API tools faq
paste
Advertisement
Guest User

Untitled

a guest
Jun 22nd, 2020
24
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 29.90 KB | None | 0 0
raw download clone embed print report
  1. # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
  2. # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
  3. ## Robot module configurations : general handling of movement G-codes and slicing into moves
  4.  
  5. # Basic motion configuration
  6. default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves
  7. default_seek_rate 4000 # Default speed (mm/minute) for G0 moves
  8. mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable
  9. #mm_per_line_segment 5 # Cut lines into segments this size
  10. mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
  11. # note it is invalid for both the above be 0
  12. # if both are used, will use largest segment length based on radius
  13.  
  14. # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
  15. # See http://smoothieware.org/stepper-motors
  16. alpha_steps_per_mm 320 # Steps per mm for alpha ( X ) stepper
  17. beta_steps_per_mm 320 # Steps per mm for beta ( Y ) stepper
  18. gamma_steps_per_mm 215 # Steps per mm for gamma ( Z ) stepper
  19.  
  20. # Planner module configuration : Look-ahead and acceleration configuration
  21. # See http://smoothieware.org/motion-control
  22. acceleration 3000 # Acceleration in mm/second/second.
  23. #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
  24. junction_deviation 0.04 # See http://smoothieware.org/motion-control#junction-deviation
  25. #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
  26.  
  27. # Cartesian axis speed limits
  28. x_axis_max_speed 4500 # Maximum speed in mm/min
  29. y_axis_max_speed 4500 # Maximum speed in mm/min
  30. z_axis_max_speed 4000 # Maximum speed in mm/min
  31.  
  32. # Stepper module configuration
  33. # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
  34. # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
  35. microseconds_per_step_pulse 3 # Duration of step pulses to stepper drivers, in microseconds
  36. bse_stepping_frequency 100000 # Base frequency for stepping
  37. alpha_step_pin 2.0 # Pin for alpha stepper step signal
  38. alpha_dir_pin 0.5! # Pin for alpha stepper direction, add '!' to reverse direction
  39. alpha_en_pin 0.4 # Pin for alpha enable pin
  40. alpha_current 1.5 # X stepper motor current
  41. alpha_max_rate 12000.0 # Maximum rate in mm/min
  42.  
  43. beta_step_pin 2.1 # Pin for beta stepper step signal
  44. beta_dir_pin 0.11! # Pin for beta stepper direction, add '!' to reverse direction
  45. beta_en_pin 0.10 # Pin for beta enable
  46. beta_current 1.5 # Y stepper motor current
  47. beta_max_rate 12000.0 # Maxmimum rate in mm/min
  48.  
  49. gamma_step_pin 2.2 # Pin for gamma stepper step signal
  50. gamma_dir_pin 0.20! # Pin for gamma stepper direction, add '!' to reverse direction
  51. gamma_en_pin 0.19 # Pin for gamma enable
  52. gamma_current 1.5 # Z stepper motor current
  53. gamma_max_rate 1000.0 # Maximum rate in mm/min
  54.  
  55. ## Extruder module configuration
  56. # See http://smoothieware.org/extruder
  57. extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  58. extruder.hotend.steps_per_mm 6009.52 # Steps per mm for extruder stepper
  59. extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  60. extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
  61. extruder.hotend.max_speed 15 # Maximum speed in mm/s
  62.  
  63. extruder.hotend.step_pin 2.3 # Pin for extruder step signal
  64. extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal ( add '!' to reverse direction )
  65. extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
  66.  
  67. # Extruder offset
  68. #extruder.hotend.x_offset 0 # X offset from origin in mm
  69. #extruder.hotend.y_offset 0 # Y offset from origin in mm
  70. #extruder.hotend.z_offset 0 # Z offset from origin in mm
  71.  
  72. # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
  73. #extruder.hotend.retract_length 3 # Retract length in mm
  74. #extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec
  75. #extruder.hotend.retract_recover_length 0 # Additional length for recover
  76. #extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
  77. #extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
  78. #extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
  79.  
  80. delta_current 1.5 # First extruder stepper motor current
  81.  
  82. # Second extruder module configuration
  83. extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
  84. extruder.hotend2.steps_per_mm 6009.52 # Steps per mm for extruder stepper
  85. extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
  86. extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
  87. extruder.hotend2.max_speed 50 # mm/s
  88.  
  89. extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
  90. extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
  91. extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
  92.  
  93. #extruder.hotend2.x_offset 0 # x offset from origin in mm
  94. #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
  95. #extruder.hotend2.z_offset 0 # z offset from origin in mm
  96.  
  97. #epsilon_current 1.5 # Second extruder stepper motor current
  98.  
  99.  
  100. ## Temperature control configuration
  101. # See http://smoothieware.org/temperaturecontrol
  102.  
  103. # First hotend configuration
  104. temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
  105. temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
  106. temperature_control.hotend.heater_pin 1.30 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  107. temperature_control.hotend.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#toc5
  108. #temperature_control.hotend.beta 4066 # Or set the beta value
  109. temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
  110. temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  111. temperature_control.hotend.designator T # Designator letter for this module
  112. temperature_control.hotend.max_temp 80 # Set maximum temperature - Will prevent heating above 300 by default
  113. #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  114. temperature_control.hotend.pwm_frequency 20 # PWM frequency of extruder 1
  115.  
  116. # Safety control is enabled by default and can be overidden here, the values show the defaults
  117. # See http://smoothieware.org/temperaturecontrol#runaway
  118. temperature_control.hotend.runaway_heating_timeout 1000 # How long it can take to heat up, max is 2040 seconds.
  119. temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  120. temperature_control.hotend.runaway_range 50 # How far from the set temperature it can wander, max setting is 63°C
  121.  
  122. # PID configuration
  123. # See http://smoothieware.org/temperaturecontrol#pid
  124. temperature_control.hotend.p_factor 13.7 # P ( proportional ) factor
  125. temperature_control.hotend.i_factor 0.097 # I ( integral ) factor
  126. temperature_control.hotend.d_factor 24 # D ( derivative ) factor
  127.  
  128.  
  129.  
  130. # Second hotend configuration
  131. temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
  132. temperature_control.hotend2.thermistor_pin 0.24 # Pin for the thermistor to read
  133. temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
  134. temperature_control.hotend2.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  135. #temperature_control.hotend2.beta 4066 # or set the beta value
  136. temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
  137. temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  138. temperature_control.hotend2.designator T1 # Designator letter for this module
  139. temperature_control.hotend2.max_temp 80 # Set maximum temperature - Will prevent heating above 300 by default
  140. #temperature_control.hotend2.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  141. temperature_control.hotend2.pwm_frequency 20 # PWM frequency of extruder 2
  142.  
  143. # Safety control is enabled by default and can be overidden here, the values show the defaults
  144. # See http://smoothieware.org/temperaturecontrol#runaway
  145. #temperature_control.hotend2.runaway_heating_timeout 1000 # How long it can take to heat up, max is 2040 seconds.
  146. #temperature_control.hotend2.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
  147. #temperature_control.hotend2.runaway_range 50 # How far from the set temperature it can wander, max setting is 63°C
  148.  
  149. # PID configuration extruder 2
  150. temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor
  151. temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor
  152. temperature_control.hotend2.d_factor 24 # D ( derivative ) factor
  153.  
  154. # Third hotend configuration
  155. temperature_control.hotend3.enable true # Whether to activate this ( "hotend" ) module at all.
  156. temperature_control.hotend3.thermistor_pin 0.25 # Pin for the thermistor to read
  157. temperature_control.hotend3.heater_pin 1.31 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
  158. temperature_control.hotend3.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#toc5
  159. #temperature_control.hotend3.beta 4066 # Or set the beta value
  160. temperature_control.hotend3.set_m_code 104 # M-code to set the temperature for this module
  161. temperature_control.hotend3.set_and_wait_m_code 109 # M-code to set-and-wait for this module
  162. temperature_control.hotend3.designator T2 # Designator letter for this module
  163. temperature_control.hotend3.max_temp 80 # Set maximum temperature - Will prevent heating above 300 by default
  164. #temperature_control.hotend3.min_temp 0 # Set minimum temperature - Will prevent heating below if set
  165. temperature_control.hotend3.pwm_frequency 20 # PWM frequency of extruder 3
  166. temperature_control.hotend3.bang_bang true # Set to true to use bang bang control rather than PID
  167. temperature_control.hotend3.hysteresis 5.0 # Set to the temperature in degrees C to use as hysteresis
  168.  
  169.  
  170. temperature_control.bed.enable true # Whether to activate this ( "hotend" ) module at all.
  171. temperature_control.bed.thermistor_pin 0.26 # Pin for the thermistor to read
  172. temperature_control.bed.heater_pin 2.5 # Pin that controls the heater
  173. temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
  174. #temperature_control.bed.beta 3974 # Or set the beta value
  175. temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
  176. temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
  177. temperature_control.bed.designator B # Designator letter for this module
  178.  
  179. # Bang-bang ( simplified ) control
  180. # See http://smoothieware.org/temperaturecontrol#bang-bang
  181. temperature_control.bed.bang_bang true # Set to true to use bang bang control rather than PID
  182. temperature_control.bed.hysteresis 5.0 # Set to the temperature in degrees C to use as hysteresis
  183.  
  184. ## Switch modules
  185. # See http://smoothieware.org/switch
  186.  
  187. # Switch module for fan control
  188. #switch.fan.enable true # Enable this module
  189. #switch.fan.input_on_command M106 # Command that will turn this switch on
  190. #switch.fan.input_off_command M107 # Command that will turn this switch off
  191. #switch.fan.output_pin 2.6 # Pin this module controls
  192. #switch.fan.output_type pwm # PWM output settable with S parameter in the input_on_comand
  193. #switch.fan.max_pwm 255 # Set max pwm for the pin default is 255
  194.  
  195. #switch.misc.enable true # Enable this module
  196. #switch.misc.input_on_command M42 # Command that will turn this switch on
  197. #switch.misc.input_off_command M43 # Command that will turn this switch off
  198. #switch.misc.output_pin 2.4 # Pin this module controls
  199. #switch.misc.output_type digital # Digital means this is just an on or off pin
  200.  
  201. switch.contactor.enable true # Enable this module
  202. switch.contactor.input_on_command M42 # Command that will turn this switch on
  203. switch.contactor.input_off_command halt # Command that will turn this switch off
  204. switch.contactor.output_pin 1.22 # Pin this module controls
  205. switch.contactor.output_type digital # Digital means this is just an on or off pin
  206. switch.contactor.startup_state true #Startup state of the switch
  207.  
  208. #switch.bltouch.enable true #
  209. #switch.bltouch.output_pin 1.22 # sw pwm can use any digital pin
  210. #switch.bltouch.input_on_command M280 #
  211. #switch.bltouch.input_off_command M281 #
  212. #switch.bltouch.output_type swpwm # sw pwm must be low frequency
  213. #switch.bltouch.pwm_period_ms 20 # 50Hz
  214. #switch.bltouch.startup_state false # start up in the stow state
  215. #switch.bltouch.startup_value 7.43 # On boot it will go into stow mode, also set with the M281
  216. #switch.bltouch.default_on_value 3.3 # if M280 is issued without S this is the value it will set it to
  217.  
  218.  
  219. ## Temperatureswitch
  220. # See http://smoothieware.org/temperatureswitch
  221. # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
  222. # Useful to turn on a fan or water pump to cool the hotend
  223. temperatureswitch.hotfan.enable true #
  224. temperatureswitch.hotfan.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
  225. temperatureswitch.hotfan.switch contactor # select which switch to use, matches the name of the defined switch
  226. temperatureswitch.hotfan.threshold_temp 120 # temperature to turn on (if rising) or off the switch
  227. temperatureswitch.hotfan.heatup_poll .5 # poll heatup at 15 sec intervals
  228. temperatureswitch.hotfan.cooldown_poll 60 # poll cooldown at 60 sec intervals
  229. temperatureswitch.hotfan.trigger rising
  230. temperatureswitch.hotfan.inverted true #will turn switch off when temp > target and vice versa when set to true
  231.  
  232. ## Endstops
  233. # See http://smoothieware.org/endstops
  234. endstops_enable true # The endstop module is enabled by default and can be disabled here
  235. #corexy_homing false # Set to true if homing on a hbot or corexy
  236. alpha_min_endstop 1.24!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  237. #alpha_max_endstop 1.25^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  238. alpha_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  239. alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
  240. alpha_max 215 # This gets loaded as the current position after homing when home_to_max is set
  241. beta_min_endstop 1.26!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  242. #beta_max_endstop 1.27^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  243. beta_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  244. beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
  245. beta_max 215 # This gets loaded as the current position after homing when home_to_max is set
  246. gamma_min_endstop 1.28!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
  247. #gamma_max_endstop 1.29^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
  248. gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
  249. gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
  250. gamma_max 315 # This gets loaded as the current position after homing when home_to_max is set
  251.  
  252. alpha_max_travel 210 # Max travel in mm for alpha/X axis when homing
  253. beta_max_travel 210 # Max travel in mm for beta/Y axis when homing
  254. gamma_max_travel 310 # Max travel in mm for gamma/Z axis when homing
  255.  
  256. # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
  257. #alpha_limit_enable false # Set to true to enable X min and max limit switches
  258. #beta_limit_enable false # Set to true to enable Y min and max limit switches
  259. #gamma_limit_enable false # Set to true to enable Z min and max limit switches
  260.  
  261. # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
  262. alpha_fast_homing_rate_mm_s 30 # Alpha/X fast homing feedrate in mm/second
  263. alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
  264. beta_fast_homing_rate_mm_s 30 # Beta/Y fast homing feedrate in mm/second
  265. beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
  266. gamma_fast_homing_rate_mm_s 15 # Gamma/Z fast homing feedrate in mm/second
  267. gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
  268.  
  269. alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
  270. beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
  271. gamma_homing_retract_mm 1 # Distance to retract from the endstop after it is hit for gamma/Z
  272.  
  273. # Optional order in which axis will home, default is they all home at the same time,
  274. # If this is set it will force each axis to home one at a time in the specified order
  275. #homing_order YXZ # X axis followed by Y then Z last
  276. #move_to_origin_after_home false # Move XY to 0,0 after homing
  277. #endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
  278. #endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
  279. #home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
  280.  
  281. # End of endstop config
  282. # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
  283. #include abc-endstop.config
  284.  
  285. ## Z-probe
  286. # See http://smoothieware.org/zprobe
  287. zprobe.enable false # Set to true to enable a zprobe
  288. zprobe.probe_pin 1.28!^ # Pin probe is attached to, if NC remove the !
  289. zprobe.slow_feedrate 5 # Mm/sec probe feed rate
  290. #zprobe.debounce_ms 1 # Set if noisy
  291. zprobe.fast_feedrate 100 # Move feedrate mm/sec
  292. zprobe.probe_height 5 # How much above bed to start probe
  293. #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
  294.  
  295. # Levelling strategy
  296. # Example for 3-point levelling strategy, see wiki documentation for other strategies
  297. #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
  298. #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
  299. #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
  300. #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
  301. #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
  302. #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
  303. #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
  304. #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
  305.  
  306. ## Panel
  307. # See http://smoothieware.org/panel
  308. # Please find your panel on the wiki and copy/paste the right configuration here
  309. panel.enable false # Set to true to enable the panel code
  310.  
  311. # Example for reprap discount GLCD
  312. # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
  313. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
  314. #panel.lcd reprap_discount_glcd #
  315. #panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
  316. #panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4
  317. #panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3
  318. #panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5
  319. #panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2
  320. #panel.buzz_pin 1.31 # Pin for buzzer ; GLCD EXP1 Pin 1
  321. #panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8
  322.  
  323. panel.menu_offset 0 # Some panels will need 1 here
  324.  
  325. panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
  326. panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
  327. panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
  328.  
  329. panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
  330. panel.bed_temperature 60 # Temp to set bed when preheat is selected
  331.  
  332. ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
  333. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
  334. custom_menu.power_on.enable false #
  335. custom_menu.power_on.name Power_on #
  336. custom_menu.power_on.command M80 #
  337.  
  338. custom_menu.power_off.enable true #
  339. custom_menu.power_off.name Power_off #
  340. custom_menu.power_off.command M81 #
  341.  
  342.  
  343. ## Network settings
  344. # See http://smoothieware.org/network
  345. network.enable false # Enable the ethernet network services
  346. network.webserver.enable true # Enable the webserver
  347. network.telnet.enable true # Enable the telnet server
  348. network.ip_address auto # Use dhcp to get ip address
  349. # Uncomment the 3 below to manually setup ip address
  350. #network.ip_address 192.168.3.222 # The IP address
  351. #network.ip_mask 255.255.255.0 # The ip mask
  352. #network.ip_gateway 192.168.3.1 # The gateway address
  353. #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
  354.  
  355. ## System configuration
  356. # Serial communications configuration ( baud rate defaults to 9600 if undefined )
  357. # For communication over the UART port, *not* the USB/Serial port
  358. uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
  359.  
  360. second_usb_serial_enable true # This enables a second USB serial port
  361. #leds_disable true # Disable using leds after config loaded
  362. #play_led_disable true # Disable the play led
  363.  
  364. # Kill button maybe assigned to a different pin, set to the onboard pin by default
  365. # See http://smoothieware.org/killbutton
  366. kill_button_enable true # Set to true to enable a kill button
  367. kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
  368.  
  369. #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
  370. #dfu_enable false # For linux developers, set to true to enable DFU
  371.  
  372. # Only needed on a smoothieboard
  373. # See http://smoothieware.org/currentcontrol
  374. currentcontrol_module_enable true # Control stepper motor current via the configuration file
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!