sudo smartctl --all /dev/sdd

smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.91-1-MANJARO] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 3.5" DT01ACA... Desktop HDD
Device Model:     TOSHIBA DT01ACA300
Serial Number:    446LH8GGS
LU WWN Device Id: 5 000039 ff4d67f84
Firmware Version: MX6OABB0
User Capacity:    3 000 592 982 016 bytes [3,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Sat Jan 18 00:02:32 2020 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                    was suspended by an interrupting command from host.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:        (21648) seconds.
Offline data collection
capabilities:            (0x5b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    No Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:    (   1) minutes.
Extended self-test routine
recommended polling time:    ( 361) minutes.
SCT capabilities:          (0x003d) SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   140   140   054    Pre-fail  Offline      -       67
  3 Spin_Up_Time            0x0007   156   156   024    Pre-fail  Always       -       416 (Average 321)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       80
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       2
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   121   121   020    Pre-fail  Offline      -       34
  9 Power_On_Hours          0x0012   098   098   000    Old_age   Always       -       17851
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       77
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       213
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       213
194 Temperature_Celsius     0x0002   153   153   000    Old_age   Always       -       39 (Min/Max 18/53)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       2
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 3
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 3 occurred at disk power-on lifetime: 17740 hours (739 days + 4 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 68 98 d0 31 0e  Error: UNC 104 sectors at LBA = 0x0e31d098 = 238145688

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 00 d0 31 e0 00      03:39:56.970  READ DMA EXT
  25 00 00 00 cf 31 e0 00      03:39:56.945  READ DMA EXT
  25 00 00 00 ce 31 e0 00      03:39:56.944  READ DMA EXT
  25 00 00 00 cd 31 e0 00      03:39:56.943  READ DMA EXT
  25 00 00 00 cc 31 e0 00      03:39:56.943  READ DMA EXT

Error 2 occurred at disk power-on lifetime: 17677 hours (736 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 68 98 d0 31 0e  Error: UNC at LBA = 0x0e31d098 = 238145688

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 a8 00 d0 31 40 00      02:27:30.540  READ FPDMA QUEUED
  60 00 a0 00 cf 31 40 00      02:27:30.539  READ FPDMA QUEUED
  60 00 98 00 ce 31 40 00      02:27:30.538  READ FPDMA QUEUED
  60 00 90 00 cd 31 40 00      02:27:30.537  READ FPDMA QUEUED
  60 00 88 00 cc 31 40 00      02:27:30.537  READ FPDMA QUEUED

Error 1 occurred at disk power-on lifetime: 16298 hours (679 days + 2 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 98 1b bc 04  Error: UNC at LBA = 0x04bc1b98 = 79436696

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 c0 30 e0 1f bc 40 08   1d+02:59:44.955  READ FPDMA QUEUED
  60 c0 28 e0 1e bc 40 08   1d+02:59:44.955  READ FPDMA QUEUED
  60 40 20 a0 1f bc 40 08   1d+02:59:44.953  READ FPDMA QUEUED
  60 40 18 60 1e bc 40 08   1d+02:59:44.952  READ FPDMA QUEUED
  60 00 10 60 1d bc 40 08   1d+02:59:44.952  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.