Advertisement
Guest User

Untitled

a guest
Feb 2nd, 2022
101
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
  1. U-Boot TPL 2021.04-11559-gcdc9267734 (Jan 31 2022 - 10:52:59)
  2. Channel 0: LPDDR4, 50MHz
  3. BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
  4. Channel 1: LPDDR4, 50MHz
  5. BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
  6. 256B stride
  7. lpddr4_set_rate: change freq to 400000000 mhz 0, 1
  8. lpddr4_set_rate: change freq to 800000000 mhz 1, 0
  9. Trying to boot from BOOTROM
  10. Returning to boot ROM...
  11.  
  12. U-Boot SPL 2021.04-11559-gcdc9267734 (Jan 31 2022 - 10:52:59 +0000)
  13. Trying to boot from SPI
  14. NOTICE: BL31: v2.5(release):v2.5
  15. NOTICE: BL31: Built : 10:51:26, Jan 31 2022
  16.  
  17.  
  18. U-Boot 2021.04-11559-gcdc9267734 (Jan 31 2022 - 10:52:59 +0000)
  19.  
  20. SoC: Rockchip rk3399
  21. Reset cause: POR
  22. Model: Pine64 RockPro64 v2.1
  23. DRAM: 3.9 GiB
  24. PMIC: RK808
  25. MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
  26. Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
  27. *** Warning - bad CRC, using default environment
  28.  
  29. In: serial
  30. Out: serial
  31. Err: serial
  32. Model: Pine64 RockPro64 v2.1
  33. Net: eth0: ethernet@fe300000
  34. starting USB...
  35. Bus usb@fe380000: USB EHCI 1.00
  36. Bus usb@fe3a0000: USB OHCI 1.0
  37. Bus usb@fe3c0000: USB EHCI 1.00
  38. Bus usb@fe3e0000: USB OHCI 1.0
  39. Bus dwc3: usb maximum-speed not found
  40. Register 2000140 NbrPorts 2
  41. Starting the controller
  42. USB XHCI 1.10
  43. scanning bus usb@fe380000 for devices... 1 USB Device(s) found
  44. scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
  45. scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
  46. scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found
  47. scanning bus dwc3 for devices... 1 USB Device(s) found
  48. scanning usb for storage devices... 0 Storage Device(s) found
  49. Hit any key to stop autoboot: 0
  50. Card did not respond to voltage select! : -110
  51. Card did not respond to voltage select! : -110
  52. rockchip_pcie pcie@f8000000: PCIe link training gen1 timeout!
  53.  
  54. Device 0: unknown device
  55. rockchip_pcie pcie@f8000000: failed to find ep-gpios property
  56. scanning bus for devices...
  57.  
  58. Device 0: unknown device
  59.  
  60. Device 0: unknown device
  61. rockchip_pcie pcie@f8000000: failed to find ep-gpios property
  62. Speed: 1000, full duplex
  63. BOOTP broadcast 1
  64. DHCP client bound to address 192.168.0.156 (107 ms)
  65. *** ERROR: `serverip' not set
  66. Cannot autoload with TFTPGET
  67. missing environment variable: pxeuuid
  68. missing environment variable: bootfile
  69. Retrieving file: pxelinux.cfg/01-e6-41-ab-b7-a6-86
  70. Speed: 1000, full duplex
  71. *** ERROR: `serverip' not set
  72. missing environment variable: bootfile
  73. Retrieving file: pxelinux.cfg/C0A8009C
  74. Speed: 1000, full duplex
  75. *** ERROR: `serverip' not set
  76. missing environment variable: bootfile
  77. Retrieving file: pxelinux.cfg/C0A8009
  78. Speed: 1000, full duplex
  79. *** ERROR: `serverip' not set
  80. missing environment variable: bootfile
  81. Retrieving file: pxelinux.cfg/C0A800
  82. Speed: 1000, full duplex
  83. *** ERROR: `serverip' not set
  84. missing environment variable: bootfile
  85. Retrieving file: pxelinux.cfg/C0A80
  86. Speed: 1000, full duplex
  87. *** ERROR: `serverip' not set
  88. missing environment variable: bootfile
  89. Retrieving file: pxelinux.cfg/C0A8
  90. Speed: 1000, full duplex
  91. *** ERROR: `serverip' not set
  92. missing environment variable: bootfile
  93. Retrieving file: pxelinux.cfg/C0A
  94. Speed: 1000, full duplex
  95. *** ERROR: `serverip' not set
  96. missing environment variable: bootfile
  97. Retrieving file: pxelinux.cfg/C0
  98. Speed: 1000, full duplex
  99. *** ERROR: `serverip' not set
  100. missing environment variable: bootfile
  101. Retrieving file: pxelinux.cfg/C
  102. Speed: 1000, full duplex
  103. *** ERROR: `serverip' not set
  104. missing environment variable: bootfile
  105. Retrieving file: pxelinux.cfg/default-arm-rk3399-rockpro64_rk3399
  106. Speed: 1000, full duplex
  107. *** ERROR: `serverip' not set
  108. missing environment variable: bootfile
  109. Retrieving file: pxelinux.cfg/default-arm-rk3399
  110. Speed: 1000, full duplex
  111. *** ERROR: `serverip' not set
  112. missing environment variable: bootfile
  113. Retrieving file: pxelinux.cfg/default-arm
  114. Speed: 1000, full duplex
  115. *** ERROR: `serverip' not set
  116. missing environment variable: bootfile
  117. Retrieving file: pxelinux.cfg/default
  118. Speed: 1000, full duplex
  119. *** ERROR: `serverip' not set
  120. Config file not found
  121. rockchip_pcie pcie@f8000000: failed to find ep-gpios property
  122. Speed: 1000, full duplex
  123. BOOTP broadcast 1
  124. DHCP client bound to address 192.168.0.156 (105 ms)
  125. *** ERROR: `serverip' not set
  126. Cannot autoload with TFTPGET
  127. Speed: 1000, full duplex
  128. BOOTP broadcast 1
  129. DHCP client bound to address 192.168.0.156 (4 ms)
  130. *** Warning: no boot file name; using 'C0A8009C.img'
  131. Using ethernet@fe300000 device
  132. TFTP from server 192.168.0.178; our IP address is 192.168.0.156
  133. Filename 'C0A8009C.img'.
  134. Load address: 0x2080000
  135. Loading: *
  136. TFTP error: 'file /srv/tftp/C0A8009C.img not found' (1)
  137. Not retrying...
  138. SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
  139. dhcp - boot image via network using DHCP/TFTP protocol
  140.  
  141. Usage:
  142. dhcp [loadAddress] [[hostIPaddr:]bootfilename]
  143. ## Executing script at 00500000
  144. Wrong image format for "source" command
  145. SCRIPT FAILED: continuing...
  146. => pxe get
  147. missing environment variable: pxeuuid
  148. missing environment variable: bootfile
  149. Retrieving file: pxelinux.cfg/01-e6-41-ab-b7-a6-86
  150. Speed: 1000, full duplex
  151. Using ethernet@fe300000 device
  152. TFTP from server 192.168.0.178; our IP address is 192.168.0.156
  153. Filename 'pxelinux.cfg/01-e6-41-ab-b7-a6-86'.
  154. Load address: 0x600000
  155. Loading: #
  156. 149.4 KiB/s
  157. done
  158. Bytes transferred = 307 (133 hex)
  159. Config file found
  160. => pxe boot
  161. 1: rockpro64
  162. missing environment variable: bootfile
  163. Retrieving file: /combined.img.gz
  164. Speed: 1000, full duplex
  165. Using ethernet@fe300000 device
  166. TFTP from server 192.168.0.178; our IP address is 192.168.0.156
  167. Filename '/combined.img.gz'.
  168. Load address: 0x6000000
  169. Loading: #################################################################
  170. #################################################################
  171. #################################################################
  172. #################################################################
  173. #################################################################
  174. #################################################################
  175. #################################################################
  176. #################################################################
  177. #################################################################
  178. #################################################################
  179. #################################################################
  180. #################################################################
  181. #################################################################
  182. #################################################################
  183. #################################################################
  184. #################################################################
  185. ##########
  186. 2.8 MiB/s
  187. done
  188. Bytes transferred = 15404345 (eb0d39 hex)
  189. missing environment variable: bootfile
  190. Retrieving file: /ltsp/rockpro64/vmlinuz
  191. Speed: 1000, full duplex
  192. Using ethernet@fe300000 device
  193. TFTP from server 192.168.0.178; our IP address is 192.168.0.156
  194. Filename '/ltsp/rockpro64/vmlinuz'.
  195. Load address: 0x2080000
  196. Loading: #################################################################
  197. #################################################################
  198. #################################################################
  199. #################################################################
  200. #################################################################
  201. #################################################################
  202. #################################################################
  203. #################################################################
  204. #################################################################
  205. #################################################################
  206. #################################################################
  207. #################################################################
  208. #################################################################
  209. #################################################################
  210. #################################################################
  211. #################################################################
  212. #################################################################
  213. #################################################################
  214. #################################################################
  215. #################################################################
  216. #################################################################
  217. #################################################################
  218. #################################################################
  219. #################################################################
  220. #################################################################
  221. #################################################################
  222. #################################################################
  223. #################################################################
  224. #################################################################
  225. ##############################################################
  226. 3.6 MiB/s
  227. done
  228. Bytes transferred = 28580352 (1b41a00 hex)
  229. append: root=/dev/nfs nfsroot=192.168.0.178:/srv/ltsp ltsp.image=images/rockpro64.img loop.max_part=9
  230. missing environment variable: bootfile
  231. Retrieving file: /dtb/rockchip/rk3399-rockpro64.dtb
  232. Speed: 1000, full duplex
  233. Using ethernet@fe300000 device
  234. TFTP from server 192.168.0.178; our IP address is 192.168.0.156
  235. Filename '/dtb/rockchip/rk3399-rockpro64.dtb'.
  236. Load address: 0x1f00000
  237. Loading: ######
  238. 3.1 MiB/s
  239. done
  240. Bytes transferred = 78767 (133af hex)
  241. Moving Image from 0x2080000 to 0x2200000, end=3de0000
  242. ## Flattened Device Tree blob at 01f00000
  243. Booting using the fdt blob at 0x1f00000
  244. Loading Ramdisk to f1054000, end f1f04d39 ... OK
  245. Loading Device Tree to 00000000f103d000, end 00000000f10533ae ... OK
  246.  
  247. Starting kernel ...
  248.  
  249. [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
  250. [ 0.000000] Linux version 5.10.63-rockchip64 (root@runner4) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #21.08.2 SMP PREEMPT Wed Sep 8 10:57:23 UTC 2021
  251. [ 0.000000] Machine model: Pine64 RockPro64 v2.1
  252. [ 0.000000] efi: UEFI not found.
  253. [ 0.000000] NUMA: No NUMA configuration found
  254. [ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
  255. [ 0.000000] NUMA: NODE_DATA [mem 0xf77dd100-0xf77defff]
  256. [ 0.000000] Zone ranges:
  257. [ 0.000000] DMA [mem 0x0000000000200000-0x00000000f7ffffff]
  258. [ 0.000000] DMA32 empty
  259. [ 0.000000] Normal empty
  260. [ 0.000000] Movable zone start for each node
  261. [ 0.000000] Early memory node ranges
  262. [ 0.000000] node 0: [mem 0x0000000000200000-0x00000000f7ffffff]
  263. [ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
  264. [ 0.000000] cma: Reserved 128 MiB at 0x00000000e9000000
  265. [ 0.000000] psci: probing for conduit method from DT.
  266. [ 0.000000] psci: PSCIv1.1 detected in firmware.
  267. [ 0.000000] psci: Using standard PSCI v0.2 function IDs
  268. [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
  269. [ 0.000000] psci: SMC Calling Convention v1.2
  270. [ 0.000000] percpu: Embedded 33 pages/cpu s94232 r8192 d32744 u135168
  271. [ 0.000000] Detected VIPT I-cache on CPU0
  272. [ 0.000000] CPU features: detected: ARM erratum 845719
  273. [ 0.000000] CPU features: detected: GIC system register CPU interface
  274. [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 999432
  275. [ 0.000000] Policy zone: DMA
  276. [ 0.000000] Kernel command line: root=/dev/nfs nfsroot=192.168.0.178:/srv/ltsp ltsp.image=images/rockpro64.img loop.max_part=9
  277. [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
  278. [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
  279. [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
  280. [ 0.000000] Memory: 3805624K/4061184K available (14848K kernel code, 2630K rwdata, 5976K rodata, 4352K init, 578K bss, 124488K reserved, 131072K cma-reserved)
  281. [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
  282. [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
  283. [ 0.000000] rcu: RCU event tracing is enabled.
  284. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
  285. [ 0.000000] Trampoline variant of Tasks RCU enabled.
  286. [ 0.000000] Rude variant of Tasks RCU enabled.
  287. [ 0.000000] Tracing variant of Tasks RCU enabled.
  288. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
  289. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
  290. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  291. [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
  292. [ 0.000000] GICv3: 256 SPIs implemented
  293. [ 0.000000] GICv3: 0 Extended SPIs implemented
  294. [ 0.000000] GICv3: Distributor has no Range Selector support
  295. [ 0.000000] GICv3: 16 PPIs implemented
  296. [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
  297. [ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
  298. [ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @500000 (flat, esz 8, psz 64K, shr 0)
  299. [ 0.000000] ITS: using cache flushing for cmd queue
  300. [ 0.000000] GICv3: using LPI property table @0x00000000004d0000
  301. [ 0.000000] GIC: using cache flushing for LPI property table
  302. [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000000004e0000
  303. [ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
  304. [ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
  305. [ 0.000000] random: get_random_bytes called from start_kernel+0x690/0x848 with crng_init=0
  306. [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
  307. [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  308. [ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  309. [ 0.001432] Console: colour dummy device 80x25
  310. [ 0.002434] printk: console [tty0] enabled
  311. [ 0.002569] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
  312. [ 0.002616] pid_max: default: 32768 minimum: 301
  313. [ 0.002796] LSM: Security Framework initializing
  314. [ 0.002855] Yama: becoming mindful.
  315. [ 0.003015] AppArmor: AppArmor initialized
  316. [ 0.003132] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
  317. [ 0.003187] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
  318. [ 0.006926] rcu: Hierarchical SRCU implementation.
  319. [ 0.008153] Platform MSI: interrupt-controller@fee20000 domain created
  320. [ 0.008721] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
  321. [ 0.011060] EFI services will not be available.
  322. [ 0.011849] smp: Bringing up secondary CPUs ...
  323. [ 0.012876] Detected VIPT I-cache on CPU1
  324. [ 0.012921] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
  325. [ 0.012938] GICv3: CPU1: using allocated LPI pending table @0x00000000004f0000
  326. [ 0.013012] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
  327. [ 0.014122] Detected VIPT I-cache on CPU2
  328. [ 0.014156] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
  329. [ 0.014171] GICv3: CPU2: using allocated LPI pending table @0x0000000000580000
  330. [ 0.014220] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
  331. [ 0.015323] Detected VIPT I-cache on CPU3
  332. [ 0.015356] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
  333. [ 0.015371] GICv3: CPU3: using allocated LPI pending table @0x0000000000590000
  334. [ 0.015418] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
  335. [ 0.016559] CPU features: detected: Spectre-v2
  336. [ 0.016571] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
  337. [ 0.016580] Detected PIPT I-cache on CPU4
  338. [ 0.016616] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
  339. [ 0.016631] GICv3: CPU4: using allocated LPI pending table @0x00000000005a0000
  340. [ 0.016679] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
  341. [ 0.017737] Detected PIPT I-cache on CPU5
  342. [ 0.017766] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
  343. [ 0.017780] GICv3: CPU5: using allocated LPI pending table @0x00000000005b0000
  344. [ 0.017819] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
  345. [ 0.017989] smp: Brought up 1 node, 6 CPUs
  346. [ 0.018386] SMP: Total of 6 processors activated.
  347. [ 0.018411] CPU features: detected: 32-bit EL0 Support
  348. [ 0.018436] CPU features: detected: CRC32 instructions
  349. [ 0.018461] CPU features: detected: 32-bit EL1 Support
  350. [ 0.045975] CPU: All CPU(s) started at EL2
  351. [ 0.046056] alternatives: patching kernel code
  352. [ 0.049813] devtmpfs: initialized
  353. [ 0.065841] Registered cp15_barrier emulation handler
  354. [ 0.065884] Registered setend emulation handler
  355. [ 0.066138] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  356. [ 0.066228] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
  357. [ 0.069306] pinctrl core: initialized pinctrl subsystem
  358. [ 0.069990] DMI not present or invalid.
  359. [ 0.070583] NET: Registered protocol family 16
  360. [ 0.073731] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
  361. [ 0.074468] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
  362. [ 0.075799] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
  363. [ 0.075892] audit: initializing netlink subsys (disabled)
  364. [ 0.076148] audit: type=2000 audit(0.076:1): state=initialized audit_enabled=0 res=1
  365. [ 0.077456] thermal_sys: Registered thermal governor 'fair_share'
  366. [ 0.077464] thermal_sys: Registered thermal governor 'bang_bang'
  367. [ 0.077485] thermal_sys: Registered thermal governor 'step_wise'
  368. [ 0.077501] thermal_sys: Registered thermal governor 'user_space'
  369. [ 0.078056] cpuidle: using governor menu
  370. [ 0.078244] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  371. [ 0.078477] ASID allocator initialised with 65536 entries
  372. [ 0.079735] Serial: AMBA PL011 UART driver
  373. [ 0.153392] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
  374. [ 0.153423] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
  375. [ 0.153443] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
  376. [ 0.153461] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
  377. [ 0.159995] cryptd: max_cpu_qlen set to 1000
  378. [ 0.236242] raid6: neonx8 gen() 1664 MB/s
  379. [ 0.304388] raid6: neonx8 xor() 1239 MB/s
  380. [ 0.372556] raid6: neonx4 gen() 1683 MB/s
  381. [ 0.440701] raid6: neonx4 xor() 1270 MB/s
  382. [ 0.508862] raid6: neonx2 gen() 1501 MB/s
  383. [ 0.577018] raid6: neonx2 xor() 1177 MB/s
  384. [ 0.645186] raid6: neonx1 gen() 1177 MB/s
  385. [ 0.713330] raid6: neonx1 xor() 935 MB/s
  386. [ 0.781501] raid6: int64x8 gen() 994 MB/s
  387. [ 0.849683] raid6: int64x8 xor() 579 MB/s
  388. [ 0.917822] raid6: int64x4 gen() 985 MB/s
  389. [ 0.985955] raid6: int64x4 xor() 592 MB/s
  390. [ 1.054138] raid6: int64x2 gen() 926 MB/s
  391. [ 1.122273] raid6: int64x2 xor() 524 MB/s
  392. [ 1.190430] raid6: int64x1 gen() 724 MB/s
  393. [ 1.258610] raid6: int64x1 xor() 391 MB/s
  394. [ 1.258626] raid6: using algorithm neonx4 gen() 1683 MB/s
  395. [ 1.258641] raid6: .... xor() 1270 MB/s, rmw enabled
  396. [ 1.258656] raid6: using neon recovery algorithm
  397. [ 1.260064] reg-fixed-voltage vcc1v8-s3: Failed to register regulator: -517
  398. [ 1.260462] reg-fixed-voltage vcc3v0-sd: Failed to register regulator: -517
  399. [ 1.260733] vcc3v3_pcie: supplied by vcc12v_dcin
  400. [ 1.261375] reg-fixed-voltage vcc3v3-sys: Failed to register regulator: -517
  401. [ 1.261729] reg-fixed-voltage vcc5v0-host-regulator: Failed to register regulator: -517
  402. [ 1.262003] reg-fixed-voltage vcc5v0-typec-regulator: Failed to register regulator: -517
  403. [ 1.262161] vcc5v0_sys: supplied by vcc12v_dcin
  404. [ 1.262606] vcc5v0_usb: supplied by vcc12v_dcin
  405. [ 1.263245] iommu: Default domain type: Translated
  406. [ 1.266384] vgaarb: loaded
  407. [ 1.266924] SCSI subsystem initialized
  408. [ 1.267482] usbcore: registered new interface driver usbfs
  409. [ 1.267546] usbcore: registered new interface driver hub
  410. [ 1.267615] usbcore: registered new device driver usb
  411. [ 1.268275] pps_core: LinuxPPS API ver. 1 registered
  412. [ 1.268293] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  413. [ 1.268324] PTP clock support registered
  414. [ 1.268635] EDAC MC: Ver: 3.0.0
  415. [ 1.269941] NetLabel: Initializing
  416. [ 1.269961] NetLabel: domain hash size = 128
  417. [ 1.269975] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
  418. [ 1.270061] NetLabel: unlabeled traffic allowed by default
  419. [ 1.270454] clocksource: Switched to clocksource arch_sys_counter
  420. [ 1.393766] VFS: Disk quotas dquot_6.6.0
  421. [ 1.393875] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  422. [ 1.394781] AppArmor: AppArmor Filesystem Enabled
  423. [ 1.404249] NET: Registered protocol family 2
  424. [ 1.404582] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
  425. [ 1.408196] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
  426. [ 1.408488] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
  427. [ 1.409055] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
  428. [ 1.409734] TCP: Hash tables configured (established 32768 bind 32768)
  429. [ 1.409950] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
  430. [ 1.410131] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
  431. [ 1.410531] NET: Registered protocol family 1
  432. [ 1.410584] NET: Registered protocol family 44
  433. [ 1.410610] PCI: CLS 0 bytes, default 64
  434. [ 1.410850] Trying to unpack rootfs image as initramfs...
  435. [ 2.533434] Freeing initrd memory: 15040K
  436. [ 2.534630] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
  437. [ 2.535134] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
  438. [ 2.535838] kvm [1]: IPA Size Limit: 40 bits
  439. [ 2.537043] kvm [1]: vgic-v2@fff20000
  440. [ 2.537092] kvm [1]: GIC system register CPU interface enabled
  441. [ 2.537363] kvm [1]: vgic interrupt IRQ18
  442. [ 2.537681] kvm [1]: Hyp mode initialized successfully
  443. [ 2.549665] Initialise system trusted keyrings
  444. [ 2.549719] Key type blacklist registered
  445. [ 2.549937] workingset: timestamp_bits=44 max_order=20 bucket_order=0
  446. [ 2.556557] zbud: loaded
  447. [ 2.558428] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  448. [ 2.559321] fuse: init (API version 7.32)
  449. [ 2.560785] integrity: Platform Keyring initialized
  450. [ 2.625887] xor: measuring software checksum speed
  451. [ 2.629815] 8regs : 2532 MB/sec
  452. [ 2.633219] 32regs : 2917 MB/sec
  453. [ 2.637348] arm64_neon : 2398 MB/sec
  454. [ 2.637364] xor: using function: 32regs (2917 MB/sec)
  455. [ 2.637387] Key type asymmetric registered
  456. [ 2.637402] Asymmetric key parser 'x509' registered
  457. [ 2.637455] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
  458. [ 2.637664] io scheduler mq-deadline registered
  459. [ 2.637682] io scheduler kyber registered
  460. [ 2.637825] io scheduler bfq registered
  461. [ 2.642102] rockchip-usb2phy ff770000.syscon:usb2phy@e450: failed to create phy
  462. [ 2.643153] rockchip-usb2phy ff770000.syscon:usb2phy@e460: failed to create phy
  463. [ 2.655098] rockchip-pcie f8000000.pcie: host bridge /pcie@f8000000 ranges:
  464. [ 2.655161] rockchip-pcie f8000000.pcie: MEM 0x00fa000000..0x00fbdfffff -> 0x00fa000000
  465. [ 2.655195] rockchip-pcie f8000000.pcie: IO 0x00fbe00000..0x00fbefffff -> 0x00fbe00000
  466. [ 2.656169] rockchip-pcie f8000000.pcie: supply vpcie1v8 not found, using dummy regulator
  467. [ 2.656350] rockchip-pcie f8000000.pcie: supply vpcie0v9 not found, using dummy regulator
  468. [ 3.182529] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
  469. [ 3.183641] rockchip-pcie: probe of f8000000.pcie failed with error -110
  470. [ 3.191260] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
  471. [ 3.191289] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
  472. [ 3.192815] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
  473. [ 3.192842] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
  474. [ 3.197829] vdd_log: supplied by regulator-dummy
  475. [ 3.199538] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
  476. [ 3.203093] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 43, base_baud = 1500000) is a 16550A
  477. [ 3.203291] serial serial0: tty port ttyS0 registered
  478. [ 3.204478] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 44, base_baud = 1500000) is a 16550A
  479. [ 3.322341] printk: console [ttyS2] enabled
  480. [ 3.324132] Serial: AMBA driver
  481. [ 3.325860] cacheinfo: Unable to detect cache hierarchy for CPU 0
  482. [ 3.458586] loop: module loaded
  483. [ 3.466816] spi-nor spi0.0: gd25q128 (16384 Kbytes)
  484. [ 3.479488] 4 fixed-partitions partitions found on MTD device spi0.0
  485. [ 3.480059] Creating 4 MTD partitions on "spi0.0":
  486. [ 3.480496] 0x000000000000-0x000000060000 : "u-boot-spl"
  487. [ 3.506608] 0x000000060000-0x0000003f8000 : "u-boot"
  488. [ 3.526623] 0x0000003f8000-0x000000400000 : "u-boot-env"
  489. [ 3.546598] 0x000000400000-0x000001000000 : "user"
  490. [ 3.568198] libphy: Fixed MDIO Bus: probed
  491. [ 3.569313] tun: Universal TUN/TAP device driver, 1.6
  492. [ 3.570862] thunder_xcv, ver 1.0
  493. [ 3.571213] thunder_bgx, ver 1.0
  494. [ 3.571549] nicpf, ver 1.0
  495. [ 3.572906] e1000e: Intel(R) PRO/1000 Network Driver
  496. [ 3.573354] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
  497. [ 3.573929] igb: Intel(R) Gigabit Ethernet Network Driver
  498. [ 3.574412] igb: Copyright (c) 2007-2014 Intel Corporation.
  499. [ 3.574969] igbvf: Intel(R) Gigabit Virtual Function Network Driver
  500. [ 3.575529] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
  501. [ 3.576347] sky2: driver version 1.30
  502. [ 3.577425] VFIO - User Level meta-driver version: 0.3
  503. [ 3.586816] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  504. [ 3.587435] ehci-pci: EHCI PCI platform driver
  505. [ 3.587874] ehci-platform: EHCI generic platform driver
  506. [ 3.588889] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  507. [ 3.589458] ohci-pci: OHCI PCI platform driver
  508. [ 3.589907] ohci-platform: OHCI generic platform driver
  509. [ 3.591516] usbcore: registered new interface driver usb-storage
  510. [ 3.594556] mousedev: PS/2 mouse device common for all mice
  511. [ 3.596422] i2c /dev entries driver
  512. [ 3.604326] rk808 0-001b: chip id: 0x0
  513. [ 3.609249] rk808-regulator rk808-regulator: there is no dvs0 gpio
  514. [ 3.609831] rk808-regulator rk808-regulator: there is no dvs1 gpio
  515. [ 3.610389] rk808-regulator rk808-regulator: max buck steps per change: 8
  516. [ 3.611543] vdd_center: supplied by vcc5v0_sys
  517. [ 3.612734] vdd_cpu_l: supplied by vcc5v0_sys
  518. [ 3.613423] vcc_ddr: supplied by vcc5v0_sys
  519. [ 3.614375] vcc_1v8: supplied by vcc5v0_sys
  520. [ 3.615399] vcc1v8_dvp: supplied by vcc5v0_sys
  521. [ 3.616927] vcc3v0_touch: supplied by vcc5v0_sys
  522. [ 3.618470] vcca_1v8: supplied by vcc5v0_sys
  523. [ 3.620006] vcc_sdio: supplied by vcc5v0_sys
  524. [ 3.621377] vcca3v0_codec: supplied by vcc5v0_sys
  525. [ 3.622973] vcc_1v5: supplied by vcc5v0_sys
  526. [ 3.624336] vcca1v8_codec: supplied by vcc5v0_sys
  527. [ 3.625910] vcc_3v0: supplied by vcc5v0_sys
  528. [ 3.627174] rk808 0-001b: failed to register 12 regulator
  529. [ 3.634106] rk808-rtc rk808-rtc: registered as rtc0
  530. [ 3.635132] rk808-rtc rk808-rtc: setting system clock to 2013-01-18T08:50:36 UTC (1358499036)
  531. [ 3.637738] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
  532. [ 3.639063] vdd_cpu_b: supplied by vcc5v0_sys
  533. [ 3.642241] random: fast init done
  534. [ 3.642249] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
  535. [ 3.643901] vdd_gpu: supplied by vcc5v0_sys
  536. [ 3.652118] dw_wdt ff848000.watchdog: No valid TOPs array specified
  537. [ 3.655276] sdhci: Secure Digital Host Controller Interface driver
  538. [ 3.655835] sdhci: Copyright(c) Pierre Ossman
  539. [ 3.656259] Synopsys Designware Multimedia Card Interface Driver
  540. [ 3.658066] sdhci-pltfm: SDHCI platform and OF driver helper
  541. [ 3.658677] dwmmc_rockchip fe310000.mmc: IDMAC supports 32-bit address mode.
  542. [ 3.659038] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
  543. [ 3.659370] dwmmc_rockchip fe310000.mmc: Using internal DMA controller.
  544. [ 3.659990] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
  545. [ 3.660568] dwmmc_rockchip fe310000.mmc: Version ID is 270a
  546. [ 3.661161] dwmmc_rockchip fe320000.mmc: Version ID is 270a
  547. [ 3.661269] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 33,32 bit host data width,256 deep fifo
  548. [ 3.661387] mmc2: CQHCI version 5.10
  549. [ 3.661795] dwmmc_rockchip fe310000.mmc: DW MMC controller at irq 32,32 bit host data width,256 deep fifo
  550. [ 3.662326] ledtrig-cpu: registered to indicate activity on CPUs
  551. [ 3.663481] dwmmc_rockchip fe310000.mmc: allocated mmc-pwrseq
  552. [ 3.665096] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
  553. [ 3.665300] mmc_host mmc0: card is non-removable.
  554. [ 3.666165] hid: raw HID events driver (C) Jiri Kosina
  555. [ 3.666905] usbcore: registered new interface driver usbhid
  556. [ 3.667407] usbhid: USB HID core driver
  557. [ 3.671696] rockchip-saradc ff100000.saradc: failed to get regulator, -517
  558. [ 3.673497] drop_monitor: Initializing network drop monitor service
  559. [ 3.674953] NET: Registered protocol family 10
  560. [ 3.678822] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  561. [ 3.687456] mmc2: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
  562. [ 3.719347] Segment Routing with IPv6
  563. [ 3.719793] NET: Registered protocol family 17
  564. [ 3.720366] 8021q: 802.1Q VLAN Support v1.8
  565. [ 3.720795] Key type dns_resolver registered
  566. [ 3.721565] registered taskstats version 1
  567. [ 3.721948] Loading compiled-in X.509 certificates
  568. [ 3.726045] Loaded X.509 cert 'Build time autogenerated kernel key: 3795b2e16b9620035634919321440b15f322c25d'
  569. [ 3.730606] mmc_host mmc0: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
  570. [ 3.733291] zswap: loaded using pool zstd/z3fold
  571. [ 3.734104] Key type ._fscrypt registered
  572. [ 3.734528] Key type .fscrypt registered
  573. [ 3.734886] Key type fscrypt-provisioning registered
  574. [ 3.738732] Btrfs loaded, crc32c=crc32c-generic
  575. [ 3.760509] Key type encrypted registered
  576. [ 3.760943] AppArmor: AppArmor sha1 policy hashing enabled
  577. [ 3.787009] mmc_host mmc0: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
  578. [ 3.811656] reg-fixed-voltage vcc1v8-s3: Failed to register regulator: -517
  579. [ 3.813175] reg-fixed-voltage vcc3v0-sd: Failed to register regulator: -517
  580. [ 3.814370] vcc3v3_sys: supplied by vcc5v0_sys
  581. [ 3.815477] vcc5v0_host: supplied by vcc5v0_usb
  582. [ 3.816468] vcc5v0_typec: supplied by vcc5v0_usb
  583. [ 3.829012] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
  584. [ 3.829536] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
  585. [ 3.830403] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
  586. [ 3.831366] xhci-hcd xhci-hcd.1.auto: irq 77, io mem 0xfe900000
  587. [ 3.832328] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
  588. [ 3.833101] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  589. [ 3.833748] usb usb1: Product: xHCI Host Controller
  590. [ 3.834189] usb usb1: Manufacturer: Linux 5.10.63-rockchip64 xhci-hcd
  591. [ 3.834851] usb usb1: SerialNumber: xhci-hcd.1.auto
  592. [ 3.835866] hub 1-0:1.0: USB hub found
  593. [ 3.836278] hub 1-0:1.0: 1 port detected
  594. [ 3.837018] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
  595. [ 3.837524] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
  596. [ 3.838288] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
  597. [ 3.838977] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  598. [ 3.839869] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
  599. [ 3.840609] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  600. [ 3.841282] usb usb2: Product: xHCI Host Controller
  601. [ 3.841724] usb usb2: Manufacturer: Linux 5.10.63-rockchip64 xhci-hcd
  602. [ 3.842301] usb usb2: SerialNumber: xhci-hcd.1.auto
  603. [ 3.843291] hub 2-0:1.0: USB hub found
  604. [ 3.843677] hub 2-0:1.0: 1 port detected
  605. [ 3.847322] ehci-platform fe380000.usb: EHCI Host Controller
  606. [ 3.847857] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 3
  607. [ 3.848755] ehci-platform fe380000.usb: irq 35, io mem 0xfe380000
  608. [ 3.851500] mmc_host mmc0: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
  609. [ 3.862475] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
  610. [ 3.863275] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
  611. [ 3.864016] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  612. [ 3.864664] usb usb3: Product: EHCI Host Controller
  613. [ 3.865104] usb usb3: Manufacturer: Linux 5.10.63-rockchip64 ehci_hcd
  614. [ 3.865680] usb usb3: SerialNumber: fe380000.usb
  615. [ 3.866692] hub 3-0:1.0: USB hub found
  616. [ 3.867071] hub 3-0:1.0: 1 port detected
  617. [ 3.870556] ehci-platform fe3c0000.usb: EHCI Host Controller
  618. [ 3.871098] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 4
  619. [ 3.871939] ehci-platform fe3c0000.usb: irq 37, io mem 0xfe3c0000
  620. [ 3.886480] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
  621. [ 3.887266] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
  622. [ 3.888008] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  623. [ 3.888655] usb usb4: Product: EHCI Host Controller
  624. [ 3.889096] usb usb4: Manufacturer: Linux 5.10.63-rockchip64 ehci_hcd
  625. [ 3.889672] usb usb4: SerialNumber: fe3c0000.usb
  626. [ 3.890620] hub 4-0:1.0: USB hub found
  627. [ 3.890999] hub 4-0:1.0: 1 port detected
  628. [ 3.892403] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
  629. [ 3.893021] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 5
  630. [ 3.893851] ohci-platform fe3a0000.usb: irq 36, io mem 0xfe3a0000
  631. [ 3.954670] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
  632. [ 3.955413] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  633. [ 3.956059] usb usb5: Product: Generic Platform OHCI controller
  634. [ 3.956590] usb usb5: Manufacturer: Linux 5.10.63-rockchip64 ohci_hcd
  635. [ 3.957166] usb usb5: SerialNumber: fe3a0000.usb
  636. [ 3.958098] hub 5-0:1.0: USB hub found
  637. [ 3.958501] hub 5-0:1.0: 1 port detected
  638. [ 3.959914] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
  639. [ 3.960534] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 6
  640. [ 3.961384] ohci-platform fe3e0000.usb: irq 38, io mem 0xfe3e0000
  641. [ 4.022669] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
  642. [ 4.023411] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  643. [ 4.024057] usb usb6: Product: Generic Platform OHCI controller
  644. [ 4.024588] usb usb6: Manufacturer: Linux 5.10.63-rockchip64 ohci_hcd
  645. [ 4.025164] usb usb6: SerialNumber: fe3e0000.usb
  646. [ 4.026089] hub 6-0:1.0: USB hub found
  647. [ 4.026490] hub 6-0:1.0: 1 port detected
  648. [ 4.027470] rk808-regulator rk808-regulator: there is no dvs0 gpio
  649. [ 4.028051] rk808-regulator rk808-regulator: there is no dvs1 gpio
  650. [ 4.028607] rk808-regulator rk808-regulator: max buck steps per change: 8
  651. [ 4.029305] vdd_center: supplied by vcc5v0_sys
  652. [ 4.030054] vdd_cpu_l: supplied by vcc5v0_sys
  653. [ 4.030767] vcc_ddr: supplied by vcc5v0_sys
  654. [ 4.031442] vcc_1v8: supplied by vcc5v0_sys
  655. [ 4.032122] vcc1v8_dvp: supplied by vcc5v0_sys
  656. [ 4.033354] vcc3v0_touch: supplied by vcc5v0_sys
  657. [ 4.034643] vcca_1v8: supplied by vcc5v0_sys
  658. [ 4.035864] vcc_sdio: supplied by vcc5v0_sys
  659. [ 4.037074] vcca3v0_codec: supplied by vcc5v0_sys
  660. [ 4.038369] vcc_1v5: supplied by vcc5v0_sys
  661. [ 4.039608] vcca1v8_codec: supplied by vcc5v0_sys
  662. [ 4.040875] vcc_3v0: supplied by vcc5v0_sys
  663. [ 4.042111] vcc3v3_s3: supplied by vcc3v3_sys
  664. [ 4.042833] vcc3v3_s0: supplied by vcc3v3_sys
  665. [ 4.045031] rockchip-saradc ff100000.saradc: failed to get regulator, -517
  666. [ 4.045899] vcc1v8_s3: supplied by vcc_1v8
  667. [ 4.046155] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
  668. [ 4.046956] vcc3v0_sd: supplied by vcc3v3_sys
  669. [ 4.047430] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
  670. [ 4.048041] dwmmc_rockchip fe320000.mmc: Version ID is 270a
  671. [ 4.048596] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 33,32 bit host data width,256 deep fifo
  672. [ 4.050224] dwmmc_rockchip fe320000.mmc: Got CD GPIO
  673. [ 4.055825] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  674. [ 4.056544] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  675. [ 4.057248] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  676. [ 4.057950] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  677. [ 4.058685] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  678. [ 4.059389] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  679. [ 4.060091] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  680. [ 4.060792] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  681. [ 4.061494] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  682. [ 4.062195] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  683. [ 4.062928] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  684. [ 4.063630] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  685. [ 4.063876] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  686. [ 4.064333] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  687. [ 4.065862] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  688. [ 4.066795] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  689. [ 4.067498] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  690. [ 4.068200] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  691. [ 4.068901] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  692. [ 4.069602] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present!
  693. [ 4.071118] input: gpio-keys as /devices/platform/gpio-keys/input/input0
  694. [ 4.074119] of_cfs_init
  695. [ 4.074394] of_cfs_init: OK
  696. [ 4.075897] dw-apb-uart ff1a0000.serial: forbid DMA for kernel console
  697. [ 4.082136] Freeing unused kernel memory: 4352K
  698. [ 4.102617] Run /init as init process
  699. Loading, please wait...
  700. Starting version 245.4-4ubuntu3.15
  701. [ 4.848590] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
  702. [ 4.849228] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
  703. [ 4.850026] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
  704. [ 4.851116] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
  705. [ 4.851773] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
  706. [ 4.852296] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
  707. [ 4.852825] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
  708. [ 4.853512] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
  709. [ 4.854145] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
  710. [ 4.880979] rk_gmac-dwmac fe300000.ethernet: init for RGMII
  711. [ 4.886800] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
  712. [ 4.887483] rk_gmac-dwmac fe300000.ethernet: DWMAC1000
  713. [ 4.887966] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
  714. [ 4.888647] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
  715. [ 4.889333] rk_gmac-dwmac fe300000.ethernet: COE Type 2
  716. [ 4.889816] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
  717. [ 4.890516] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
  718. [ 4.891302] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
  719. [ 4.891848] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
  720. [ 4.892381] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  721. [ 4.981687] rockchip-vop ff8f0000.vop: Adding to iommu group 2
  722. [ 4.991559] rockchip-vop ff900000.vop: Adding to iommu group 3
  723. [ 5.027712] libphy: stmmac: probed
  724. [ 5.028053] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
  725. [ 5.029170] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
  726. Begin: Loading essential drivers ... done.
  727. Begin: Running /scripts/init-premount ... done.
  728. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done.
  729. Begin: Running /scripts/nfs-premount ... done.
  730. Internet Systems Consortium DHCP Client 4.4.1
  731. Copyright 2004-2018 Internet Systems Consortium.
  732. All rights reserved.
  733. For info, please visit https://www.isc.org/software/dhcp/
  734.  
  735. [ 5.266567] rk_gmac-dwmac fe300000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=POLL)
  736. [ 5.282110] rk_gmac-dwmac fe300000.ethernet eth0: No Safety Features support found
  737. [ 5.282855] rk_gmac-dwmac fe300000.ethernet eth0: PTP not supported by HW
  738. [ 5.284341] rk_gmac-dwmac fe300000.ethernet eth0: configuring for phy/rgmii link mode
  739. Listening on LPF/eth0/e6:41:ab:b7:a6:86
  740. Sending on LPF/eth0/e6:41:ab:b7:a6:86
  741. Sending on Socket/fallback
  742. DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 (xid=0x864ebf79)
  743. [ 8.391421] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
  744. [ 8.392252] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  745. No DHCPOFFERS received.
  746. No working leases in persistent database - sleeping.
  747. Internet Systems Consortium DHCP Client 4.4.1
  748. Copyright 2004-2018 Internet Systems Consortium.
  749. All rights reserved.
  750. For info, please visit https://www.isc.org/software/dhcp/
  751.  
  752. Listening on LPF/eth0/e6:41:ab:b7:a6:86
  753. Sending on LPF/eth0/e6:41:ab:b7:a6:86
  754. Sending on Socket/fallback
  755. DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 (xid=0xbb317f57)
  756. DHCPOFFER of 192.168.0.156 from 192.168.0.1
  757. DHCPREQUEST for 192.168.0.156 on eth0 to 255.255.255.255 port 67 (xid=0x577f31bb)
  758. DHCPACK of 192.168.0.156 from 192.168.0.1 (xid=0xbb317f57)
  759. bound to 192.168.0.156 -- renewal in 3255 seconds.
  760. [ 8.687938] FS-Cache: Loaded
  761. [ 8.757573] RPC: Registered named UNIX socket transport module.
  762. [ 8.758122] RPC: Registered udp transport module.
  763. [ 8.758575] RPC: Registered tcp transport module.
  764. [ 8.758999] RPC: Registered tcp NFSv4.1 backchannel transport module.
  765. [ 8.852266] FS-Cache: Netfs 'nfs' registered for caching
  766. done.
  767. Begin: Running /scripts/nfs-bottom ... done.
  768. Begin: Running /scripts/init-bottom ... Running /usr/sbin/ltsp initrd-bottom
  769. Running: mount -t tmpfs -o mode=0755 tmpfs /run/initramfs/ltsp
  770. Running: mount -t squashfs -o ro /root/images/rockpro64.img /run/initramfs/ltsp/0/looproot
  771. Running: mount -t overlay -o upperdir=/run/initramfs/ltsp/0/up,lowerdir=/run/initramfs/ltsp/0/looproot,workdir=/run/initramfs/ltsp/0/work /run/initramfs/ltsp /root/
  772. [ 9.224959] overlayfs: "xino" feature enabled using 2 upper inode bits.
  773. done.
  774. [ 10.738744] random: ln: uninitialized urandom read (6 bytes read)
  775. [ 11.012542] random: pwmerge: uninitialized urandom read (24 bytes read)
  776. [ 11.779175] random: pam-auth-update: uninitialized urandom read (4 bytes read)
  777. [ 11.900010] random: frontend: uninitialized urandom read (4 bytes read)
  778. [ 13.132557] random: pam-auth-update: uninitialized urandom read (4 bytes read)
  779. [ 14.045959] random: ln: uninitialized urandom read (6 bytes read)
  780. [ 14.373110] random: update-rc.d: uninitialized urandom read (4 bytes read)
  781. [ 14.489370] random: update-rc.d: uninitialized urandom read (4 bytes read)
  782. [ 14.570076] random: update-rc.d: uninitialized urandom read (4 bytes read)
  783. [ 15.913135] systemd[1]: System time before build time, advancing clock.
  784. [ 15.931403] systemd[1]: Inserted module 'autofs4'
  785. [ 15.983849] systemd[1]: systemd 245.4-4ubuntu3.15 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
  786. [ 15.986880] systemd[1]: Detected architecture arm64.
  787.  
  788. Welcome to Ubuntu 20.04.3 LTS!
  789.  
  790. [ 16.051886] systemd[1]: Set hostname to <rockpro64-pxe>.
  791. [ 16.509850] systemd[1]: Configuration file /lib/systemd/system/ats.service is marked world-inaccessible. This has no effect as configuration data is accessible via APIs without restrictions. Proceeding anyway.
  792. [ 16.670055] systemd[1]: Created slice system-modprobe.slice.
  793. [ OK ] Created slice system-modprobe.slice.
  794. [ 16.684272] systemd[1]: Created slice system-serial\x2dgetty.slice.
  795. [ OK ] Created slice system-serial\x2dgetty.slice.
  796. [ 16.695954] systemd[1]: Created slice User and Session Slice.
  797. [ OK ] Created slice User and Session Slice.
  798. [ 16.706640] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
  799. [ 16.708202] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
  800. [ OK ] Started Forward Password R…uests to Wall Directory Watch.
  801. [ 16.723588] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
  802. [ OK ] Set up automount Arbitrary…s File System Automount Point.
  803. [ 16.734716] systemd[1]: Reached target Local Encrypted Volumes.
  804. [ OK ] Reached target Local Encrypted Volumes.
  805. [ 16.746766] systemd[1]: Reached target Slices.
  806. [ OK ] Reached target Slices.
  807. [ 16.758641] systemd[1]: Reached target Swap.
  808. [ OK ] Reached target Swap.
  809. [ 16.770616] systemd[1]: Reached target System Time Set.
  810. [ OK ] Reached target System Time Set.
  811. [ 16.772206] systemd[1]: Listening on initctl Compatibility Named Pipe.
  812. [ OK ] Listening on initctl Compatibility Named Pipe.
  813. [ 16.785096] systemd[1]: Listening on Journal Audit Socket.
  814. [ OK ] Listening on Journal Audit Socket.
  815. [ 16.795211] systemd[1]: Listening on Journal Socket (/dev/log).
  816. [ OK ] Listening on Journal Socket (/dev/log).
  817. [ 16.807317] systemd[1]: Listening on Journal Socket.
  818. [ OK ] Listening on Journal Socket.
  819. [ 16.819368] systemd[1]: Listening on udev Control Socket.
  820. [ OK ] Listening on udev Control Socket.
  821. [ 16.830998] systemd[1]: Listening on udev Kernel Socket.
  822. [ OK ] Listening on udev Kernel Socket.
  823. [ 16.838172] systemd[1]: Mounting Huge Pages File System...
  824. Mounting Huge Pages File System...
  825. [ 16.856163] systemd[1]: Mounting POSIX Message Queue File System...
  826. Mounting POSIX Message Queue File System...
  827. [ 16.863195] systemd[1]: Mounting RPC Pipe File System...
  828. Mounting RPC Pipe File System...
  829. [ 16.879821] systemd[1]: Mounting Kernel Debug File System...
  830. Mounting Kernel Debug File System...
  831. [ 16.895921] systemd[1]: Mounting Kernel Trace File System...
  832. Mounting Kernel Trace File System...
  833. [ 16.917408] systemd[1]: Starting Restore / save the current clock...
  834. Starting Restore / save the current clock...
  835. [ 16.928253] systemd[1]: Starting Set the console keyboard layout...
  836. Starting Set the console keyboard layout...
  837. [ 16.936854] systemd[1]: Starting Create list of static device nodes for the current kernel...
  838. Starting Create list of st…odes for the current kernel...
  839. [ 16.950766] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped.
  840. [ 16.957043] systemd[1]: Started Nameserver information manager.
  841. [ OK ] Started Nameserver information manager.
  842. [ 16.967441] systemd[1]: Reached target Network (Pre).
  843. [ OK ] Reached target Network (Pre).
  844. [ 16.979890] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
  845. [ 16.988781] systemd[1]: Starting Load Kernel Modules...
  846. Starting Load Kernel Modules...
  847. [ 17.004140] systemd[1]: Starting Remount Root and Kernel File Systems...
  848. Starting Remount Root and Kernel File Systems...
  849. [ 17.024102] systemd[1]: Starting udev Coldplug all Devices...
  850. Starting udev Coldplug all Devices...
  851. [ 17.045460] systemd[1]: Mounted Huge Pages File System.
  852. [ OK ] Mounted Huge Pages File System.
  853. [ 17.048042] systemd[1]: Mounted POSIX Message Queue File System.
  854. [ OK ] Mounted POSIX Message Queue File System.
  855. [ 17.063695] systemd[1]: Mounted RPC Pipe File System.
  856. [ OK ] Mounted RPC Pipe File System.
  857. [ 17.075625] systemd[1]: Mounted Kernel Debug File System.
  858. [ OK ] Mounted Kernel Debug File System.
  859. [ 17.077804] systemd[1]: Mounted Kernel Trace File System.
  860. [ OK ] Mounted Kernel Trace File System.
  861. [ 17.082732] systemd[1]: Finished Restore / save the current clock.
  862. [ OK ] Finished Restore / save the current clock.
  863. [ 17.102297] systemd[1]: Finished Create list of static device nodes for the current kernel.
  864. [ OK ] Finished Create list of st… nodes for the current kernel.
  865. [ 17.125910] systemd[1]: Finished Load Kernel Modules.
  866. [ OK ] Finished Load Kernel Modules.
  867. [ 17.144499] systemd[1]: Finished Remount Root and Kernel File Systems.
  868. [ OK ] Finished Remount Root and Kernel File Systems.
  869. [ 17.164681] systemd[1]: Mounting FUSE Control File System...
  870. Mounting FUSE Control File System...
  871. [ 17.186695] systemd[1]: Mounting Kernel Configuration File System...
  872. Mounting Kernel Configuration File System...
  873. [ 17.191227] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
  874. [ 17.192508] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
  875. [ 17.201570] systemd[1]: Starting Load/Save Random Seed...
  876. Starting Load/Save Random Seed...
  877. [ 17.211501] systemd[1]: Starting Apply Kernel Variables...
  878. Starting Apply Kernel Variables...
  879. [ 17.221596] systemd[1]: Starting Create System Users...
  880. Starting Create System Users...
  881. [ 17.233975] systemd[1]: Mounted FUSE Control File System.
  882. [ OK ] Mounted FUSE Control File System.
  883. [ 17.237172] systemd[1]: Mounted Kernel Configuration File System.
  884. [ OK ] Mounted Kernel Configuration File System.
  885. [ OK ] Finished Create System Users.
  886. Starting Create Static Device Nodes in /dev...
  887. [ OK ] Finished Apply Kernel Variables.
  888. [ OK ] Finished Set the console keyboard layout.
  889. [ OK ] Finished Create Static Device Nodes in /dev.
  890. [ OK ] Reached target Local File Systems (Pre).
  891. [ OK ] Reached target Local File Systems.
  892. Starting Armbian ZRAM config...
  893. Starting Set console font and keymap...
  894. Starting Preprocess NFS configuration...
  895. Starting udev Kernel Device Manager...
  896. [ OK ] Finished Set console font and keymap.
  897. [ OK ] Finished Preprocess NFS configuration.
  898. [ OK ] Reached target NFS client services.
  899. [ OK ] Reached target Remote File Systems (Pre).
  900. [ OK ] Reached target Remote File Systems.
  901. [ OK ] Started udev Kernel Device Manager.
  902. [ OK ] Finished udev Coldplug all Devices.
  903. Starting Helper to synchronize boot up for ifupdown...
  904. [ OK ] Found device /dev/ttyS2.
  905. [ OK ] Found device /sys/subsystem/net/devices/eth0.
  906. [ OK ] Started ifup for eth0.
  907. [ 18.941416] OF: graph: no port node found in /i2c@ff3d0000/typec-portc@22
  908. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
  909. Starting Load/Save RF Kill Switch Status...
  910. [ OK ] Started Load/Save RF Kill Switch Status.
  911. [ OK ] Reached target Bluetooth.
  912. [ OK ] Finished Helper to synchronize boot up for ifupdown.
  913. Starting Raise network interfaces...
  914. [ OK ] Finished Raise network interfaces.
  915. [ 21.222457] Bluetooth: hci0: command 0x0c03 tx timeout
  916. [ OK ] Finished Load/Save Random Seed.
  917. [ OK ] Finished Armbian ZRAM config.
  918. Starting Armbian memory supported logging...
  919. [ OK ] Finished Armbian memory supported logging.
  920. Starting Journal Service...
  921. [ OK ] Started Journal Service.
  922. Starting Flush Journal to Persistent Storage...
  923. [ OK ] Finished Flush Journal to Persistent Storage.
  924. Starting Create Volatile Files and Directories...
  925. [ OK ] Finished Create Volatile Files and Directories.
  926. [ OK ] Started Entropy daemon using the HAVEGE algorithm.
  927. Starting Network Name Resolution...
  928. Starting Update UTMP about System Boot/Shutdown...
  929. [ OK ] Finished Update UTMP about System Boot/Shutdown.
  930. [ OK ] Reached target System Initialization.
  931. [ OK ] Started resolvconf-pull-resolved.path.
  932. [ OK ] Started Daily Cleanup of Temporary Directories.
  933. [ OK ] Reached target Paths.
  934. [ OK ] Listening on D-Bus System Message Bus Socket.
  935. [ OK ] Reached target Sockets.
  936. Starting Armbian hardware monitoring...
  937. Starting Armbian hardware optimization...
  938. [ OK ] Finished Armbian hardware monitoring.
  939. [ OK ] Started Network Name Resolution.
  940. [ OK ] Reached target Host and Network Name Lookups.
  941. [ 17.233975] systemd[1]: Mounted FUSE Control File System.
  942. [ OK ] Mounted FUSE Control File System.
  943. [ 17.237172] systemd[1]: Mounted Kernel Configuration File System.
  944. [ OK ] Mounted Kernel Configuration File System.
  945. [ OK ] Finished Create System Users.
  946. Starting Create Static Device Nodes in /dev...
  947. [ OK ] Finished Apply Kernel Variables.
  948. [ OK ] Finished Set the console keyboard layout.
  949. [ OK ] Finished Create Static Device Nodes in /dev.
  950. [ OK ] Reached target Local File Systems (Pre).
  951. [ OK ] Reached target Local File Systems.
  952. Starting Armbian ZRAM config...
  953. Starting Set console font and keymap...
  954. Starting Preprocess NFS configuration...
  955. Starting udev Kernel Device Manager...
  956. [ OK ] Finished Set console font and keymap.
  957. [ OK ] Finished Preprocess NFS configuration.
  958. [ OK ] Reached target NFS client services.
  959. [ OK ] Reached target Remote File Systems (Pre).
  960. [ OK ] Reached target Remote File Systems.
  961. [ OK ] Started udev Kernel Device Manager.
  962. [ OK ] Finished udev Coldplug all Devices.
  963. Starting Helper to synchronize boot up for ifupdown...
  964. [ OK ] Found device /dev/ttyS2.
  965. [ OK ] Found device /sys/subsystem/net/devices/eth0.
  966. [ OK ] Started ifup for eth0.
  967. [ 18.941416] OF: graph: no port node found in /i2c@ff3d0000/typec-portc@22
  968. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
  969. Starting Load/Save RF Kill Switch Status...
  970. [ OK ] Started Load/Save RF Kill Switch Status.
  971. [ OK ] Reached target Bluetooth.
  972. [ OK ] Finished Helper to synchronize boot up for ifupdown.
  973. Starting Raise network interfaces...
  974. [ OK ] Finished Raise network interfaces.
  975. [ 21.222457] Bluetooth: hci0: command 0x0c03 tx timeout
  976. [ OK ] Finished Load/Save Random Seed.
  977. [ OK ] Finished Armbian ZRAM config.
  978. Starting Armbian memory supported logging...
  979. [ OK ] Finished Armbian memory supported logging.
  980. Starting Journal Service...
  981. [ OK ] Started Journal Service.
  982. Starting Flush Journal to Persistent Storage...
  983. [ OK ] Finished Flush Journal to Persistent Storage.
  984. Starting Create Volatile Files and Directories...
  985. [ OK ] Finished Create Volatile Files and Directories.
  986. [ OK ] Started Entropy daemon using the HAVEGE algorithm.
  987. Starting Network Name Resolution...
  988. Starting Update UTMP about System Boot/Shutdown...
  989. [ OK ] Finished Update UTMP about System Boot/Shutdown.
  990. [ OK ] Reached target System Initialization.
  991. [ OK ] Started resolvconf-pull-resolved.path.
  992. [ OK ] Started Daily Cleanup of Temporary Directories.
  993. [ OK ] Reached target Paths.
  994. [ OK ] Listening on D-Bus System Message Bus Socket.
  995. [ OK ] Reached target Sockets.
  996. Starting Armbian hardware monitoring...
  997. Starting Armbian hardware optimization...
  998. [ OK ] Finished Armbian hardware monitoring.
  999. [ OK ] Started Network Name Resolution.
  1000. [ OK ] Reached target Host and Network Name Lookups.
  1001. [ OK ] Finished Armbian hardware optimization.
  1002. [ OK ] Reached target Basic System.
  1003. Starting Save/Restore Sound Card State...
  1004. [ OK ] Started ATS - Active Thermal Service.
  1005. [ OK ] Started Regular background program processing daemon.
  1006. [ OK ] Started D-Bus System Message Bus.
  1007. Starting Network Manager...
  1008. [ OK ] Started Save initial kernel messages after boot.
  1009. Starting Remove Stale Onli…t4 Metadata Check Snapshots...
  1010. Starting LSB: Load kernel …d to enable cpufreq scaling...
  1011. Starting Dispatcher daemon for systemd-networkd...
  1012. Starting resolvconf-pull-resolved.service...
  1013. Starting Self Monitoring a…g Technology (SMART) Daemon...
  1014. Starting Resets System Activity Data Collector...
  1015. Starting Login Service...
  1016. Starting WPA supplicant...
  1017. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots.
  1018. [ OK ] Finished Resets System Activity Data Collector.
  1019. [ OK ] Finished Save/Restore Sound Card State.
  1020. [ OK ] Reached target Sound Card.
  1021. [ OK ] Finished resolvconf-pull-resolved.service.
  1022. [ OK ] Started Self Monitoring an…ing Technology (SMART) Daemon.
  1023. [ OK ] Started LSB: Load kernel m…ded to enable cpufreq scaling.
  1024. [ OK ] Started Login Service.
  1025. Starting LSB: set CPUFreq kernel parameters...
  1026. [ OK ] Started WPA supplicant.
  1027. [ OK ] Started LSB: set CPUFreq kernel parameters.
  1028. Starting LSB: Set sysfs variables from /etc/sysfs.conf...
  1029. [ OK ] Started LSB: Set sysfs variables from /etc/sysfs.conf.
  1030. [ OK ] Started Network Manager.
  1031. [ OK ] Reached target Network.
  1032. [ OK ] Reached target Network is Online.
  1033. Starting chrony, an NTP client/server...
  1034. Starting LSB: Advanced IEEE 802.11 management daemon...
  1035. Starting LTSP startup tasks...
  1036. Starting OpenVPN service...
  1037. Starting /etc/rc.local Compatibility...
  1038. Starting Permit User Sessions...
  1039. [ OK ] Started vnStat network traffic monitor.
  1040. [ OK ] Started Dispatcher daemon for systemd-networkd.
  1041. [ OK ] Started LSB: Advanced IEEE 802.11 management daemon.
  1042. [ OK ] Finished OpenVPN service.
  1043. [ OK ] Started /etc/rc.local Compatibility.
  1044. [ OK ] Finished Permit User Sessions.
  1045. [ OK ] Started chrony, an NTP client/server.
  1046. [ OK ] Reached target System Time Synchronized.
  1047. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
  1048. [ OK ] Started Discard unused blocks once a week.
  1049. [ OK ] Reached target Timers.
  1050. [ OK ] Started Serial Getty on ttyS2.
  1051. Starting Set console scheme...
  1052. Starting Hostname Service...
  1053. [ OK ] Started LTSP startup tasks.
  1054. [ OK ] Finished Set console scheme.
  1055. [ OK ] Created slice system-getty.slice.
  1056. [ OK ] Started Getty on tty1.
  1057. [ OK ] Reached target Login Prompts.
  1058. [ OK ] Reached target Multi-User System.
  1059. [ OK ] Reached target Graphical Interface.
  1060. Starting Update UTMP about System Runlevel Changes...
  1061. [ OK ] Finished Update UTMP about System Runlevel Changes.
  1062. [ OK ] Started Hostname Service.
  1063. [ 29.414553] Bluetooth: hci0: BCM: Reset failed (-110)
  1064.  
  1065. Ubuntu 20.04.3 LTS rockpro64-pxe ttyS2
  1066.  
  1067. rockpro64-pxe login:
  1068. rockpro64-pxe login:
  1069. rockpro64-pxe login:
Advertisement
Advertisement
Advertisement
RAW Paste Data Copied
Advertisement