Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- [ 0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 14:39:33 CET 2016
- [ 0.000000] SoC Type: Ralink RT3350 id:1 rev:2
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
- [ 0.000000] MIPS: machine is D-Link DIR-300 B1
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x00000000-0x01ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
- [ 0.000000] On node 0 totalpages: 8192
- [ 0.000000] free_area_init_node: node 0, pgdat 802f6290, node_mem_map 81000000
- [ 0.000000] Normal zone: 64 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 8192 pages, LIFO batch:0
- [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
- [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- [ 0.000000] pcpu-alloc: [0] 0
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Writing ErrCtl register=00022101
- [ 0.000000] Readback ErrCtl register=00022101
- [ 0.000000] Memory: 28952K/32768K available (2508K kernel code, 119K rwdata, 492K rodata, 136K init, 185K bss, 3816K reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS:256
- [ 0.000000] CPU Clock: 320MHz
- [ 0.000000] clocksource_of_init: no matching clocksources found
- [ 0.070000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
- [ 0.080000] pid_max: default: 32768 minimum: 301
- [ 0.090000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.100000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.110000] pinctrl core: initialized pinctrl subsystem
- [ 0.120000] NET: Registered protocol family 16
- [ 0.130000] rt2880-pinmux pinctrl: try to register 52 pins ...
- [ 0.130000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux
- [ 0.130000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux
- [ 0.130000] pinctrl core: add 7 pinmux maps
- [ 0.130000] rt2880-pinmux pinctrl: found group selector 7 for sdram
- [ 0.130000] rt2880-pinmux pinctrl: found group selector 0 for i2c
- [ 0.130000] rt2880-pinmux pinctrl: found group selector 1 for spi
- [ 0.130000] rt2880-pinmux pinctrl: found group selector 4 for jtag
- [ 0.130000] rt2880-pinmux pinctrl: found group selector 5 for mdio
- [ 0.130000] rt2880-pinmux pinctrl: found group selector 6 for rgmii
- [ 0.130000] rt2880-pinmux pinctrl: found group selector 2 for uartf
- [ 0.130000] rt2880-pinmux pinctrl: request pin 24 (io24) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 25 (io25) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 26 (io26) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 27 (io27) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 28 (io28) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 29 (io29) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 30 (io30) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 31 (io31) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 32 (io32) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 33 (io33) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 34 (io34) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 35 (io35) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 36 (io36) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 37 (io37) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 38 (io38) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 39 (io39) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 1 (io1) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 2 (io2) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 3 (io3) for pinctrl
- [ 0.130000] rt2880-pinmux pinctrl: request pin 4 (io4) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 5 (io5) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 6 (io6) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 17 (io17) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 18 (io18) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 19 (io19) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 20 (io20) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 21 (io21) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 22 (io22) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 23 (io23) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 40 (io40) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 41 (io41) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 42 (io42) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 43 (io43) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 44 (io44) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 45 (io45) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 46 (io46) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 47 (io47) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 48 (io48) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 49 (io49) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 50 (io50) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 51 (io51) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 7 (io7) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 8 (io8) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 9 (io9) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 10 (io10) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 11 (io11) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 12 (io12) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 13 (io13) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: request pin 14 (io14) for pinctrl
- [ 0.140000] rt2880-pinmux pinctrl: failed to lookup the sleep state
- [ 0.150000] rt2880_gpio 10000600.gpio: registering 24 gpios
- [ 0.160000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
- [ 0.170000] Switched to clocksource MIPS
- [ 0.180000] NET: Registered protocol family 2
- [ 0.190000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.200000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.220000] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.230000] TCP: reno registered
- [ 0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.250000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.260000] NET: Registered protocol family 1
- [ 0.270000] rt-timer 10000100.timer: maximum frequency is 6510Hz
- [ 0.280000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
- [ 0.280000] futex hash table entries: 256 (order: -1, 3072 bytes)
- [ 0.320000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.340000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.420000] msgmni has been set to 56
- [ 0.430000] io scheduler noop registered
- [ 0.440000] io scheduler deadline registered (default)
- [ 0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
- [ 0.470000] serial8250 serial8250: no of_node; not parsing pinctrl DT
- [ 0.480000] pinctrl core: add 1 pinmux maps
- [ 0.480000] rt2880-pinmux pinctrl: found group selector 3 for uartlite
- [ 0.480000] rt2880-pinmux pinctrl: request pin 15 (io15) for 10000c00.uartlite
- [ 0.480000] rt2880-pinmux pinctrl: request pin 16 (io16) for 10000c00.uartlite
- [ 0.480000] console [ttyS0] disabled
- [ 0.480000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 6666666) is a 16550A
- [ 0.500000] console [ttyS0] enabled
- [ 0.520000] bootconsole [early0] disabled
- [ 0.540000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a00
- [ 0.560000] 1f000000.cfi: Found an alias at 0x400000 for the chip at 0x0
- [ 0.560000] Amd/Fujitsu Extended Query Table at 0x0040
- [ 0.570000] Amd/Fujitsu Extended Query version 1.3.
- [ 0.580000] number of CFI chips: 1
- [ 0.600000] 4 ofpart partitions found on MTD device 1f000000.cfi
- [ 0.610000] Creating 4 MTD partitions on "1f000000.cfi":
- [ 0.630000] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.640000] 0x000000030000-0x000000040000 : "devdata"
- [ 0.650000] 0x000000040000-0x000000050000 : "devconf"
- [ 0.660000] 0x000000050000-0x000000400000 : "firmware"
- [ 0.680000] 2 uimage-fw partitions found on MTD device firmware
- [ 0.690000] 0x000000050000-0x000000162ab4 : "kernel"
- [ 0.700000] 0x000000162ab4-0x000000400000 : "rootfs"
- [ 0.720000] mtd: device 5 (rootfs) set to be root filesystem
- [ 0.730000] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.740000] 0x000000390000-0x000000400000 : "rootfs_data"
- [ 0.760000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
- [ 0.780000] rt2880_wdt 10000120.watchdog: Initialized
- [ 0.790000] TCP: cubic registered
- [ 0.790000] NET: Registered protocol family 17
- [ 0.800000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
- [ 0.830000] Bridge firewalling registered
- [ 0.840000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.880000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 0.900000] Freeing unused kernel memory: 136K (8030e000 - 80330000)
- [ 2.230000] init: Console is alive
- [ 2.240000] init: - watchdog -
- [ 3.770000] usbcore: registered new interface driver usbfs
- [ 3.790000] usbcore: registered new interface driver hub
- [ 3.800000] usbcore: registered new device driver usb
- [ 3.810000] rt2880-pinmux pinctrl: request pin 10 (io10) for pio:10
- [ 3.810000] rt2880-pinmux pinctrl: request pin 0 (io0) for pio:0
- [ 3.820000] rt2880-pinmux pinctrl: request pin 8 (io8) for pio:8
- [ 3.820000] rt2880-pinmux pinctrl: request pin 9 (io9) for pio:9
- [ 3.830000] rt2880-pinmux pinctrl: request pin 14 (io14) for pio:14
- [ 3.830000] rt2880-pinmux pinctrl: request pin 12 (io12) for pio:12
- [ 3.830000] rt2880-pinmux pinctrl: request pin 13 (io13) for pio:13
- [ 4.250000] init: - preinit -
- [ 5.470000] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 5.660000] random: procd urandom read with 8 bits of entropy available
- [ 9.220000] jffs2: notice: (294) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 9.250000] mount_root: switching to jffs2 overlay
- [ 9.340000] procd: - early -
- [ 9.340000] procd: - watchdog -
- [ 10.400000] procd: - ubus -
- [ 11.420000] procd: - init -
- [ 13.180000] NET: Registered protocol family 10
- [ 13.210000] ip6_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.250000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
- [ 13.270000] Backport generated by backports.git backports-20150129-0-gdd4a670
- [ 13.290000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 13.320000] nf_conntrack version 0.5.0 (454 buckets, 1816 max)
- [ 13.420000] xt_time: kernel timezone is -0000
- [ 13.490000] cfg80211: Calling CRDA to update world regulatory domain
- [ 13.560000] cfg80211: World regulatory domain updated:
- [ 13.570000] cfg80211: DFS Master region: unset
- [ 13.570000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- [ 13.590000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- [ 13.610000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- [ 13.630000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- [ 13.650000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- [ 13.670000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
- [ 13.680000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- [ 13.700000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- [ 13.720000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- [ 13.830000] PPP generic driver version 2.4.2
- [ 13.840000] NET: Registered protocol family 24
- [ 13.910000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
- [ 13.930000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
- [ 13.950000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- [ 28.440000] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 28.460000] device eth0.1 entered promiscuous mode
- [ 28.480000] device eth0 entered promiscuous mode
- [ 28.510000] br-lan: port 1(eth0.1) entered forwarding state
- [ 28.520000] br-lan: port 1(eth0.1) entered forwarding state
- [ 28.630000] device eth0.2 entered promiscuous mode
- [ 28.660000] br-wan: port 1(eth0.2) entered forwarding state
- [ 28.670000] br-wan: port 1(eth0.2) entered forwarding state
- [ 30.520000] br-lan: port 1(eth0.1) entered forwarding state
- [ 30.670000] br-wan: port 1(eth0.2) entered forwarding state
- [ 34.340000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
- [ 34.360000] device wlan0-1 entered promiscuous mode
- [ 36.020000] ieee80211 phy0: rt2x00lib_rxdone: Error - Wrong frame size 0 max 3840
- [ 37.860000] ieee80211 phy0: rt2x00lib_rxdone: Error - Wrong frame size 0 max 3840
- [ 41.240000] ieee80211 phy0: rt2x00lib_rxdone: Error - Wrong frame size 0 max 3840
- [ 44.650000] device wlan0-2 entered promiscuous mode
- [ 44.670000] br-lan: port 3(wlan0-2) entered forwarding state
- [ 44.680000] br-lan: port 3(wlan0-2) entered forwarding state
- [ 44.690000] IPv6: ADDRCONF(NETDEV_UP): wlan0-2: link is not ready
- [ 44.710000] br-lan: port 3(wlan0-2) entered disabled state
- [ 45.210000] device wlan0-3 entered promiscuous mode
- [ 45.230000] br-lan: port 4(wlan0-3) entered forwarding state
- [ 45.240000] br-lan: port 4(wlan0-3) entered forwarding state
- [ 45.250000] IPv6: ADDRCONF(NETDEV_UP): wlan0-3: link is not ready
- [ 45.710000] br-lan: port 4(wlan0-3) entered disabled state
- [ 45.920000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- [ 47.690000] ieee80211 phy0: rt2x00lib_rxdone: Error - Wrong frame size 0 max 3840
- [ 48.090000] wlan0: authenticate with 84:d8:1b:8a:44:db
- [ 48.170000] wlan0: send auth to 84:d8:1b:8a:44:db (try 1/3)
- [ 48.180000] wlan0: authenticated
- [ 48.200000] wlan0: associate with 84:d8:1b:8a:44:db (try 1/3)
- [ 48.220000] wlan0: RX AssocResp from 84:d8:1b:8a:44:db (capab=0x1431 status=0 aid=3)
- [ 48.230000] wlan0: associated
- [ 48.240000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
- [ 49.020000] br-lan: port 2(wlan0-1) entered forwarding state
- [ 49.030000] br-lan: port 2(wlan0-1) entered forwarding state
- [ 49.040000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
- [ 49.880000] br-lan: port 3(wlan0-2) entered forwarding state
- [ 49.890000] br-lan: port 3(wlan0-2) entered forwarding state
- [ 49.900000] ------------[ cut here ]------------
- [ 49.910000] WARNING: CPU: 0 PID: 1032 at /home/buildbot/slave-local/ramips_rt305x/build/build_dir/target-mipsel_24kec+dsp_uClibc-0.9.33.2/linux-ramips_rt305x/compat-wireless-2015-03-09/drivers/net/wireless/rt2x00/rt2800lib.c:1095 rt2800_get_txwi_rxwi_size+0x19c/0x268 [rt2800lib]()
- [ 49.960000] Modules linked in: rt2800soc rt2800mmio rt2800lib pppoe ppp_async iptable_nat rt2x00soc rt2x00mmio rt2x00lib pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc nf_reject_ipv4 nf_nat_masquerade_ipv4 nf_nat_ftp nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack_ftp nf_conntrack iptable_raw iptable_mangle iptable_filter ip_tables crc_itu_t crc_ccitt compat ledtrig_usbdev ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables ipv6 eeprom_93cx6 arc4 crypto_blkcipher leds_gpio dwc2_platform dwc2 gpio_button_hotplug usbcore nls_base usb_common
- [ 50.110000] CPU: 0 PID: 1032 Comm: kworker/0:2 Not tainted 3.18.23 #1
- [ 50.120000] Workqueue: events linkwatch_event
- [ 50.130000] Stack : 00000001 00000000 80e81900 802a40c8 80d13c38 80d0402c 00000447 80e66b40
- [ 50.130000] 00000008 0000001c 00000001 80046f0c 00000408 80039b20 80eb7790 80e66b40
- [ 50.130000] 802c7a38 80fe5ac4 80fe5ac4 80046f0c 00000003 80037510 00000447 00000128
- [ 50.130000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
- [ 50.130000] 6e657665 00007374 00000000 00000000 00000000 00000000 81805b00 81047700
- [ 50.130000] ...
- [ 50.210000] Call Trace:
- [ 50.210000] [<80013cf8>] show_stack+0x50/0x84
- [ 50.220000] [<80023fc0>] warn_slowpath_common+0x84/0xb4
- [ 50.230000] [<80024078>] warn_slowpath_null+0x18/0x24
- [ 50.240000] [<80d0402c>] rt2800_get_txwi_rxwi_size+0x19c/0x268 [rt2800lib]
- [ 50.250000]
- [ 50.260000] ---[ end trace f7f7673da678992b ]---
- [ 50.270000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-2: link becomes ready
- [ 51.030000] br-lan: port 2(wlan0-1) entered forwarding state
- [ 51.230000] br-lan: port 4(wlan0-3) entered forwarding state
- [ 51.240000] br-lan: port 4(wlan0-3) entered forwarding state
- [ 51.260000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-3: link becomes ready
- [ 51.890000] br-lan: port 3(wlan0-2) entered forwarding state
- [ 53.240000] br-lan: port 4(wlan0-3) entered forwarding state
- [ 57.130000] random: nonblocking pool is initialized
- [ 1694.010000] br-lan: port 2(wlan0-1) entered disabled state
- [ 1694.020000] br-lan: port 3(wlan0-2) entered disabled state
- [ 1694.040000] br-lan: port 4(wlan0-3) entered disabled state
- [ 1694.300000] ieee80211 phy0: rt2x00lib_rxdone: Error - Wrong frame size 0 max 3840
- [ 1694.410000] ieee80211 phy0: rt2x00lib_rxdone: Error - Wrong frame size 0 max 3840
- [ 1694.620000] wlan0: authenticate with 84:d8:1b:8a:44:db
- [ 1694.700000] wlan0: send auth to 84:d8:1b:8a:44:db (try 1/3)
- [ 1694.710000] wlan0: authenticated
- [ 1694.730000] wlan0: associate with 84:d8:1b:8a:44:db (try 1/3)
- [ 1694.750000] wlan0: RX AssocResp from 84:d8:1b:8a:44:db (capab=0x1431 status=0 aid=2)
- [ 1694.770000] wlan0: associated
- [ 1695.510000] br-lan: port 2(wlan0-1) entered forwarding state
- [ 1695.530000] br-lan: port 2(wlan0-1) entered forwarding state
- [ 1695.910000] br-lan: port 3(wlan0-2) entered forwarding state
- [ 1695.920000] br-lan: port 3(wlan0-2) entered forwarding state
- [ 1696.290000] br-lan: port 4(wlan0-3) entered forwarding state
- [ 1696.300000] br-lan: port 4(wlan0-3) entered forwarding state
- [ 1697.530000] br-lan: port 2(wlan0-1) entered forwarding state
- [ 1697.920000] br-lan: port 3(wlan0-2) entered forwarding state
- [ 1698.300000] br-lan: port 4(wlan0-3) entered forwarding state
- [23266.000000] br-lan: port 2(wlan0-1) entered disabled state
- [23266.010000] br-lan: port 3(wlan0-2) entered disabled state
- [23266.030000] br-lan: port 4(wlan0-3) entered disabled state
- [23266.410000] ieee80211 phy0: rt2x00lib_rxdone: Error - Wrong frame size 0 max 3840
- [23266.610000] wlan0: authenticate with 84:d8:1b:8a:44:db
- [23266.690000] wlan0: send auth to 84:d8:1b:8a:44:db (try 1/3)
- [23266.700000] wlan0: authenticated
- [23266.720000] wlan0: associate with 84:d8:1b:8a:44:db (try 1/3)
- [23266.840000] wlan0: associate with 84:d8:1b:8a:44:db (try 2/3)
- [23266.870000] wlan0: RX AssocResp from 84:d8:1b:8a:44:db (capab=0x1431 status=0 aid=2)
- [23266.880000] wlan0: associated
- [23267.600000] br-lan: port 2(wlan0-1) entered forwarding state
- [23267.610000] br-lan: port 2(wlan0-1) entered forwarding state
- [23267.980000] br-lan: port 3(wlan0-2) entered forwarding state
- [23267.990000] br-lan: port 3(wlan0-2) entered forwarding state
- [23268.360000] br-lan: port 4(wlan0-3) entered forwarding state
- [23268.370000] br-lan: port 4(wlan0-3) entered forwarding state
- [23269.610000] br-lan: port 2(wlan0-1) entered forwarding state
- [23269.990000] br-lan: port 3(wlan0-2) entered forwarding state
- [23270.370000] br-lan: port 4(wlan0-3) entered forwarding state
- [69250.030000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.040000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.060000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.080000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.100000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.120000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.140000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.160000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.180000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.200000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.210000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.230000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.250000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.270000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.290000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.310000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.330000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.350000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.370000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.380000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.400000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.420000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.440000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.460000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.480000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.500000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.740000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.760000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.780000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.800000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.820000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.840000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.850000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.870000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.890000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.910000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.930000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.950000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.970000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69250.990000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.010000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.020000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.040000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.060000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.080000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.100000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.120000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.140000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.160000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.170000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.190000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.210000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.230000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.250000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.270000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.290000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.310000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.330000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.340000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.360000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.380000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.400000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.420000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.440000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [69251.460000] ieee80211 phy0: rt2x00queue_write_tx_frame: Error - Dropping frame due to full tx queue 2
- [75557.960000] rt305x-esw 10110000.esw: link changed 0x08
- [75566.910000] rt305x-esw 10110000.esw: link changed 0x00
- [75644.350000] rt305x-esw 10110000.esw: link changed 0x08
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement