USB and LAN does not work at all due to EEPROM failure

[0000.301] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses.
[0000.310] I> MB1 (prd-version: 1.5.1.7-t194-41334769-98030a79)
[0000.315] I> Boot-mode: Coldboot
[0000.318] I> Chip revision : A02P
[0000.321] I> Bootrom patch version : 15 (correctly patched)
[0000.326] I> ATE fuse revision : 0x200
[0000.330] I> Ram repair fuse : 0x0
[0000.333] I> Ram Code : 0x2
[0000.335] I> rst_source : 0x0
[0000.338] I> rst_level : 0x0
[0000.342] I> Boot-device: eMMC
[0000.357] I> sdmmc DDR50 mode
[0000.361] W> No valid slot number is found in scratch register
[0000.366] W> Return default slot: _a
[0000.370] I> Active Boot chain : 0
[0000.373] I> Boot-device: eMMC
[0000.376] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT.
[0000.384] I> Temperature = 27000
[0000.387] W> Skipping boost for clk: BPMP_CPU_NIC
[0000.392] W> Skipping boost for clk: BPMP_APB
[0000.396] W> Skipping boost for clk: AXI_CBB
[0000.400] W> Skipping boost for clk: AON_CPU_NIC
[0000.404] W> Skipping boost for clk: CAN1
[0000.407] W> Skipping boost for clk: CAN2
[0000.412] I> Boot-device: eMMC
[0000.415] I> Boot-device: eMMC
[0000.424] I> Sdmmc: HS400 mode enabled
[0000.429] I> ECC region[0]: Start:0x0, End:0x0
[0000.433] I> ECC region[1]: Start:0x0, End:0x0
[0000.437] I> ECC region[2]: Start:0x0, End:0x0
[0000.441] I> ECC region[3]: Start:0x0, End:0x0
[0000.445] I> ECC region[4]: Start:0x0, End:0x0
[0000.449] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000
[0000.455] I> Non-ECC region[1]: Start:0x0, End:0x0
[0000.459] I> Non-ECC region[2]: Start:0x0, End:0x0
[0000.464] I> Non-ECC region[3]: Start:0x0, End:0x0
[0000.468] I> Non-ECC region[4]: Start:0x0, End:0x0
[0000.474] E> FAILED: Thermal config
[0000.481] E> FAILED: MEMIO rail config
[0000.499] I> Boot-device: eMMC
[0000.509] I> sdmmc bdev is already initialized
[0000.581] I> MB1 done

����main enter
SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21
HW Function test
Start Scheduler.
in late init
��
  [0000.590] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-938a8cd8)
[0000.591] I> DMA Heap @ [0x526fa000 - 0x52ffa000]
[0000.591] I> Default Heap @ [0xd486400 - 0xd48a400]
[0000.592] E> DEVICE_PROD: Invalid value data = 70020000, size = 0.
[0000.598] W> device prod register failed
[0000.602] I> Boot-device: eMMC
[0000.604] I> Boot_device: SDMMC_BOOT instance: 3
[0000.610] I> sdmmc-3 params source = boot args
[0000.613] I> sdmmc bdev is already initialized
[0000.617] I> sdmmc-3 params source = boot args
[0000.626] I> Found 17 partitions in SDMMC_BOOT (instance 3)
[0000.632] I> Found 42 partitions in SDMMC_USER (instance 3)
[0000.633] W> No valid slot number is found in scratch register
[0000.638] W> Return default slot: _a
[0000.642] I> Active Boot chain : 0
[0000.645] I> parsing oem signed section of bpmp-fw header done
[0000.651] I> bpmp-fw binary init read from storage
[0000.656] I> oem authentication of bpmp-fw header done
[0000.662] I> bpmp-fw binary done read from storage
[0000.665] I> bpmp-fw: Authentication init Done
[0000.670] I> parsing oem signed section of cpubl header done
[0000.675] I> cpubl binary init read from storage
[0000.679] I> bpmp-fw: Authentication Finalize Done
[0000.684] I> oem authentication of cpubl header done
[0000.689] I> cpubl binary done read from storage
[0000.693] I> cpubl: Authentication init Done
[0000.698] I> parsing oem signed section of rce header done
[0000.703] I> rce binary init read from storage
[0000.707] I> Relocating BR-BCT
[0000.710] I> cpubl: Authentication Finalize Done
[0000.714] I> oem authentication of rce header done
[0000.719] I> rce binary done read from storage
[0000.723] I> rce: Authentication init Done
[0000.728] I> parsing oem signed section of ape header done
[0000.732] I> ape binary init read from storage
[0000.737] I> rce: Authentication Finalize Done
[0000.741] I> oem authentication of ape header done
[0000.746] I> ape binary done read from storage
[0000.750] I> ape: Authentication init Done
[0000.755] I> parsing oem signed section of tos header done
[0000.759] I> tos binary init read from storage
[0000.764] I> ape: Authentication Finalize Done
[0000.768] I> oem authentication of tos header done
[0000.772] I> tos binary done read from storage
[0000.777] I> tos: Authentication init Done
[0000.781] I> parsing oem signed section of bpmp-fw-dtb header done
[0000.787] I> bpmp-fw-dtb binary init read from storage
[0000.792] I> tos: Authentication Finalize Done
[0000.798] I> oem authentication of bpmp-fw-dtb header done
[0000.804] I> bpmp-fw-dtb binary done read from storage
[0000.806] I> bpmp-fw-dtb: Authentication init Done
[0000.811] I> parsing oem signed section of cpubl-dtb header done
[0000.817] I> cpubl-dtb binary init read from storage
[0000.822] I> bpmp-fw-dtb: Authentication Finalize Done
[0000.860] I> oem authentication of cpubl-dtb header done
[0000.860] I> cpubl-dtb binary done read from storage
[0000.861] I> cpubl-dtb: Authentication init Done
[0000.863] I> parsing oem signed section of eks header done
[0000.863] I> eks binary init read from storage
[0000.864] I> cpubl-dtb: Authentication Finalize Done
[0000.865] I> oem authentication of eks header done
[0000.868] I> eks binary done read from storage
[0000.873] I> eks: Authentication init Done
[0000.877] I> eks: Authentication Finalize Done
[0000.881] I> EKB detected (length: 0x410) @ VA:0x52700400
��NOTICE:  BL31: v1.3(release):b5eeb33f7
NOTICE:  BL31: Built : 12:15:32, Jul 26 2021
ipc-unittest-main: 1519: Welcome to IPC unittest!!!
ipc-unittest-main: 1531: waiting forever
ipc-unittest-srv: 329: Init unittest services!!!
hwkey-agent: 41: hwkey-agent is running!!
hwkey-agent: 315: key_mgnt_processing .......
hwkey-agent: 223: Setting EKB key 0 to slot 14
hwkey-agent: 178: Init hweky-agent services!!
luks-srv: 40: luks-srv is running!!
luks-srv: 157: Init luks-srv IPC services!!
platform_bootstrap_epilog: trusty bootstrap complete
��

welcome to lk
calling constructors
initializing heap
creating bootstrap completion thread
top of bootstrap2()
initializing platform
bpmp: platform_init
tag is e73a758761f0c6d24a1e69a2ac6b5035
tag_show initialized
dt initialized
mail initialized
chipid initialized
fuse initialized
sku initialized
speedo initialized
ec_get_ec_list: found 45 ecs
ec initialized
ec_mrq initialized
vmon_populate_monitors: found 3 monitors
vmon initialized
adc initialized
fmon_populate_monitors: found 73 monitors
fmon initialized
fmon_mrq initialized
reset initialized
nvhs initialized
392 clocks registered
WARNING: pll_c4 has no dyn ramp
clk_mrq_init: mrq handler registered
clk initialized
nvlink initialized
io_dpd initialized
io_dpd initialized
thermal initialized
i2c5 controller initialized
initialized i2c mrq handling
i2c initialized
regulator initialized
avfs_clk_platform initialized
soctherm initialized
aotag initialized
powergate initialized
dvs initialized
pm initialized
pg_late initialized
strap initialized
tag initialized
emc initialized
clk_dt initialized
avfs_ccplex_platform initialized
tj_max: dt node not found
tj_init initialized
uphy_mrq_init: mrq handler registered
uphy_dt initialized
uphy initialized
safereg_init: period 80 ms
ec_late initialized
mrq initialized
��
  [0001.386] I> Welcome to Cboot
��fmon_post initialized
��[0001.386] I> Cboot Version: t194-cfa2bc91
[0001.386] I> CPU-BL Params @ 0xf2820000
[0001.387] I>  0) Base:0x00000000 Size:0x00000000
[0001.390] I>  1) Base:0xf1100000 Size:0x00100000
[0001.395] I>  2) Base:0xf2000000 Size:0x00200000
[0001.399] I>  3) Base:0xf1200000 Size:0x00200000
��clk_set_parent failed for clk i2c2, parent pll_aon (-22)
clk_set_parent failed for clk i2c8, parent pll_aon (-22)
clk_dt_late initialized
machine_check initialized
pm_post initialized
dbells initialized
avfs_clk_platform_post initialized
dmce initialized
cvc initialized
ccplex_avfs_hw_init: nafll_cluster0: not monitored
ccplex_avfs_hw_init: nafll_cluster1: not monitored
ccplex_avfs_hw_init: nafll_cluster2: not monitored
ccplex_avfs_hw_init: nafll_cluster3: not monitored
avfs_clk_mach_post initialized
regulator_post initialized
rm initialized
sc7_diag initialized
thermal_test initialized
serial_late initialized
clk_post initialized
clk_dt_post initialized
mc_reg initialized
pg_post initialized
dyn_modules initialized
sku_debugfs initialized
speedo_debugfs initialized
adc_debugfs initialized
clk_debugfs initialized
��[0001.404] I>  4) Base:0xf1000000 Size:0x00100000
[0001.483] I>  5) Base:0xf0f00000 Size:0x00100000
[0001.488] I>  6) Base:0xf3800000 Size:0x00400000
[0001.492] I>  7) Base:0xf1c00000 Size:0x00400000
[0001.496] I>  8) Base:0xf0e00000 Size:0x00100000
[0001.501] I>  9) Base:0xf0d00000 Size:0x00100000
[0001.505] I> 10) Base:0xf3000000 Size:0x00800000
[0001.510] I> 11) Base:0x40000000 Size:0x00040000
[0001.514] I> 12) Base:0xf0c00000 Size:0x00100000
[0001.519] I> 13) Base:0x40046000 Size:0x00002000
[0001.523] I> 14) Base:0x40048000 Size:0x00002000��emc_debugfs initialized
��
��dvs_debugfs initialized
��[0001.530] I> 15) Base:0xac000000 Size:0x00004000��fmon_debugfs initialized
vmon_debugfs initialized
pg_debugfs initialized
profile_fs initialized
debugfs_cons initialized
mail_fs initialized
profile initialized
cvc_debugfs initialized
dmce_debugfs initialized
ec_debugfs initialized
rm_debugfs initialized
soctherm_debug initialized
gr_reader initialized
mods initialized
dt_fs initialized
debugfs_mrq initialized
debug_mrq initialized
debug_safereg initialized
initializing target
calling apps_init()
starting app shell
entering main console loop
] ��
[0001.583] I> 16) Base:0x4004a000 Size:0x00002000
[0001.588] I> 17) Base:0xf0b00000 Size:0x00100000
[0001.592] I> 18) Base:0x4004c000 Size:0x00002000
[0001.597] I> 19) Base:0xf2200000 Size:0x00600000
[0001.601] I> 20) Base:0x4004e000 Size:0x00002000
[0001.606] I> 21) Base:0xf0ad0000 Size:0x0000c000
[0001.610] I> 22) Base:0x00000000 Size:0x00000000
[0001.615] I> 23) Base:0xf0ae0000 Size:0x00020000
[0001.619] I> 24) Base:0xf6000000 Size:0x02000000
[0001.623] I> 25) Base:0x40050000 Size:0x00002000
[0001.628] I> 26) Base:0x40040000 Size:0x00006000
[0001.632] I> 27) Base:0xf1800000 Size:0x00400000
[0001.637] I> 28) Base:0xf4c00000 Size:0x01400000
[0001.641] I> 29) Base:0xf1400000 Size:0x00400000
[0001.646] I> 30) Base:0x00000000 Size:0x00000000
[0001.650] I> 31) Base:0x00000000 Size:0x00000000
[0001.655] I> 32) Base:0xf8000000 Size:0x08000000
[0001.659] I> 33) Base:0x00000000 Size:0x00000000
[0001.664] I> 34) Base:0xf3c00000 Size:0x01000000
[0001.668] I> 35) Base:0xab000000 Size:0x01000000
[0001.673] I> 36) Base:0xa0000000 Size:0x0b000000
[0001.677] I> 37) Base:0xf2800000 Size:0x00800000
[0001.681] I> 38) Base:0x80000000 Size:0x20000000
[0001.686] I> 39) Base:0xb0000000 Size:0x08000000
[0001.690] I> 40) Base:0x00000000 Size:0x00000000
[0001.695] I> 41) Base:0x00000000 Size:0x00000000
[0001.699] I> 42) Base:0x00000000 Size:0x00000000
[0001.704] I> 43) Base:0x00000000 Size:0x00000000
[0001.708] I> 44) Base:0x00000000 Size:0x00000000
[0001.713] I> 45) Base:0x00000000 Size:0x00000000
[0001.717] GIC-SPI Target CPU: 0
[0001.720] Interrupts Init done
[0001.723] calling constructors
[0001.726] initializing heap
[0001.729] I> Heap: [0xa0699b80 ... 0xab000000]
[0001.733] initializing threads
[0001.736] initializing timers
[0001.739] creating bootstrap completion thread
[0001.743] top of bootstrap2()
[0001.746] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000
[0001.750] initializing platform
[0001.753] E> DEVICE_PROD: Invalid value data = 0, size = 0.
[0001.759] W> device prod register failed
[0001.762] I> Bl_dtb @0xaaf00000
[0001.769] W> "plugin-manager" doesn't exist, creating
[0001.770] W> "ids" doesn't exist, creating
[0001.775] W> "connection" doesn't exist, creating
[0001.779] W> "configs" doesn't exist, creating
[0001.790] E> failed to read label property for node 227172: 13
[0001.793] E> failed to read reg property for node 227260: 13
[0001.796] E> failed to read label property for node 227312: 13
[0001.802] E> failed to read label property for node 227380: 13
[0001.807] E> failed to read label property for node 227416: 13
[0001.813] E> failed to read label property for node 227452: 13
[0001.818] E> failed to read reg property for node 227520: 13
[0001.824] E> failed to read label property for node 227572: 13
[0001.830] I> Find /i2c@3160000's alias i2c0
[0001.832] I> Reading eeprom i2c=0 address=0x50
[0001.862] E> verify_cvm_eeprom_version: EEPROM incompatible version found
[0001.862] I> Eeprom read failed 0x35360018
[0001.863] I> Reading eeprom i2c=0 address=0x56
[0001.887] I> Device at /i2c@3160000:0x56
[0001.888] I> Find /i2c@3180000's alias i2c2
[0001.889] I> Reading eeprom i2c=2 address=0x54
[0001.890] E> I2C: slave not found in slaves.
[0001.891] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true.
[0001.892] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.892] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2.
[0001.901] E> eeprom: Failed to read I2C slave device
[0001.906] I> Eeprom read failed 0x3526070d
[0001.910] I> Reading eeprom i2c=2 address=0x57
[0001.914] E> I2C: slave not found in slaves.
[0001.918] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true.
[0001.926] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.932] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2.
[0001.941] E> eeprom: Failed to read I2C slave device
[0001.946] I> Eeprom read failed 0x3526070d
[0001.950] I> Reading eeprom i2c=2 address=0x52
[0001.954] E> I2C: slave not found in slaves.
[0001.958] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true.
[0001.966] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.972] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2.
[0001.981] E> eeprom: Failed to read I2C slave device
[0001.986] I> Eeprom read failed 0x3526070d
[0001.991] I> Find /i2c@c240000's alias i2c1
[0001.994] I> Reading eeprom i2c=1 address=0x52
[0002.001] E> I2C: Timeout while polling for bus clear. Last value 0x00000000.
[0002.005] E> I2C: Failed to clear bus for instance 1.
[0002.011] E> I2C: Failed to clear bus for instance 1.
[0002.015] E> I2C_DEV: Failed to initialize instance 1.
[0002.020] E> eeprom: Can't get handle to eeprom device @164
[0002.026] I> Eeprom read failed 0x3536002a
[0002.029] I> Reading eeprom i2c=1 address=0x50
[0002.036] E> I2C: Timeout while polling for bus clear. Last value 0x00000000.
[0002.041] E> I2C: Failed to clear bus for instance 1.
[0002.046] E> I2C: Failed to clear bus for instance 1.
[0002.051] E> I2C_DEV: Failed to initialize instance 1.
[0002.056] E> eeprom: Can't get handle to eeprom device @160
[0002.061] I> Eeprom read failed 0x3536002a
[0002.065] I> create_pm_ids: id: 2822-0000-700-L, len: 15
[0002.070] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93
[0002.081] I> Adding plugin-manager/ids/2822-0000-700=/i2c@3160000:module@0x56
[0002.089] W> "i2c@3160000" doesn't exist, creating
[0002.093] W> "module@0x56" doesn't exist, creating
[0002.099] W> "chip-id" doesn't exist, creating
[0002.102] I> Adding plugin-manager/chip-id/A02P
[0002.106] I> Plugin-manager override starting
[0002.111] I> node /plugin-manager/fragement-tegra-wdt-en matches
[0002.121] I> node /plugin-manager/fragement-soft-wdt matches
[0002.129] I> node /plugin-manager/fragment-pcie-c5-rp matches
[0002.133] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches
[0002.143] I> Disable plugin-manager status in FDT
[0002.144] I> Plugin-manager override finished successfully
[0002.144] I> gpio framework initialized
[0002.148] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver
[0002.155] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver
[0002.162] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46
[0002.169] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539
[0002.177] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539
[0002.184] W> tegrabl_tca9539_init: failed to fetch phandle from dt
[0002.190] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44
[0002.197] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539
[0002.205] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539
[0002.212] W> tegrabl_tca9539_init: failed to fetch phandle from dt
[0002.219] I> fixed regulator driver initialized
[0002.232] I> register 'maxim' power off handle
[0002.233] I> virtual i2c enabled
[0002.233] I> registered 'maxim,max20024' pmic
[0002.234] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver
[0002.240] I> Boot-device: eMMC
[0002.243] I> Boot_device: SDMMC_BOOT instance: 3
[0002.252] I> sdmmc-3 params source = boot args
[0002.252] I> create_pm_ids: id: 2822-0000-700-L, len: 15
[0002.257] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93
[0002.268] I> sdmmc bdev is already initialized
[0002.272] I> sdmmc-3 params source = boot args
[0002.303] I> Found 17 partitions in SDMMC_BOOT (instance 3)
[0002.316] I> Found 42 partitions in SDMMC_USER (instance 3)
[0002.327] I> enabling 'vdd-hdmi-5v0' regulator
[0002.333] I> regulator 'vdd-hdmi-5v0' already enabled
[0002.333] I> hdmi cable connected
[0002.336] W> set volts not configured for 'vdd-1v0'
[0002.338] W> set volts not configured for 'vdd-1v8-hs'
[0002.339] I> retrieved tmds range from prod_list_hdmi_soc
[0002.344] E> invalid display type
[0002.348] E> invalid display type
[0002.350] E> cannot find any other nvdisp nodes
[0002.365] I> edid read success
[0002.377] I> edid read success
[0002.378] I> width = 640, height = 480, frequency = 25174825
[0002.378] I> width = 640, height = 480, frequency = 25174825
[0002.379] I> width = 1920, height = 1080, frequency = 148500000
[0002.379] I> width = 1920, height = 1080, frequency = 148500000
[0002.379] I> width = 640, height = 480, frequency = 25174825
[0002.383] I> width = 720, height = 480, frequency = 26973026
[0002.389] I> width = 720, height = 480, frequency = 26973026
[0002.394] I> width = 720, height = 576, frequency = 26973026
[0002.400] I> width = 720, height = 576, frequency = 26973026
[0002.405] I> width = 1280, height = 720, frequency = 74175824
[0002.411] I> width = 1280, height = 720, frequency = 74175824
[0002.417] I> width = 1920, height = 1080, frequency = 148351648
[0002.422] I> width = 1920, height = 1080, frequency = 148351648
[0002.428] I> Best mode Width = 1920, Height = 1080, freq = 148351648
[0002.438] I> hdmi_enable, starting HDMI initialisation
[0002.443] I> hdmi_enable, HDMI initialisation complete
[0002.454] I> Load in CBoot Boot Options partition and parse it
[0002.461] E> Error -9 when finding node with path /boot-configuration
[0002.461] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file.
[0002.464] I> Using default boot order
[0002.467] I> boot-dev-order :-
[0002.470] I> 1.sd
[0002.472] I> 2.usb
[0002.474] I> 3.nvme
[0002.476] I> 4.emmc
[0002.477] I> 5.net
[0002.479] I> Hit any key to stop autoboot:     4       3       2       1
[0004.487] initializing target
[0004.487] calling apps_init()
[0004.488] starting app kernel_boot_app
[0004.507] I> found decompressor handler: lz4-legacy
[0004.508] I> decompressing BMP blob ...
[0004.520] I> Kernel type = Normal
[0004.520] I> ########## SD (0) boot ##########
[0004.520] I> No sdcard
[0004.521] I> -0 params source =
[0004.521] E> Blockdev open: exit error
[0004.521] E> SD boot failed, err: 724238353
[0004.521] I> ########## USB (0) boot ##########
[0004.527] W> No valid slot number is found in scratch register
[0004.527] W> Return default slot: _a
[0004.535] I> Validate XUSB-FW ...
[0004.535] I> T19x: Authenticate XUSB-FW (bin_type: 11), max size 0x28000
[0004.539] I> Encryption fuse is not ON
[0004.542] I> USB Firmware Version: 60.09 release
[0004.602] I> regulator of usb2-0 already enabled
[0004.610] I> regulator of usb2-1 already enabled
[0004.618] I> regulator of usb2-2 already enabled
[0004.629] I> enabling 'vdd-5v-sata' regulator
[0005.698] I> USB 2.0 port 2 new high-speed USB device detected
[0005.699] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0
[0005.800] I> Start to enumerate device
[0005.801] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0
[0005.806] I>
[0005.806] I> Enumerated USB Device 2109:2813
[0005.806] I>
[0005.808] I> Hub:
[0005.808] I>   Downstream ports        : 4
[0005.808] I>   Power switching         : Ganged
[0005.808] I>   Compound device         : No
[0005.809] I>   Over-current protection : Global
[0005.813] I>   Hub avg delay           : 4 ns
[0005.817] I> Enable hub ports
[0005.840] I> Device detected on port 2
[0005.843] I> Device detected on port 3
[0006.255] I> Device detected on port 4
[0006.861] I> Reset port 2
[0006.922] I> Port 2 device is low speed, skip enumeration
[0006.925] I> Reset port 3
[0006.988] I> Port 3 device is low speed, skip enumeration
[0006.995] I> Reset port 4
[0007.014] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0
[0007.115] I> Start to enumerate device
[0007.116] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4ad2000, cmd_ring.dma = 0xa4ad20c0
[0007.120] I> This device is non-MSD, skip enumeration
[0007.120] E> failed to start xhci controller
[0007.120] E> Error in init of XUSB host driver, err: 7979000d
[0007.121] W> Failed to initialize device 5-0
[0007.121] E> USB boot failed, err: 2037973005
[0007.125] I> ########## NVME (0) boot ##########
[0007.130] I> Initializing nvme device instance 0
[0007.134] I> Initializing nvme controller
[0007.138] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000
[0007.145] I> vpcie3v3-supply not found
[0007.148] I> vpcie12v-supply not found
[0007.152] W> Failed to get nvidia,plat-gpios
[0007.156] I> tegrabl_pcie_soc_preinit: (0):
[0007.160] I> Unpowergate
[0007.163] I> tegrabl_car_clk_disable(0) ...
[0007.166] I> tegrabl_car_rst_set(CORE, 0) ...
[0007.171] I> tegrabl_car_rst_set(APB, 0) ...
[0007.175] I> tegrabl_car_clk_enable(0) ...
[0007.179] I> tegrabl_car_rst_clear(APB, 0) ...
[0007.183] I> tegrabl_set_ctrl_state(0)
[0007.187] I> CLR PCIE_APB:6
[0007.189] I> tegrabl_pcie_soc_init: (0):
[0007.193] I> APPL initialization ...
[0007.196] I> poweron phys
[0007.199] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000
[0007.205] I> tegrabl_power_on_phy: power on phy @0x3e30000
[0007.211] I> tegrabl_power_on_phy: power on phy @0x3e40000
[0007.216] I> tegrabl_power_on_phy: power on phy @0x3e50000
[0007.221] I> tegrabl_power_on_phy: power on phy @0x3e60000
[0008.327] C> Failed to link up controller-0
[0008.327] W> Failed tegrabl_pcie_soc_init(), error=0x12
[0008.328] I> Failed to initialize SoC Host PCIe controller
[0008.328] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(0); error=0x12
[0008.329] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612
[0008.329] W> Failed to open NVME-0, err = 80800612
[0008.334] W> Failed to initialize device 10-0
[0008.338] E> NVME (0) boot failed, err: 0x80800612
[0008.342] I> ########## NVME (1) boot ##########
[0008.347] I> Initializing nvme device instance 1
[0008.351] I> Initializing nvme controller
[0008.355] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000
[0008.362] I> vpcie3v3-supply not found
[0008.365] I> vpcie12v-supply not found
[0008.369] W> Failed to get nvidia,plat-gpios
[0008.373] I> tegrabl_pcie_soc_preinit: (1):
[0008.377] I> Unpowergate
[0008.379] I> tegrabl_car_clk_disable(1) ...
[0008.383] I> tegrabl_car_rst_set(CORE, 1) ...
[0008.388] I> tegrabl_car_rst_set(APB, 1) ...
[0008.392] I> tegrabl_car_clk_enable(1) ...
[0008.396] I> tegrabl_car_rst_clear(APB, 1) ...
[0008.400] I> tegrabl_set_ctrl_state(1)
[0008.403] I> CLR PCIE_APB:6
[0008.406] I> tegrabl_pcie_soc_init: (1):
[0008.410] I> APPL initialization ...
[0008.413] I> poweron phys
[0008.416] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000
[0008.422] I> tegrabl_power_on_phy: power on phy @0x3e10000
[0008.529] I> PCIe controller-1 link is up
[0008.529] I> tegra_pcie_info[1].cfg0_base = 0x30000000
[0008.530] I> tegra_pcie_info[1].cfg1_base = 0x30020000
[0008.530] I> tegra_pcie_info[1].atu_dma_base = 0x30040000
[0008.530] I> tegra_pcie_bus[1].mem = 0x30200000
[0008.531] I> Scanning busnr: 0 devfn: 0
[0008.531] I> PCIe IDs: 0x1ad210de
[0008.534] I> PCIe RID_CC: 0x60400a1
[0008.537] I> Scanning busnr: 1 devfn: 0
[0008.541] I> PCIe IDs: 0x91711b4b
[0008.544] I> PCIe RID_CC: 0x1060113
[0008.548] I> PCI Config: I/O=0x30100000, Memory=0x30200000
[0008.553] I> IO bar_num=0 bar=0x30100000
[0008.557] I> IO bar_num=1 bar=0x30100008
[0008.560] I> IO bar_num=2 bar=0x30100010
[0008.564] I> IO bar_num=3 bar=0x30100018
[0008.568] I> IO bar_num=4 bar=0x30100020
[0008.572] I> MEM bar_num=5 bar=0x30200000
[0008.576] I> Number of PCIe devices detected: 2
[0008.580] E> tegrabl_nvme_init: Failed tegrabl_pcie_get_dev(1); error=0x0
[0008.587] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612
[0008.593] W> Failed to open NVME-1, err = 80800612
[0008.598] W> Failed to initialize device 10-1
[0008.602] E> NVME (1) boot failed, err: 0x80800612
[0008.606] I> ########## NVME (2) boot ##########
[0008.611] I> Initializing nvme device instance 2
[0008.615] I> Initializing nvme controller
[0008.620] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000
[0008.626] I> vpcie3v3-supply not found
[0008.629] I> vpcie12v-supply not found
[0008.633] W> Failed to get nvidia,plat-gpios
[0008.637] I> tegrabl_pcie_soc_preinit: (2):
[0008.641] I> Unpowergate
[0008.643] I> tegrabl_car_clk_disable(2) ...
[0008.647] I> tegrabl_car_rst_set(CORE, 2) ...
[0008.652] I> tegrabl_car_rst_set(APB, 2) ...
[0008.656] I> tegrabl_car_clk_enable(2) ...
[0008.660] I> tegrabl_car_rst_clear(APB, 2) ...
[0008.664] I> tegrabl_set_ctrl_state(2)
[0008.668] I> CLR PCIE_APB:6
[0008.670] I> tegrabl_pcie_soc_init: (2):
[0008.674] I> APPL initialization ...
[0008.677] I> poweron phys
[0008.680] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000
[0008.686] I> tegrabl_power_on_phy: controller 2 not available
[0008.692] E> Failed to power on phy on controller-2
[0008.697] W> Failed tegrabl_pcie_soc_init(), error=0x1
[0008.701] I> Failed to initialize SoC Host PCIe controller
[0008.707] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(2); error=0x1
[0008.713] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601
[0008.720] W> Failed to open NVME-2, err = 80800601
[0008.724] W> Failed to initialize device 10-2
[0008.728] E> NVME (2) boot failed, err: 0x80800601
[0008.733] I> ########## NVME (3) boot ##########
[0008.738] I> Initializing nvme device instance 3
[0008.742] I> Initializing nvme controller
[0008.746] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000
[0008.752] I> vpcie3v3-supply not found
[0008.756] I> vpcie12v-supply not found
[0008.759] W> Failed to get nvidia,plat-gpios
[0008.764] I> tegrabl_pcie_soc_preinit: (3):
[0008.768] I> Unpowergate
[0008.770] I> tegrabl_car_clk_disable(3) ...
[0008.774] I> tegrabl_car_rst_set(CORE, 3) ...
[0008.778] I> tegrabl_car_rst_set(APB, 3) ...
[0008.782] I> tegrabl_car_clk_enable(3) ...
[0008.786] I> tegrabl_car_rst_clear(APB, 3) ...
[0008.791] I> tegrabl_set_ctrl_state(3)
[0008.794] I> CLR PCIE_APB:6
[0008.797] I> tegrabl_pcie_soc_init: (3):
[0008.800] I> APPL initialization ...
[0008.804] I> poweron phys
[0008.807] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000
[0008.813] I> tegrabl_power_on_phy: power on phy @0x3e80000
[0009.918] C> Failed to link up controller-3
[0009.919] W> Failed tegrabl_pcie_soc_init(), error=0x12
[0009.919] I> Failed to initialize SoC Host PCIe controller
[0009.920] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(3); error=0x12
[0009.920] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612
[0009.921] W> Failed to open NVME-3, err = 80800612
[0009.925] W> Failed to initialize device 10-3
[0009.929] E> NVME (3) boot failed, err: 0x80800612
[0009.934] I> ########## NVME (4) boot ##########
[0009.938] I> Initializing nvme device instance 4
[0009.943] I> Initializing nvme controller
[0009.947] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000
[0009.953] I> vpcie3v3-supply not found
[0009.957] I> vpcie12v-supply not found
[0009.960] W> Failed to get nvidia,plat-gpios
[0009.964] I> tegrabl_pcie_soc_preinit: (4):
[0009.968] I> Unpowergate
[0009.971] I> tegrabl_car_clk_disable(4) ...
[0009.975] I> tegrabl_car_rst_set(CORE, 4) ...
[0009.979] I> tegrabl_car_rst_set(APB, 4) ...
[0009.983] I> tegrabl_car_clk_enable(4) ...
[0009.987] I> tegrabl_car_rst_clear(APB, 4) ...
[0009.991] I> tegrabl_set_ctrl_state(4)
[0009.995] I> CLR PCIE_APB:6
[0009.998] I> tegrabl_pcie_soc_init: (4):
[0010.001] I> APPL initialization ...
[0010.005] I> poweron phys
[0010.008] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000
[0010.014] I> tegrabl_power_on_phy: controller 4 not available
[0010.019] E> Failed to power on phy on controller-4
[0010.024] W> Failed tegrabl_pcie_soc_init(), error=0x1
[0010.029] I> Failed to initialize SoC Host PCIe controller
[0010.034] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(4); error=0x1
[0010.041] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601
[0010.047] W> Failed to open NVME-4, err = 80800601
[0010.052] W> Failed to initialize device 10-4
[0010.056] E> NVME (4) boot failed, err: 0x80800601
[0010.061] I> ########## NVME (5) boot ##########
[0010.065] I> Initializing nvme device instance 5
[0010.070] I> Initializing nvme controller
[0010.074] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000
[0010.080] I> i=0, reg_phandle=0x1b
[0010.086] I> reg_voltage=3300000
[0010.086] I> tegrabl_pcie_enable_regulators: regulator_set_voltage(0x1b, 3300000)
[0010.099] I> enabling 'vdd-3v3-pcie' regulator
[0010.099] I> i=1, reg_phandle=0x1c
[0010.103] I> reg_voltage=1200000
[0010.104] I> tegrabl_pcie_enable_regulators: regulator_set_voltage(0x1c, 1200000)
[0010.116] I> enabling 'vdd-12v-pcie' regulator
[0010.117] I> tegrabl_pcie_soc_preinit: (5):
[0010.120] I> Unpowergate
[0010.122] I> tegrabl_car_clk_disable(5) ...
[0010.126] I> tegrabl_car_rst_set(CORE, 5) ...
[0010.130] I> tegrabl_car_rst_set(APB, 5) ...
[0010.134] I> tegrabl_car_clk_enable(5) ...
[0010.138] I> tegrabl_car_rst_clear(APB, 5) ...
[0010.143] I> tegrabl_set_ctrl_state(5)
[0010.146] I> CLR PCIE_APB:6
[0010.149] I> tegrabl_pcie_soc_init: (5):
[0010.153] I> APPL initialization ...
[0010.156] I> poweron phys
[0010.159] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000
[0010.165] I> tegrabl_power_on_phy: power on phy @0x3eb0000
[0010.170] I> tegrabl_power_on_phy: power on phy @0x3ec0000
[0010.176] I> tegrabl_power_on_phy: power on phy @0x3ed0000
[0010.181] I> tegrabl_power_on_phy: power on phy @0x3ee0000
[0010.186] I> tegrabl_power_on_phy: power on phy @0x3ef0000
[0010.192] I> tegrabl_power_on_phy: power on phy @0x3f00000
[0010.197] I> tegrabl_power_on_phy: power on phy @0x3f10000
[0010.202] I> tegrabl_power_on_phy: power on phy @0x3f20000
[0011.308] C> Failed to link up controller-5
[0011.308] W> Failed tegrabl_pcie_soc_init(), error=0x12
[0011.309] I> Failed to initialize SoC Host PCIe controller
[0011.309] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(5); error=0x12
[0011.310] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612
[0011.310] W> Failed to open NVME-5, err = 80800612
[0011.315] W> Failed to initialize device 10-5
[0011.319] E> NVME (5) boot failed, err: 0x80800612
[0011.323] I> ########## Fixed storage boot ##########
[0011.328] I> Loading kernel-bootctrl from partition
[0011.333] I> Loading partition kernel-bootctrl at 0xa4b60000 from device(0x1)
[0011.346] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid
[0011.347] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data
[0011.360] I> Already published: 00010003
[0011.361] I> Look for boot partition
[0011.361] I> Fallback: assuming 0th partition is boot partition
[0011.367] I> Detect filesystem
[0011.394] I> Loading extlinux.conf ...
[0011.394] I> Loading extlinux.conf binary from rootfs ...
[0011.395] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf
[0011.438] I> Loading extlinux.conf sig file from rootfs ...
[0011.438] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf.sig
[0011.463] I> Validate extlinux.conf ...
[0011.463] I> T19x: Authenticate extlinux.conf (bin_type: 54), max size 0x2000
[0011.464] I> Encryption fuse is not ON
[0011.464] I> L4T boot options
[0011.464] I> [1]: "primary kernel"
[0011.464] I> Enter choice:
[0014.466] I> Continuing with default option: 1
[0014.466] I> Loading kernel ...
[0014.466] I> Loading kernel binary from rootfs ...
[0014.467] I> rootfs path: /sdmmc_user/boot/Image
[0014.688] I> Loading kernel sig file from rootfs ...
[0014.688] I> rootfs path: /sdmmc_user/boot/Image.sig
[0014.707] I> overload load_size to 34484232 (from 34484240)
[0014.707] I> Validate kernel ...
[0014.707] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000
[0015.022] I> Encryption fuse is not ON
[0015.053] I> Loading kernel-dtb ...
[0015.054] I> No kernel-dtb binary path
[0015.054] I> Continue to load from partition ...
[0015.054] W> No valid slot number is found in scratch register
[0015.055] W> Return default slot: _a
[0015.055] I> A/B: bin_type (38) slot 0
[0015.055] I> Loading kernel-dtb from partition
[0015.057] I> Loading partition kernel-dtb at 0x91000000 from device(0x1)
[0015.072] I> Validate kernel-dtb ...
[0015.072] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000
[0015.076] I> Encryption fuse is not ON
[0015.078] I> Loading ramdisk from rootfs ...
[0015.081] I> Loading ramdisk binary from rootfs ...
[0015.086] I> rootfs path: /sdmmc_user/boot/initrd
[0015.148] I> Loading ramdisk sig file from rootfs ...
[0015.149] I> rootfs path: /sdmmc_user/boot/initrd.sig
[0015.167] I> overload load_size to 7238344 (from 7238352)
[0015.168] I> Validate ramdisk ...
[0015.168] I> T19x: Authenticate ramdisk (bin_type: 54), max size 0x4000000
[0015.234] I> Encryption fuse is not ON
[0015.248] I> Kernel hdr @0xa4b60000
[0015.248] I> Kernel dtb @0x90000000
[0015.248] I> decompressor handler not found
[0015.249] I> Copying kernel image (34484232 bytes) from 0xa4b60000 to 0x80080000 ... [0015.259] I> Done
[0015.260] I> Updated bpmp info to DTB
[0015.262] I> Ramdisk: Base: 0x92000000; Size: 0x6e72c8
[0015.262] I> Updated initrd info to DTB
[0015.262] W> WARN: Fail to override "console=none" in commandline
[0015.263] I> Active rootfs suffix:
[0015.264] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params
[0015.271] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params
[0015.279] W> No valid slot number is found in scratch register
[0015.284] W> Return default slot: _a
[0015.288] I> Active slot suffix:
[0015.291] I> add_boot_slot_suffix: slot_suffix =
[0015.296] I> Linux Cmdline: console=ttyTCU0,115200 video=tegrafb earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= tegra_fbmem=0x800000@0xa06aa000 lut_mem=0x2008@0xa06a5000 usbcore.old_
[0015.325] I> Updated bootarg info to DTB
[0015.329] E> Error 892665857: Failed to get CVM EEPROM contents
[0015.335] E> Booting w/o MAC ddresses for WIFI, Bluetooth & Ethernet
[0015.341] E> Failed to get WIFI MAC address
[0015.345] E> Error 892665857: Failed to get CVM EEPROM contents
[0015.351] E> Booting w/o MAC ddresses for WIFI, Bluetooth & Ethernet
[0015.357] E> Failed to get Bluetooth MAC address
[0015.361] E> Error 892665857: Failed to get CVM EEPROM contents
[0015.367] E> Booting w/o MAC ddresses for WIFI, Bluetooth & Ethernet
[0015.373] E> Failed to get Ethernet MAC address
[0015.378] W> "plugin-manager" doesn't exist, creating
[0015.383] W> "chip-id" doesn't exist, creating
[0015.387] I> Adding /chosen/plugin-manager/chip-id
[0015.392] W> "configs" doesn't exist, creating
[0015.396] I> Adding /chosen/plugin-manager/configs
[0015.400] W> "ids" doesn't exist, creating
[0015.404] I> Adding /chosen/plugin-manager/ids
[0015.409] W> "odm-data" doesn't exist, creating
[0015.413] I> Adding /chosen/plugin-manager/odm-data
[0015.421] W> "memory" doesn't exist, creating
[0015.422] I> [0] START: 0x80000000, END: 0xac000000
[0015.427] I> [1] START: 0xac004000, END: 0xf0ad0000
[0015.431] I> [2] START: 0xf0adc000, END: 0xf0ae0000
[0015.436] I> dram_block larger than 80000000
[0015.440] I> [3] START: 0x100000000, END: 0x880000000
[0015.445] I> added [base:0x80000000, size:0x2c000000] to /memory
[0015.451] I> added [base:0xac200000, size:0x44800000] to /memory
[0015.457] I> added [base:0x100000000, size:0x780000000] to /memory
[0015.464] I> Updated memory info to DTB
[0015.467] E> add_disp_param: failed to get display params for du=1
[0015.473] W> "reset" doesn't exist, creating
[0015.477] I> Adding ecid(00000001647e25c80000000010ff8200) to DT
[0015.483] I> NVG: Logical CPU: 0; MPIDR: 0x80000000
[0015.487] I> NVG: Logical CPU: 1; MPIDR: 0x80000001
[0015.492] I> NVG: Logical CPU: 2; MPIDR: 0x80000100
[0015.497] I> NVG: Logical CPU: 3; MPIDR: 0x80000101
[0015.501] I> NVG: Logical CPU: 4; MPIDR: 0x80000200
[0015.506] I> NVG: Logical CPU: 5; MPIDR: 0x80000201
[0015.511] I> NVG: Logical CPU: 6; MPIDR: 0x80000300
[0015.516] I> NVG: Logical CPU: 7; MPIDR: 0x80000301
[0015.522] W> "misc-data" doesn't exist, creating
[0015.525] I> Boot-device: eMMC
[0015.528] I> Add boot-sdmmc to plugin-manager/misc-data
[0015.533] I> Add storage-sdmmc to plugin-manager/misc-data
[0015.538] W> Unknown storage device
[0015.542] E> Error 892665857: Failed to read CVM EEPROM
[0015.546] E> Failed to get serial number
[0015.550] I> Plugin-manager override starting
[0015.555] I> node /plugin-manager/fragement-tegra-wdt-en matches
[0015.562] I> node /plugin-manager/fragement-soft-wdt matches
[0015.570] I> node /plugin-manager/fragment-pcie-c5-rp matches
[0015.574] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches
[0015.587] I> Disable plugin-manager status in FDT
[0015.587] I> Plugin-manager override finished successfully
[0015.588] I> tegrabl_load_kernel_and_dtb: Done
[0015.610] I> Kernel EP: 0x80080000, DTB: 0x90000000
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.253-tegra (buildbrain@mobile-u64-5497-d3000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) )1
[    0.000000] Boot CPU: AArch64 Processor [4e0f0040]
[    0.000000] OF: fdt:memory scan node memory, reg size 48,
[    0.000000] OF: fdt: - 80000000 ,  2c000000
[    0.000000] OF: fdt: - ac200000 ,  44800000
[    0.000000] OF: fdt: - 100000000 ,  780000000
[    0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '')
[    0.000000] bootconsole [tegra_comb_uart0] enabled
[    0.000000] Found tegra_fbmem: 00800000@a06aa000
[    0.000000] Found lut_mem: 00002008@a06a5000
[    1.726423] eqos_get_mac_address_dtb: bad mac address at /chosen/nvidia,ether-mac: null.
[    1.726607] eqos 2490000.ether_qos (unnamed net_device) (uninitialized): ether-mac read from DT failed -99
��WARNING: pll_d3 has no dyn ramp
��[   11.870946] tegra-i2c c240000.i2c: pio timed out addr: 0x8 tlen:28 rlen:24
[   11.871179] tegra-i2c c240000.i2c: --- register dump for debugging ----
[   11.871363] tegra-i2c c240000.i2c: I2C_CNFG - 0x22c00
[   11.871504] tegra-i2c c240000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001
[   11.871709] tegra-i2c c240000.i2c: I2C_FIFO_CONTROL - 0x0
[   11.871856] tegra-i2c c240000.i2c: I2C_FIFO_STATUS - 0x800080
[   11.872054] tegra-i2c c240000.i2c: I2C_MST_FIFO_CONTROL - 0x70000
[   11.872220] tegra-i2c c240000.i2c: I2C_MST_FIFO_STATUS - 0x7c0000
[   11.872383] tegra-i2c c240000.i2c: I2C_MST_PACKET_TRANSFER_CNT - 0x0
[   11.872578] tegra-i2c c240000.i2c: I2C_INT_MASK - 0x7d
[   11.872721] tegra-i2c c240000.i2c: I2C_INT_STATUS - 0x2
[   11.872869] tegra-i2c c240000.i2c: i2c transfer timed out addr: 0x8
[   11.873103] ucsi_ccg 1-0008: read version failed
[   11.873232] ucsi_ccg 1-0008: get_fw_info fail,, err=-110
[   22.110960] tegra-i2c c240000.i2c: pio timed out addr: 0x40 tlen:16 rlen:0
[   22.111152] tegra-i2c c240000.i2c: --- register dump for debugging ----
[   22.111297] tegra-i2c c240000.i2c: I2C_CNFG - 0x22c00
[   22.111425] tegra-i2c c240000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001
[   22.111589] tegra-i2c c240000.i2c: I2C_FIFO_CONTROL - 0x0
[   22.111711] tegra-i2c c240000.i2c: I2C_FIFO_STATUS - 0x800080
[   22.111836] tegra-i2c c240000.i2c: I2C_MST_FIFO_CONTROL - 0x70000
[   22.111984] tegra-i2c c240000.i2c: I2C_MST_FIFO_STATUS - 0x7f0000
[   22.112115] tegra-i2c c240000.i2c: I2C_MST_PACKET_TRANSFER_CNT - 0x0
[   22.112253] tegra-i2c c240000.i2c: I2C_INT_MASK - 0x7c
[   22.112382] tegra-i2c c240000.i2c: I2C_INT_STATUS - 0x2
[   22.112499] tegra-i2c c240000.i2c: i2c transfer timed out addr: 0x40
[   22.112672] ina3221x 1-0040: ina3221 reset failure status: 0xffffff92
[   32.350973] tegra-i2c c240000.i2c: pio timed out addr: 0x41 tlen:16 rlen:0
[   32.351164] tegra-i2c c240000.i2c: --- register dump for debugging ----
[   32.351308] tegra-i2c c240000.i2c: I2C_CNFG - 0x22c00
[   32.351427] tegra-i2c c240000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001
[   32.351584] tegra-i2c c240000.i2c: I2C_FIFO_CONTROL - 0x0
[   32.351702] tegra-i2c c240000.i2c: I2C_FIFO_STATUS - 0x800080
[   32.351824] tegra-i2c c240000.i2c: I2C_MST_FIFO_CONTROL - 0x70000
[   32.351969] tegra-i2c c240000.i2c: I2C_MST_FIFO_STATUS - 0x7f0000
[   32.352101] tegra-i2c c240000.i2c: I2C_MST_PACKET_TRANSFER_CNT - 0x0
[   32.352237] tegra-i2c c240000.i2c: I2C_INT_MASK - 0x7c
[   32.352363] tegra-i2c c240000.i2c: I2C_INT_STATUS - 0x2
[   32.352483] tegra-i2c c240000.i2c: i2c transfer timed out addr: 0x41
[   32.352652] ina3221x 1-0041: ina3221 reset failure status: 0xffffff92
[   36.794338] cgroup: cgroup2: unknown option "nsdelegate"
[   37.906271] Could not get extcon-dev /xhci@3610000:id(0)
[   37.910047] Could not get extcon-dev /xudc@3550000:vbus(0)
[   37.910770] Could not get extcon-dev /host1x/nvdisplay@15210000:typec0(0)
[   37.911242] Could not get extcon-dev /host1x/nvdisplay@15220000:typec1(1)
[   37.927663] Could not get extcon-dev /xhci@3610000:id(0)
[   37.931543] Could not get extcon-dev /xudc@3550000:vbus(0)
[   37.932481] Could not get extcon-dev /host1x/nvdisplay@15210000:typec0(0)
[   37.932922] Could not get extcon-dev /host1x/nvdisplay@15220000:typec1(1)
[   37.937834] Could not get extcon-dev /xhci@3610000:id(0)
[   38.077783] random: crng init done
[   38.077913] random: 7 urandom warning(s) missed due to ratelimiting
[  103.022688] Please complete system configuration setup on desktop to proceed...