*special note* 2 backslashes "//" indicate a comment follows.
----------------------------------------
820CS QUICK CONFIG setup and programming
----------------------------------------


SET PC TO 192.168.1.10
Default 820cs Radio Login 192.168.1.1 - USE Internet Explorer
User: admin
Pass: admin

Plug your Nic card into the ETH1/POE port on your 820CS radio. //Doubble check this. they may be able to just use the MGMT port.

USING QUICK CONFIG
1. Turn off the yellow anoying background.
-Platform
	-Activation Key
		-Activation Key Configuration
			//at the bottem
			-Demo Mode Configuration
				Demo admin:Enable //remember you have 30 days to apply a valid Activation Key, or your radio will stop working.

To use quick config your firmwhere must be updated to 8.2 or higher.
//to check your version go to:
-Platform
	-Software
		-Versions
			Current software versions table:
Old firmware
			Package Name		Running Version
			nou 			8.0.0.0.0.338

New firmware
			Package Name		Running Version
			nou 			8.3.0.0.0.495

IF your radio is running an older version please update first.

1. Link setup
-Quick Configuration
	-Link Setup (PIPE)
		-1+0
//***Finish quick config setup process notes and instructions.

#. Other Settings
-Platform
	-Management
		-Unit Parameters
			Name:<Device Name Here> //Eg. ILV-820c-FIV-KST
			Contact Person:noc@risebroadband.com
			Location:<3 letter site code> //Eg.FIV
Click Apply

-Platform
	-Management
		-NTP Config.
			Admin: Enable
			NTP version:3 or 4 //i think both work.
			NTP Server IP Address: 66.254.202.7

Click Apply

-Platform
	-Management
		-Time Services
			Offset from GMT
			UTC offset hours -6 //for central time
Click Apply

//Some people wait to do the IP till the end. your choice.
-Platform
	-Management
		-Networking
			-Local
				Ip:192.168.1.1
				Subnet Mask:255.255.255.128
				gateway:192.168.1.1
				Ipv6:Leave Default
				Default Gatway IPv6:Leave Default
Click Apply //unit may apply the new settings immediately;

-Platform
	-Management
		-SNMP
			Admin: Enable
			SNMP Read Community: SnmpAcc344
			SNMP Write Community: private
			SNMP Trap Version: V2
Click Apply

-Platform
	-Softwhere
		-Download & Install
			Download & Install - Configuration parameters
				File transfer protocol: FTP
				Username:towerdawg
				Password:D1sMyh0us3!
				Server IPv4 address:192.168.1.10 (or ip of whatever your NIC card is set to. (your laptop/computer local IPv4)
				Server IPv6 address:NOT USED
				Path:820cs_newest    (this is the name of the folder the files are located in).
				File Name: --Leave Blank--
				Server IPV6 address :: --Leave Blank--
Click Apply

-Platform
	-Security
		-Access Control
			-Change Password
				User name:admin
				Old Password:admin
				New Password:BhAcc344
				Reenter Password:BhAcc344
Click Apply



SECTION ON APPLYING LICENCE KEY TO COME.

SECTION ON TROUBBLESHOOTING TO COME.




1. Set Frequencies
-Radio
	-Radio Parameters
Select Each Radio Location seperatly
EDIT
TX freq: Check Licence Sheet
RX freq: Check Licence Sheet
TX Level(dBm) Check Licence Sheet
Turn down Tx power to -1 if testing on bench!!!!!
you dont want to burn out the radio!

2. MRMC Scripts
-Radio
	-MRMC
		-Symmetrical Scripts
			-FCC
Select Radio Interface: Slot 2 port 1 etc.
DO THIS FOR BOTH:	Slot 2 port 2 etc.
(This is the radio interface your working on)

SELECT Script ID. From the list.
Check Licence Sheet for Which script ID to use.
Where Licence Sheet says Equipment Model. eg PTP 18820C_FCC_80_8 SP
80 = channel bandwith

CONFIGURE SCRIPT
MRMC Script Operational Mode: adaptive
PROFILE
Select your profile.
Check licence sheet for QAM level. eg.QAM/1024
Generaly Higher QAM is better.
If given choice between two same QAM levels,
pick the one with higher bandwith capacity
Eg. 	Profile 9, 1024 QAM, 598.688 Mbps
	Profile 9, 1024 QAM, 635.551 Mbps <-- Choose this one
APPLY
When you Apply, Radio WILL REBOOT! Wait!

3. SERVICE POINTS
-Ethernet
	- Services
	dont Mess with MNG
ADD
	Service type: PTP
	EVC ID: DATA CORE 1
	EVC DESC. DATA CORE 1
Apply
Select Service you just created
Click service points
ADD
	Service point 1
	Service point name ETH1 DATA

	Service point 2
	Service point name Wireless DATA 1
PIPE s-tag
ADD
	Service type: PTP
	EVC ID: DATA CORE 2
	EVC DESC. DATA CORE 2
Apply
Select Service you just created
Click service points
ADD
	Service point 1
	Service point name ETH2 DATA

	Service point 2
	Service point name Wireless DATA 2
PIPE s-tag
**When using SFP in Eth2**
-Ethernet
	-Interfaces
		-Physical Interfaces
Edit Ethernet: Slot 1, Port 2
Auto Negotiation: OFF

4.) UNIT Params.
-Platform
	-Management
		-Unit Parameters
Name Eg.:ILV-BHC820-ALP-RFD-1
Contact Person: noc@jabbroadband.com
Measurement Format: Imperial
APPLY

5.) SET IP
- Platform
	-Management
		-IP ("Networking" on some firmwares)
			-Local
This is the default, you'll want to get IP from networking or
existing infastructure.
Description: LEAVE ALONE
IP:192.168.1.1
Sub:255.255.255.0
Gate:192.168.1.1
APPLY

6. NTP
-Platform
	-Management
		-NTP Config.
NTP Server IP Address: 66.254.202.7
Admin: ENABLE
APPLY

7. SNMP
-Platform
	-Management
		- SNMP
			-SNMP Parameters
SNMP Read Community:SnmpAcc344
SNMP Write Community:SnmpAcc344
APPLY

8. Set XPIC
- Platform
	-Radio
		-Groups
			-XPIC
OR located under
- Radio
	-Groups
		-XPIC
Admin State: Enable
APPLY

9. PASSWORD
- Platform
	-Security
		-Access Control
			-Change Password
Standard Back Haul Password
Old Password:admin
Username:admin
Password:BhAcc344

10. TURN OFF MUTE !!!!! This will need to be done 8 times if working with a
dual radio setup.
-Radio
	-Radio Parameters
Select Each Radio Location Seperatly
Radio: Slot2, Port 1
Radio: Slot2, Port 2
Edit
TX Mute: OFF
APPLY