PRELOADER.3.2.0.REL_R2787.w11
DD: efuse2: 00006070 => 55e7 => 0x01c4; 00000060 => 0xbcc8... done
DD: efuse3: 00000505 => 0xbcc4... done
DD: efuse4: 00008999 => 0xbcdc... done
DD: efuse5: 0000aaaa => 0xbce0... done
DD: efuse6: di: a1; sds_num: 0; gphy_num: 0
DD: efuse gphy: done
DD: efuse sds: done
DD: efuse lxb: break
II: Disabling OCP/LX timeout monitors... done
Get prestate = 1 in the init stage...
II: NOR SPI-F... Generic 3B NOR SPI-F [00ef4018] selected... done
II: OCP 100MHz(400/P4/C1), MEM 325MHz, LX 200MHz, SPIF 50MHz(1000/(5*4))

DRAM AUTO CALIBRATION
AutoK: ZQ Calibration Passed
AutoK: MR0: 0x00100b62
AutoK: MR1: 0x00110040
AutoK: MR2: 0x00120000
AutoK: MR3: 0x00130000
bit:00, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb8001510) = 0x1e0f00
bit:01, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001514) = 0x1e1102
bit:02, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001518) = 0x1e1102
bit:03, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb800151c) = 0x1e1102
bit:04, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001520) = 0x1e1102
bit:05, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001524) = 0x1e1102
bit:06, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb8001528) = 0x1e0f00
bit:07, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb800152c) = 0x1e0f00
bit:08, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001530) = 0x1e1102
bit:09, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb8001534) = 0x1e0f00
bit:10, max_w_s(00), max_w_len(19), max_r_s(00), max_r_len(31): (0xb8001538) = 0x1e0f00
bit:11, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb800153c) = 0x1e1102
bit:12, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001540) = 0x1e1102
bit:13, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001544) = 0x1e1102
bit:14, max_w_s(00), max_w_len(21), max_r_s(02), max_r_len(29): (0xb8001548) = 0x1e1102
bit:15, max_w_s(00), max_w_len(21), max_r_s(00), max_r_len(31): (0xb800154c) = 0x1e0f00
bit:16, max_w_s(00), max_w_len(17), max_r_s(02), max_r_len(29): (0xb8001550) = 0x1e1102
bit:17, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001554) = 0x1e1102
bit:18, max_w_s(00), max_w_len(17), max_r_s(04), max_r_len(27): (0xb8001558) = 0x1e1304
bit:19, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb800155c) = 0x1e1102
bit:20, max_w_s(00), max_w_len(19), max_r_s(04), max_r_len(27): (0xb8001560) = 0x1e1304
bit:21, max_w_s(00), max_w_len(17), max_r_s(02), max_r_len(29): (0xb8001564) = 0x1e1102
bit:22, max_w_s(00), max_w_len(19), max_r_s(00), max_r_len(31): (0xb8001568) = 0x1e0f00
bit:23, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb800156c) = 0x1e1102
bit:24, max_w_s(00), max_w_len(17), max_r_s(02), max_r_len(29): (0xb8001570) = 0x1e1102
bit:25, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001574) = 0x1e1102
bit:26, max_w_s(00), max_w_len(17), max_r_s(00), max_r_len(31): (0xb8001578) = 0x1e0f00
bit:27, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb800157c) = 0x1e1102
bit:28, max_w_s(00), max_w_len(19), max_r_s(02), max_r_len(29): (0xb8001580) = 0x1e1102
bit:29, max_w_s(00), max_w_len(17), max_r_s(02), max_r_len(29): (0xb8001584) = 0x1e1102
bit:30, max_w_s(00), max_w_len(19), max_r_s(04), max_r_len(27): (0xb8001588) = 0x1e1304
bit:31, max_w_s(00), max_w_len(17), max_r_s(00), max_r_len(31): (0xb800158c) = 0x1e0f00
AutoK: dram auto calibrtaion is done

II: MEM_PROBE_OK
II: MEM_XLAT_OK
II: MEM_TO_REG_OK
II: MEM_CNTLR_ZQ_STRICT_OK
II: MEM_CAL_OK
II: cntlr zq result: 0018e975
II: dcr result: 11210000
II: Decompressing U-Boot (0x80f00000 <- 0x9fc1a200)... (212 KB <- 80 KB) OK
II: Starting U-boot...

CIG Version: 3.04.09

U-Boot 2011.12.NA-svn94986 (Jan 15 2016 - 17:00:30)

Board: RTL9601B CPU:100MHz LX:200MHz DDR2:325MHz..
SPI-F: 1x16 MB (plr_flash_info @ 9f002d20)
[debug] start to init flash_info (1)
[debug] <0> unit size=0x10000, unit count=256
*** Warning - bad CRC, using default environment

*** !!! Check Result: Chk_CRC: 0x0, Chk_Empty: 0x0
Net:   LUNA GMAC
Warning: eth device name has a space!

**************************************
*                                    *
*  KEY -- Enter console terminal     *
*                                    *
**************************************
waiting for your select .....
do_jffs2_fsload offset 0x80400000 loadaddr=0xbd088000..
get loadbit 0,bootbit 0
Get current Image = ImageA..

--- jffs2_part_info: partition number 2 for device sflash0 (sflash.0)

Loading 'uImage' from  CRAMFS Partition 'imagea' to 0x80400000.

Root Filesystem crc check successfully!


PRODUCT:  sfu
SS  :  noss
DSP :  nodsp
WIFI:  nowifi
XDSL:  nodsl
Software version:  3FE45655AOCK31
## Booting kernel from Legacy Image at 80400000 ...
   Image Name:   Linux Kernel Image
   Created:      2015-12-11   6:28:09 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1440099 Bytes = 1.4 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.30.9-cig-sfu-1 (taojipeng@sw1-dev) (gcc version 4.4.6 (Realtek RSDK-1.5.6p2) ) #1 Fri Dec 11 11:48:11 CST 2015
CPU revision is: 0000dc02
Determined physical RAM map:
 memory: 03800000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 01f00000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001f00
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 7874
Kernel command line: console=ttyS0,115200 mem=31M root=/dev/mtdblock2 mtdparts=sflash:512K@0x0(Boot),0x180000@0x80000(Config),7M@0x200000(ImageA),7M@0x900000(ImageB) rootfstype=cramfs hasEeprom=0 5srst=0
root_dev_setup line 179 root: /dev/mtdblock2
icache: 64kB/32B, dcache: 32kB/32B, scache: 0kB/0B
NR_IRQS:128
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28056k/31744k available (2448k kernel code, 3688k reserved, 653k data, 108k init, 0k highmem)
Calibrating delay loop... 97.79 BogoMIPS (lpj=48896)
Mount-cache hash table entries: 512
IMEM section size = 0x3244
net_namespace: 788 bytes
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
Realtek GPIO Driver for Flash Reload Default
netlog: listening on port 4660
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 54
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 49) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
===============================================================================
init_luna_nor_spi_map: flash map at 0xbd000000
luna spi probe...
luna SPI FLASH G2 driver version 1.00-II: NOR SPI-F... Generic 3B NOR SPI-F detected... done
master->name sflash
cmd: cmdlinepart
4 cmdlinepart partitions found on MTD device sflash
add luna nor spi partition
MTD partitions obtained from kernel command line
Creating 4 MTD partitions on "sflash":
0x000000000000-0x000000080000 : "Boot"
0x000000080000-0x000000200000 : "Config"
0x000000200000-0x000000900000 : "ImageA"
0x000000900000-0x000001000000 : "ImageB"
===============================================================================
u32 classifier
nf_conntrack version 0.5.0 (496 buckets, 1984 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Realtek SD2-FastPath v1.00beta_2.4.26-uc0
/proc/FastPath created
Realtek MCast FastPath
/proc/mc_FastPath created
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
VFS: Mounted root (cramfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 108k freed

# num is 10,nothing need to do
ONT>Starting Application: 0x00002000, /bin/TimerMgr................Done.
Starting Application: 0x00001000, /bin/LogMgr................Done.
app 0x00007000 stop invalid timer[0]
### Invalid Decimal_Factor, use default 0xdb
### Invalid Settle_Time, use default 0x68
### Invalid P1_Mask, use default 0x5a
### Invalid P0_Mask, use default 0x8
Tx has been calibrated!!
Starting Application: 0x00007000, /bin/MiscMgr................Done.
Check base image file CRC ... cal_crc (706307a4) ori_crc (706307a4) Success.
Mount Backup[/dev/mtdblock3] as cramfs...Success.
major ID[0xa9] minor ID[0x1]
cp: can't stat '/mnt/rwdir2/sys.log': No such file or directory
mv: can't create '/mnt/rwdir2/sys.log': Read-only file system
cp: can't stat '/mnt/rwdir2/sys.log': No such file or directory
mv: can't create '/mnt/rwdir2/sys.log': Read-only file system
Starting Application: 0x00003000, /bin/MecMgr................Done.
Starting Application: 0x00004000, /bin/PonMgr................Done.
------>NET open default xml failedStarting Application: 0x00009000, /bin/NetMgr................Done.
Starting Application: 0x00005000, /bin/EthMgr................Done.
Starting Application: 0x0000c000, /bin/WebMgr................Done.
Laser TX OFF
Laser TX ON
Preparing stress ...

INFO: ALL APPs are ready.
ONT>ls
ONT>
ONT>cd /
ONT>