SHARE
TWEET

U-boot

a guest Sep 14th, 2015 151 Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. ROM VER:xxxxxldxysedq
  2. U-Boot 2013.10-openwrt4 (Sep 12 2015 - 14:59:11) VGV7510KW22
  3.  
  4. Board: Arcadyan VGV7510KW22
  5. SoC:   Lantiq VRX288 v1.2
  6. CPU:   500 MHz
  7. IO:    250 MHz
  8. BUS:   250 MHz
  9. BOOT:  NOR
  10. DRAM:  64 MiB
  11. Flash: 16 MiB
  12. *** Warning - bad CRC, using default environment
  13.  
  14. In:    serial
  15. Out:   serial
  16. Err:   serial
  17. SPI:   ready
  18. Net:   ltq-eth
  19. Hit any key to stop autoboot:  2  1  0
  20. ## Booting kernel from Legacy Image at b0080000 ...
  21.    Image Name:   MIPS OpenWrt Linux-3.18.21
  22.    Created:      2015-09-04  14:39:09 UTC
  23.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  24.    Data Size:    1543521 Bytes = 1.5 MiB
  25.    Load Address: 80002000
  26.    Entry Point:  80002000
  27.    Verifying Checksum ... OK
  28.    Uncompressing Kernel Image ... OK
  29.  
  30. Starting kernel ...
  31.  
  32. [    0.000000] Linux version 3.18.21 (chm@H710-SF) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46781) ) #1 Fri Sep 4 16:38:26 CEST 2015
  33.  
  34. [    0.000000] SoC: VR9 rev 1.2
  35.  
  36. [    0.000000] bootconsole [early0] enabled
  37.  
  38. [    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
  39.  
  40. [    0.000000] MIPS: machine is VGV7510KW22 - o2 Box 6431
  41.  
  42. [    0.000000] Determined physical RAM map:
  43.  
  44. [    0.000000]  memory: 04000000 @ 00000000 (usable)
  45.  
  46. [    0.000000] Initrd not found or empty - disabling initrd
  47.  
  48. [    0.000000] Zone ranges:
  49.  
  50. [    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
  51.  
  52. [    0.000000] Movable zone start for each node
  53.  
  54. [    0.000000] Early memory node ranges
  55.  
  56. [    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
  57.  
  58. [    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
  59.  
  60. [    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  61.  
  62. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  63.  
  64. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
  65.  
  66. [    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
  67.  
  68. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  69.  
  70. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  71.  
  72. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  73.  
  74. [    0.000000] Writing ErrCtl register=00061370
  75.  
  76. [    0.000000] Readback ErrCtl register=00061370
  77.  
  78. [    0.000000] Memory: 60064K/65536K available (3349K kernel code, 146K rwdata, 936K rodata, 156K init, 205K bss, 5472K reserved)
  79.  
  80. [    0.000000] NR_IRQS:256
  81.  
  82. [    0.000000] CPU Clock: 500MHz
  83.  
  84. [    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
  85.  
  86. [    0.032000] pid_max: default: 32768 minimum: 301
  87.  
  88. [    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  89.  
  90. [    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  91.  
  92. [    0.044000] pinctrl core: initialized pinctrl subsystem
  93.  
  94. [    0.048000] NET: Registered protocol family 16
  95.  
  96. [    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
  97.  
  98. [    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
  99.  
  100. [    0.164000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
  101.  
  102. [    0.168000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
  103.  
  104. [    0.172000]  MEM 0x0000000018000000..0x0000000019ffffff
  105.  
  106. [    0.176000]   IO 0x000000001ae00000..0x000000001affffff
  107.  
  108. [    0.200000] gpio-stp-xway 1e100bb0.stp: Init done
  109.  
  110. [    0.204000] usbcore: registered new interface driver usbfs
  111.  
  112. [    0.208000] usbcore: registered new interface driver hub
  113.  
  114. [    0.212000] usbcore: registered new device driver usb
  115.  
  116. [    0.216000] PCI host bridge to bus 0000:00
  117.  
  118. [    0.220000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
  119.  
  120. [    0.224000] pci_bus 0000:00: root bus resource [io  0xffffffff]
  121.  
  122. [    0.228000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  123.  
  124. [    0.232000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
  125.  
  126. [    0.236000] Switched to clocksource MIPS
  127.  
  128. [    0.240000] NET: Registered protocol family 2
  129.  
  130. [    0.244000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  131.  
  132. [    0.252000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  133.  
  134. [    0.260000] TCP: Hash tables configured (established 1024 bind 1024)
  135.  
  136. [    0.264000] TCP: reno registered
  137.  
  138. [    0.268000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  139.  
  140. [    0.272000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  141.  
  142. [    0.280000] NET: Registered protocol family 1
  143.  
  144. [    0.284000] gptu: totally 6 16-bit timers/counters
  145.  
  146. [    0.288000] gptu: misc_register on minor 63
  147.  
  148. [    0.296000] gptu: succeeded to request irq 126
  149.  
  150. [    0.300000] gptu: succeeded to request irq 127
  151.  
  152. [    0.304000] gptu: succeeded to request irq 128
  153.  
  154. [    0.308000] gptu: succeeded to request irq 129
  155.  
  156. [    0.312000] gptu: succeeded to request irq 130
  157.  
  158. [    0.316000] gptu: succeeded to request irq 131
  159.  
  160. [    0.320000] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
  161.  
  162. [    0.328000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy22f_a2x.bin
  163.  
  164. [    0.336000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 3900000
  165.  
  166. [    0.340000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 3900000
  167.  
  168. [    0.448000] futex hash table entries: 256 (order: -1, 3072 bytes)
  169.  
  170. [    0.456000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  171.  
  172. [    0.464000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  173.  
  174. [    0.472000] msgmni has been set to 117
  175.  
  176. [    0.476000] io scheduler noop registered
  177.  
  178. [    0.480000] io scheduler deadline registered (default)
  179.  
  180. [    0.488000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
  181.  
  182. [    0.496000] console [ttyLTQ0] enabled
  183. [    0.496000] console [ttyLTQ0] enabled
  184.  
  185. [    0.504000] bootconsole [early0] disabled
  186. [    0.504000] bootconsole [early0] disabled
  187.  
  188. [    0.512000] lantiq nor flash device: 01000000 at 10000000
  189. [    0.516000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
  190. [    0.528000] Amd/Fujitsu Extended Query Table at 0x0040
  191. [    0.532000]   Amd/Fujitsu Extended Query version 1.3.
  192. [    0.536000] number of CFI chips: 1
  193. [    0.540000] 8 ofpart partitions found on MTD device ltq_nor
  194. [    0.544000] Creating 8 MTD partitions on "ltq_nor":
  195. [    0.552000] 0x000000fe0000-0x000001000000 : "board_config"
  196. [    0.556000] 0x000000000000-0x000000040000 : "Boot"
  197. [    0.560000] 0x000000040000-0x000000080000 : "Configuration"
  198. [    0.568000] 0x000000080000-0x0000000a0000 : "Certificate"
  199. [    0.572000] 0x0000000a0000-0x0000000c0000 : "Special_Area"
  200. [    0.576000] 0x0000000c0000-0x0000000e0000 : "Primary_Setting"
  201. [    0.584000] 0x0000000e0000-0x000000860000 : "firmware"
  202. [    0.604000] 0x000000860000-0x000000fe0000 : "Code_Image_1"
  203. [    0.712000] libphy: lantiq,xrx200-mdio: probed
  204. [    0.808000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:11, irq=-1)
  205. [    0.876000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:12, irq=-1)
  206. [    0.944000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:13, irq=-1)
  207. [    1.012000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4] (phy_addr=0:14, irq=-1)
  208. [    1.020000] wdt 1f8803f0.watchdog: Init done
  209. [    1.024000] TCP: cubic registered
  210. [    1.024000] NET: Registered protocol family 17
  211. [    1.032000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
  212. [    1.044000] 8021q: 802.1Q VLAN Support v1.8
  213. [    1.052000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
  214. [    1.056000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
  215. [    1.064000] Please append a correct "root=" boot option; here are the available partitions:
  216. [    1.072000] 1f00             128 mtdblock0  (driver?)
  217. [    1.076000] 1f01             256 mtdblock1  (driver?)
  218. [    1.084000] 1f02             256 mtdblock2  (driver?)
  219. [    1.088000] 1f03             128 mtdblock3  (driver?)
  220. [    1.092000] 1f04             128 mtdblock4  (driver?)
  221. [    1.096000] 1f05             128 mtdblock5  (driver?)
  222. [    1.104000] 1f06            7680 mtdblock6  (driver?)
  223. [    1.108000] 1f07            7680 mtdblock7  (driver?)
  224. [    1.112000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
  225. [    1.112000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
  226. [   33.092000] random: nonblocking pool is initialized
RAW Paste Data
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy. OK, I Understand
 
Top