Guest User

Untitled

a guest
Jun 19th, 2020
17
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  2. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  3. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  4.  
  5. # Basic motion configuration
  6. default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves
  7. default_seek_rate 4000 # Default speed (mm/minute) for G0 moves
  8. mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable
  9. #mm_per_line_segment 5 # Cut lines into segments this size
  10. mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
  11. # note it is invalid for both the above be 0
  12. # if both are used, will use largest segment length based on radius
  13.  
  14. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  15. # See http://smoothieware.org/stepper-motors
  16. alpha_steps_per_mm 320 # Steps per mm for alpha ( X ) stepper
  17. beta_steps_per_mm 320 # Steps per mm for beta ( Y ) stepper
  18. gamma_steps_per_mm 215 # Steps per mm for gamma ( Z ) stepper
  19.  
  20. # Planner module configuration : Look-ahead and acceleration configuration
  21. # See http://smoothieware.org/motion-control
  22. acceleration 3000 # Acceleration in mm/second/second.
  23. #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  24. junction_deviation 0.04 # See http://smoothieware.org/motion-control#junction-deviation
  25. #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  26.  
  27. # Stepper module configuration
  28. microseconds_per_step_pulse 3 # Duration of step pulses to stepper drivers, in microseconds
  29. base_stepping_frequency 100000 # Base frequency for stepping
  30.  
  31. # Cartesian axis speed limits
  32. x_axis_max_speed 4500 # Maximum speed in mm/min
  33. y_axis_max_speed 4500 # Maximum speed in mm/min
  34. z_axis_max_speed 4000 # Maximum speed in mm/min
  35.  
  36. # Stepper module configuration
  37. # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
  38. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  39. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  40. alpha_dir_pin 0.5! # Pin for alpha stepper direction, add '!' to reverse direction
  41. alpha_en_pin 0.4 # Pin for alpha enable pin
  42. alpha_current 1.5 # X stepper motor current
  43. alpha_max_rate 12000.0 # Maximum rate in mm/min
  44.  
  45. beta_step_pin 2.1 # Pin for beta stepper step signal
  46. beta_dir_pin 0.11! # Pin for beta stepper direction, add '!' to reverse direction
  47. beta_en_pin 0.10 # Pin for beta enable
  48. beta_current 1.5 # Y stepper motor current
  49. beta_max_rate 12000.0 # Maxmimum rate in mm/min
  50.  
  51. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  52. gamma_dir_pin 0.20! # Pin for gamma stepper direction, add '!' to reverse direction
  53. gamma_en_pin 0.19 # Pin for gamma enable
  54. gamma_current 1.5 # Z stepper motor current
  55. gamma_max_rate 1000.0 # Maximum rate in mm/min
  56.  
  57. ## Extruder module configuration
  58. # See http://smoothieware.org/extruder
  59. extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  60. extruder.hotend.steps_per_mm 6009.52 # Steps per mm for extruder stepper
  61. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  62. extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
  63. extruder.hotend.max_speed 15 # Maximum speed in mm/s
  64.  
  65. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  66. extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal ( add '!' to reverse direction )
  67. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  68.  
  69. # Extruder offset
  70. #extruder.hotend.x_offset 0 # X offset from origin in mm
  71. #extruder.hotend.y_offset 0 # Y offset from origin in mm
  72. #extruder.hotend.z_offset 0 # Z offset from origin in mm
  73.  
  74. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  75. #extruder.hotend.retract_length 3 # Retract length in mm
  76. #extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec
  77. #extruder.hotend.retract_recover_length 0 # Additional length for recover
  78. #extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
  79. #extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
  80. #extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  81.  
  82. delta_current 1.5 # First extruder stepper motor current
  83.  
  84. # Second extruder module configuration
  85. extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  86. extruder.hotend2.steps_per_mm 194 # Steps per mm for extruder stepper
  87. extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  88. extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  89. extruder.hotend2.max_speed 50 # mm/s
  90.  
  91. extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  92. extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
  93. extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  94.  
  95. extruder.hotend2.x_offset 20.07 # x offset from origin in mm
  96. extruder.hotend2.y_offset 0 # y offset from origin in mm
  97. extruder.hotend2.z_offset 0 # z offset from origin in mm
  98.  
  99. epsilon_current 1.5 # Second extruder stepper motor current
  100.  
  101.  
  102. ## Laser module configuration
  103. # See http://smoothieware.org/laser
  104. #laser_module_enable false # Whether to activate the laser module at all
  105. #laser_module_pwm_pin 2.5 # This pin will be PWMed to control the laser.
  106. # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
  107. # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
  108. #laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off.
  109. #laser_module_maximum_power 1.0 # This is the maximum duty cycle that will be applied to the laser
  110. #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
  111. # active without actually burning.
  112. #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
  113. # the maximum and minimum power levels specified above
  114. #laser_module_pwm_period 20 # This sets the pwm frequency as the period in microseconds
  115.  
  116. ## Temperature control configuration
  117. # See http://smoothieware.org/temperaturecontrol
  118.  
  119. # First hotend configuration
  120. temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
  121. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  122. temperature_control.hotend.heater_pin 1.23 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  123. temperature_control.hotend.sensor Honeywell100K # See http://smoothieware.org/temperaturecontrol#toc5
  124. #temperature_control.hotend.beta 4066 # Or set the beta value
  125. temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
  126. temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  127. temperature_control.hotend.designator T # Designator letter for this module
  128. temperature_control.hotend.max_temp 80 # Set maximum temperature - Will prevent heating above 300 by default
  129. temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  130. temperature_control.hotend.pwm_frequency 20
  131.  
  132. # Safety control is enabled by default and can be overidden here, the values show the defaults
  133. # See http://smoothieware.org/temperaturecontrol#runaway
  134. temperature_control.hotend.runaway_heating_timeout 1000# How long it can take to heat up, max is 2040 seconds.
  135. temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  136. temperature_control.hotend.runaway_range 50 # How far from the set temperature it can wander, max setting is 63°C
  137.  
  138. # PID configuration extruder 1
  139. # See http://smoothieware.org/temperaturecontrol#pid
  140. temperature_control.hotend.p_factor 60.1 # P ( proportional ) factor
  141. temperature_control.hotend.i_factor 1.274 # I ( integral ) factor
  142. temperature_control.hotend.d_factor 708 # D ( derivative ) factor
  143.  
  144.  
  145. # Second hotend configuration
  146. temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
  147. temperature_control.hotend2.thermistor_pin 0.24 # Pin for the thermistor to read
  148. temperature_control.hotend2.heater_pin 1.31 # Pin that controls the heater
  149. temperature_control.hotend2.sensor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  150. #temperature_control.hotend2.beta 4066 # or set the beta value
  151. temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
  152. temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  153. temperature_control.hotend2.designator T1 # Designator letter for this module
  154. temperature_control.hotend2.max_temp 100 # Set maximum temperature - Will prevent heating above 300 by default
  155. temperature_control.hotend2.pwm_frequency 20
  156.  
  157. # PID configuration extruder 2
  158. # See http://smoothieware.org/temperaturecontrol#pid
  159. temperature_control.hotend2.p_factor 23.6 # P ( proportional ) factor
  160. temperature_control.hotend2.i_factor 1.873 # I ( integral ) factor
  161. temperature_control.hotend2.d_factor 75 # D ( derivative ) factor
  162.  
  163. # Safety control is enabled by default and can be overidden here, the values show the defaults
  164. # See http://smoothieware.org/temperaturecontrol#runaway
  165. temperature_control.hotend2.runaway_heating_timeout 1000# How long it can take to heat up, max is 2040 seconds.
  166. temperature_control.hotend2.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  167. temperature_control.hotend2.runaway_range 50 # How far from the set temperature it can wander, max setting is 63°C
  168. #temperature_control.hotend2.max_pwm 255 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
  169.  
  170. # Third hotend configuration
  171. temperature_control.hotend3.enable true # Whether to activate this ( "hotend" ) module at all.
  172. temperature_control.hotend3.thermistor_pin 0.25 # Pin for the thermistor to read
  173. temperature_control.hotend3.heater_pin 1.30 # Pin that controls the heater
  174. temperature_control.hotend3.sensor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  175. #temperature_control.hotend3.beta 4066 # or set the beta value
  176. temperature_control.hotend3.set_m_code 104 # M-code to set the temperature for this module
  177. temperature_control.hotend3.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  178. temperature_control.hotend3.designator T2 # Designator letter for this module
  179. temperature_control.hotend3.max_temp 100 # Set maximum temperature - Will prevent heating above 300 by default
  180. temperature_control.hotend3.pwm_frequency 20
  181.  
  182. # PID configuration extruder 3
  183. # See http://smoothieware.org/temperaturecontrol#pid
  184. temperature_control.hotend3.p_factor 23.6 # P ( proportional ) factor
  185. temperature_control.hotend3.i_factor 1.873 # I ( integral ) factor
  186. temperature_control.hotend3.d_factor 75 # D ( derivative ) factor
  187.  
  188. # Safety control is enabled by default and can be overidden here, the values show the defaults
  189. # See http://smoothieware.org/temperaturecontrol#runaway
  190. temperature_control.hotend3.runaway_heating_timeout 1000# How long it can take to heat up, max is 2040 seconds.
  191. temperature_control.hotend3.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  192. temperature_control.hotend3.runaway_range 50 # How far from the set temperature it can wander, max setting is 63°C
  193.  
  194.  
  195.  
  196.  
  197. temperature_control.bed.enable true # Whether to activate this ( "hotend" ) module at all.
  198. temperature_control.bed.thermistor_pin 0.26 # Pin for the thermistor to read
  199. temperature_control.bed.heater_pin 2.7 # Pin that controls the heater
  200. temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  201. #temperature_control.bed.beta 3974 # Or set the beta value
  202. temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
  203. temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
  204. temperature_control.bed.designator B # Designator letter for this module
  205.  
  206. # Bang-bang ( simplified ) control
  207. # See http://smoothieware.org/temperaturecontrol#bang-bang
  208. temperature_control.bed.bang_bang true # Set to true to use bang bang control rather than PID
  209. temperature_control.bed.hysteresis 5.0 # Set to the temperature in degrees C to use as hysteresis
  210.  
  211. ## Switch modules
  212. # See http://smoothieware.org/switch
  213.  
  214. # Switch module for fan control
  215. #switch.fan.enable true # Enable this module
  216. #switch.fan.input_on_command M106 # Command that will turn this switch on
  217. #switch.fan.input_off_command M107 # Command that will turn this switch off
  218. #switch.fan.output_pin 2.6 # Pin this module controls
  219. #switch.fan.output_type pwm # PWM output settable with S parameter in the input_on_comand
  220. #switch.fan.max_pwm 255 # Set max pwm for the pin default is 255
  221.  
  222. #switch.misc.enable true # Enable this module
  223. #switch.misc.input_on_command M42 # Command that will turn this switch on
  224. #switch.misc.input_off_command M43 # Command that will turn this switch off
  225. #switch.misc.output_pin 2.5 # Pin this module controls
  226. #switch.misc.output_type digital # Digital means this is just an on or off pin
  227.  
  228. switch.heatfan.enable true #
  229. switch.heatfan.output_pin 1.22 # sw pwm can use any digital pin
  230. switch.heatfan.input_on_command M280 #
  231. switch.heatfan.input_off_command halt #
  232. switch.heatfan.output_type digital # sw pwm must be low frequency
  233. #switch.heatfan.pwm_period_ms 20 # 50Hz
  234. #switch.heatfan.startup_value 7.43 # On boot it will go into stow mode, also set with the M281
  235. #switch.heatfan.default_on_value 3.3 # if M280 is issued without S this is the value it will set it to
  236. switch.heatfan.startup_state true #Startup state of the switch. If set to False the module is initialized OFF, if set to True the module is initialized ON
  237.  
  238. ## Temperatureswitch
  239. # See http://smoothieware.org/temperatureswitch
  240. # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  241. # Useful to turn on a fan or water pump to cool the hotend
  242. temperatureswitch.hotend2.enable true #
  243. temperatureswitch.hotend2.designator T1 # first character of the temperature control designator to use as the temperature sensor to monitor
  244. temperatureswitch.hotend2.switch heatfan # select which switch to use, matches the name of the defined switch
  245. temperatureswitch.hotend2.threshold_temp 80.0 # temperature to turn on (if rising) or off the switch
  246. temperatureswitch.hotend2.heatup_poll .5 # poll heatup at 15 sec intervals
  247. temperatureswitch.hotend2.cooldown_poll 60 # poll cooldown at 60 sec intervals
  248. temperatureswitch.hotend2.trigger rising # can be level, rising, falling - level is the default
  249. temperatureswitch.module_name.inverted true # will turn the switch off when the temp > target and vice versa when set true
  250.  
  251. ## Endstops
  252. # See http://smoothieware.org/endstops
  253. endstops_enable true # The endstop module is enabled by default and can be disabled here
  254. #corexy_homing false # Set to true if homing on a hbot or corexy
  255. alpha_min_endstop 1.24!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  256. #alpha_max_endstop 1.25^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  257. alpha_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  258. alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
  259. alpha_max 210 # This gets loaded as the current position after homing when home_to_max is set
  260. beta_min_endstop 1.26!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  261. #beta_max_endstop 1.27^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  262. beta_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  263. beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
  264. beta_max 210 # This gets loaded as the current position after homing when home_to_max is set
  265. gamma_min_endstop 1.28!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  266. #gamma_max_endstop 1.29 # Pin to read max endstop, uncomment this and comment the above if using max endstops
  267. gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  268. gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
  269. gamma_max 300 # This gets loaded as the current position after homing when home_to_max is set
  270.  
  271. alpha_max_travel 210 # Max travel in mm for alpha/X axis when homing
  272. beta_max_travel 210 # Max travel in mm for beta/Y axis when homing
  273. gamma_max_travel 310 # Max travel in mm for gamma/Z axis when homing
  274.  
  275. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
  276. #alpha_limit_enable false # Set to true to enable X min and max limit switches
  277. #beta_limit_enable false # Set to true to enable Y min and max limit switches
  278. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  279.  
  280. # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
  281. alpha_fast_homing_rate_mm_s 30 # Alpha/X fast homing feedrate in mm/second
  282. alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
  283. beta_fast_homing_rate_mm_s 30 # Beta/Y fast homing feedrate in mm/second
  284. beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
  285. gamma_fast_homing_rate_mm_s 15 # Gamma/Z fast homing feedrate in mm/second
  286. gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
  287.  
  288. alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
  289. beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
  290. gamma_homing_retract_mm 1 # Distance to retract from the endstop after it is hit for gamma/Z
  291.  
  292.  
  293. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
  294. #alpha_limit_enable false # Set to true to enable X min and max limit switches
  295. #beta_limit_enable false # Set to true to enable Y min and max limit switches
  296. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  297.  
  298. # Optional order in which axis will home, default is they all home at the same time,
  299. # If this is set it will force each axis to home one at a time in the specified order
  300. homing_order YXZ # X axis followed by Y then Z last
  301. #move_to_origin_after_home false # Move XY to 0,0 after homing
  302. #endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
  303. #endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
  304. home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
  305.  
  306. # End of endstop config
  307. # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
  308. #include abc-endstop.config
  309.  
  310. ## Z-probe
  311. # See http://smoothieware.org/zprobe
  312. zprobe.enable false # Set to true to enable a zprobe
  313. zprobe.probe_pin 1.28!^ # Pin probe is attached to, if NC remove the !
  314. zprobe.slow_feedrate 5 # Mm/sec probe feed rate
  315. #zprobe.debounce_ms 1 # Set if noisy
  316. zprobe.fast_feedrate 100 # Move feedrate mm/sec
  317. zprobe.probe_height 5 # How much above bed to start probe
  318. #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
  319.  
  320. # Levelling strategy
  321. # Example for 3-point levelling strategy, see wiki documentation for other strategies
  322. #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  323. #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
  324. #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
  325. #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
  326. #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
  327. #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  328. #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
  329. #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
  330.  
  331. ## Panel
  332. # See http://smoothieware.org/panel
  333. # Please find your panel on the wiki and copy/paste the right configuration here
  334. panel.enable false # Set to true to enable the panel code
  335.  
  336. # Example for reprap discount GLCD
  337. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  338. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  339. #panel.lcd reprap_discount_glcd #
  340. #panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  341. #panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4
  342. #panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3
  343. #panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5
  344. #panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2
  345. #panel.buzz_pin 1.31 # Pin for buzzer ; GLCD EXP1 Pin 1
  346. #panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8
  347.  
  348. panel.menu_offset 0 # Some panels will need 1 here
  349.  
  350. panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
  351. panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
  352. panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
  353.  
  354. panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
  355. panel.bed_temperature 100 # Temp to set bed when preheat is selected
  356.  
  357. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  358. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  359. custom_menu.power_on.enable true #
  360. custom_menu.power_on.name Power_on #
  361. custom_menu.power_on.command M80 #
  362.  
  363. custom_menu.power_off.enable true #
  364. custom_menu.power_off.name Power_off #
  365. custom_menu.power_off.command M81 #
  366.  
  367.  
  368. ## Network settings
  369. # See http://smoothieware.org/network
  370. network.enable false # Enable the ethernet network services
  371. network.webserver.enable true # Enable the webserver
  372. network.telnet.enable true # Enable the telnet server
  373. network.ip_address auto # Use dhcp to get ip address
  374. # Uncomment the 3 below to manually setup ip address
  375. #network.ip_address 192.168.3.222 # The IP address
  376. #network.ip_mask 255.255.255.0 # The ip mask
  377. #network.ip_gateway 192.168.3.1 # The gateway address
  378. #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
  379.  
  380. ## System configuration
  381. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  382. # For communication over the UART port, *not* the USB/Serial port
  383. uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
  384.  
  385. second_usb_serial_enable true # This enables a second USB serial port
  386. #leds_disable true # Disable using leds after config loaded
  387. #play_led_disable true # Disable the play led
  388.  
  389. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  390. # See http://smoothieware.org/killbutton
  391. kill_button_enable true # Set to true to enable a kill button
  392. kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  393.  
  394. #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  395. #dfu_enable false # For linux developers, set to true to enable DFU
  396.  
  397. # Only needed on a smoothieboard
  398. # See http://smoothieware.org/currentcontrol
  399. currentcontrol_module_enable true # Control stepper motor current via the configuration file
RAW Paste Data