Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- GXBB:BL1:08dafd:0a8993;FEAT:EDFD718C;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;
- no sdio debug board detected
- TE: 69250
- BL2 Built : 15:22:26, Nov 13 2015.
- gxb g6dcf28d - xiaobo.gu@droid05
- Board Ver is 1
- rn5t567_power_init
- Board ID = 8
- CPU clk: 1536MHz
- DDR channel setting: DDR0 Rank0+1 same
- DDR0: 1024MB @ 912MHz(2T)-13
- DataBus test pass!
- AddrBus test pass!
- Load fip header from eMMC, src: 0x0000c000, des: 0x01400000, size: 0x000000b0
- Load bl30 from eMMC, src: 0x00010000, des: 0x01000000, size: 0x00009e70
- Sending bl30........................................OK.
- Run bl30...
- Load bl301 from eMMC, src: 0x0001c000, des: 0x01000000, size: 0x00001ce0
- Wait bl30...Done
- Sending bl301........OK.
- Run bl301...
- src: 0x00020000, des: 0x10100000, size: 0x00011130
- --- UART initialized after reboot ---
- [Reset cause: unknown]
- [Image: unknown, amlogic_v1.1.3043-8623ae6 2015-09-16 16:38:21 jianxin.pan@droid06]
- bl30: check_permit, count is 1
- bl30: check_permit: ok!
- chipidLoad bl33 from eMMC, src: 0x00034000, des: 0x01000000, size: 0x00075c10
- : ef be ad de d f0 ad ba ef be ad de not ES chip
- [0.219471 Inits done]
- secure task start!
- high task start!
- low task start!
- NOTICE: BL3-1: v1.0(debug):4621162
- NOTICE: BL3-1: Built : 13:57:23, Nov 10 2015
- INFO: BL3-1: Initializing runtime services
- INFO: BL3-1: Preparing for EL3 exit to normal world
- INFO: BL3-1: Next image address = 0x1000000
- INFO: BL3-1: Next image spsr = 0x3c9
- U-Boot 2015.01-gf208d9f (Apr 27 2016 - 17:07:09)
- DRAM: 1 GiB
- Relocation Offset is: 36eff000
- register usb cfg[0][1] = 0000000037f66de0
- vpu detect type: 5
- vpu clk_level = 7
- set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
- MMC: aml_priv->desc_buf = 0x0000000033eef6d0
- aml_priv->desc_buf = 0x0000000033ef1860
- SDIO Port B: 0, SDIO Port C: 1
- [mmc_init] mmc init success
- mmc read lba=0x4000, blocks=0x400
- Amlogic multi-dtb tool
- Multi dtb detected
- Multi dtb tool version: v2 .
- Support 2 dtbs.
- aml_dt soc: gxbb platform: jp variant: 6
- dtb 0 soc: gxbb plat: jp vari: 0
- dtb 1 soc: gxbb plat: jp vari: 6
- Find match dtb: 1
- start dts,buffer=0000000033ef3cf0,dt_addr=0000000033efbcf0
- parts: 10
- 00: cache 0000000010000000 2
- 01: logo 0000000000400000 1
- 02: recovery 0000000002000000 1
- 03: misc 0000000002000000 1
- 04: boot 0000000001400000 1
- 05: system 0000000040000000 1
- 06: backup 0000000020000000 4
- 07: persist 0000000000800000 4
- 08: panic 0000000000400000 4
- 09: data ffffffffffffffff 4
- get_dtb_struct: Get emmc dtb OK!
- [mmc_get_partition_table] skip cache partition.
- Partition table get from SPL is :
- name offset size flag
- ===================================================================================
- 0: bootloader 0 400000 0
- 1: reserved 400000 800000 0
- 2: cache c00000 10000000 2
- 3: env 10c00000 400000 0
- 4: logo 11000000 400000 1
- 5: recovery 11400000 2000000 1
- 6: misc 13400000 2000000 1
- 7: boot 15400000 1400000 1
- 8: system 16800000 40000000 1
- 9: backup 56800000 20000000 4
- 10: persist 76800000 800000 4
- 11: panic 77000000 400000 4
- 12: data 77400000 74c00000 4
- mmc read lba=0x2000, blocks=0x1
- mmc read lba=0x2001, blocks=0x1
- mmc_read_partition_tbl: mmc read partition OK!
- eMMC/TSD partition table have been checked OK!
- mmc env offset: 0x10c00000
- In: serial
- Out: serial
- Err: serial
- Boot command:
- Boot status:
- Boot message
- ""
- upgrade_step=0
- dtbLoadaddr = 0x0000000001000000
- amlkey_init() enter!
- [EFUSE_MSG]keynum is 4
- hpd_state=0
- [CANVAS]addr=0x3f800000 width=5760, height=2160
- [1080p60hz] is invalid for cvbs.
- set hdmitx VIC = 16
- config HPLL = 2970
- HPLL: 0xc800023d
- config HPLL done
- set_hpll_od3_clk_div[216] div = 6
- j = 8 vid_clk_div = 1
- hdmitx phy setting done
- hdmitx: set enc for VIC: 16
- enc_vpu_bridge_reset[977]
- reboot_mode=normal
- pull down bt_reset
- pull up bt_reset
- set hci reset
- set scan parameters
- 04 10 01 00
- set scan enable
- 04 10 01 00
- 04 10 01 00
- 04 10 01 00
- IR init done!
- Hit any key to stop autoboot: 0
- (Re)start USB...
- USB0: dwc_usb driver version: 2.94 6-June-2012
- USB (0) peri reg base: c0000000
- USB (0) use clock source: XTAL input, div: 1
- USB (0) base addr: 0xc9000000
- Force id mode: Host
- dwc_otg: Highspeed device found !
- scanning bus 0 for devices... 1 USB Device(s) found
- scanning usb for storage devices... 1 Storage Device(s) found
- reading s905_autoscript
- 699 bytes read in 26 ms (25.4 KiB/s)
- ## Executing script at 01020000
- ########## cmd=setenv env_addr 0x1040000
- setenv boot_start 'bootm ${loadaddr} - ${dtb_mem_addr}'
- setenv addmac 'if printenv mac; then setenv bootargs ${bootargs} mac=${mac}; elif printenv eth_mac; then setenv bootargs ${bootargs} mac=${eth_mac}; fi'
- setenv try_boot_start 'if fatload ${devtype} ${devnum} ${loadaddr} KERNEL; then fatload ${devtype} ${devnum} ${env_addr} uEnv.ini && env import -t ${env_addr} ${filesize} && run addmac; fatload ${devtype} ${devnum} ${dtb_mem_addr} ${dtb_name} && run boot_start; fi'
- setenv devtype mmc
- setenv devnum 0
- run try_boot_start
- setenv devtype usb
- for devnum in 0 1 2 3 ; do run try_boot_start ; done
- ** Bad device mmc 0 **
- reading KERNEL
- 11363340 bytes read in 11988 ms (924.8 KiB/s)
- reading uEnv.ini
- 182 bytes read in 19 ms (8.8 KiB/s)
- ## Error: "mac" not defined
- ## Error: "eth_mac" not defined
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- reading KERNEL
- 11363340 bytes read in 11987 ms (924.8 KiB/s)
- reading uEnv.ini
- 182 bytes read in 19 ms (8.8 KiB/s)
- ## Error: "mac" not defined
- ## Error: "eth_mac" not defined
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- reading KERNEL
- 11363340 bytes read in 11987 ms (924.8 KiB/s)
- reading uEnv.ini
- 182 bytes read in 19 ms (8.8 KiB/s)
- ## Error: "mac" not defined
- ## Error: "eth_mac" not defined
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- reading KERNEL
- 11363340 bytes read in 11988 ms (924.8 KiB/s)
- reading uEnv.ini
- 182 bytes read in 19 ms (8.8 KiB/s)
- ## Error: "mac" not defined
- ## Error: "eth_mac" not defined
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- ** Bad device usb 1 **
- ** Bad device usb 2 **
- ** Bad device usb 3 **
- ## Error: "storeboot" not defined
- JurassicPark#reset
- resetting ...
- GXBB:BL1:08dafd:0a8993;FEAT:EDFD718C;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;
- no sdio debug board detected
- TE: 57089
- BL2 Built : 15:22:26, Nov 13 2015.
- gxb g6dcf28d - xiaobo.gu@droid05
- Board Ver is 1
- rn5t567_power_init
- Board ID = 8
- CPU clk: 1536MHz
- DDR channel setting: DDR0 Rank0+1 same
- DDR0: 1024MB @ 912MHz(2T)-13
- DataBus test pass!
- AddrBus test pass!
- Load fip header from eMMC, src: 0x0000c000, des: 0x01400000, size: 0x000000b0
- Load bl30 from eMMC, src: 0x00010000, des: 0x01000000, size: 0x00009e70
- Sending bl30........................................OK.
- Run bl30...
- Load bl301 from eMMC, src: 0x0001c000, des: 0x01000000, size: 0x00001ce0
- Wait bl30...Done
- Sending bl301........OK.
- Run bl301...
- MC, src: 0x00020000, des: 0x10100000, size: 0x00011130
- --- UART initialized after reboot ---
- [Reset cause: unknown]
- [Image: unknown, amlogic_v1.1.3043-8623ae6 2015-09-16 16:38:21 jianxin.pan@droid06]
- bl30: check_permit, count is 1
- bl30: check_permit: ok!
- chipidLoad bl33 from eMMC, src: 0x00034000, des: 0x01000000, size: 0x00075c10
- : ef be ad de d f0 ad ba ef be ad de not ES chip
- [0.207396 Inits done]
- secure task start!
- high task start!
- low task start!
- NOTICE: BL3-1: v1.0(debug):4621162
- NOTICE: BL3-1: Built : 13:57:23, Nov 10 2015
- INFO: BL3-1: Initializing runtime services
- INFO: BL3-1: Preparing for EL3 exit to normal world
- INFO: BL3-1: Next image address = 0x1000000
- INFO: BL3-1: Next image spsr = 0x3c9
- U-Boot 2015.01-gf208d9f (Apr 27 2016 - 17:07:09)
- DRAM: 1 GiB
- Relocation Offset is: 36eff000
- register usb cfg[0][1] = 0000000037f66de0
- vpu detect type: 5
- vpu clk_level = 7
- set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)
- MMC: aml_priv->desc_buf = 0x0000000033eef6d0
- aml_priv->desc_buf = 0x0000000033ef1860
- SDIO Port B: 0, SDIO Port C: 1
- [mmc_init] mmc init success
- mmc read lba=0x4000, blocks=0x400
- Amlogic multi-dtb tool
- Multi dtb detected
- Multi dtb tool version: v2 .
- Support 2 dtbs.
- aml_dt soc: gxbb platform: jp variant: 6
- dtb 0 soc: gxbb plat: jp vari: 0
- dtb 1 soc: gxbb plat: jp vari: 6
- Find match dtb: 1
- start dts,buffer=0000000033ef3cf0,dt_addr=0000000033efbcf0
- parts: 10
- 00: cache 0000000010000000 2
- 01: logo 0000000000400000 1
- 02: recovery 0000000002000000 1
- 03: misc 0000000002000000 1
- 04: boot 0000000001400000 1
- 05: system 0000000040000000 1
- 06: backup 0000000020000000 4
- 07: persist 0000000000800000 4
- 08: panic 0000000000400000 4
- 09: data ffffffffffffffff 4
- get_dtb_struct: Get emmc dtb OK!
- [mmc_get_partition_table] skip cache partition.
- Partition table get from SPL is :
- name offset size flag
- ===================================================================================
- 0: bootloader 0 400000 0
- 1: reserved 400000 800000 0
- 2: cache c00000 10000000 2
- 3: env 10c00000 400000 0
- 4: logo 11000000 400000 1
- 5: recovery 11400000 2000000 1
- 6: misc 13400000 2000000 1
- 7: boot 15400000 1400000 1
- 8: system 16800000 40000000 1
- 9: backup 56800000 20000000 4
- 10: persist 76800000 800000 4
- 11: panic 77000000 400000 4
- 12: data 77400000 74c00000 4
- mmc read lba=0x2000, blocks=0x1
- mmc read lba=0x2001, blocks=0x1
- mmc_read_partition_tbl: mmc read partition OK!
- eMMC/TSD partition table have been checked OK!
- mmc env offset: 0x10c00000
- In: serial
- Out: serial
- Err: serial
- Boot command:
- Boot status:
- Boot message
- ""
- upgrade_step=0
- dtbLoadaddr = 0x0000000001000000
- amlkey_init() enter!
- [EFUSE_MSG]keynum is 4
- hpd_state=0
- [CANVAS]addr=0x3f800000 width=5760, height=2160
- [1080p60hz] is invalid for cvbs.
- set hdmitx VIC = 16
- config HPLL = 2970
- HPLL: 0xc800023d
- config HPLL done
- set_hpll_od3_clk_div[216] div = 6
- j = 8 vid_clk_div = 1
- hdmitx phy setting done
- hdmitx: set enc for VIC: 16
- enc_vpu_bridge_reset[977]
- reboot_mode=normal
- pull down bt_reset
- pull up bt_reset
- set hci reset
- set scan parameters
- 04 10 01 00
- set scan enable
- 04 10 01 00
- 04 10 01 00
- 04 10 01 00
- IR init done!
- Hit any key to stop autoboot: 0
- (Re)start USB...
- USB0: dwc_usb driver version: 2.94 6-June-2012
- USB (0) peri reg base: c0000000
- USB (0) use clock source: XTAL input, div: 1
- USB (0) base addr: 0xc9000000
- Force id mode: Host
- dwc_otg: Highspeed device found !
- scanning bus 0 for devices... 1 USB Device(s) found
- scanning usb for storage devices... 1 Storage Device(s) found
- reading s905_autoscript
- 699 bytes read in 25 ms (26.4 KiB/s)
- ## Executing script at 01020000
- ########## cmd=setenv env_addr 0x1040000
- setenv boot_start 'bootm ${loadaddr} - ${dtb_mem_addr}'
- setenv addmac 'if printenv mac; then setenv bootargs ${bootargs} mac=${mac}; elif printenv eth_mac; then setenv bootargs ${bootargs} mac=${eth_mac}; fi'
- setenv try_boot_start 'if fatload ${devtype} ${devnum} ${loadaddr} KERNEL; then fatload ${devtype} ${devnum} ${env_addr} uEnv.ini && env import -t ${env_addr} ${filesize} && run addmac; fatload ${devtype} ${devnum} ${dtb_mem_addr} ${dtb_name} && run boot_start; fi'
- setenv devtype mmc
- setenv devnum 0
- run try_boot_start
- setenv devtype usb
- for devnum in 0 1 2 3 ; do run try_boot_start ; done
- ** Bad device mmc 0 **
- reading KERNEL
- 11363340 bytes read in 11987 ms (924.8 KiB/s)
- reading uEnv.ini
- 182 bytes read in 19 ms (8.8 KiB/s)
- ## Error: "mac" not defined
- ## Error: "eth_mac" not defined
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- reading KERNEL
- 11363340 bytes read in 11986 ms (925.8 KiB/s)
- reading uEnv.ini
- 182 bytes read in 19 ms (8.8 KiB/s)
- ## Error: "mac" not defined
- ## Error: "eth_mac" not defined
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- reading KERNEL
- 11363340 bytes read in 11986 ms (925.8 KiB/s)
- reading uEnv.ini
- 182 bytes read in 19 ms (8.8 KiB/s)
- ## Error: "mac" not defined
- ## Error: "eth_mac" not defined
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- reading KERNEL
- 11363340 bytes read in 11987 ms (924.8 KiB/s)
- reading uEnv.ini
- 182 bytes read in 19 ms (8.8 KiB/s)
- ## Error: "mac" not defined
- ## Error: "eth_mac" not defined
- fatload - load binary file from a dos filesystem
- Usage:
- fatload <interface> [<dev[:part]> [<addr> [<filename> [bytes [pos]]]]]
- - Load binary file 'filename' from 'dev' on 'interface'
- to address 'addr' from dos filesystem.
- 'pos' gives the file position to start loading from.
- If 'pos' is omitted, 0 is used. 'pos' requires 'bytes'.
- 'bytes' gives the size to load. If 'bytes' is 0 or omitted,
- the load stops on end of file.
- If either 'pos' or 'bytes' are not aligned to
- ARCH_DMA_MINALIGN then a misaligned buffer warning will
- be printed and performance will suffer for the load.
- ** Bad device usb 1 **
- ** Bad device usb 2 **
- ** Bad device usb 3 **
- ## Error: "storeboot" not defined
- JurassicPark#
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement