SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
- 1 0 0 Not_testing
- 2 0 0 Not_testing
- 3 0 0 Not_testing
- 4 0 0 Not_testing
- 5 0 0 Not_testing
- Selective self-test flags (0x0):
- After scanning selected spans, do NOT read-scan remainder of disk.
- If Selective self-test is pending on power-up, resume after 0 minute delay.
Advertisement
Add Comment
Please, Sign In to add comment