FUEL OIL SYSTEM OF THE NEW YORK

 	A	B	C
1	BOARD OF INSPECTION AND SURVEY
2 	Class: CG
3 	Inspection Deck:  Main Propulsion
4 	SYSTEM / EQUIPEMENT	EVENT NUMBER	Last Update
5
6	GTM	MP0100	1-Feb-12
7	GTG	MP0160	1-Feb-12
8	FUEL OIL SYSTEM	MP0120, MP0230	1-Feb-12
9	LO SYSTEM - CRP	MP0140, MP0220, MP0240	1-Feb-12
10	SHAFTING - RED GEARS	MP0030, MP0100	1-Feb-12
11	SMART SHIP CONTROLS	MP0120, MP0180, MP0190	1-Feb-12
12	CONTROLS	MP0180, MP0190	1-Feb-12
13	BLEED AIR SYSTEM	MP0100	1-Feb-12
14	WASTE HEAT SYSTEM	MP0150, MP0210	1-Feb-12
15	HULL	DC0380	1-Feb-12
16	UNDERWAY DEMONSTRATIONS	MP0070, MP0120, MP0130, MP0210	1-Feb-12
17
GTM

 	A	B	C	D	E	F
1	Class: CG
2	Inspection Deck: MP
3	Major System:  GTM
4	Procedure Description	Reference	Results	Results	Results	Results
5	Gas Turbine Engine and Module	MP0100	1A	1B	2A	2B
6	Inspect Gas Turbine Bellmouth Spray Pattern	2340/002 (R-11)
7	Inspect Inlet Plenum, Inlet Screen, and Inlet Duct and Centerbody	2340/002 (S-4R)
8	Inspect Bleed Air Manifold Assembly	2340/002 (R-16)
9	Inspect Ventilation Dampers for Leaks	2340/002 (R-17)
10	Inspect MFC VSV Feedback Lever and Actuation System	2340/002 (S-6R)
11	Inspect DFC, VSV, and Actuation System	2340/002 (S-5R)
12	Inspect Gas Turbine and Base Enclosure Interior	2340/002 (R-20)
13	Inspect Base Enclosure Exterior	2340/002 (R-20)
14	Inspect Module Floor Fluid Drains	2340/002 (R-23)
15	Inspect Welds on Exhaust Collector Fwd/Aft Lugs and Stiffeners	2340/002 (R-23)
16	Inspect Module Base Bonding/Grounding Straps	2340/002 (R-26)
17	Verify all technical directives have been installed	GTB “ZERO INDEX”
MGTSR/ WEBLOG
18	Inspect installed instruments	CRL, NSTM 504,JFMM
19	Gas Turbine Engine Intakes	MP0100
20	Inspect Propulsion Air Inlet System	2513/001 (S-11)
21	Inspect Blow-in Door Assembly	2513/001 (S-5)
22	Test Blow-in Doors Automatic Operation	2513/001 (S-5)
23	Gas Turbine Engine Uptakes	MP0100
24	Inspect  Exhaust assembly	2591/002 (A-1)
25	Gas Turbine Engine Fire Protection	MP0100
26	Test CO2 Rlease Inhibit switch	2521/005 (Q-5, S-16)
27	Test Fire Alarm Pushbutton	2521/005 (Q-5, S-16)
28	Test Fire Detection temperature switch	2521/005 (Q-5, S-16)
29	Test Flame Detector	2521/005 (Q-5, S-16)
30	Gas Turbine Engine Test/Idle Checks	MP0100
31	Conduct LP Motor	EOP CPTM
32	Conduct LP Air Start	EOP CMSI, PTOP
33	Conduct HP Air Start	EOP CMSI, PTOP
34	Conduct Idle Checks	EOP CMSI, PTOP
35	Test Operation of Fuel Shutdown Valves	2521/047 (R-1Q)
36	Gas Turbine Engine Special Tools	MP0100
37	Inspect and Inventory LM2500 Special Support and Equipment	2340/002 (R-25)
38	MAIN ENGINE CONTROL UNIT  (SMART SHIP)                 	MP0100
39	Test Main Engine Control Unit Primary/Backup Power Turbine Overspeed Trip	2521/040 R-5A
40 	Test Main Engine Control Unit Primary/Backup Power Turbine Tach Loss Trip	2521/040 R-5A
41 	Test Main Engine Control Unit Loss of Micronet Power Latch-Out Test	2521/040 R-5A
42 	Test Main Engine Control Unit Loss of Main Fuel Valve Power & Latch-Out Test	2521/040 R-5A
43
GTG

 	A	B	C	D	E
1	Class: CG
2 	Inspection Deck: MP
3 	Major System:  GTG
4 	Subsystem/Component: N/A
5 	Pre-Underway Checks/Demos:
6 	Procedure Description	Reference	Results	Results	Results
7	Gas Turbine Generator and Module	MP0160	1	2	3
8	Inspect Compressor Exterior	3113/008 (R-9)
9 	Inspect Accessory Gear Box	3113/008 (R-9)
10 	Inspect Governor and Piston Liquid Fuel Valve linkage.	3113/008 (R-9)
11 	Inspect Diffuser Case	3113/008 (R-9)
12 	Inspect Combustor	3113/008 (R-9)
13 	Inspect Turbine	3113/008 (R-9)
14 	Inspect Module	3113/008 (R-9)
15 	Inspect Exhaust Assembly	3113/008 (R-9)
16 	Inspect Reduction Gear Enclosure	EOP GTGI
3113/008 (R-9)
17 	Inspect GTG Seawater Pump Mechanical Seal	3431/001 (M-6)
18 	Inspect/flush  Seawater Cooling Strainers	3431/001 (Q-8)
19 	Inspect Module Mounts	3113/008 (24M-1)
GGTB 10 REV 1
20 	Inspect Engine Lube Oil Sump Levels	EOP GTSS
21 	Inspect GTG Flex Hoses	GGTB 6 REV 1
S6430-AE-TED-010
3113/008 (R-9)
22 	Inspect installed instruments	CRL, NSTM 504,JFMM
23 	Gas Turbine Generator Intakes	MP0160
24 	Inspect Intakes	3431/001 (S-11)
25 	Inspect and Lubricate Blow-in Panels	3431/001 (S-6)
26 	Test Blow in Doors Automatic Operation	3431/001 (S-6)
27 	Gas Turbine Generator Tests	MP0160
28 	Test SSGTG Alarms and Shutdowns.	3113/008 (R-22)
29 	Test SSGTG No Break Power Supply Batteries	3431/001 (A-6R)
30 	Test Enclosure Fire Detection and Protection Circuitry	3113/008 (R-22)
31 	Test Emergency Cooling Back up	LOP
32 	Gas Turbine Generator Idle Checks	MP0160
33 	Start GTG Verify all Start/Operating limits	EOP GTGMS
S9234-B3-MMO-010 Table 1-3
34
FUEL OIL SYSTEM

 	A	B	C	D
1	Class: CG
2 	Inspection Deck:  MP
3 	Major System:  Fuel Oil System
4 	Procedure Description	Reference	Results	Results
5	Fuel Oil Service System	MP0230	1	2
6	Inspect Flexible Hose Assemblies	5000/009 (S-1,A-1, A-2)
7 	Inspect Fuel Oil Service System	2610/005 (AP-4)
2610/005 (60M-2)
8 	Inspect Fuel Pump Mechanical Seal Pressurization System	EOP FOTG
9 	Inspect Fuel Oil Service Pump	NSTM 503
2610/005 (18M-1)
10 	Inspect Installed Instruments	CRL, NSTM 504
11 	Inspect Fuel Oil Service Heater	2610/005 (AP-5)
12 	Test Fuel Oil Pump Logic Sequencing Circuitry	2610/005 (A-21)
13 	Test Service Tank Suct/Recirc Valves	EOP FOTG
14 	Test Fuel Oil Service Tank Quick Closing Valves	5000/005 (A-2) LOP
15 	Test GTM Fuel Oil Solenoid Valves	EOP FOAS
16 	Test GTG/FO Head Tank Quick Closing Valves	5000/005 (A-2) LOP
17 	Test Fuel Oil Service Filter Separator DP Points	2610/005 (A-1)
18 	Test Fuel Oil Service Pre-Filter DP Points	2610/005 (A-2)
19 	Test FO Coalescer Interlock	Local procedure
20 	Fuel Oil Fill and Transfer	MP0120
21 	Inspect Flexible Hose Assemblies	5000/009 (S-1,A-1,A-2)
22 	Inspect Fuel Oil Transfer System	5410/014 (AP-8)
5410/014 (60M-1)
23 	Inspect Fuel Stripping/Expansion Tanks	NSTM 505/SNOK
24 	Inspect Fuel Oil Transfer Pump	NSTM 503
5410/014 (AP-7)
25 	Inspect Installed Instruments	CRL, NSTM 504
26 	Inspect Fuel Oil Transfer Heater	Local Procedure
27 	Test Motor Operated Valves	5000/005 (A-3)
28 	Test FSCC Alarms and Indicators	EOP CAF
29 	Test Local Fuel Control Console Alarms and Indicators	EOP CAF
30
LO SYSTEM - CRP

 	A	B	C	D
1	Class: CG
2 	Inspection Deck:  MP
3 	Major System:  Lube Oil System
4 	Procedure Description	Reference	Results	Results
5	Lube Oil System	MP0220	1	2
6	Inspect Flexible Hose Assemblies	5000/009 (S-1, A-1,A-2)
7 	Inspect Main Lube Oil System	2620/004 (AP-1)
8 	Inspect Main Lube Oil System Relief Valves	NSTM 505
2620/004 (60M-2)
9 	Inspect Main Lube Oil Service Pump	NSTM 503
2620/004 (AP-3)
10 	Inspect Attached Lube Oil Pump	NSTM 503
2620/004 (AP-5)
11 	Inspect Lube Oil  Pump Mechanical Seal Pressurization System	EOP LOSRG
12 	Test Main Lube Oil Pump Logic Sequencing	2620/004 (S-2)
13 	Test/Inspect Lube Oil Strainer	EOP LODS
14 	Test Lube Oil Strainer Differential Pressure Alarm	2620/004 (A-1)
15 	Inspect Installed Instruments	CRL, NSTM 504,JFMM
16 	Lube Oil Purifier	MP0140
17 	Inspect Installed Instruments	CRL, NSTM 504,JFMM
18 	Inspect Lube Oil Fill, Transfer and Purification System
- Piping/Hoses/Flange Shields
- Relief valve	NSTM 503
NSTM 505
2640/003 (AP-1)
19 	Inspect Lube Oil Purifier	2640/003 (AP-1)
20 	Inspect Purifier Oil Level	EOP LOPO
21 	Inspect Lube Oil Purifier Heater	EOP LOPO
22 	Inventory Lube Oil Purifier Special Tools	S9260-AD-MMA-010
23 	Test Lube Oil Purifier Operation	EOP LOPO
24 	Test Purifier Efficiency	NSTM 262
25 	CRP System	MP0240	1	2
26	Inspect CRP System	2451/005 (AP-1)
2451/005 (24M-2R)
27 	Inspect Flexible Hose Assemblies	NSTM 505
S6430-AE-TED-010
5000/009 (S-1, A-1,A-2)
28 	Inspect Hydraulic Fluid Sample for Contamination	2451/005 (R-1W)
29 	Inspect Installed Instruments	CRL, NSTM 504
30 	Inspect CRP Electric Pump and Mechanical Seal	NSTM 503
31 	Inspect CRP Attached Pump and Mechanical Seal	NSTM 503
32 	Inspect Attached and Electric Pump Suction Strainers	S9245-AV-MMA-010
33 	Drain BS&W from CRP Head Tank	2451/005 (R-4)
34 	Test and Adjust Mechanical Pitch Indicator	2451/005 (AP-1)
35 	Test Slew Rate	2451/005 (AP-1)
36 	Test Emergency Pitch Pump / Set Emergency Ahead Pitch	2451/005 (AP-1)
EOP SEAH
37 	Inspect Hydraulic Oil Level	S9245-AV-MMA-010
POG
38
SHAFTING - RED GEARS

 	A	B	C	D	E	F	G
1	Class: CG
2 	Inspection Deck:  MP
3 	Major System:  Shafting
4 	Procedure Description	Reference	Results	Results	Results	Results	Results
5	Line Shaft Bearing	MP0100	1A	2A	2B	2C	2D
6	Inspect Installed Instruments.	CRL, NSTM 504
7 	Inspect Line Shaft Bearing	NSTM 244
8 	Inspect Physical Security	CNSF 3540.3
9 	Inspect Depth Mic Surface and Bearing Constant	NSTM 244
10 	Inspect Sump Drain Valve Locking Device	CNSF 3540.3
11 	Inspect Sump Drain Valve Anti-Rotation Device	CNSF 3540.3
12 	Inspect Oil Level	2000/001 (R-1)
13 	Inspect Lube Oil Sample	2000/001 (R-1)
14 	Inspect Spare Line Shaft Bearing	NSTM 244
15 	Bulkhead Shaft Seal	MP0100	220	260	300	346
16 	Inspect Bulkhead Shaft Seal	S9243-BU-MMA-010
17 	Stern Tube Seal	MP0030	PORT	STBD
18 	Inspect Stern Tube Seal	S9243-A6-MMA-010, NSTM 244
19 	Inspect Installed Instruments	CRL, NSTM 504,JFMM
20 	Inspect Piping System, Hoses, Fittings	NSTM 505, 5000/009 (A-2), S6430-AE-TED-010
21 	Inspect/Shift Cooling Water Strainer/Filter	EOP STCW, 5000/015 (A-1, A-2, A-7)
22 	Inspect Emergency Packing Kit	S9243-A6-MMA-010
23 	Test Cooling Water Low Flow Alarm	2400/018 (S-1, S-2, S-3, S-4)
24 	Test Inflatable Seal	2400/018 (S-5)
25 	Reduction Gear	MP0100	PORT	STBD
26 	Inspect Reduction Gear	2411/023 (A-2)
27 	Inspect Security Devices	NSTM 241, CNSF 3540.3
28 	Inspect Installed Instruments	CRL, NSTM 504,JFMM
29 	Sample Lube Oil	2000/001 (R-1)
30 	Inspect Oil Level	EOP MUFP
31 	Inspect Vent Fog Precipitator	6650/002 (A-2)
32 	Test Dehumidifier Air Flow	2411/023 R-1W
33 	Inspect SFI’s for Proper Flow	2411/023 (R-2W)
34 	Inspect Turbine Brake Oil Level in Lubricator	2421/002 (U-1)
35 	Test GTM PT Brake	EOP CMSI
36 	Test Shaft Locking Mechanism	EOP LUSU
37 	Inspect Thrust Bearing	NSTM 244
38
SMART SHIP CONTROLS

 	A	B	C	D	E	F
1	Class: CG
2 	Inspection Deck:  MP
3 	Major System:  Controls
4 	Procedure Description	Reference	Results
5 	CENTRAL CONTROL STATION AND SMARTSHIP	MP0190
6 	Perform Intergrated Ship Control (ISC) System Inspection (shipset #1-8, #9AF)	2521/047, AP-1
7 	MECU (SMART SHIP) DIGI FUEL CNTRL GTM USE MRC A-3	MP0190	MER 1	MER 2
8	Power Turbine Speed Limiting	2521/047 A-3
9 	Power Turbine Overspeed Trip	2521/047 A-3
10 	Power Turbine Underspeed Shutdown Set Point	2521/047 A-3
11 	Loss of Micronet Power Latch-Out Test	2521/047 A-3
12 	Loss of Main Fuel Valve Power & Latch-Out	2521/047 A-3
13 	SMARTSHIP (check from any CCS console)	MP0190
14 	Shift to Propulsion Backup LAN	LOP
15 	Conduct CPU rollover test	MLOC
16 	Verify BIT faults	ECSE TECHMAN
17 	Verify history faults	ECSE TECHMAN
18 	Verify ATM/Network cabinet faults	ECSE TECHMAN
19 	Verify console temperatures	ECSE TECHMAN
20 	Verify DAU faults	ECSE TECHMAN
21 	Verify I/O faults	ECSE TECHMAN
22 	Verify DAE faults (2-8)	ECSE TECHMAN
23 	Verify password and login method	ECSE TECHMAN
24 	Verify rate of rise settings	MLOC
25 	Verify ETHOR settings	ECSE TECHMAN
26 	Verify Bell logging on	ECSE TECHMAN
27 	Verify pitch settings	MP0190
28 	Verify Standard orders set at 0	ECSE TECHMAN
29 	Ahead pitch set at 104%	ECSE TECHMAN
30 	Astern pitch set at -50%	ECSE TECHMAN
31 	DIGITAL SYNCH AND LOAD CONTROL	MP0190
32 	Inspect mechanical relay 4, 5, 6 (DSLC 1, 2, 3)	ECSE TECHMAN
33 	Ensure mode control switch in normal	ECSE TECHMAN
34 	Verify operating parameters	ECSE TECHMAN
35 	ESCE UPS	MP0190
36 	Test ECSE UPS	2521/047 A-2R
37 	FUEL OIL CONSOLE (SOSU) FUNCTION	MP0120
38 	Alarm/Lamp Test, Inspect	CAF
39 	Operate F/O Transfer Valves	LOP
40 	Test FOF-5	LOP, 2521/047 R-2
41 	ICAS	MP0180
42 	Inspect Computer Internal Shocks and Fans	2020/001 (M-3)
43 	Inspect all Cabinet Air Filters	2020/001 (M-3)
44 	Test ICAS Workstation UPS	2020/001 (S-1)
45 	Perform Operational Test	2020/001 (AP-2)
46 	Inspect overall compliance with reporting / IPARS, etc.
47
CONTROLS

 	A	B	C
1	Class: CG
2 	Inspection Deck:  MP
3 	Major System:  Controls
4 	Procedure Description	Reference	Results
5	Controls	MP0190
6 	Inspect PACC instruments	CRL
7 	Inspect PLCC instruments	CRL
8 	Inspect Torsionmeter	CRL
9 	Inspect and Test Bell/Data Logger	2521/005 (Q-1)
10 	Inspect PLCEE, S/CE, FSEE, PACEE and CISE Air Filters	2521/005 (S-1,2,3,6,7,8)
11 	Inspect PACEE, CISE, SCEEE, and PACC	2521/005 (18M)
12 	Test PACC/PLCC Alarms and Indicators	EOP CTAI
13 	Test Emergency Power on PACC, EPCC, CISE, PAMCE, PLCEE, and S/CE	2521/005 (R-2), 2521/006 (R-1)
14 	Test EPCC Self  Logic Test	EOP EPCT
15 	Test CISE	EOP CISE
16 	Test Overspeed Trip	EOP COT
17 	Test Propeller Pitch Control	EOP CPPT
18 	Test EPCC Alarms and Indicators	EOP EPCT
19 	Conduct EPCC Long Test	EOP EPCT
20 	Test PLCC CKT Cards	EOP CTCC
21 	Perform Integrated Ships Control (ISC) System Inspection	2521/047 (AP-1)
22 	ICAS	MP0180
23 	Inspect Computer Internal Shocks and Fans	2020/001 (M-3)
24 	Inspect all Cabinet Air Filters	2020/001 (M-3)
25 	Test ICAS Workstation UPS	2020/001 (S-1)
26 	Perform Operational Test	2020/001 (AP-2)
27 	Inspect overall compliance with reporting / IPARS, etc.
28 	ENGINE ORDER	MP0011
29 	Test EOT Wrong Direction Alarm (PACC and PLCC)	EOP EOT
30
BLEED AIR SYSTEM

 	A	B	C	D
1	Class: CG
2 	Inspection Deck:  MP
3 	Major System:  Bleed Air System
4 	Procedure Description	Reference	Results	Results
5	Bleed Air Systems	MP0100	1	2
6	Inspect Bleed Air System	EOP DBSA/DMBA, S9CG0-BW-SIB-010, NSTM 505, NSTM 254
7 	Inspect Installed Instruments.	CRL, NSTM 504,JFMM
8 	Inspect Drain Orifices and Low Point Drains	5516/006 (S-2)
9 	Inspect Prairie Air Cooler	S9CG0-BQ-SSM-020
10 	Inspect Masker Air Cooler	S9CG0-BQ-SSM-020
11 	Inspect Prairie Air Roto Seal	S9245-AV-MMA-010
12 	Inspect GTM Bleed Air Reg Valve Settings	5516/006 (AP-1)
13 	Inspect GTG Bleed Air Reg Valve Settings	5516/006 (AP-1)
14 	Test Bleed Air Control System	EOP CBAA
15 	Test Bleed Air System Solenoid Operated Valves	EOP CBAA
16 	Test Motor Air Reg valve	EOP CPTM
17 	Test Masker Air Transfer Valve	EOP CMSI
18 	Test Mixing Bypass valve	EOP CMSI
19 	Test HP Start Reg valve	EOP CMSI
20 	Test GTM 16th Stage Bleed Air valves	EOP CMSI
21 	Test GTG 14th Stage Bleed Air valve	5516/006 (AP-1)
22 	Test GTG /GTM Bleed Air Check Valves	5516/006 (AP-1)
23 	Test Bleed Air Low Pressure Alarm	5516/006 (AP-1)
24
WASTE HEAT SYSTEM

 	A	B	C	D	E
1	Class: CG
2 	Inspection Deck: MP
3 	Major System:  Waste Heat Systems
4 	Procedure Description	Reference	Results	Results	Results
5	Waste Heat Boiler	MP0210	1	2	3
6	COLD PLANT:
7 	Inspect WHB Casing and Ducting	5172/006 (AP-6)
8 	-Steam Drum	S9237-AA-MMA-010
9 	-Steam Generator Module	S9237-AA-MMA-010
10 	Inspect WHB	S9237-AA-MMA-010, NSTM 221
11 	-Gauge Glass Lighting and Isolation Valves	S9237-AA-MMA-010, NSTM 505
12 	-Hand Easing Gear	S9237-AA-MMA-010
13 	-Feedwater Control Valve	S9237-AA-MMA-010
14 	-Dump Valve	S9237-AA-MMA-010
15 	-Control Condenser S/W Regulating Valve	S9237-AA-MMA-010
16 	-Safety Valves	S9237-AA-MMA-010
17 	-Foundation	S9237-AA-MMA-010
18 	Inspect Installed Instruments.	CRL, NSTM 504,JFMM
19 	HOT PLANT:	MP0210
20 	Perform Operational Test of WHB System	5172/006 (AP-1)
21 	Test WHB Alarms	5172/006 (AP-2,AP-3)
22 	FEED AND CONDENSATE SYSTEM	MP0210
23 	Inspect Feedwater Pump	S9237-AA-MMA-010
24 	Inspect Circulating Pump	S9237-AA-MMA-010
25 	Inspect Condensate Cooler and Temp Reg Valve	S9237-AA-MMA-010
26 	Inspect Control Condenser and Temp Reg Valve	S9237-AA-MMA-010
27 	Inspect operation of CIT system	NSTM 220 V2
28 	Test Conductivity/Salinity Alarms	4371/004 (S-1)
29 	Test Feed and Drain Collecting Tank Alarms	5172/006 (AP-7)
30 	DFT	MP0150	1	2
31 	Inspect DFT	NSTM 255 V2
32 	-Relief Valve	NSTM 505
33 	-Gauge Glass Lighting and Isolation Valves	NSTM 221
34 	Test DFT for D.O.	NSTM 220
35
HULL

 	A	B	C	D
1	Class: CG
2 	Inspection Deck:  MP
3 	Major System:  Controls
4 	Procedure Description	Reference	Results	Results
5	Hull Structure	DC0380	1	2
6	Bilges	1000/005 (AP-1)
7 	Deck Plates	EOP MLOC
8 	Equipment Foundations	NSTM 631
9 	Pipe Brackets/Hangers	NSTM 505
10 	Paint and Preservation	NSTM 631
11 	Inspect Lighting	NSTM 300
12
UNDERWAY

 	A	B	C	D
1	Class: CG
2 	Inspection Deck:  MP
3 	Major System:  Underway
4 	Procedure Description	Reference	Results	Results
5	MAIN PROPULSION UNDERWAY PHASE	1	2
6	FULL POWER AND QUICK REVERSAL DEMONSTRATIONS	MP0070
7 	Demonstrate Auto Plant Mode Logic (Split plant to Full Power)	EOP CSSF
8 	Demonstrate Full Power Ahead	EOSS MUFP
9 	FULL POWER AND QUICK REVERSAL DEMONSTRATIONS	MP0080
10 	Demonstrate Quick Reversal Astern	EOSS MUFP
11 	Demonstrate Quick Reversal Ahead	EOSS MUFP
12 	FUEL OIL TRANSFER DEMONSTRATION	MP0120
13 	Demonstrate Fuel Oil Purifier Operation	EOSS SFSS
14 	Demonstrate Purifier Emergency Stop	S9261-AQ-MMA-010
15 	Test Fuel Oil Purifier Emergency Stop Capability	S9261-AQ-MMA-010
16 	PRAIRIE/ MASKER/BLEED AIR SYSTEM DEMONSTRATIONS	MP0130
17 	Measure Masker Air Flow Rates	5516/006 (R-1Q)
18 	Measure Prairie Air Flow Rates	5516/006 (U-3)
19 	Measure Masker Air Set Points to P/S Ropeguard and Fairwater Emitters	5516/006 (U-3)
20 	Test Operation of Anti-Icing Throttle Valve Indicator Lights	5516/006 (AP-2)
21 	WHB DEMONSTRATIONS	MP0210
22 	Test Boiler Water Chemistry	NSTM 220 V2
23 	Conduct Generating Bank and Separator Blowdown (Surface and Bottom Blowdown)	EOP WHBP
24 	Test Soot Blowers	EOP WHBP
25