Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- BootROM 1.34
- Booting from NAND flash
- BootROM: Image checksum verification PASSED
- __ __ _ _
- | \/ | __ _ _ ____ _____| | |
- | |\/| |/ _` | '__\ \ / / _ \ | |
- | | | | (_| | | \ V / __/ | |
- |_| |_|\__,_|_| \_/ \___|_|_|
- _ _ ____ _
- | | | | | __ ) ___ ___ | |_
- | | | |___| _ \ / _ \ / _ \| __|
- | |_| |___| |_) | (_) | (_) | |_
- \___/ |____/ \___/ \___/ \__|
- ** LOADER **
- U-Boot 2009.08 (May 22 2014 - 18:26:38) Marvell version: 2.1.6_NQ
- Board: MI424WR-I
- SoC: 88F6560 A0
- CPU: Marvell Feroceon (Rev 1) - LE
- CPU @ 1200Mhz, L2 @ 480Mhz
- DDR3 @ 400Mhz, TClock @ 200Mhz
- PEX 0: Root Complex Interface, Detected Link X1
- PEX 1: Detected No Link.
- DRAM: 128 MB
- CS 0: base 0x00000000 size 128 MB
- Addresses 10M - 0M are saved for the U-Boot usage.
- NAND: 1bit HM ECC, Size: 128 MiB
- USB 0: Host Mode
- Shutting down unused interfaces:
- PON
- SATA
- 3xFE-PHY
- Modules Detected:
- No PON module.
- RGMIIA Module on Switch port #6.
- RGMIIB Module on MAC0.
- Ethernet Switch on MAC1.
- QSGMII Module.
- Initialized 1545 PHY
- Net: egiga0, egiga1 [PRIME]
- Hit any key to stop autoboot: 1 0
- Marvell>> help
- ? - alias for 'help'
- SatR - Sample At Reset sub-system
- autoscr - DEPRECATED - use "source" command instead
- base - print or set address offset
- bdinfo - print Board Info structure
- boot - boot default, i.e., run 'bootcmd'
- bootd - boot default, i.e., run 'bootcmd'
- bootext2- bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name
- bootm - boot application image from memory
- bootp - boot image via network using BOOTP/TFTP protocol
- bubt - bubt - Burn an image on the Boot Nand Flash.
- cmp - memory compare
- cmpm - cmpm - Compare Memory
- coninfo - print console devices and information
- cp - memory copy
- cpumap - cpumap - Display CPU memory mapping settings.
- crc32 - checksum calculation
- date - get/set/reset date & time
- dclk - dclk - Display the MV device CLKs.
- dhcp - boot image via network using DHCP/TFTP protocol
- diskboot- diskboot- boot from IDE device
- dualimage- sets openrg_start and openrg_size according to the current active image.
- echo - echo args to console
- eeprom - EEPROM sub-system
- ethCounters- ethShow - show the current ETH port counters
- ethShow - ethShow - scanning the PHYs status
- ext2load- load binary file from a Ext2 filesystem
- ext2ls - list files in a directory (default /)
- fatinfo - print information about filesystem
- fatload - load binary file from a dos filesystem
- fatls - list files in a directory (default /)
- fi - fi - Find value in the memory.
- fsinfo - print information about filesystems
- fsload - load binary file from a filesystem image
- g - g - start application at cached address 'addr'(default addr 0x40000)
- go - start application at address 'addr'
- help - print online help
- i2c - I2C sub-system
- ide - ide - IDE sub-system
- iminfo - print header information for application image
- imxtract- extract a part of a multi-image
- ir - ir - reading and changing MV internal register values.
- itest - return true/false on integer compare
- loadb - load binary file over serial line (kermit mode)
- loads - load S-Record file over serial line
- loady - load binary file over serial line (ymodem mode)
- loop - infinite loop on address range
- ls - list files in a directory (default /)
- map - map - Diasplay address decode windows
- md - memory display
- me - me - PCI master enable
- mii_dump- Dump mii registers
- mm - memory modify (auto-incrementing address)
- mmc - MMC sub-system
- mp - mp - map PCI BAR
- mpp - mpp
- mtest - simple RAM read/write test
- mux - mux set
- mw - memory write (fill)
- nand - NAND sub-system
- nboot - boot from NAND device
- nbubt - nbubt - Burn a boot loader image on the Boot Nand Flash.
- nfs - boot image via network using NFS protocol
- nm - memory modify (constant address)
- pci - list and access PCI Configuration Space
- pciePhyRead- phyRead - Read PCI-E Phy register
- pciePhyWrite- pciePhyWrite - Write PCI-E Phy register
- phyRead - phyRead - Read Phy register
- phyWrite- phyWrite - Write Phy register
- ping - send ICMP ECHO_REQUEST to network host
- printenv- print environment variables
- rarpboot- boot image via network using RARP/TFTP protocol
- rcvr - rcvr - Satrt recovery process (Distress Beacon with TFTP server)
- reset - Perform RESET of the CPU
- resetenv- resetenv - earse environment sector to reset all variables to default.
- run - run commands in an environment variable
- saveenv - save environment variables to persistent storage
- se - se - PCI Slave enable
- setenv - set environment variables
- sg - sg - scanning the PHYs status
- sleep - delay execution for some time
- source - run script from memory
- sp - sp - Scan PCI bus.
- switchCountersRead- switchCntPrint - Read switch port counters.
- switchPhyRegRead- - Read switch register
- switchPhyRegWrite- - Write switch register
- switchRegRead- switchRegRead - Read switch register
- switchRegWrite- switchRegWrite - Write switch register
- tftpboot- boot image via network using TFTP protocol
- usb - USB sub-system
- usbboot - boot from USB device
- version - print monitor version
- Marvell>> mii dev
- [de: 0: 0] = 0
- [de: 0: 1] = 0
- [de: 0: 2] = 0
- [de: 0: 3] = 0
- [de: 0: 4] = 0
- [de: 0: 5] = 0
- [de: 0: 6] = 0
- [de: 0: 7] = 0
- [de: 0: 8] = 0
- [de: 0: 9] = 0
- [de: 0: a] = 0
- [de: 0: b] = 0
- [de: 0: c] = 0
- [de: 0: d] = 0
- [de: 0: e] = 0
- [de: 0: f] = 0
- [de: 0:10] = 0
- [de: 0:11] = 0
- [de: 0:12] = 0
- [de: 0:13] = 0
- [de: 0:14] = 0
- [de: 0:15] = 0
- [de: 0:16] = 0
- [de: 0:17] = 0
- [de: 0:18] = 0
- [de: 0:19] = 0
- [de: 0:1a] = 0
- [de: 0:1b] = 0
- [de: 0:1c] = 0
- [de: 0:1d] = 0
- [de: 0:1e] = 0
- [de: 0:1f] = 0
- Marvell>> mii info
- [ 0: 0: 0] = 1140
- [ 0: 0: 1] = 7949
- [ 0: 0: 2] = 141
- [ 0: 0: 3] = ea1
- [ 0: 0: 4] = 5e1
- [ 0: 0: 5] = 0
- [ 0: 0: 6] = 4
- [ 0: 0: 7] = 2001
- [ 0: 0: 8] = 0
- [ 0: 0: 9] = f00
- [ 0: 0: a] = 4000
- [ 0: 0: b] = 0
- [ 0: 0: c] = 0
- [ 0: 0: d] = 3
- [ 0: 0: e] = 0
- [ 0: 0: f] = 3000
- [ 0: 0:10] = 3360
- [ 0: 0:11] = 8050
- [ 0: 0:12] = 0
- [ 0: 0:13] = 50
- [ 0: 0:14] = 20
- [ 0: 0:15] = 0
- [ 0: 0:16] = 0
- [ 0: 0:17] = 0
- [ 0: 0:18] = 0
- [ 0: 0:19] = 0
- [ 0: 0:1a] = 40
- [ 0: 0:1b] = 0
- [ 0: 0:1c] = 0
- [ 0: 0:1d] = 0
- [ 0: 0:1e] = 0
- [ 0: 0:1f] = 0
- Marvell>>
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement